R
GRC730
Download from Www.Somanuals.com. All Manuals Search And Download.
10
A
15
16
17
9
12
18
11
19
5
26
12
4
1
6
3
8
24
25
2
27
14 12
B1
B2 B3
11
13
10
18
7
17
14
12
Download from Www.Somanuals.com. All Manuals Search And Download.
C1
D1
F
C2
C3
D2
E
19
5
20
G1
G2
G3
G4
21
23
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Lawnmower
GRC730
Instruction Manual
This manual provides operating and maintenance
instructions for the Black & Decker GRC730
cordless lawnmower.
•
•
Before using your machine, remove
safety key and visually check that the
blade, blade nut and cutter assembly are
not worn or damaged. Damaged blades
and worn blade nuts must be replaced.
Also check that the blade nut is securely
fastened.
Know your machine
Read this manual carefully. Observe all the
recommended safety instructions before,
during and after using your machine, and
maintain your machine in good working order.
Always check that your lawn or cutting
path is clear of all sticks, stones, wire
and other debris. Contact with such
debris may damage your machine.
Familiarise yourself with the controls on your
machine before attempting to operate it, but
above all, be sure you know how to stop
your machine in an emergency.
Operation
•
When tilting the handle downwards for
starting, do not tilt it more than is
absolutely necessary. Always ensure that
both hands are in the operating position
and feet are well away from the blades
before returning the mower to the ground.
Retain this manual and all other literature
supplied with your machine for future
reference.
•
•
Avoid accidental starting. Ensure switch
is off when inserting safety key.
Safety instructions
Training
Release switch lever to turn mower off
and remove the safety key:
•
Never allow children or persons who are
unfamiliar with this type of machine to
use it, nor anyone who has not read
this leaflet.
•
Whenever you leave your machine
unattended.
•
Before checking, cleaning or working
on the mower.
Do not allow children, animals
or other persons near your
6m / 20ft
machine when in use - always
keep them at least 6m (20ft)
away from the cutting area.
•
•
Before clearing a blockage.
360
If the mower starts to vibrate
abnormally (check immediately).
•
Remember that the operator/user is
responsible for accidents or hazards
occurring to other people or their property.
•
After striking a foreign object.
Inspect the mower for damage and
make repairs as necessary.
Preparation
•
Never run the unit whilst on its’ side or
attempt to stop the blade - always allow
it to stop on its own.
•
•
•
To protect your feet, always wear stout
shoes or boots - freshly cut grass is
damp and slippery.
•
•
•
Do not put hands or feet near or under
rotating parts.
Use protective equipment. Wear safety
spectacles or goggles whilst mowing.
Use a face mask if dusty.
Keep clear of discharge openings at all
times.
Do not operate in gaseous explosive
atmospheres.
Start your machine carefully according to
the instructions and with your feet well
away from the blades.
•
•
Do not mow barefoot or in open sandals.
Wear long trousers to protect your legs -
any debris left on the lawn or cutting path
may be picked up and ejected by the
blades.
•
Avoid using the machine during rain and
avoid wet grass if possible.
•
•
Mow only in daylight or good artificial light.
Do not pull your machine towards you or
walk backwards when mowing.
•
Always be sure your machine is in a safe
operating condition.
•
Do not cross gravel paths or roads whilst
the blade is rotating.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
•
•
Always be sure of your footing,
particularly on slopes.
ENGLISH
Always mow across the face of slopes,
never up and down. Exercise extreme
caution when changing direction on slopes.
•
•
Do not cut excessively steep slopes and
always wear non-slip footwear.
•
Rechargeable 12V battery - provides
reliable power that will cut approx. 300m2.
Check the grassbag frequently for wear
or damage, and replace if necessary.
•
•
Easy to start - starts first time every time.
Specially designed switch box (16) and
safety key (24) to prevent accidental
starting of the mower.
•
•
Walk, never run. Do not force the mower.
Never pick up or carry your mower while
the motor is running. Ensure the blades
have stopped rotating when tilting for
transporting the mower to and from the
area to be mowed.
•
•
Ergonomically designed upswept handle
for comfortable use and ease of
pushing (10).
A blade brake (autostop) for added
safety - stops the blade from rotating
within 3 seconds once the switchbox
lever is released.
•
•
When transporting your unit, always
remove the safety key, adjust the cut
height setting to a mid position and take
extreme care when lifting.
•
•
•
Large handle wing nuts for easy
assembly and storage.
Never operate the mower with defective
guards or shields.
Single lever height of cut adjustment for
quick and easy operation (20).
Maintenance and storage
•
Store your machine in a dry place when
not in use, remove the safety key and
place out of the reach of children.
Five height of cut positions which
provides the flexibility to deal with most
grass conditions.
•
Do not use solvents or cleaning fluids to
clean your machine - use a blunt scraper
to remove grass and dirt. Always remove
the safety key before cleaning.
•
•
The in line wheels allowing cutting right
up to the edge of the lawn.
Large capacity grass bag (30 litres) for
longer cutting periods (19).
•
•
Do not charge or store the unit outdoors.
•
•
Easy grassbag removal.
Do not operate your machine if any parts
are defective; discard all defective parts
and fit new parts before use.
Smooth bottom deck design giving you a
better cut performance and an improved
quality of cut.
•
•
Replace worn or damaged parts for safety.
•
•
•
Tough, durable plastic deck which will
not rust and contributes to low noise and
low vibration.
Keep all nuts, bolts and screws tight to
be sure your mower is in a safe working
condition.
Rear roller (UK only) which produces the
traditional, striped effect on the lowest
height of cut.
•
Use only Black & Decker recommended
replacement parts and accessories.
Powerful and efficient 12V permanent
magnet motor which gives effective
cutting and bagging in all reasonable
conditions and a low noise level.
Features (Fig. A)
Your purchase of the Black & Decker
A
GRC730 lawnmower gives you a product
combining quality with modern design and
the following features, to provide safe,
efficient and easy mowing.
•
The GRC730 will have a run time under
average cutting conditions of
approximately 300m2. This run time will
vary upwards and downwards
•
•
•
Cordless - there is no need for extension
cables while mowing.
dependant upon grass conditions, cut
height used and push speed.
Gasless - there is no need for petrol and
oil to buy, mix, store or transport.
Black & Decker policy is one of continuous
improvement to their product and as such
they reserve the right to change product
specification without prior notice.
Clean - there are no emissions, the
mower is environmentally friendly.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
When both handles are assembled, fit
one cable clip (18) onto the upper handle
and one onto the lower handle. Clip the
cable into these ensuring the grassbox
can be removed and positioned freely.
B3 •
Unpacking and assembly
Your mower carton contains:
•
•
The mower and handle assembly.
One hardware bag containing:
•
•
•
Two safety keys (24).
Instruction literature.
Blade nut spanner (25).
Grassbag assembly (Fig. C)
Note: Ensure the battery is disconnected.
•
•
•
Charger (26).
Read the safety instructions at the beginning
of this manual before using this accessory.
Battery strap (27).
Before starting to assemble the grassbag,
check that the parts are similar to those
shown in Fig. C1.
C1 •
One grassbag assembly (19) - see below for
assembly instructions.
•
Secure the grassbag by inserting the bag
rim into the channel and pushing down
firmly until the clip feature locks onto the
bag rim (inset).
Handle assembly (Fig. A & B)
Remove the contents of the carton and
familiarise yourself with the individual parts of
the mower.
A
Push the support frame firmly into place.
C2 •
C3 •
The main parts of the mower shown in Fig. A
are as follows:
Assemble the two side clips to the
support frame, then assemble the
bottom clip.
•
Machine body (1):
•
•
•
•
•
•
•
Cutter deck (2)
Motor cover (3)
Battery cover (4)
Grass flap (5)
Wheel assembly (6)
Pivot pin (7)
Battery information
•
The battery in your cordless lawnmower is a
12 volt sealed lead acid system. The battery
employs an absorbed electrolyte and, can
therefore, be stored in any position without
fear of leakage.
Grill (8)
•
The battery has been charged at the factory,
however, it will be necessary to recharge the
battery to ensure full charge before initial use.
•
Handle (9):
•
•
•
•
•
•
•
Upper handle (10)
Lower handle (11)
Handle knob (12)
Switch lever (15)
Switch box (16)
•
•
For optimal performance the battery should
be recharged after each use.
For winter storage ensure:
•
•
The mower is fully charged before storing.
Electric cable (17)
Retaining clips (18)
The temperature of the storage location is
below 25˚C.
•
Storage duration is less than 6 months.
•
The lower handle (11) comes ready
assembled to the mower body.
•
•
Always store your mower in a dry and
cool location.
B1 •
All that is required is to unfold the handle
by lifting it until the handle ends snap into
their locations on the sides of the mower.
Once this is complete the knobs (12) can
be tightened.
Keep the mower and battery away from water,
heat sources (such as radiators, heaters, stoves
etc.), flames or chemicals.
Battery strap
B2 •
The upper handle (10) is assembled by
fitting the bolts (13) through the holes in
the lower handle, aligning the upper
handle over these and securing with a
washer (14) and then the knob (12).
•
•
Locate the battery and its carrying strap.
Fold the sides of the strap up and put the battery
in place.
•
•
Click the straps together ensuring you locate
every hole.
•
Tighten each one with hand pressure only.
Do not use a spanner.
The strap should be kept on the battery at all times.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Charging instructions
ENGLISH
•
Always charge your mower indoors in a
well ventilated area, where it is dry and
protected from the weather.
•
Charge mower in a location where the
temperature is more than 5˚C (41 F) and
˚
Important!
below 40˚C (104˚F).
Recharge mower to a fulI charge immediately
after use.
Warning! Do not attempt to charge
non-rechargeable batteries.
!
In order to get maximum performance from your
mower with maximum battery life, it is important that
you recharge the battery immediately after each use.
Battery failure will occur if the mower is stored
without having a full charge.
To charge
•
The battery on your mower can be
charged on the mower or can be
removed and charged away from the
mower if a mains socket is not at hand.
Recharge mower to a fulI charge for winter storage.
To charge the battery ON the mower
When preparing your mower for winter storage, it is
important that it is recharged. Battery failure will occur
if the mower is stored without having a full charge.
•
Remove the safety key (24) and store in a
safe place away from children.
•
Open the battery cover (4) by pressing in
the lock symbols at each side of the
cover and hinge upwards.
Battery disposal
When the mower’s battery requires replacing
discharge the energy from the battery by
running the mower until the motor stops.
Remove the battery from the mower .
•
•
Disconnect the battery lead (red and
black) by pulling it from the socket at the
side of the battery recess.
The red and black socket of the charger
is then connected to the red and black
socket of the battery.
Warning: The battery may still have some
residual charge even after the motor stops.
!
It is therefore necessary to protect against
accidental short circuit of the battery
terminals with uninsulated tools or materials
of a conductive nature, such as, but not
limited to steel wool or aluminium foil.
Note: The charger socket will fit one way only.
•
Connect the charger to the mains socket
and switch on.
•
The red indicator on the charger will turn
on. This indicates that the battery is
being charged.
Batteries must be disposed of in a
responsible manner.
•
When the battery becomes charged,
normal time 24 to 30 hours, the red light
will go out and the green light will turn on.
This symbol indicates the lead acid battery
contained within this unit must be disposed
of properly and not discarded in everyday
Pb
household waste which may be disposed of
in an incinerator or landfill site.
•
•
It is safe to leave your battery on charge
until ready to use.
-
+
Lead acid batteries can be harmful to the
environment and can explode when exposed
to fire. Do not incinerate.
Disconnect the charger from the battery
and connect the battery to the socket on
the mower.
The battery should be taken to a
Black & Decker service centre, your local
dealer or your local recycling station. If
necessary, contact your local authority for
disposal information.
•
Your mower is now ready for use.
To charge the battery OFF the mower
•
Remove the safety key and open battery
cover as described above and
disconnect the battery.
If the cutting performance begins to deteriorate,
please refer to the “Fault finding” guide.
•
Lift out battery out of the mower using
the carry handle.
Warning! Do not cross battery leads when
installing a new battery as this will cause the
blade to run in reverse until battery is
discharged. When you attempt to recharge
the battery, the charger circuit will be
destroyed as soon as you connect the
charger plug.
•
•
Charge as described above.
!
After charging, replace in mower and
connect to the mower socket.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
If, when grasscutting, loose grass is seen to be
scattered from beneath the mower, the grass-
bag is probably full and should be emptied.
How to use your machine
(Fig. D & E)
Important! Always observe all the relevant
warnings when using your machine.
Fitting the grassbag to the unit
•
•
Hold the grassbag top (19) by its handle.
Warning! Never attempt to operate your
machine with one hand. You must guide
your machine with both hands.
E
Lift the grassflap (5), then guide the
grassbag through the lower handle tube
and fix to the rear of the unit by lining up
the arrows marked on the cutter deck
and grassbag top.
!
Safety key
•
In order to prevent accidental start-up or
unauthorised use of your cordless
mower, a removable safety key has been
incorporated into the design of your
mower. The mower will be completely
disabled when this safety key has been
removed from the mower.
•
Finally, when this is complete, gently
release the grassflap (5) and it will return
to sit onto the location area of the
grassbag top (19).
Removing the grassbag
The full grassbag may be removed by raising the
grassflap (5) and then lifting the grassbag up and
through the lower handle.
Note: The safety key has a hole in the centre
to allow for storage on a hook, out of the
reach of children.
Warning! Always remove the safety key from
mower when leaving it unattended, even for
a short period of time.
!
Height of cut adjustment (Fig. F)
Warning! Remove safety key before making
•
Your safety key will be found in the
parts pack (plus one spare).
any adjustments and give the blade time to
stop rotating; cutting blades are sharp.
!
Starting
•
By moving the height of cut adjuster (20)
at the rear of your machine outwards
from the mower body and then up or
down as required, the height of cut can
be varied to give 5 positions.
•
•
•
Remove tie wrap from switch lever prior
to first use.
F
Insert the safety key into position and
push fully home.
Note: The 5 position height of cut adjuster
is under tension when in the engaged
position. It has to be sprung outwards to
move it from one height setting to another
and will spring back automatically into
position when released.
Tilt the handle downwards to slightly
raise the front of the mower to reduce
the risk of lawn damage whilst starting.
Your mower is equipped with a special
on/off switch lever. The switch lever is
recessed within the switch housing to
prevent turning the mower on accidentally.
D1 •
•
Settings 1, 2 and 3 are suitable for
course or overgrown grass. Settings 4
and 5 should be used for maintaining
cultivated lawns. Setting 5 should only be
used if a very short cut is desired.
To operate the switch, insert your finger
into the opening and push the lever out
so that you can pull it with your other hand.
Pull the lever back against the mower
handle and hold in this position to keep
the mower running.
D2 •
UK only
To produce a stripe effect on your lawn,
•
simply adjust the height of cut to its
lowest position, setting 5, which will bring
the roller into contact with the grass. The
roller may be removed for cleaning by
levering out one end to release the axle
from its clip.
•
To turn the mower off, just release the
lever. The spring-loaded “snap-action”
lever will relocate itself back into its
original position inside the switch housing.
When you have finished using your machine
we recommend that you clean all debris from
it before putting it away. It is important to
remove the safety key before cleaning. Please
refer to the “Care and maintenance” section.
Maintenance of blades
The steel blade is designed to give a fine
Note: To obtain the best results cut your
lawn or grassed area regularly and do not
cut when the grass is wet.
finish in long or tough grass.
If, however, because of damage or wear the
cutting performance deteriorates, then the
mower may require a new blade, or at least
the existing blade to be sharpened.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
We recommend that the steel blade is
sharpened or a new blade fitted at the
beginning of the season.
ENGLISH
Replacement blades A6157 are available from
Black & Decker dealers and service centres.
Warning! When fitting a new blade use only
the Black & Decker replacement part
specified for your machine - do not attempt
to fit any other blade.
Overload protection
Your machine is fitted with overload protection.
!
If you work too quickly in long grass, or in heavy
cutting conditions, you may overload the motor.
This will be indicated by a significant drop in speed,
and eventually, the overload protection will operate.
This is not a fault but a safety device to protect
your machine.
Fitting new blade (Fig. G)
Observe all the relevant warnings before
changing the blade.
Warning! Remove safety key before
changing the blade.
When this occurs, remove the safety key and wait for
1 to 2 minutes to allow to cool, clear any blockage
ensuring the blade is free to rotate. To restart,
replace the safety key and operate the switch lever.
Turn your machine over on its side so
that the underside of the cutter deck is
exposed.
G1•
If the cut-out operates again within 10 minutes, you
should increase the height of cut (see “Height of
cut adjustment”).
•
•
Wear gloves to protect hands.
Severe overloading may result in a longer delay on
restarting. In such cases, after resetting, you should
allow the motor to cool.
Using a cloth placed over the blade or
heavy duty gloves to protect your hands,
grip the blade and, using the spanner
provided, loosen and remove the nut
from the motor spindle. Turn the nut in an
anti-clockwise direction to loosen it.
To obtain the best results:
•
•
•
Cut the grass regularly.
Do not cut wet grass.
When the grass is longer than 10cm (4 inches),
it is advisable to go over the lawn on a high cut
setting and then finish using a lower setting.
Remove nut (23), square washer (22),
clutch plate (21) and blade.
G2•
•
To replace blade ensure the cutting
edges of the blade are closest to the
ground and place blade onto the
combined mount.
Care and maintenance
The advice given in this section covers the general
care and maintenance of the main body of your
mower. Advice relating to the blades is given in
“Maintenance of blades”. Advice relating to the
maintenance and storage of the battery is given in
“Battery information”.
Place the clutch plate over the shoulder
of the combined mount protruding
through the blade. Ensure to align the
inside edges with the outside edges of
the blade.
G3•
G4•
•
Place the square steel blade spacer on
the motor shaft aligning the inside flats
with the shaft and engaging the outside
edges with the plastic clutch plate.
Engage nut on shaft and turn it
clockwise to tighten.
•
Always keep your machine clean and free from
grass cuttings, especially the underside of the
cutter deck and the air vents.
•
At the end of each cutting session we
recommend that the build up of grass on the
underside of the cutter cover is removed using a
blunt scraper, the spanner included with this
mower may be used for this purpose.
Ensure that removed parts are replaced
correctly before use, incorrect assembly
may result in damage to your mower
and reduced cutting performance.
•
•
Clean all plastic components with a damp cloth.
Caution! Do not use solvents or cleaning fluids
as these may damage the plastic components of
your mower.
Note: This unit is fitted with a clutch plate
(24), between the blade nut and the blade,
which must be assembled correctly at all
times. Damaged blade assembly parts must
be replaced before use.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
•
The product has been used within the
parameters of its consumer classification.
Fault finding
If your mower does not operate correctly, use the
following table to locate the problem.
•
•
The product has not been used for hire purposes.
Repairs have not been attempted by anyone other
than authorised repairer agents.
Problem
Solution
Mower does not run
when switch lever
is activated
(a) Check to make sure safety key
has been inserted correctly.
(b) Remove the safety key, turn
mower over and check that the
blade is free to turn.
•
The failure represents normal wear and tear.
This guarantee is offered as an extra benefit and is
additional to your statutory rights.
(c) Has battery been fully
charged? Plug in charger and
wait for green light to come on.
What to do if your Black & Decker
product needs repair
If your Black & Decker product should need repair
the quickest and simplest way is to take or send it
back to a Black & Decker authorised repair agent,
providing proof of purchase if a guarantee repair
is required.
Mower stops when mowing
(a) Remove safety key. Turn
mower over and check that blade
is free to turn.
(b) Raise cutting height of wheels
and start mower.
(c) Has battery been fully
charged. Plug in charger and wait
for green light to come on.
(d) Check that safety key has not
fused. Replace if necessary.
If you have any difiiculty, please contact our sevice
and information centre (tel: 0345 230230) who will
give you every assistance.
Our guarantee policy
Failures due to the following are not covered:
Mower runs but cutting
performance is
unsatisfactory
(a) Has battery been fully
charged? Plug in charger and
wait for green light to come on.
(b) Battery may need replacing.
Refer to ‘Battery disposal’ section.
•
Replacing worn or damaged blades, nylon line
and chains, or cables damaged during storage
or use. These are regarded as replacement items
which wear during normal usage.
Mower is too hard to push
(a) Raise cutting height to
reduce drag on grass. Check
each wheel for ease of rotation.
•
•
Failures as a result of sudden impact or obvious
abuse.
Failures due to usage not in accordance with
instructions and recommendations contained in
the instruction manual.
Mower is abnormally noisy
and vibrates
(a) Remove safety key. Turn unit
on its side and check blade for
damage. If damaged replace with
Black & Decker replacement blade.
(b) If there is no visible damage
to the blade or underside of the
mower return to your local service
centre or authorised dealer.
The use of other than genuine Black & Decker
accessories and parts may damage or reduce the
performance of you Black & Decker product and
may render the guarantee void.
Black & Decker after sales service
Warning! Always remove safety key before
If you need any help or advice please contact your
local Black & Decker authorised repair agent. A full
directory is printed on the reverse of the parts
drawing included with your mower.
carrying out any inspection.
!
Black & Decker lawn and garden
guarantee
This guarantee provides 36 months parts cover
and 12 months labour. Proof of purchase will be
required.
Other Black & Decker products
Black & Decker has a full range of outdoor power
tools that make life easy in the garden. If you would
like further information on the following products,
please contact Black & Decker service information
centre at the address on the back cover, or contact
your Black & Decker stockist.
If your Black & Decker product becomes defective ,
within the guarantee period, due to faulty materials
and workmanship, we guarantee to either replace all
defective parts, or at our discretion, replace the unit
free of charge, provided that:
Lawnmowers
Grass trimmers
Lawnrakers
Leafbuster
Hedgetrimmers
Chainsaws
Compost shredder
•
The product is returned to us or our authorised
repairers with evidence of purchase.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
ENGLISH
EC Declaration of Conformity
We declare that unit: GRC730
conforms to 89/392/EEC, EN55104,
89/336/EEC, 73/23/EEC, EN60335, EN55014
A weighted sound pressure @ 4m 80dB (A)
A weighted sound power 91dB (A)
Hand/arm weighted vibration <2.5m/s2
Brian Cooke
Director of Engineering
Spennymoor, County Durham DL16 6JG, United Kingdom
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Australia
Black & Decker (A’asia) Pty Ltd
286-288 Maroondah Highway
North Croydon, Victoria 3136
Tel: 03 9213 8200
Fax: 03 9726 7150
New Zealand
South Africa
Black & Decker
483 Great South Road, Penrose, Auckland
Tel: 09 579 7600
Fax: 09 579 8200
Powerdek Tool Distributors
22 Inglestone Road, Village Deep
Johannesburg, South Africa
Tel: 011 493 4000
Fax: 011 493 6391
United Kingdom
Black & Decker
210 Bath Road
Slough
Tel: 0345 230230
Tel: 01753 511234
Tlx: 848317 BAND MH
Fax: 01753 551155
Berkshire SL1 3YD
Part no: 372324-01 3/97.3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Part no: 372324-01 3/97.3
Download from Www.Somanuals.com. All Manuals Search And Download.
|