Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Op e r a t O r ’s Ma n u a l
Self Propelled Mower — Model CC46 ES
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-06426
(November 10, 2010)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safe Operation Practices
2
WARNING: This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
WARNING: Battery posts, terminals, and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and reproductive
harm. Wash hands after handling.
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing objects. Failure to observe the following safety instructions could
result in serious injury or death.
6.
Thoroughly inspect the area where the equipment is to be
used. Remove all stones, sticks, wire, bones, toys and other
foreign objects, which could be tripped over or picked up
and thrown by the blade. Thrown objects can cause serious
personal injury.
General Operation
1.
Read this operator’s manual carefully in its entirety before
attempting to assemble this machine. Read, understand,
and follow all instructions on the machine and in the
manual(s) before operation. Keep this manual in a safe
place for future and regular reference and for ordering
replacement parts.
7.
Plan your mowing pattern to avoid discharge of material
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction,
which may cause discharged material to ricochet back
toward the operator.
2.
Be completely familiar with the controls and the proper use
of this machine before operating it.
3.
This machine is a precision piece of power equipment,
not a plaything. Therefore, exercise extreme caution at all
times. This machine has been designed to perform one job:
to mow grass. Do not use it for any other purpose.
8.
9.
To help avoid blade contact or a thrown object injury,
stay in operator zone behind handles and keep children,
bystanders, helpers and pets at least 75 feet from mower
while it is in operation. Stop machine if anyone enters area.
4.
5.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.
Always wear safety glasses or safety goggles during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
10. Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Shirts and pants that cover the arms
and legs and steel-toed shoes are recommended. Never
operate this machine in bare feet, sandals, slippery or light-
weight (e.g. canvas) shoes.
Only responsible individuals who are familiar with these
rules of safe operation should be allowed to use this
machine.
11. Do not put hands or feet near rotating parts or under the
cutting deck. Contact with blade can amputate fingers,
hands, toes and feet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
12. A missing or damaged discharge cover can cause blade
27. When starting engine, pull cord slowly until resistance
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster than
you can let go. Broken bones, fractures, bruises or sprains
could result.
contact or thrown object injuries.
13. Many injuries occur as a result of the mower being pulled
over the foot during a fall caused by slipping or tripping.
Do not hold on to the mower if you are falling; release the
handle immediately.
28. If situations occur which are not covered in this manual,
use care and good judgement. Contact Customer Support
for assistance or the name of the nearest service dealer.
14. Never pull the mower back toward you while you are
walking. If you must back the mower away from a wall or
obstruction first look down and behind to avoid tripping
and then follow these steps:
Slope Operation
Slopes are a major factor related to slip and fall accidents, which
can result in severe injury. Operation on slopes requires extra
caution. If you feel uneasy on a slope, do not mow it. For your
safety, use the slope gauge included as part of this manual to
measure slopes before operating this machine on a sloped or
hilly area. If the slope is greater than 15 degrees, do not mow it.
a. Step back from mower to fully extend your arms.
b. Be sure you are well balanced with sure footing.
c. Pull the mower back slowly, no more than half way
toward you.
d. Repeat these steps as needed.
Do:
15. Do not operate the mower while under the influence of
1.
Mow across the face of slopes; never up and down. Exercise
extreme caution when changing direction on slopes.
alcohol or drugs.
16. Do not engage the self-propelled mechanism on machines
2.
Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide
obstacles.
so equipped while starting engine.
17. The blade control is a safety device. Never attempt to
bypass its operation. Doing so makes the safety device
inoperative and may result in personal injury through
contact with the rotating blade. The blade control must
operate easily in both directions and automatically return
to the disengaged position when released.
3.
Always be sure of your footing. A slip and fall can cause
serious personal injury. If you feel you are losing your
balance, release the blade control handle immediately and
the blade will stop rotating within three (3) seconds.
18. Never operate the mower in wet grass. Always be sure of
your footing. A slip and fall can cause serious personal
injury. If you feel you are losing your footing, release the
blade control handle immediately and the blade will stop
rotating within three seconds.
Do Not:
1.
2.
3.
Do not mow near drop-offs, ditches or embankments, you
could lose your footing or balance.
Do not mow slopes greater than 15 degrees as shown on
the slope gauge.
19. Mow only in daylight or good artificial light. Walk, never
run.
Do not mow on wet grass. Unstable footing could cause
slipping.
20. Stop the blade when crossing gravel drives, walks or roads.
21. If the equipment should start to vibrate abnormally, stop
the engine and check immediately for the cause. Vibration
is generally a warning of trouble.
Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the mower
and the mowing activity. They do not understand the dangers.
Never assume that children will remain where you last saw them.
22. Shut the engine off and wait until the blade comes to
a complete stop before removing the grass catcher or
unclogging the chute. The cutting blade continues to
rotate for a few seconds after the blade control is released.
Never place any part of the body in the blade area until you
are sure the blade has stopped rotating.
1.
Keep children out of the mowing area and under watchful
care of a responsible adult other than the operator.
2.
Be alert and turn mower off if a child enters the area.
3.
Before and while moving backwards, look behind and
down for small children.
23. Never operate mower without proper trail shield,
discharge cover, grass catcher, blade control or other safety
protective devices in place and working. Never operate
mower with damaged safety devices. Failure to do so can
result in personal injury.
4.
Use extreme care when approaching blind corners,
doorways, shrubs, trees, or other objects that may obscure
your vision of a child who may run into the mower.
5.
6.
Keep children away from hot or running engines. They can
suffer burns from a hot muffler.
24. Muffler and engine become hot and can cause a burn. Do
not touch.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.
25. Never attempt to make a wheel or cutting height
adjustment while the engine is running.
26. Only use parts and accessories made for this machine by
the manufacturer. Failure to do so can result in personal
injury.
4
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t iO n pr a c t i c e s
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Check the blade and engine mounting bolts at frequent
intervals for proper tightness. Also, visually inspect blade
for damage (e.g., bent, cracked, worn) Replace blade with
the original equipment manufacture’s (O.E.M.) blade only,
listed in this manual. “Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!”
Service
Safe Handling Of Gasoline:
1.
To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive. Serious personal injury can
occur when gasoline is spilled on yourself or your clothes,
which can ignite. Wash your skin and change clothes
immediately.
4.
5.
6.
7.
Mower blades are sharp and can cut. Wrap the blade or
wear gloves, and use extra caution when servicing them.
Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
2.
Use only an approved gasoline container.
3.
Never fill containers inside a vehicle or on a truck or trailer
bed with a plastic liner. Always place containers on the
ground away from your vehicle before filling.
Never tamper with safety devices. Check their proper
operation regularly.
After striking a foreign object, stop the engine, disconnect
the spark plug wire and ground against the engine.
Thoroughly inspect the mower for any damage. Repair the
damage before starting and operating the mower.
4.
5.
Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible,
then refuel such equipment on a trailer with a portable
container, rather than from a gasoline dispenser nozzle.
8.
9.
Never attempt to make a wheel or cutting height
adjustment while the engine is running.
Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do
not use a nozzle lock-open device.
Grass catcher components, discharge cover, and trail shield
are subject to wear and damage which could expose
moving parts or allow objects to be thrown. For safety
protection, frequently check components and replace
immediately with original equipment manufacturer’s
(O.E.M.) parts only, listed in this manual. “Use of parts
which do not meet the original equipment specifications
may lead to improper performance and compromise
safety!”
6.
7.
Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
Never fuel machine indoors because flammable vapors will
accumulate in the area.
8.
Never remove gas cap or add fuel while engine is hot or
running. Allow engine to cool at least two minutes before
refueling.
9.
Never over fill fuel tank. Fill tank to no more than 1 inch
below bottom of filler neck to provide for fuel expansion.
10. Do not change the engine’s governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
10. Replace gasoline cap and tighten securely.
11. Check fuel line, tank, cap, and fittings frequently for cracks
11. If gasoline is spilled, wipe it off the engine and equipment.
Move machine to another area. Wait 5 minutes before
starting engine.
or leaks. Replace if necessary.
12. Do not crank engine with spark plug removed.
12. Never store the machine or fuel container near an open
flame, spark or pilot light as on a water heater, space
heater, furnace, clothes dryer or other gas appliances.
13. Maintain or replace safety and instruction labels, as
necessary.
14. Observe proper disposal laws and regulations. Improper
13. To reduce fire hazard, keep machine free of grass, leaves,
or other debris build-up. Clean up oil or fuel spillage and
remove any fuel soaked debris.
disposal of fluids and materials can harm the environment.
15. According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
or 140 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
14. Allow machine to cool at least 5 minutes before storing.
General Service:
1.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
2.
Before cleaning, repairing, or inspecting, make certain the
blade and all moving parts have stopped. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t iO n pr a c t i c e s
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice Regarding Emissions
Spark Arrestor
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
WARNING: This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine’s
exhaust system is equipped with a spark arrestor
meeting applicable local or state laws (if any).
If a spark arrestor is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrestor for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
6
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t iO n pr a c t i c e s
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
DANGER — ROTATING BLADES
To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover
or grass catcher is in its proper place. If damaged, replace immediately.
DANGER — BYSTANDERS
Do not mow when children or others are around.
DANGER — HAND/ FOOT CUT
Keep hands and feet away from rotating parts.
DANGER — THROWN DEBRIS
Remove objects that can be thrown by the blade in any direction. Wear safety glasses.
DANGER — SLOPES
Use extra caution on slopes. Do not mow slopes greater than 15°.
WARNING—GASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during operation. Allow engine
and muffler to cool before touching.
WARNING: Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t iO n pr a c t i c e s
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t iO n pr a c t i c e s
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly & Set-Up
3
Contents of Carton
•
•
One Lawn Mower
One Grass Catcher
•
•
One Side Discharge Chute
•
•
One Bottle of Oil
One Lawn Mower Operator’s Manual
One Engine Operator’s Manual
2.
Insert a carriage bolt found in the manual bag into the
upper hole on the handle mounting bracket. Secure with
one plastic wing nut, also included in the manual bag.
Repeat on other side with remaining hardware. See Fig. 3-2.
Assembly
NOTE: This unit is shipped without gasoline or oil in the engine.
Fill up gasoline and oil as instructed in the Engine Operation
section BEFORE operating your mower.
Handle Hardware
Carriage Bolts (2)
Handle
1.
Remove any packing material which may be between
upper and lower handles.
a. Pull up and back on upper handle as shown in Fig.
3-1. Make certain the lower handle is seated securely
into the handle mounting brackets. Do not crimp
cable while lifting the handle up.
Wing Nuts (2)
A
Figure 3-2
B
Figure 3-1
b. Tighten star knobs to secure upper handle to lower
handle. Make sure that each carriage bolt is seated
properly in the handle.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
The rope guide is attached to the right side of the upper
handle. See Fig. 3-3. Loosen the wing nut which secures the
rope guide.
b. Slip plastic channel of grass bag over hooks on the
frame. See Fig. 3-4. All the plastic channels except
center top of bag attach from outside of frame.
A
A
B
D
C
C
B
Figure 3-4
Figure 3-3
a. Hold blade control against upper handle.
c. Attach center top of bag from inside of frame.
Follow the steps below to attach the grass catcher:
a. Lift rear discharge door. See Fig. 3-5.
b. Pull starter rope out of the engine. Release blade
2.
control.
c. Slip starter rope into rope guide.
d. Tighten wing nut.
4.
Insert post on cable tie into hole provided on the lower
handle. Pull cable tie tight and trim excess.
Grass Catcher
1.
Follow steps below to assemble the grass catcher. Make
certain bag is turned right side out before assembling
(warning label will be on the outside).
B
A
a. Place bag over frame so that its black plastic side is
at the bottom.
Figure 3-5
b. Place grass catcher on the pivot rod. Let go of
discharge door so that it rests on the grass catcher.
WARNING: Never operate mower unless the hooks
on the grass catcher are firmly seated on the pivot
rod and the rear discharge door rests firmly against
top of the grass catcher.
10
se c t i O n 3 — as s e M b l y & se t -up
Download from Www.Somanuals.com. All Manuals Search And Download.
Side Discharge Chute
Your mower is shipped as a mulcher. To convert to side discharge,
make sure grass catcher is off of the unit and rear discharge door
is closed.
Adjustments
Cutting Height
Each wheel has a height adjustment lever to change the cutting
height of the mower.
1.
On the side of the mower, lift the mulching plug. See Figure
3-6.
1.
Depress height adjustment lever towards wheel.
2.
Slide lever to desired position for a change in cutting
height. See Fig. 3-7.
1
2
1
3
2
Figure 3-6
2.
Slide two hooks of side discharge chute under hinge pin on
mulching plug assembly. Lower the mulching plug. Do not
remove side mulching plug at any time, even when you are
not mulching.
Figure 3-7
3.
Release lever towards deck.
IMPORTANT: All wheels must be placed in the same
relative position. For rough or uneven lawns, move the
height adjustment lever to a higher position. This will stop
scalping of grass.
Set-Up
Gas and Oil Fill-Up
Refer to the separate engine owner’s manual for additional
engine information.
1.
Add oil provided before starting unit for the first time out
of the box.
2.
Service the engine with gasoline as instructed in the
separate engine owner’s manual.
WARNING: Use extreme care when handling
gasoline. Gasoline is extremely flammable and the
vapors are explosive. Never fuel the machine
indoors or while the engine is hot or running.
Extinguish cigarettes, cigars, pipes and other
sources of ignition.
3.
Charge battery as instructed in the Service section of this
manual (Electric Start Units).
se c t i O n 3 — as s e M b l y & se t -up
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Features
4
Blade Control
Electric Start Ignition Switch
Drive Control
Recoil Starter
Primer
Side Discharge
Chute
Mulch Plug
Cutting Height
Adjustment Levers
Figure 4-1
Mulch Plug
Blade Control
The mulch plug is used for mulching purposes. Instead of
The blade control is attached to the upper handle of the mower.
Depress and squeeze it against the upper handle to operate the
unit. Release it to stop engine and blade.
collecting the grass clippings in a grass catcher or using the
side discharge chute, some mower models have the option
of recirculating the clippings back to the lawn. This is called
mulching.
WARNING: This blade control is a safety device.
Never attempt to bypass its operations.
Side Discharge Chute
Your mower is shipped as a mulcher. To discharge the grass
clippings to the side instead, follow the instructions in the
Assembly & Set-Up section to attach the side discharge chute.
Drive Control
The drive control is located on the underside of the upper handle
and is used to engage the drive. Squeeze it against the upper
handle to engage the drive; release it to slow down or stop
mower from propelling.
WARNING: Keep hands and feet away from the
chute area on cutting deck. Refer to warning label
on the unit.
Primer
Electric Start Ignition Switch
The ignition switch is located on the left side of the handle panel.
It is used only for the electric starter.
The primer is located on the left side of the
engine, behind the air cleaner. Pressing the
primer forces fuel directly into the engine’s
carburetor to aid in starting the engine.
Recoil Starter
The recoil starter is attached to the right upper handle. Stand
behind the unit and pull the recoil starter rope to start the unit.
Cutting Height Adjustment Levers
One adjustment lever is located on each wheel and is used to
adjust the cutting height. All four levers have to be at the same
relative position to ensure a uniform cut.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
5
Starting Engine
WARNING: Be sure no one other than the operator
2
is standing near the lawn mower while starting
engine or operating mower. Never run engine
indoors or in enclosed, poorly ventilated areas.
Engine exhaust contains carbon monoxide, an
odorless and deadly gas. Keep hands, feet, hair and
loose clothing away from any moving parts on
engine and lawn mower.
1
3
1.
Push primer 3 times. Wait about two seconds between each
push. See Fig. 5-1. In temperature below 50°F, prime 5
times. After the engine is warmed up, one prime may be
needed for all temperatures.
3
2.
Standing behind the mower, squeeze and hold the blade
control against upper handle.
3.
Recoil Start: Pull the recoil starter lightly until resistance
is felt, then pull rapidly to overcome compression, prevent
kickback, and start the engine. Repeat if necessary. See Fig.
5-1.
Figure 5-1
NOTE: Do not allow the recoil starter to snap back against
the rope guide.
Electric Start: Turn ignition key to the right to start the
engine. Release the key after the engine starts. See Fig. 5-1.
Using as Mulcher
For mulching grass, remove the grass catcher and side discharge
chute from the mower. For effective mulching, do not cut wet
grass. If the grass has been allowed to grow in excess of four
inches, mulching is not recommended. Use the grass catcher to
bag clippings instead.
If engine does not start, it may be necessary to re-prime
the engine.
Stopping Engine
1.
Release blade control to stop the engine and blade.
Using Grass Catcher
You can use the grass catcher to collect clippings while you are
operating the mower.
WARNING: Wait for the blade to stop completely
before performing any work on the mower or to
remove the grass catcher.
1.
Attach grass catcher following instructions in the
“Assembly & Set-Up” section. Grass clippings will
automatically collect in bag as you run mower. Operate
mower till grass bag is full.
Using Your Lawn Mower
Be sure lawn is clear of stones, sticks, wire, or other objects
which could damage lawn mower or engine. Such objects could
be accidently thrown by the mower in any direction and cause
serious personal injury to the operator and others.
2.
Stop engine completely by releasing the blade control.
Make sure that the unit has come to a complete stop.
3.
Lift discharge door and pull grass bag up and away from
the mower to remove the bag. Dispose of the grass
clippings and reinstall the bag when complete.
1.
Once the engine is running, squeeze the drive control
against the upper handle to propel mower.
WARNING: The operation of any lawn mower can
result in foreign objects being thrown into the eyes,
which can damage your eyes severely. Always wear
safety glasses while operating the mower, or while
performing any adjustments or repairs on it.
WARNING: If you strike a foreign object, stop the
engine. Remove wire from the spark plug,
thoroughly inspect mower for any damage, and
repair damage before restarting and operating.
Extensive vibration of mower during operation is an
indication of damage. The unit should be promptly
inspected and repaired.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Adjustments
6
2.
Lubricate the wheels at least once a season with light oil (or
motor oil). If wheels are removed for any reason, lubricate
surface of the pivot arm and inner surface of the wheel
with light oil. See Fig. 6-1.
Maintenance
General Recommendations
•
•
Always observe safety rules when performing any
maintenance.
3.
Lubricate the torsion spring and pivot points on the rear
discharge door and side mulch plug periodically with light
oil to prevent rust. See Fig. 6-1.
The warranty on this lawn mower does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from warranty, operator must maintain
the lawn mower as instructed here.
4.
5.
The transmission is pre-lubricated and sealed at the factory
and does not require lubrication.
Follow the accompanying engine manual for lubrication
schedule and instruction for engine lubrication.
•
•
•
Changing of engine-governed speed will void engine
warranty.
All adjustments should be checked at least once each
season.
Deck Care
Clean underside of the mower deck after each use to prevent
build-up of grass clippings or other debris. Follow steps below
for this job.
Periodically check all fasteners and make sure these are
tight.
1.
Disconnect spark plug wire. Drain gasoline from lawn
mower or place a piece of plastic under the gas cap.
WARNING: Always stop engine, disconnect spark
plug, and ground against engine before performing
any type of maintenance on your machine.
2.
Tip mower so that it rests on the housing. Keep the side
with the air cleaner facing up. Hold mower firmly.
Lubrication
WARNING: Never tip the mower more than 90º in
any direction and do not leave the mower tipped for
any length of time. Oil can drain into the upper part
of the engine causing a starting problem.
1.
Lubricate pivot points on the blade and drive controls
at least once a season with light oil. These controls must
operate freely in both directions. See Fig. 6-1.
3.
4.
Scrape and clean the underside of the deck with a suitable
tool. Do not spray with water.
IMPORTANT: Do not use a pressure washer or garden hose
to clean your unit. These may cause damage to bearings,
or the engine. The use of water will result in shortened life
and reduce serviceability.
Put the mower back on its wheels on the ground. If you
had put plastic under the gas cap earlier, make sure to
remove it now.
Figure 6-1
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine Care
Replacing Rear Flap
A list of key engine maintenance jobs required for good
performance by the mower is given below. Follow the
accompanying engine manual for a detailed list and instructions.
1.
To remove rear flap, lift rear door, and press flap in on
either side to remove from hole. See Fig. 6-2.
•
•
Maintain oil level.
Service air cleaner every 25 hours under normal conditions.
Clean every few hours under extremely dusty conditions.
•
•
Clean spark plug and reset the gap once a season.
Clean engine regularly with a cloth or brush. Keep the area
around the top of the engine clean to permit proper air
circulation. Remove all grass, dirt, and combustible debris
from muffler area.
Figure 6-2
2.
Remove flap from opposite hole and replace with new flap
in the opposite order and manner of removal.
se c t i O n 6 — Ma i n t e n a n c e & ad j u s t M e n t s
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
7
5.
Lubricate the engine crankshaft and the inner surface of
Blade Care
the blade adapter with light oil. Slide the blade adapter
onto the engine crankshaft. Place the blade on the adapter
such that the side of the blade marked “Bottom” (or with
part number) faces the ground when the mower is in the
operating position. Make sure that the blade is aligned and
seated on the blade adapter flanges.
WARNING: When removing the cutting blade for
sharpening or replacement, protect your hands with
a pair of heavy gloves or use a heavy rag to hold the
blade.
Periodically inspect the blade adapter for cracks, especially if you
strike a foreign object. Replace when necessary. Follow the steps
below for blade service.
6.
Place blade bell support on the blade. Align notches on the
blade bell support with small holes in blade.
7.
Replace hex bolt and tighten hex bolt to torque: 450 in. lbs.
min., 600 in. lbs. max.
1.
Disconnect spark plug boot from spark plug. Turn mower
on its side making sure that the air filter and the carburetor
are facing up.
To ensure safe operation of your mower, periodically check the
blade bolt for correct torque.
2.
Remove the bolt and the blade bell support which hold the
blade and the blade adapter to the engine crankshaft. See
Fig. 7-1.
Belt Care
1.
Remove two shoulder screws securing front drive cover to
mower deck. See Figure 7-2. Press inward on sides of front
drive cover and release tabs that secure it to the height
adjuster brackets. Remove drive cover from mower.
Blade
Blade
Adapter
Blade Bell
Support
Bolt
Figure 7-1
3.
Remove blade and adapter from the crankshaft. See Fig.
7-1.
Figure 7-2
4.
Remove blade from the adapter for testing balance.
Balance the blade on a round shaft screwdriver to check.
Remove metal from the heavy side until it balances evenly.
When sharpening the blade, follow the original angle of
grind. Grind each cutting edge equally to keep the blade
balanced.
2.
Loosen screw holding belt tension spring to transmission.
See Figure 7-2 inset. Do not remove screw completely. As
you loosen it, tension on the belt will be released. Push
transmission up a little and slide belt off the transmission
pulley.
WARNING: An unbalanced blade will cause
excessive vibration when rotating at high speeds. It
may cause damage to mower and could break
causing personal injury.
3.
Tip mower on its side with the air filter up to access belt
from underside of mower and remove blade as described
in the previous section. Refer to Fig. 7-1.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Press inward on tab on the engine baffle to release it from
the baffle bracket. See Fig. 7-3.
6.
Replace with new belt, making sure belt is firmly seated on
engine pulley while pulling from the other side and sliding
it around the transmission pulley.
7.
Reattach engine baffle and reassemble blade as described
in the previous section.
8.
Turn mower back over and make sure belt is seated on
the transmission pulley. Tighten screw loosened earlier to
secure belt tension spring to the transmission.
9.
Reassemble front drive cover.
Replacing Battery
WARNING: Batteries contain sulfuric acid which
may cause burns. Do not short circuit or mutilate
batteries in any way. Do not put batteries in fire as
these may burst or release toxic materials.
1.
Loosen star knobs securing upper and lower handles and
carefully fold the upper handle down toward the lower
handle as shown in Fig. 7-5.
Figure 7-3
5.
Slide belt off of engine pulley and thread through the
opening in the deck. See Figure 7-4.
Figure 7-5
2.
Remove the two screws securing battery cover to battery
housing and place them to the side. See Fig. 7-5.
3.
Open battery cover, remove positive and negative leads
from battery, remove and replace with new battery.
Connect the positive lead to the positive side of the battery
pack, then connect the negative side.
Figure 7-4
se c t i O n 7 — se r v i c e
17
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: The battery you have may differ slightly from the
one shown in Fig. 7-6. Refer to the Parts List.
Charging Battery
WARNING: The battery contains corrosive fluid
and toxic material; handle with care and keep away
from children. Do not puncture, disassemble,
mutilate or incinerate the battery. Explosive gases
could be vented during charging or discharging. Use
in a well ventilated area, away from sources of
ignition.
Positive
Terminal
Negative
Terminal
NOTE: The special designed plug on the charger will only fit into
the plug on the battery box.
1.
Plug the battery charger into the port on the underside of
the battery housing. See Fig. 7-7.
Figure 7-6
IMPORTANT: When replacing battery pack in handle panel,
battery pack must be positioned with the positive terminal
to the left side and the negative terminal to the right side
of panel (Positive terminal is closest to the key switch).
See Fig. 7-6. Replacing battery pack incorrectly will cause
serious damage.
1
2
4.
5.
Reattach battery cover to battery housing by securing with
the two screws removed earlier, making sure to snap the
wire conduit on the left into place on the housing.
Figure 7-7
Fold handles back up and tighten star knobs.
2.
Insert the battery charger plug into a standard 120 volt
household outlet. Charge battery for 8 to 10 hours before
initial use. Do not charge longer than 12 hours.
NOTE: For optimal engine starting performance and
battery life, charge the battery after every use for 8 to 10
hours or until the green LED light illuminates (If equipped).
Do not charge longer than 12 hours.
3.
After charging, disconnect charger plug from outlet first,
then disconnect charger lead from battery.
IMPORTANT: Do not remove the battery pack from
the electric starter housing for any reason other than
replacement.
IMPORTANT: Always plug charger lead into battery pack
lead first, and then insert battery charger plug into 120
volt standard household outlet. Follow this order of action
every time you charge the battery.
18
se c t i O n 7— se r v i c e
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Fuse
Off-Season Storage
The electric starter circuit and battery are protected by a 40
ampere fuse. If the fuse burns out, the electric starter will not
operate. If the unit fails to start with the electric starter, perform
the following steps to check the fuse inside the battery housing:
The following steps should be taken to prepare your lawn mower
for storage.
•
•
•
•
•
Clean and lubricate mower thoroughly as described in the
lubrication instructions.
1.
Open the battery cover as described in Replacing Battery.
Do not use a pressure washer or garden hose to clean your
unit.
See Fig. 7-5.
2.
Remove fuse from socket and inspect as shown in Fig. 7-8.
If it is burned out, replace with standard automotive 40
ampere fuse.
Coat mower’s cutting blade with chassis grease to prevent
rusting.
Refer to the accompanying Engine Manual for correct
engine storage instructions.
Store mower in a dry, clean area. Do not store next to
corrosive materials, such as fertilizer.
When storing any type of power equipment in a poorly
ventilated or metal storage shed, care should be taken to
rust-proof the equipment. Using a light oil or silicone, coat the
equipment, especially cables and all moving parts of your lawn
mower before storage.
Battery
The battery must be stored with a full charge. Extended storage
of a discharged battery will reduce life and capacity of the
battery.
Blown Fuse
Figure 7-8
3.
Carefully place wiring back into housing, close battery
cover, and fold upper handle back into place.
NOTE: The engine can be started manually if the fuse burns
out.
se c t i O n 7 — se r v i c e
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Problem
Cause
Remedy
Engine Fails to start
1. Blade control disengaged.
1. Engage blade control.
2. Spark plug boot disconnected.
3. Fuel tank empty or stale fuel.
2. Connect wire to spark boot.
3. Fill tank with clean, fresh gasoline.
4. Engine not primed (if equipped with primer).
4. Prime engine as instructed in the Operation
section.
5. Faulty spark plug.
6. Blocked fuel line.
7. Engine flooded.
5. Clean, adjust gap, or replace.
6. Clean fuel line.
7. Wait a few minutes to restart, but do not
prime.
8. Fuel valve (if equipped) closed.
8. Open fuel valve. See engine manual.
9. Engine not choked (if equipped with choke).
9. Choke engine. See engine manual.
10. Burnt fuse. (Electric Start only)
1. Spark plug boot loose.
10. Replace fuse (see Service Section).
1. Connect and tighten spark plug boot.
Engine runs erratic
2. Blocked fuel line or stale fuel.
2. Clean fuel line; fill tank with clean, fresh
gasoline.
3. Vent in gas cap plugged.
4. Water or dirt in fuel system.
5. Dirty air cleaner.
3. Clear vent.
4. Drain fuel tank. Refill with fresh fuel.
5. Refer to engine manual.
6. Push CHOKE knob in.
6. Unit running with CHOKE (if equipped)
applied.
Engine overheats
1. Engine oil level low.
2. Air flow restricted.
1. Fill crankcase with proper oil.
2. Clean area around and on top of engine.
1. Adjust gap to .030”.
Occasional skips
(hesitates) at
high speed
1. Spark plug gap too close.
Idles poorly
1. Spark plug fouled, faulty, or gap too wide.
2. Dirty air cleaner.
1. Reset gap to .030” or replace spark plug.
2. Refer to engine manual.
Excessive Vibration
1. Cutting blade loose or unbalanced.
2. Bent cutting blade.
1. Tighten blade and adapter. Balance blade.
2. See an authorized service dealer.
Mower will not
mulch grass
1. Wet grass.
1. Do not mow when grass is wet; wait until
later to cut.
2. Excessively high grass.
2. Mow once at a high cutting height, then
mow again at desired height or make a
narrower cutting path.
3. Dull blade.
3. Sharpen or replace blade.
Continued on next page
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Cause
Remedy
Uneven cut
1. Wheels not positioned correctly.
1. Place all four wheels in same height position
(if equipped with individual height adjusters).
2. Dull blade.
2. Sharpen or replace blade.
Mower will not self propel
1. Belt not installed properly.
1. Check belt for proper pulley installation and
movement.
2. Debris clogging drive operation.
2. Stop engine, disconnect spark plug boot,
and clean out debris.
3. Damaged or worn belt.
3. Inspect and replace belt.
se c t i O n 8 — tr O u b l e s h O O t in g
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts
9
Component
Part Number and Description
951-10292
Spark Plug
951-10298
Air Cleaner Kit
951-10300
951-10358
Fuel Cap Assembly
Fuel Filter
734-04223A
734-04226A
Wheel (Front)
Wheel (Rear)
731-04177
942-0741A
Discharge Chute
Mulching Blade
Phone (800) 965-4CUB or 877-282-8684 for your nearest Cub Cadet Dealer to order replacement parts or a complete Parts Manual
com
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Component
Part Number and Description
964-04054
Grass Bag
954-0637A
725-04329
Belt
Battery Charger
925-04323
925-0201
Battery
Key
Phone (800) 965-4CUB or 877-282-8684 for your nearest Cub Cadet Dealer to order replacement parts or a complete Parts Manual
com
Se c t i o n 9 — Re p l a c e m e n t pa R t S
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR
WALk-BEhIND MOWERS
IMPORTANT: To obtain warranty coverage owner must present an
Without limiting the foregoing, this limited warranty does not provide
coverage in the following cases:
original proof of purchase and applicable maintenance records to the
servicing dealer. Please see the operator’s manual for information on
required maintenance and service intervals.
a. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments, deck
adjustments, and normal deterioration of the exterior finish due to
use or exposure.
The limited warranty set forth below is given by Cub Cadet LLC with
respect to new merchandise purchased or leased and used in the United
States and/or its territories and possessions, and by MTD Products
Limited with respect to new merchandise purchased or leased and
used in Canada and/or its territories and possessions (either entity
respectively, “Cub Cadet”).
b. Service completed by someone other than an authorized service
dealer.
c. Cub Cadet does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and their
respective possessions and territories, except those sold through
Cub Cadet’s authorized channels of export distribution.
Cub Cadet warrants this product (excluding its Normal Wear Parts
and Batteries, as described below) against defects in material and
workmanship for a period of three (3) years, commencing on the date
of original retail purchase or lease and will, at its option, repair or
replace, free of charge, any part found to be defective in materials or
workmanship.
d. Replacement parts and\or accessories that are not genuine Cub
Cadet parts.
e. Transportation charges and service calls.
Normal Wear Parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of original
purchase or lease. Normal wear parts include, but are not limited to
items such as: belts, blades, blade adapters, grass bags, engine oil, air
filters, spark plugs and wheels.
f. Cub Cadet does not warrant this product for commercial use.
There are no implied warranties, including without limitation any
implied warranty of merchantability or fitness for a particular
purpose. No warranties shall apply after the applicable period of
express written warranty above. No other express warranties beyond
those mentioned above, given by any person or entity, including a
dealer or retailer, with respect to any product, shall bind Cub Cadet.
The exclusive remedy is repair or replacement of the product as
set forth above. The terms of this warranty provide the sole and
exclusive remedy arising from the sale and/or lease of the products
covered hereby. Cub Cadet shall not be liable for any incidental or
consequential loss or damage including, without limitation, expenses
incurred for substitute or replacement lawn care services or for rental
expenses to temporarily replace a warranted product.
Batteries have a one-year prorated limited warranty against defects in
material and workmanship, with 100% replacement during the first three
months. After three months, the battery replacement credit is based on
the months remaining in the twelve (12) month period dating back to the
original date of original sale or lease. Any replacement battery will be
warranted only for the remainder of the original warranty period.
This limited warranty shall only apply if this product has been operated
and maintained in accordance with the Operator’s Manual furnished with
the product, and has not been subject to misuse, abuse, commercial
use, neglect, accident, improper maintenance, alteration, vandalism,
theft, fire, water, or damage because of other peril or natural disaster.
Damage resulting from the installation or use of any part, accessory
or attachment not approved by Cub Cadet for use with the product(s)
covered by this manual will void your warranty as to any resulting
damage. In addition, Cub Cadet may deny warranty coverage if the
hour meter, or any part thereof, is altered, modified, disconnected or
otherwise tampered with.
Some jurisdictions do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply to
you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and
their property arising out of the misuse or inability to use the product.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF
OF PURCHASE AND APPLICABLE MAINTENANCE RECORDS, through
your local authorized service dealer. To locate the dealer in your area:
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
In the U.S.A.:
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited warranty
gives you specific legal rights, and you may also have other rights that
vary in different jurisdictions.
Check your Yellow Pages, or contact Cub Cadet LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, call 1-877-282- 8684
In Canada:
Contact MTD Products Limited, Kitchener, ON N2G 4J1, call 1-800-668-
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OhIO 44136-0019, Phone: 1-877-282-8684
MTD Products Limited, kitchener, ON N2G 4J1, Phone: 1-800-668-1238
GDOC-100088 REV. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|