TECHNICAL DATA BROCHURE
IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATION.
Seat Adjustment
Loosen Bolts on sliding brackets under each side of seat, slide seat forward or rearward to
desired position. Re-tighten bolts. Do not operate mower with bracket bolts in a loose
condition.
Mower Blade Operation
To start mower blades, move lever on floor slowly to "ENGAGE" position. To stop
mower blades, move lever on floor slowly to "DISENGAGE" position.
Body Removal
1. Disconnect throttle cable from engine.
2. Disconnect the rear wiring loom (P/N 4109) from the body by lightly squeezing the Econo-
Seal plug. This is located at the left rear of the body.
3. Note: Loosen bolts that hold body switch (P/N 4079) and slide switch away from engaging
rod. Tighten one bolt just enough to hold switch in this position until body is
reassembled.
4. Remove 4 control lever bolts and remove upper control levers (P/N 1501L-1501R).
5. Remove engaging handle (P/N 6089) by removing bolt and nut under handle.
6. Remove the 2 attach nuts on floor of body and 2 sheet metal screws at the rear of body.
7. Place height adjustment lever in vertical position, engage parking brake and carefully lift
body up and off chassis.
8. Reverse the above procedure for assembly.
Safety Checks
With the mower deck in the engaged position slide the body switch (P/N 4079) toward
the engaging rod (P/N 6087-1) until the switch leaf just makes contact with the
switch button. Tighten both bolts in switch bracket.
With mower deck engaged, attempt to start engine in all cutting height positions.
If engine starts in any cutting height position, re -adjust the switch. Disengage
the mower deck and start the engine in each cutting height position. If engine
fails to start in any cutting height position, re-adjust switch.
With operator in normal mowing/position, engage mower deck and remove weight from
seat. The engine should stop. Repeat this procedure in each cutting height
position. If engine does not stop when operator rises from seat in each cutting
height position, return to an authorized Dixon dealer for adjustment f>r repairs.
Parking Brake Adjustment
Remove body as described above. Tighten nut on brake rod (P/N2533) (Located in front of the
transaxle on each side.), just enough to prevent brake from slipping when engaged. CAUTION:
Over tightening may cause premature wear on brake band (P/N 5085).
Mower Drive Belt Adjustment
Belt tension for mower drive belt (P/N 2412) is adjusted by loosening nut on the connecting
arm assembly (P/N 2171 -A ) and turning bolt to achieve desired tension. Re-tighten nut.
Tension should be checked with belt in engaged position.
Removing Mower Deck
1.
Remove engaging handle (P/N 6089) by removing bolt and nut under handle.
2. Loosen belt keeper (P/N 2234) located under engine by loosening 2 rear engine
mount bolts to allow mower deck drive belt to come free of rear pulley.
Re-tighten belt keeper,
(continued on back)
1
DIXON INDUSTRIES, INC. B OX 484, COFFEYVILLE, KANSAS 67337 (316) 251-2000
D.I. Form S-35 (Rev. 6/83)
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART # NAME
ART # NAME
PART # NAME
1015
1020
1022
Caster Weldment
2444
2449
2452
2456
2460
2463
2465
2466
2468
2469
2470
2501
2504
2507
2508
2509
2514
2515
2524
Battery Ground Cable
4122
4124
4148
5005
5007
Body Wiring Loom
Caster Axle
Caster Nipple
Solenoid
Seat Angle
Discup
Caster Wheel & T1re
Engaging Idler Bshg.
Model Decal-ZTR 308
Parking Brake Decal
Seat
1022A Caster Wheel Bearing
I030
I039
1108
1109
Upper Lift Link-Rear
Lower Lift Link
Cone Frame
5009R Cradle
Tire - Front Wheel
Inner Tube - Front Wheel
Rear Tire(16x6.5-8)
Rear Rim (16x6.5-8)
Double Engine Pulley
V-Belt
5009L
5012
5013
5015
5016
5018
5019
5021
Cradle
Cradle Shaft
1501R Upper Control Lever
ISOIL Upper Control Lever
Cone Frame Shaft
24T Sprocket
1507
1536
1540
543
Wheel/Deck Hub Bearing
Chain Connecting Link
Engine Shaft Key
Lift Knob
Transaxle Pulley
Rear Tube' Weldment
Front Tube
Molded Cone
9T Sprocket-Narrow
Transaxle Chain
9T Sprocket-Wide
Support L
544
Bellcrank
Support R
5024-1 Cradle Spring
560-1 Battery Splash Guard
Support Shaft
5028
5036
5046
5047
5053
6059
6089
6107
Transaxle Bearing
Pivot Spring
574
606
647
654
655
657
Brake Pivot Weldment
Brake Mount Weldment
Control Pin
Torque Rod Stiffener R
Torque Rod Stiffener L
Transaxle
Positive Neutral R
Positive Neutral S
Brake Arm Retainer
Flat Idler Pulley
Engaging Handle
Deck Pin
Transaxle Idler Weld.
Transaxle Idler Pulley
Transaxle Idler Spring
2600-3 Mower Deck Assy.
2601-2 Mower Deck Weldment
2612
Engaging Idler Weld.
2000-2 Frame Weldment
2620-1 Engaging Rod
2077
2100
2105
2154
2155
2159
2164
Walking Beam Weldment
2626
2640
2641
2642
2645
2647
2648
2668
2823
3029
3120
3123
3129
3502
3504
3507
3508
3511
3521
3531
3532
3533
3536
Deflector Sheet
6136-2 Engaging Cam Weld.
Bumper Weldment
Mower Deck Hub Assy.
Mower Deck Hub Sub-Assy.
Mower Deck Hub
6159
Stabilizer Arm Wel
Bumper Pad
Hub Pulley Spacer
Hub Bearing Spacer
Engaging Idler Spacer
Support Sprocket Spacer
Blade Shaft Weldment
Blade Washer
Deck Hub Key
2165-1 Torque Rod
Stiffener
2166
Pivot Bolt
Oil Drain Assy.
2171A Connecting Arm Assy.
Front Grommet
2171-1 Connecting Arm Weldment
Nylon Shoulder Bshg.
Control Pin
2172
2176
2179
2180
2204
Swivel Fitting
Body
Plastic Tube Closure
Hand Grip
Switch Bracket-Body
Switch Bracket-Sw. Sect.
Wheel Hub
Double Ball Joint
Floor Pad -Long
2214R Brake Arm Weldment R
2214L Brake Arm Weldment L
Floor Pad -Short
Adhesive Bumper Pad
Engaging Cam Mount Bshg.
Decal-Operating Inst.
Decal-Blade Drive
Decal-Cutting Height
Warning Label-Danger
2221
Transaxle Shim 16ga
2222
Transaxle Shim 22ga
2225
Battery Box Weldment
2231 Lower Control Lever Assy
2234 Belt Keeper
4005B Throttle Cable
2237 Tie Bar Assy.
4006-2 Solenoid-Starter Cable
4006-8 Solenoid-Battery Cable
4007-1 Battery-12V
2238 Tie Bar
2240 Short Brake Rod Assy.
2402 Rear Wheel & Tire
4009
4013
4047
4067
Wire Clip(not shown)
Wire Tie (not shown)
Seat Switch
406
408
411
412
413
414
417
30" Mower Blade
Drive Chain Assy.
Mower Deck V-Pulley
Deck Drive Belt
Ignition Switch
V-Idler Pulley
4067A Switch Key (for 4067)
Engaging Idler Tension Sprg
Control Rod Assy
4075
4079
4092
4109
10 AMP Fuse
Body Switch
418 Long Brake Rod Assy
422 Name Decal
436 Switch Decal
Fuse Holder
Rear Wiring Loom
4115
Wiring Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
|