Installation Instructions
759-04080 CRUISE CONTROL KIT
For Series 6000 Tractor Models
KIT COMPONENTS
3
5
2
6
1
7
Ref. Pt. No.
Description
1. 1750736
2. 1768971
3. 703-05791
4. 712-0240
5. 725-0157
6. 725-04246
7. 736-0171
Special Screw
Magnet w/Spring Assy.
Cruise Latch Bracket
Hex Jam Nut, 7/16-20
Cable Tie
Cruise Switch
Lock Washer, 7/16"
4
Introduction
NOTE: The wire harness connector for the cruise switch
may be connected to the dash panel plug. If so, carefully
pull the wire harness connector up through the dash
panel while removing the plug. If the wire harness leads
are not connected to the plug, it will be necessary to re-
move the dash panel insert.
The cruise control kit is designed to allow the tractor op-
erator to maintain a desired “foot free” forward speed
in areas where constant speed changes are not re-
quired. The cruise control feature can only be operated
in the forward direction.
Installing the Cruise Control Kit
NOTE: Some installation procedures are more easily
performed from beneath the tractor. If equipped, the
mower deck may be removed from the tractor to im-
prove access.
Remove
Plug
Wire leads w/connectors needed to power the cruise
control magnet are provided in the tractor wire harness.
To install the cruise control kit, proceed as follows:
• Remove the plug from the right side of the dash
panel by sliding a thin flat edged tool beneath the
plug and prying upward. See Figure 1.
Figure 1
CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A.
FORM NO. 769-01718 (3/05)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
• Insert the cruise latch bracket (Ref. 3) down
through the opening in the fender/running board so
that its large plate area is against the left side of
the magnet. See Figure 8.
Lock Washer
Special Screw
Spring
Tractor
Frame
Hex
Jam
Nut
Hex Tapp
Screw
Cruise
Latch
Bracket
Pedal Shaft Plate
Drive Shaft Shield
Figure 6
• Slide the lock washer (Ref.7) onto the special
screw, then thread the hex jam nut (Ref.4) onto the
screw. Refer to Figure 6.
Magnet
NOTE: Because of limited space between the ped-
al shaft plate and frame, it may be easier to install
the hex jam nut from the underside of the tractor.
Figure 8
• Pivot the rear of the cruise latch bracket downward
so that the bracket mounting holes align with the
holes of the drive shaft shield. Refer to Figure 8.
• Fully tighten the hex jam nut onto the special
screw. Then from beneath the right running board
carefully retighten the hex lock nut to reposition the
pedal shaft. Refer to Figure 5.
• While holding the cruise latch bracket tightly
against the magnet, secure the bracket with the
two hex tapp screws removed earlier. Refer to Fig-
ure 8.
• Hook the bent tab of the magnet (Ref. 2) into the
square hole of the pedal shaft plate and pivot the
magnet onto the special screw (See Figure 7).
Push the magnet onto the screw so that the bent
tab is behind the plate and retains the magnet on
the screw.
• Locate the unused two wire connector of the main
wire harness along the right side of the frame (See
Figure 9). Plug the two wires from the magnet into
the wire harness connector.
Magnet
Drive Shaft
Bent Tab
Main Harness
Hook tab &
pivot onto
screw
Square
Hole
Wire Harness
Connector
Figure 9
Figure 7
• Use the cable tie (Ref.5) to secure the wire har-
ness lead and magnet wires to the main harness,
away from the drive shaft. Refer to Figure 9.
• Remove the two hex tapp screws securing the
right side of the tractor drive shaft shield to the
frame. Refer to Figure 8.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting The Cruise Control
WARNING: Always use extreme caution
Disengaging the Cruise Control
NOTE: Regardless of the method used, the indicator
light in the cruise switch will turn off when the cruise
control is disengaged. Simply depress the top of the
switch to re-engage the cruise control.
when operating the tractor with the
cruise control engaged. Use good judge-
ment and maintain a safe speed for the
conditions of operation.
Disengage the cruise control using one of the following
methods:
• Depress the brake pedal to disengage the cruise
control and stop the tractor.
NOTE: The cruise control feature can only be operat-
ed in the forward direction.
• Slowly depress the forward control pedal until the
desired speed is achieved.
• Depress the bottom of the cruise control switch to
disengage the cruise control.
• While holding the forward control pedal, depress
the top of cruise control switch to energize the
magnet and engage the cruise control. NOTE: The
light of the switch will illuminate to indicate the
switch has been depressed to the "ON" position.
NOTE: Although not recommended, depressing the
forward/reverse pedal to the reverse position will also
disengage the cruise control.
To change to the reverse direction when operating with
cruise control, use one of the recommended methods
to disengage the cruise control, then depress the re-
verse control pedal.
• If the cruise control has engaged, the forward con-
trol pedal will lock in the desired position, and the
tractor will maintain the same forward speed when
you remove your foot from the pedal.
• If you wish to increase the speed while the cruise
control is engaged, simply depress the forward
pedal further. It is not necessary to disengage and
re-engage the cruise control.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|