®
BUSH HOG
RFM 60
Rear Finishing Mower
Operator’s Manual
l
l
ASSEMBLY OPERATION MAINTENANCE
04/09 Rev. 1
$4.00
50050226
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM 60
Operator’s Manual
TABLE OF CONTENTS
SECTION/PARA
PAGE
SECTION/PARA
PAGE
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .2
Dealer Preparation Check List . . . . . . . . .3
Safety Precautions . . . . . . . . . . . . . . . . . .4
Federal Laws and Regulations . . . . . . . . .6
3-3 Operation . . . . . . . . . . . . . . . . . . . . . .10
3-4 Transporting . . . . . . . . . . . . . . . . . . . .10
IV MAINTENANCE . . . . . . . . . . . . . . . . . . . .11
4-1 Maintenance Check List . . . . . . . . . .11
4-2 Lubrication . . . . . . . . . . . . . . . . . . . . .11
4-3 Belt Adjustment . . . . . . . . . . . . . . . . .12
4-4 Belt Replacement . . . . . . . . . . . . . . .12
4-5 Blade Replacement . . . . . . . . . . . . . .13
4-6 Troubleshooting . . . . . . . . . . . . . . . . .13
I
INTRODUCTION AND DESCRIPTION . .7
1-1 Introduction . . . . . . . . . . . . . . . . . . . . .7
1-2 Description . . . . . . . . . . . . . . . . . . . . .7
II PREPARATION FOR USE . . . . . . . . . . . .8
2-1 Attaching to Tractor . . . . . . . . . . . . . . .8
V DEALER ASSEMBLY . . . . . . . . . . . . . . .14
5-1 Base Unit Assembly . . . . . . . . . . . . . .14
Safety Decals . . . . . . . . . . . . . . . . . . . . . .16
III OPERATING INSTRUCTIONS . . . . . . . .10
3-1 General Safety . . . . . . . . . . . . . . . . .10
3-2 Cutting Height Adjustment . . . . . . . . .10
Torque Specifications . . . . . . . . . . . . . . .17
RETAIL CUSTOMER’S RESPONSIBILITY
UNDER THE BUSH HOG WARRANTY
It is the Retail Customer and/or Operator’s responsibility to read the Operator’s
Manual, to operate, lubricate, maintain and store the product in accordance with all
instructions and safety procedures. Failure of the operator to read the Operator’s
Manual is a misuse of this equipment.
It is the Retail Customer and/or Operator’s responsibility to inspect the product and to
have any part(s) repaired or replaced when continued operation would cause damage
or excessive wear to other parts or cause a safety hazard.
It is the Retail Customer’s responsibility to deliver the product to the authorized Bush
Hog Dealer, from whom he purchased it, for service or replacement of defective parts
which are covered by warranty. Repairs to be submitted for warranty consideration
must be made within forty-five (45) days of failure.
It is the Retail Customer’s responsibility for any cost incurred by the Dealer for travel-
ing to or hauling of the product for the purpose of performing a warranty obligation or
inspection.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an
authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period
of one (1) year for non-commercial, state and municipalities’ use and ninety (90) days for commercial use from
date of retail sale. Model RFM gearboxes are covered by a five (5) year limited warranty period. The obligation
of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts.
Replacement or repair parts installed in the equipment covered by this limited warranty are warranted
for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equip-
ment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an
authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equip-
ment or parts which are claimed to have been defective in material or workmanship.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES
Bush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all war-
ranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to
the sale or use of the items warranted. Such incidental and consequential damages shall include but not be
limited to: transportation charges other than normal freight charges; cost of installation other than cost
approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss
of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of
equipment or parts resulting from acts beyond the control of Bush Hog.
THIS LIMITED WARRANTY SHALL NOT APPLY:
1. To vendor items which carry their own warranties, such as engines, tires, and tubes.
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.
3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judge-
ment of Bush Hog such use affects its performance, stability or reliability.
4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner
which, in the sole judgement of Bush Hog, affects its performance, stability or reliability.
5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid,
worn blades, or to normal deterioration of such things as belts and exterior finish due to use or
exposure.
6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the
company’s sole judgement is a wear item.
NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED
WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE I
N
WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA
36703.
OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
MODEL NUMBER
Record the model number, serial number and date
purchased. This information will be helpful to your
dealer if parts or service are required.
SERIAL NUMBER
MAKE CERTAIN THE WARRANTY INFORMATION
HAS BEEN FILED ONLINE WITH BUSH HOG
DATE OF RETAIL SALE
SELMA, ALABAMA
.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
DEALER PREPARATION CHECK LIST
RFM 60 Finishing Mowers
BEFORE DELIVERING MACHINE — The following check list should be completed.
Use the Operator’s Manual as a guide.
r 1. Assembled completed.
r 2. Gearboxes filled with oil.
r 3. All fittings lubricated.
r 4. All shields in place and in good condition.
r 5. All fasteners torqued to specifications given in Torque Chart
r 6. All decals in place and readable. (See decal page.)
r 7. Overall condition good (i.e. paint, welds)
r 8. Operators manual has been delivered to owner and he has been instructed
on the safe and proper use of the cutter.
r 9. Warranty information has been registered online with Bush Hog.
Dealer’s
Signature
Purchaser’s
Signature
THIS CHECKLIST TO REMAIN IN OWNER’S MANUAL
It is the responsibility of the dealer to complete the procedures listed
above before delivery of this implement to the customer.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Alert Symbol
This Safety Alert Symbol means: “ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!”
This symbol is used to call attention to safety
precautions that should be followed by the
operator to avoid accidents. When you see this
symbol, carefully read the message that follows
and heed its advice. Failure to comply with
safety precautions could result in death or seri-
ous bodily injury.
Safety Signs Signal Words
The signal words DANGER, WARNING, AND CAUTION are used on the equipment safety signs. These words
are intended to alert the viewer to the existence and the degree of hazard seriousness.
This signal word indicates a potentially hazardous situation
which, if not avoided, will result in death or serious injury.
White letters on RED
This signal word indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury
It may also be used to alert against unsafe practices.
Black letters on ORANGE
This signal word indicates a potentially hazardous situation exist
which, if not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices.
Black letters on YELLOW
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY PRECAUTIONS
This symbol is used to call attention to safety
precautions that should be followed by the
operator to avoid accidents. When you see this
symbol, carefully read the message that fol-
lows and heed its advice. Failure to comply
with safety precautions could result in death or
serious bodily injury.
In addition to the design and configuration of equipment, hazard control and accident prevention are depen-
dent upon the awareness, concern, prudence and proper training of personnel in the operation, transport,
maintenance and storage of equipment. Lack of attention to safety can result in accident, personal injury,
reduction of efficiency and worst of all—loss of life. Watch for safety hazards and correct deficiencies
promptly. Use the following safety precautions as a general guide to safe operations when using this
machine. Additional safety precautions are used throughout this manual for specific operating and mainte-
nance procedures. Read this manual and review the safety precautions often until you know the limitations.
1. Read the Operator’s Manual. Failure to read the Operator’s Manual is considered a misuse of this
equipment.
2. Become familiar with all the machine’s controls and all the caution, warning and danger decals affixed
to the machine before attempting to start or operate.
3. Before starting or operating the machine, make a walk around inspection and check for obvious
defects such as loose mounting bolts and damaged components. Correct any deficiency before
starting.
4. Do not allow children to operate the cutter. Do not allow adults to operate it without proper instruction.
5. Do not carry passengers.
6. Keep the area of operation clear of all persons, particularly small children and pets. The operator
should cease mowing whenever anyone comes within the operating area.
7. Clear the work area of objects which might be picked up and thrown.
8. Use a piece of cardboard or wood rather than hands to search for hydraulic leaks. Escaping hydraulic
oil under pressure can penetrate skin. If fluid is injected into the skin, it must be surgically removed
within a few hours by a doctor familiar with this form of injury or gangrene may result.
9. Do not operate without all guards and shields in place and in good condition.
10. Lower implement to ground, stop tractor engine, apply parking brake, and allow blades to completely
stop before leaving the tractor.
11. Keep hands and feet away from blades.
12. This cutter is not to be operated along highways or in any area where people may be present unless
all sides of the unit are enclosed by permanent bands, safety chains or other factory approved safety
shields that are in good repair.
13. Wear personal protective equipment such as, but not limited to, protection for eyes, ears, feet, hands
and head when operating or repairing the equipment. Do not wear loose clothing or jewelry that may
catch on equipment moving parts.
14. When performing adjustments or maintenance on the cutter, first lower it to the ground or block it
securely at a workable height.
15. Never stand between tractor and cutter while tractor is being backed to the cutter hitch.
16. Reduce speed when transporting cutter to avoid bouncing and momentary loss of steering.
17. Use tractor flashing warning lights, day or night, when transporting cutter on road or highways unless
prohibited by law.
18. It is recommended that tractor be equipped with Rollover Protective System (ROPS) and seat belt be
used in all mowing operations.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING
EMPLOYERS, EMPLOYEES AND OPERATIONS.
*(This section is intended to explain in broad terms the concept and effect of the following federal laws and
regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA
This Act Seeks:
“...to assure so far as possible every working man and woman in the nation safe and healthful working
conditions and to preserve our human resources...”
DUTIES
Sec. 5 (a) Each employer—
(1) shall furnish to each of his employees employment and a place of employment
which are free from recognized hazards that are causing or are likely to cause
death or serious physical harm to his employees;
(2) shall comply with occupational safety and health standards promulgated under
this Act.
(b) Each employee shall comply with occupational safety and health standards
and all rules, regulations and orders issued pursuant to this Act which are
applicable to his own actions and conduct.
OSHA Regulations
Current OSHA regulations state in part: “At the time of initial assignment and at least annually thereafter, the
employer shall instruct every employee in the safe operation and servicing of all equipment with which the
employee is, or will be involved.” These will include (but are not limited to) instructions to:
Keep all guards in place when the machine is in operation;
Permit no riders on equipment;
Stop engine, disconnect the power source, and wait for all machine movement to stop before
servicing, adjusting, cleaning or unclogging the equipment, except where the machine must be
running to be properly serviced or maintained, in which case the employer shall instruct employees
as to all steps and procedures which are necessary to safely service or maintain the equipment.
Make sure everyone is clear of machinery before starting the engine, engaging power, or operating
the machine.
EMPLOYEE TRACTOR OPERATING INSTRUCTIONS:
1. Securely fasten your seat belt if the tractor has a
ROPS.
5. Watch where you are going, especially at row
ends, on roads, and around trees.
2. Where possible, avoid operating the tractor near
ditches, embankments, and holes.
6. Do not permit others to ride.
7. Operate the tractor smoothly - no jerky turns,
starts, or stops.
3. Reduce speed when turning, crossing slopes, and
on rough, slick, or muddy surfaces.
8. Hitch only to the drawbar and hitch points recom-
mended by tractor manufacturers.
4. Stay off slopes too steep for safe operation.
9. When tractor is stopped, set brakes securely and
use park lock if available.
Child Labor Under 16 Years Old
Some regulations specify that no one under the age of 16 may operate power machinery. It is your
responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of
Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION I
INTRODUCTION AND DESCRIPTION
suction during operation to lift the grass before cut-
1-1 INTRODUCTION
ting it. The four caster wheel arrangement, along
with the floating top lift linkage work together to give
an even cut and minimize scalping.
We are pleased to have you as a Bush Hog cus-
tomer. Your RFM Rotary Cutter has been carefully
designed to give maximum service with minimum
down time.This manual is provided to give you the
necessary operating and maintenance instructions
for keeping your rotary cutter in top operating condi-
tion. Please read this manual thoroughly.
Understand what each control is for and how to use
it. Observe all safety precautions decaled on the
machine and noted throughout the manual for safe
operation of implement. If any assistance or addi-
tional information is needed, contact your authorized
Bush Hog dealer.
Power from the tractor is transmitted through a trian-
gular, telescoping driveline to the 90 degree gear-
box. It is then passed to the spindle housings and
blades by a single, B-section, Kevlar reinforced belt.
Drivetrain protection is provided by belt slippage.
Table 1-1 RFM Specifications
RFM 60
NOTE
Cutting Width (in.)
Cutting Height (in.)
Horsepower Range
Blade Tip Speed (fpm)
Weight (lbs.)
60
1-1/2 to 6-1/2
14 - 30
All references made to right, left, top,
bottom, front or rear are as viewed
facing the direction of travel with
implement properly attached to trac-
tor.
18,500
450
1-2 DESCRIPTION
The RFM cutters (Figure 1-1) are intended for cut-
ting lawns or any maintained area where a clean,
uniform finish is desired. Parallel uplift blades form a
Figure 1-1 RFM 60
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION II
PREPARATION FOR USE
NOTE
2-1 ATTACHING TO TRACTOR
Due to the many variations in trac-
tor/implement hitch points and corre-
sponding differences in distances between
tractor PTO shafts and implement input
shafts, drivelines may need to be short-
ened as described in the following steps:
WARNING
NEVER STAND BETWEEN TRACTOR
AND CUTTER WHILE TRACTOR IS
BEING BACKED TO HITCH.
WARNING
B. Raise and lower cutter to determine position
with shortest distance between the tractor PTO shaft
and gearbox input shaft. Shut down tractor leaving
cutter in position of shortest distance. SECURELY
BLOCK CUTTER IN POSITION.
C. Pull driveline apart. Attach outer (female) sec-
tion to tractor PTO shaft. Pull on driveline section to
be sure yoke locks into place.
D. Hold driveline sections parallel to each other to
determine if too long. Each section should end
approximately 3 inches (76mm) short of reaching
universal joint shield on opposite section. If too long,
measure 3 inches (76mm) back from universal joint
shield and mark opposite section. (Figure 2-1). Do
this for both sections.
ADDITIONAL
TRACTOR
FRONT
BALLAST MAY BE NEEDED FOR
STABLE OPERATION AND TRANSPORT
OF CUTTER. SEE TRACTOR OPERA-
TOR’S MANUAL FOR RECOMMENDED
WEIGHTS. IT IS RECOMMENDED THAT
TRACTOR BE EQUIPPED WITH
ROLLOVER PROTECTIVE SYSTEM
(ROPS) AND SEAT BELTS.
A. Attach to tractor Cat. I three point hitch as
described in tractor operator’s manual.
E. Raise and lower cutter to determine position
with greatest distance between PTO shaft and gear-
box input shaft. Shut down tractor leaving cutter in
position of greatest distance. SECURELY BLOCK
CUTTER IN POSITION.
F. Hold down driveline sections parallel to each
other and check for minimum 6 inches (152mm)
overlap. (Figure 2-2) If driveline has been marked for
cutting, overlap will be the distance between two
marks. If driveline has less than minimum overlap,
DO NOT USE. Contact authorized Bush Hog dealer.
NOTE
If driveline is correct length, omit the fol-
lowing steps “G” through “J” and proceed
to step “K”.
Figure 2-1
Figure 2-2
Minimum
Overlap
8
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Clamp end of driveline in a vice. Cut off shield
where marked. (Figure 2-3).
Figure 2-5
Figure 2-3
DANGER
MAKE CERTAIN DRIVELINE YOKES
ARE SECURELY FASTENED. FAILURE
TO DO SO MAY RESULT IN SERIOUS
INJURY.
H. Using cut off section of shield as a guide, cut
shaft the same amount. (Figure 2-4)
Figure 2-4
L. Raise cutter off ground and adjust lower lift
arms to level cutter right to left. Refer to tractor oper-
ator’s manual.
M. Lower cutter to work position. Adjust tractor
top link to position cutter top flex link as shown in
Figure 2-6. This allows cutter to “float” during opera-
tion.
N. Adjust tractor sway chains, stabilizer bar or
equivalent to prevent side sway.
Figure 2-6 Flex-Link
Tractor
Top Link
I. Repeat steps “G” and “H” to other driveline sec-
tion.
J. Deburr ends of driveline sections and clean
away all chips and filings. (Figure 2-5)
Tractor
Lower Lift Arm
K. Apply multi-purpose grease to outside of male
driveline section. Assemble driveline and install on
tractor and cutter. Pull on each driveline section to
be sure yokes lock into place. Make certain driveline
shielding is in place and in good condition.
Lower
Link
These bolts should be tightened
“snug”, but loose enough to allow the
link to pivot.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION III
OPERATING INSTRUCTIONS
Figure 3-1
3-1 GENERAL SAFETY
Only qualified people familiar with this operator’s
manual and tractor operator’s manual should oper-
ate this machine. Operator should wear hard hat,
safety glasses and safety shoes. The operator
should read, understand and practice all safety mes-
sages shown on the caution, warning and danger
decals affixed to the cutter to avoid serious injury or
death. Use ROPS (Rollover Protective Structures)
and seat belt equipped tractors for mowing opera-
tions. Before beginning operation, clear work area of
any objects that may be picked up and thrown.
Check for ditches, stumps, holes or other obstacles
that could upset tractor or damage cutter. Always
lower cutter to ground and allow blades to come to a
complete stop, set parking brake and turn off tractor
engine before leaving tractor operator’s seat.
Spacers
Caster
Wheel
DANGER
STAY CLEAR OF ROTATING DRIVELINE. DO
NOT OPERATE WITHOUT DRIVELINE SHIELDS
IN PLACE AND IN GOOD CONDITION. FAILURE
TO HEED THESE WARNINGS MAY RESULT IN
PERSONAL INJURY OR DEATH.
3-2 CUTTING HEIGHT ADJUSTMENT
The cutter should be operated at the highest position
that will give desired cutting results. This will help pre-
vent blades from striking the ground, reducing blade
wear and undue strain on the machine. Cutting too
much material will leave excess clippings on the lawn
surface. The more frequently the lawn is mowed, the
better the effect will be. Adjust as follows:
DANGER
STAND CLEAR OF ROTATING CUTTER
BLADES UNTIL ALL MOTION HAS STOPPED.
TO AVOID ACCIDENTAL FALL AND POSSIBLE
INJURY FROM CUTTER, USE ROPS
(ROLLOVER PROTECTION STRUCTURES) AND
SEAT BELT EQUIPPED TRACTORS FOR ALL
MOWING OPERATIONS.
A. Raise cutter off ground using tractor 3-point
lift. SECURELY BLOCK CUTTER IN POSITION.
WARNING
C. With tractor at idle speed, engage PTO drive.
Advance throttle to 540 PTO rpm.
D. Place tractor in low gear and begin cutting.
Tractor forward speed should be controlled by gear
selection, not engine speed. For maximum cutting
efficiency, forward speed should allow cutter to
maintain a constant maximum blade speed.
THE CUTTER CAN FALL FROM
HYDRAULIC SYSTEM FAILURE. TO
AVOID SERIOUS INJURY OR DEATH,
SECURELY SUPPORT CUTTER BEFORE
WORKING UNDERNEATH
B. Remove pin securing caster wheel to bracket.
(Figure 3-1) Remove caster wheel from arm.
C. Place amount of spacers on caster wheel to
give desired cutting height. With no spacers on the
bottom, a 1-1/2” or slightly lower cutting height is
given.
D. Reinstall caster wheel into caster arm. Place
remaining spacers on caster wheel and install pin to
retain.
Cutting height should not put undue strain on tractor
and implement drivetrain. If tractor engine or cutter
stalls, do not slip tractor clutch to allow engine to
retain speed as this will exert undue strain on the
implement drivetrain. When stalling occurs, disen-
gage PTO drive, move to a cut area, set tractor
throttle to idle, then re-engage PTO drive.
E. Repeat operation for all caster wheels. Make
certain all wheels are adjusted to the same height.
Always cut up and down the face of slopes, never
across.
Check belt tension after first 8 hours. Adjust per-
paragraph 4-3 if needed.
3-3 OPERATION
A. Perform BEFORE EACH USE maintenance
list in paragraph 4-1.
3-4 TRANSPORTING
B. Start tractor. Lower cutter until it is supported
by caster wheels. Position tractor lower lift arms as
shown in Figure 2-6, page 9. This will allow cutter
to”float” during operation.
Turn off PTO drive and fully raise tractor 3-point lift
before transporting. When implement is transported
on road or highway, day or night, use tractor flashing
warning lights unless prohibited by law. A slow mov-
ing vehicle (SMV) sign on the tractor must be visible
from the rear by approaching vehicles.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION IV
MAINTENANCE
8.During operation, listen for abnormal sounds
4-1 MAINTENANCE CHECK LIST
which might indicate loose parts, damaged bearings,
or other damage. Correct any deficiency before con-
tinuing operation.
Perform scheduled maintenance as outlined below.
Lower implement to ground, turn off tractor, and set
parking brake before doing maintenance inspections
or work. Some checks may require raising machine
off ground and supporting with blocks. All bolts
should be torqued as indicated in torque chart
unless otherwise indicated.
AFTER EACH USE
1. Clean all debris from machine especially under-
side of deck, underneath belt shield and off safety
decals. Replace any missing or illegible decals.
2. Inspect cutter for worn or damaged compo-
nents. Repair or replace before next use. Any
replacement components installed during repair shall
include the components’ current safety decals speci-
fied by the manufacturer to be affixed to the compo-
nent.
WARNING
THE CUTTER CAN FALL FROM
HYDRAULIC SYSTEM FAILURE. TO
AVOID SERIOUS INJURY OR DEATH,
SECURELY SUPPORT CUTTER BEFORE
WORKING UNDERNEATH.
3. Store cutter in a dry place.
40 HOURS
BEFORE EACH USE.
1. Check belt for proper tension. Refer to para-
graph 4-3.
4-2 LUBRICATION (Figures 4-1A, & B)
1. Check tractor tire air pressure. Refer to tractor
operator’s manual. Check mower tire pressure (if
pneumatic tires). Tire pressure should be 30 psi.
2. Check blades and spindles to be sure that no
foreign objects such as wire or steel strapping bands
are wrapped around them.
NOTE
The multi-purpose grease referenced in this
secftion is an NLGI Grade 2 type grease.
3. Check blade bolts for tightness. Tighten blade
bolts to 76 ft./lbs.
BEFORE EACH USE
1. Driveline Universal Joints - Apply multi-purpose
grease with grease gun.
2. Driveline Guard - Apply 2-3 shots of multi-pur-
pose grease with grease gun to plastic fitting.
3. Wheels - Apply multi-purpose grease wiith
grease gun.
4. Caster Pivot - Apply multi-purpose grease with
grease gun.
5. Input Gearbox - Add EP80W-90 gear oil, if
necessary, to bring oil level to check plug.
20 HOURS
6. Driveline - Disconnect PTO driveline, pull the
two sections apart, thoroughly clean old grease from
tubes and apply thin coat of multi-purpose grease to
outside of inner (male) section. Reassemble sec-
tions and install. Pull each section to be sure drive-
line and shields are securely connected. Make cer-
tain PTO shielding is in good condition.
4. Inspect blades for wear. Replace if necessary
per paragraph 4-5. Use only genuine Bush Hog
replacement parts. If it is necessary to sharpen the
blades, remove the blades from the spindles before
sharpening. DO NOT sharpen blades while still
attached to mower.
5. Make certain all shields are in place and in
good condition. Repair or replace any missing or
damaged shields.
6. Inspect wheel(s) for wear, damage or foreign
objects. Repair or replace if necessary.
7. Perform BEFORE EACH USE lubrication per
paragraph 4-2.
Figure 4-1A
(5) Before Each Use
(6) 20 Hours
Figure 4-1B
(3) Before Each Use
(2) Before Each Use
(1) Before Each Use
(4) Before Each Use
11
Download from Www.Somanuals.com. All Manuals Search And Download.
40 HOURS
increasing or decreasing the length of the spring on
the moveable idler. For proper belt tension on the
mower, the spring length should be 6-3/4” (Figures 4-2 &
4-3) To adjust the spring length, loosen or tighten the
5/16” hex nut on the spring adjustment rod until the cor-
rect spring length is reached.
7. Spindle Assembly - Apply 3 shots of multi-
purpose grease with grease gun every 40 hours.
Grease fittings for spindles are accessible
through holes in the shields.
4-3 BELT ADJUSTMENT
4-4 BELT REPLACEMENT
Belt tensions should be checked every 40 hours to
get maximum life from drive belts and best perfor-
mance from the cutter. Belt tension is adjusted by
Use only genuine Bush Hog replacement parts.
A. Remove right and left side shields.
B. Relieve spring tension by loosening the 5/16”
hex nut on the spring adjustment rod. (Figure 4-3)
C. Remove old belt.
Figure 4-2 5/16” Hex Nuts - Spring Length Adjustment
D. Install new belt as shown below. (Also refer to
the decal on underside of belt shield) Be sure that
the belt is properly positioned in all sheave grooves.
E. Adjust tension on the belt by adjusting the
length of the spring on the moveable idler. The cor-
rect initial rod length is 1-13/16”.
F. Replace all shields before operating machine.
(7) 40 Hours
Rod Extends 1-13/16” From Frame
Figure 4-3
RFM 60 BELT DIAGRAM
FRONT
5/16” Spring Tension Adjustment Nut
1-13/16”
6-3/4”
(From Inside of Hook to Inside of Hook)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-4 Blade Placement
Spindle Assembly
4-5 BLADE REPLACEMENT
CAUTION
WEAR HEAVY WORK GLOVES TO PRO-
TECT HANDS FROM SHARP EDGES.
A. Raise cutter using tractor 3-point lift and
SECURELY BLOCK INTO POSITION.
B. Turn off tractor, set parking brake and remove
key.
C. Remove bolt and cup washer securing blade
to spindle. Remove blade.
Blade
D. Install new blade as shown in Figure 4-4 with
concave side of cup washer against blade. Be sure
that blades are installed with offset in proper direc-
tion. Tighten retaining bolt to 76 ft./lbs.
Cup Washer
Retaining Bolt
4-6 TROUBLESHOOTING
Troubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement parts
are necessary, contact your authorized Bush Hog dealer. Please have ready your machine name, model num-
ber, serial number, purchase date and exact cause or description of problem.
Table 4-1 Troubleshooting
PROBLEM
PROBABLE CAUSE
REMEDY
Uneven Cut
Cutter not level
side to side or
front to rear.
See SECTION III.
Belt slipping.
Adjust belt per
paragraph 4-3.
Worn or bent blade(s).
Replace blade(s).
Streaking or Windrowing
Possible build-up
of material under
cutter.
Clean cutter.
Cutter not level.
Worn blades.
Belt slipping.
See SECTION III.
Replace blades.
Adjust belt per
paragraph 4-3.
Noisy Cutter
Loose components.
Low oil in gearbox.
Check all bolts for
tightness.
Check oil per paragraph 4-2.
Rapid Blade Wear
(cutting edge)
Blade contacting
ground.
Adjust cutting height to
eliminate ground contact.
Cutter Vibrating
Cutter not being
operated at rated
PTO speed.
Set tractor throttle for
proper PTO speed.
Blade(s) bent.
Replace blades.
Remove object.
Foreign object wrapped
around spindle or blade.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION V
DEALER ASSEMBLY
CAUTION
AFTER COMPLETING ANY ASSEMBLY STEP,
THOROUGHLY READ THE NEXT STEP IN THE
ASSEMBLY INSTRUCTIONS BEFORE PRO-
CEEDING WITH THAT STEP.
THE FOLLOWING SAFETY PRECAUTIONS
SHOULD BE THOROUGHLY UNDERSTOOD
BEFORE ATTEMPTING MACHINE ASSEMBLY.
1. Wear personal protective equipment such as,
but not limited to, protection for eyes, ears, feet,
hands, lungs and head when assembling the equip-
ment. Do not wear loose clothing or jewelry that may
catch on equipment moving parts.
2. Do not lift heavy parts or assemblies. Use
crane, jack, tackle, fork trucks or other mechanical
devices.
3. Select an area for assembly that is clean and
free of any debris which might cause persons work-
ing on the assembly to trip.
4. Arrange parts to be assembled neatly in the
work area and have tools or other mechanical assist-
ing devices in easy reach.
11. After completing assembly, thoroughly inspect
the machine to be sure that all nuts, bolts, hydraulic
fittings or any other fastened assemblies have been
thoroughly tightened.
12. After completing assembly, be sure that all
safety locking devices or guards are in place.
13. Before operating the machine, thoroughly
read the operation section of this manual.
14. Before operating the machine, read the main-
tenance section of this manual to be sure that any
parts requiring lubrication such as gearboxes are full
to avoid any possible damage.
BEFORE OPERATING THE EQUIPMENT, IF YOU
HAVE ANY QUESTIONS REGARDING THE
PROPER ASSEMBLY OR OPERATION, CON-
TACT YOUR AUTHORIZED BUSH HOG DEALER
OR REPRESENTATIVE.
5. Inspect all parts and assemblies thoroughly and
remove any sharp edges, grease, oil or dirt which-
might cause pieces to slip when handling.
6. Preview the assembly instructions in your oper-
ator’s manual before proceeding further.
7. If the assembly instructions call for parts or
assemblies to be blocked up, use only blocking
material that is in good condition and is capable of
handling the weight of the assembly to be blocked.
Also, insure that the blocking material is on a clean,
dry surface.
8. Never put hands or any other part of body
under blocked up assemblies if at all possible.
9. Always wear goggles or safety glasses when
hammering, grinding, or drilling metal parts.
10. If the assembly calls for welding or cutting, be
sure that there are no flammable materials close at
hand and that bystanders have taken necessary pre-
cautions.
5-1 BASE UNIT ASSEMBLY (Figure 5-1)
A. Attach lower lift links to deck assembly using
3/4 x 2” bolts and lock nuts. Both bolts should be
tightened “snug”, but loose enough to allow link to
pivot. Slotted holes are provided to allow the mower
to more closely follow ground contours. (Figure 5-2)
B. Install lift pins onto lower links, securing with
7/8” lockwashers and hex nuts.
C. Attach mast halves to deck assembly using 1/2
x 1-1/2” bolts, lockwashers and hex nuts.
D. On each side of the mower, the mast support
will attach to the inside of the rear lug with the same
1/2” x 1-1/2” bolt and flanged lock nut that fastens
the caster arm to the outside of that same lug. Use a
1/2” x 1-1/2” bolt and flanged lock nut to fasten the
front end of the caster arm to the front mounting lug.
Repeat this procedure on the opposite side.
Flex Link
Figure 5-1
Mast
Gearbox
Mast Half
Support
Caster Arm
Figure 5-2
Spacers
Lower Lift Link
Lower Lift LInk
Slotted Hole
Behind Bolt
Lift Pin
14
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Fasten mast supports and upper flex link to
mast halves using 1/2 x 5” capscrew, pivot tube and
locknut.
F. Place two long spacers on the caster stems
and insert into caster arms. Place two long spacers
and two short spacers on the caster stem above the
caster arms. This arrangement will give a cutting
height of approximately 3-1/2 inches. Secure with
lynch pin retainers. With weight of cutter resting on
all four wheels, ensure that cutter is level. Tighten all
bolts on mounting brackets.
G. Fill gearbox with EP80W-90 gear oil until
oil level is at check plug on side of gearbox
housing. (Capacity is 1 quart) Replace solid fill
plug with breather plug supplied in operator’s
manual package.
RFM 60
Gearbox Oil Level
Check Plug
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY DECALS
To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage
can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide
safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for
more information.
50042283
50042285
50042282
50012616
78608
78786
83056
IMPLEMENT CAN FALL FROM HYDRAULIC
SYSTEM RELEASE. TO AVOID SERIOUS
INJURY OR DEATH:
SHUT OFF TRACTOR ENGINE, REMOVE KEY, SECURE
TRACTOR PARKING BRAKE AND BLOCK UP OR SECURELY
SUPPORT IMPLEMENT BEFORE WORKING UNDERNEATH.
•
STAND CLEAR IF LOWERING OR RAISING IMPLEMENT.
•
50042284
50042284
50012615
50042281
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TORQUE SPECIFICATIONS
Proper toque for American fasteners used on Bush Hog equipment.
Recommended Torque in Foot Pounds (Newton Meters).*
AMERICAN
BOLT DIAMETER
Bolt Head Markings
WRENCH
(IN.) “B” AND
THREAD SIZE
SAE
SAE
SAE
SIZE (IN.) “A”
GRADE 2
GRADE 5
GRADE 8
7/16
7/16
1/4 - 2O UNC
1/4 - 28 UNF
5/16 - 18 UNC
5/16 - 24 UNF
3/8 - 16 UNC
3/8 - 24 UNF
7/16 - 14 UNC
7/16 - 20 UNF
1/2 - 13 UNC
1/2 - 20 UNF
9/16 - 12 UNC
9/16 - 18 UNF
5/8 - 11 UNC
5/8 - 18 UNF
3/4 - 10 UNC
3/4 - 16 UNF
7/8 - 9 UNC
6 (7)
8 (11)
10 (13)
12 (16)
14 (18)
6 (8)
1/2
11 (15)
17 (23)
25 (33)
SAE Grade 2
(No Dashes)
1/2
13 (17)
19 (26)
27 (37)
9/16
20 (27)
31 (42)
44 (60)
9/16
23 (31)
35 (47)
49 (66)
5/8
32 (43)
49 (66)
70 (95)
5/8
36 (49)
55 (75)
78 (106)
3/4
49 (66)
76 (103)
106 (144)
120 (163)
153 (207)
172 (233)
212 (287)
240 (325)
376 (509)
420 (569)
606 (821)
668 (905)
909 (1232)
995 (1348)
1019 (1381)
1288(1745)
1444 (1957)
1817 (2462)
2013 (2728)
2382 (3228)
2712 (3675)
3161 (4283)
3557 (4820)
3/4
55 (75)
85 (115)
7/8
70 (95)
109 (148)
122 (165)
150 (203)
170 (230)
266 (360)
297 (402)
430 (583)
474 (642)
644 (873)
705 (955)
721 (977)
795 (1077)
890 (1206)
1120 (1518)
1241 (1682)
1470 (1992)
1672 (2266)
1950 (2642)
2194 (2973)
7/8
79 (107)
97 (131)
110 (149)
144 (195)
192 (260)
166 (225)
184 (249)
250 (339)
274 (371)
280 (379)
354 (480)
397 (538)
500 (678)
553 (749)
655 (887)
746 (1011)
870 (1179)
979 (1327)
SAE Grade 5
(3 Dashes)
15/16
15/16
1-1/8
1-1/8
1-5/16
1-5/16
1-1/2
1-1/2
1-1/2
1-11/16
1-11/16
1-7/8
1-7/8
2-1/16
2-1/16
2-1/4
2-1/4
7/8 - 14 UNF
1 - 8 UNC
1 - 12 UNF
Wrench
Size “A”
1 - 14 UNF
SAE Grade 8
(6 Dashes)
1-1/8 - 7 UNC
1-1/8 - 12 UNF
1-1/4 - 7 UNC
1-1/4 - 12 UNF
1-3/8 - 6 UNC
1-3/8 - 12 UNF
1-1/2 - 6 UNC
1-1/2 - 12 UNF
Proper torque for metric fasteners used on Bush Hog equipment.
Recommended torque in foot pounds (newton Meters).*
METRIC
WRENCH
BOLT
DIA.
SIZE
(mm) “A”
ASTM
4.6
ASTM
8.8
ASTM
9.8
ASTM
10.9
(mm) “B”
8
5
1.8 (2.4)
3 (4)
5.1 (6.9)
8.7 (12)
21.1 (29)
42 (57)
6.5 (8.8)
11.1 (15)
27 (37)
10
13
16
18
21
24
30
33
36
41
46
6
8
7.3 (10)
14.5 (20)
25 (34)
40 (54)
62 (84)
122 (165)
Wrench
Size “A”
10
12
14
16
20
22
24
27
30
53 (72)
8.8
74 (100)
118 (160)
167 (226)
325 (440)
443 (600)
563 (763)
821 (1112)
1119 (1516)
73 (99)
93 (126)
116 (157)
181 (245)
148 (201)
230 (312)
449 (608)
611 (828)
778 (1054)
1138 (1542)
1547 (2096)
Numbers appearing on bolt heads
indicate ASTM class.
*Use 75% of the specified torque value for plated
fasteners. Use 85% of the specified torque values
for lubricated fasteners.
211 (286)
418 (566)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
l
2501 Griffin Avenue Selma, AL 36703
l
Download from Www.Somanuals.com. All Manuals Search And Download.
|