PR & OS Owner’s Manual
Patent 6253416 and other patents pending
BILLY GOAT POWER RAKE AND OVERSEEDER
PR550, PR550H, OS552, OS552H
Owner's Manual
Accessories
Replacement Parts
SLICING REEL
A complete verti-
slicing reel for your
PR. 20" wide reel for
use in grasses that
require vertical
SLICING BLADES
A full set of blades for
replacement. Includes
new lockwashers for
replacement
OVERSEEDER KIT
The new light weight Plastic Overseeding
Kit is constructed of durable High Density
Polypropylene with two lift handles on
each side to assist in lifting the entire unit
and easily converts a PR Series Power
Rake into an overseeder with 4 bolts and
minimal tools.
FLAIL SHAFTS
FLAIL BLADES
A complete set of
our high quality flail
blades for your PR.
Includes new lock
clips for
A full set of shafts
for replacement.
Includes new lock
clips for
replacement
installation.
installation.
cutting, and for
assisting in lawn
replacement
installation.
NOTE: Overseeder Conversion Kit
(350328) includes Slicing Reel (350113).
Part No. (350325) comes with the
Overseeder Box only.
overseeding projects.
P/N 350187
P/N 350325 / 350328
P/N 350185
P/N 350113
P/N 350186
Part No 350412
Form No F061311C
1
PR & OS Owner’s Manual
Specifications
PR550
PR550H
OS552
OS552H
Engine: HP
5.5 (4.1 kW)
5.5 (4.1 kW)
5.5 (4.1 kW)
5.5 (4.1 kW)
Engine: Model
Engine: Type
12H1320118B8
GX160T1QX2
HONDA OHV
12H1320118B8
GX160T1QX2
HONDA OHV
B&S
B&S
VANGUARD
VANGUARD
Engine: Fuel Capacity
Engine: Oil Capacity
Total Unit Weight:
Engine weight:
3.0 qt. (2.84 L)
0.66 qt. (0.62 L)
149# (67.7 kg)
36# (16.3 kg)
15o
3.88 qt. (3.6 L)
0.69 qt. (0.65 L)
147# (66.8 kg)
34# (15.4 kg)
20o
3.0 qt. (2.84 L)
0.66 qt. (0.62 L)
162# (73.6 kg)
36# (16.3 kg)
15o
3.88 qt. (3.6 L)
0.69 qt. (0.65 L)
160# (72.7 kg)
34# (15.4 kg)
15o
Max. operating slope
Sound test in accordance with
2000/14/EC
101 dB(a)
101 dB(a)
101 dB(a)
101 dB(a)
Sound at operators ear
82 dB(a)
82 dB(a)
82 dB(a)
3.2g
82 dB(a)
3.2g
Vibration at operator position
0.82g (8.04 m/s2)
0.82g (8.04
m/s2)
SOUND
SOUND LEVEL 82 dB(a) at Operators Position
Sound tests were conducted in accordance with 2000/14/EC, and were performed on 2-13-2002 under the
conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on
the unit for the sound power level for your model.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Sunny
48oF (8.9oC)
2 mph (3.2 kmh)
South East
29%
Barometric Pressure:
30.34Hg (770 mm Hg)
VIBRATION DATA
VIBRATION LEVEL .82g (8.04m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using
calibrated vibration test equipment. Tests were performed on 5-25-2006 under the conditions listed below.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Sunny
72.32oF (22.4oC)
3.8 mph (6.12kph)
East
62.2%
Barometric Pressure:
29.9Hg (101.3kpa)
Part No 350412
Form No F061311C
3
PR & OS Owner’s Manual
INSTRUCTION LABELS
®
The labels shown below were installed on your BILLY GOAT Power Rake/Overseeder. If any labels are damaged or missing, replace them
before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering
replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL DANGER KEEP HANDS
AND FEET AWAY
LABEL CLUTCH ITEM #49
P/N 830503
DANGER FLYING DEBRIS LABEL SPARK ARREST
ITEM # 48 P/N 810736 ITEM #81 100252
ITEM #51 P/N 400424
LABEL CAUTION GUARDS
ITEM #52 P/N 900327
LABEL EXPLOSIVE FUEL
ITEM # 50 P/N 400268
LABEL INSTRUCTION HEIGHT ADJ.
ITEM #35 P/N 350176
LABEL INSTRUCTIONS SEEDER BOX
ITEM #30 P/N 350386
(page 15)
LABEL SEED METERING
ITEM #29 P/N 350392
(page 15)
ENGINE LABELS
BRIGGS & STRATTON
HONDA
OIL ALERT
WHEN OIL LEVELLOW,
ENGINE STOPS IMMEDIATELY.
ENGINE CONTROLS
Honda
Briggs & Stratton
Set lever to choke when starting cold
Throttle lever
Choke lever
Set lever to desired engine speed.
Move lever completely to the left to
stop engine
Fuel valve
Part No 350412
Form No F061311C
4
PR & OS Owner’s Manual
PACKING CHECKLIST
Your Billy Goat Power Rake is shipped from the factory in one carton, completely assembled.
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the
unit by cables.
PUT OIL IN ENGINE BEFORE STARTING
PARTS BAG &
LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-350412, General Safety and Warnings Manual P/N-
100295, Declaration of Conformity P/N-350139.
Boxing Parts
Checklist
Briggs & Stratton
5.5 B&S VANGUARD
26
28
Honda 5.5 OHV
Subaru 6HP EX17
28
28
Literature Assy
P/N-430334
PR550, PR550H,
PR550T, PR550HT,
PR600S
OS552, OS552H,
and OS602S
ASSEMBLY
1. UNFOLD the upper handle (item 26) and slide handle lock loops (item 28) into place to secure the upper handle
to the lower.
2. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move
height adjust lever to down position, to level engine during checking. See engine manufacturers instruction
manual.
3. CONNECT spark plug wire.
Part No 350412
Form No F061311C
5
PR & OS Owner’s Manual
OPERATION
FOLDING HANDLE
This unit is equipped with a folding upper handle for easier storage and transportation. The handle can be folded by
sliding the handle lock loops (item 28) up. This releases the upper handle, allowing it to be folded over the unit.
counter clockwise
to raise blades
ADJUSTING BLADE DEPTH
clockwise to
The depth of the blades can be raised or lowered by rotating the knob on the top of
lower blades
the adjustment lever. The blades are lowered by rotating the knob clockwise, and
raised by rotating the knob counter-clockwise. The relative depth of the blades can be
gauged by using the depth scale located on the right front corner of the engine base.
With new blades installed the depth can be estimated as follows: 2.5 on the scale is
even with the ground, 3 is equal to 0.25" deep, and 3.5 is equal to 0.5" deep
blades up
transport
blades up
transport
BLADE POSITION & DEPTH CONTROL LEVER
The blades can be raised or lowered into the ground by height adjustment lever on the
engine base. The height adjuster lock lever must be pushed back against the adjustment
lever in order to lower the blades into the ground. The resulting blade depth can be
adjusted higher or lower.
See ADJUSTING BLADE DEPTH.
blades down
running
SPRING TINE CONVERSION
If are converting your Power rake to a spring tine reel, you will need to
replace the spacer on the control lever to accommodate for the tine. First
remove the clip (item 18), then unscrew the yoke (item 17), remove the
washer (items 69) and insert the spacer (item 75) in front of the spring.
Reassemble in reverse order.
RAKING/SLICING TIPS
Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core
samples from area to be treated. A core can be cut using a piece of pvc, or metal pipe.
Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to
determine the depth of thatch in your yard.
THATCH: Thatch is a dense layer of dead grass, clippings, and roots that builds up over time
at the base of of the lawn preventing air, water, and fertilizer from reaching the soil. This can
cause shallow root development and make a lawn more susceptible to drought and disease.
Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of
thatch will keep your lawn in good health.
HEAVY THATCH: Lawns with an excessive amount of thatch will require multiple treatments
for effective removal. Trying to remove excessive thatch (greater than 3/4"[19 mm] deep) in
one treatment will damage or destroy the living part of the lawn. It is best to remove heavy
thatch in seasonal treatments (i.e. spring, and fall).
SLOPES: Rake slopes across not up and down. This is much easier and safer for the
operator and is better for the lawn. Raking across will help to reduce runoff during watering
and allow the sloped ground to hold more seed, fertilizer, and water. The units maximum
operating slope is 35% or 19°.
DEPTH: The wide range of depth adjustment on your unit is provided to allow for blade wear.
Setting the reel deeper will not produce better, or quicker results. The flail reel is intended to
be set so it just touches the surface on flat ground. The slicing reel should be set even with the
ground for verti-slicing work, and set to a maximum 1/2" depth for overseeding jobs. Setting
the reel deeper than this will only result in premature wear on the unit (i.e. failed belt). If you
desire to work the ground deeper than the above guidelines allow, it should be done gradually
in multiple passes..
Fig. 1
Fig. 2
SLICING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before
starting (i.e. approximately 2" tall for fescue grass). For the best result, Slice/Overseed in criss-
cross pattern (See Fig. 1 and See Fig 2).
Part No 350412
Form No F061311C
6
PR & OS Owner’s Manual
RAKING OPERATION-FLAIL REEL
NOTE: Must have the flail reel assembly (350112) for this operation.
MOW: Mow the lawn to it's normal cut height.
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat
surface (i.e. driveway, or sidewalk).
START ENGINE: See page 9 for further instruction.
ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the
blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the
operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into
the turf.
RAKE: Rake a small test area and examine the results. Thatch should be removed and
deposited on top of the healthy grass. If excessive damage occurs to healthy grass, adjust the
blade depth to decrease damage. Continue raking the yard, working in one direction (i.e.
north-south, or east-west). NOTE: If a large drop in engine RPM occurs, or the unit pulls you
forward and bounces during operation the blade depth is set too low.
REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn.
This thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We
suggest the use of a lawn vacuum or wheeled blower for collection and removal of the thatch.
RAKING OPERATION-SPRING REEL
NOTE: Must have the spring tine reel assembly (350354) for this operation.
MOW: Mow the lawn to it’s normal cut height. Tall grass will not leave a manicured look when the
dethatching job is complete.
DRY: Be sure grass is relatively dry. Wet conditions can cause increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that the spring tines are just above touching the
flat surface (i.e. driveway, or sidewalk) the units height is being adjusted on. NOTE: Allowing the
spring tines to have substantial contact with the ground will cause premature wear and failure of the
spring tines.
START ENGINE: See page 9 for further instruction.
ENGAGE TINES: Pull back on the bail on the operators handle. NOTE: When engaging the spring
tines in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators
handle lifting the front wheels slightly. Engage the spring tines. Slowly lower the unit into the turf.
RAKE: Rake a small test area and examine the results. Thatch should be removed and deposited on
top of the healthy grass. If excessive damage occurs to healthy grass, adjust the spring tine depth to
decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).
NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during
operation the spring tine depth is set too low.
REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn. This
thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We suggest the use
of a lawn vacuum or wheeled blower for collection and removal of the thatch.
VERTI-CUTTING OPERATION
NOTE: Must have the slicing reel assembly (350113) for this operation.
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface
(i.e. driveway, or sidewalk).
START ENGINE: See Page 9.
ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the
blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the
operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the
turf.
SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should
be removed and deposited on top of the healthy grass. Grass runners should be cut and ready
for removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease
damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).
NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during
operation the blade depth is set too low.
REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited
over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection
and removal of the thatch/stems.
Part No 350412
Form No F061311C
7
PR & OS Owner’s Manual
OVERSEEDING OPERATION
NOTE: Must have the slicing reel assembly (350113) for this operation.
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
2
SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft [4.5
2
kg. per 93 m ])
SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm)
below a flat surface (i.e. driveway, or sidewalk).
START ENGINE: See Page 9.
ENGAGE CLUTCH: Pull back on the bail on the operators handle. NOTE: When engaging the
clutch in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators
handle lifting the front wheels slightly. Engage the clutch. Slowly lower the unit into the turf.
SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If
excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue
raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in
engine RPM occurs, or the unit pulls you forward and bounces during operation the blade depth is
set too low.
WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to
the seed suppliers directions.
ADJUSTING SEED RATE
LAWN PREPARATION
- MOW LAWN TO LOWEST SETTING ON
YOUR MOWER.
- DO NOT WATER PRIOR TO SEEDING.
- POWER RAKE TO DETHATCH LAWN
AND REMOVE THATCH.
- FERTILIZE LAWN WITH BROADCAST
SPREADER.
LAWN PREPARATION
- FOR BEST RESULTS OVERSEED IN
TWO PASSES OF ONE-HALF
APPLICATION RATE EACH, AT RIGHT
ANGLES OR IN A CRISS-CROSS
PATTERN.
- WATER HEAVILY IMMEDIATELY THEN
LIGHTLY FOR 10 - 14 DAYS, KEEPING
SOIL MOIST.
- AFTER GERMINATION, WATER LESS
OFTEN TO PROMOTE ROOT GROWTH.
Part No 350412
Form No F061311C
8
PR & OS Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Inspect for loose, worn or damaged parts.
Check engine oil
Every Use (daily)
Every 25 Hours
z
z
z
z
z
Inspect belt
Engine (See Engine Manual)
Grease reel bearings
z
Inspect and clean engine air filter
Oil height adjustment linkage
FLAIL BLADE WEAR
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure the
overall length of the blade. (See fig. 1)
5. If blades measure less than 3.25"(83 mm) in overall length they must be replaced. NOTE: We
recommend replacing all the flails at once.
SLICING BLADE WEAR
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure
the overall length of the blade from the center of the attachment bolt to the tip of the worn
blade.
Fig. 1
5. If blades measure less than 3"(76 mm) in length they must be replaced. NOTE: We
recommend replacing all the blades at once.
ROTATING FLAIL REEL END TO END
To maximize flail blade life and performance the reel can be rotated end to end periodically to provide a fresh lead cutting edge. Takes approx. 20 min.
and requires 1/2" and 9/16" socket wrenches with extension bar.
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Remove (7) lock nuts (item 62 & 40) holding the belt and shaft guards (item 21 & 22) in place. It is necessary to lower the height adjust lever to reach
the locknuts on the guards. Remove the guards.
5. Remove the drive belt (item 9) by "walking" it out of the groove on the reel pulley (item 2).
6. Remove the (4) lock nuts (item 60) and washers (item 68) holding the bearings (item 23) to the frame of the unit.
7. The reel is now free from the machine. Slide the reel down and out of the machine.
8. Remove the capscrew (item 71), lockwasher (item 57), reel pulley (item 2), key (item 42), and reel spacer (item 10) from the end of the reel.
9. Rotate the reel end to end, and re-install these items on the opposite end of the reel.
10. Re-install the reel in reverse order of removal. Re-install the guards in reverse order of removal.
DRIVE BELT REPLACEMENT
NOTE: Takes approx. 10 min. and requires 1/2" socket wrench with extension.
1. Wait for engine to cool and disconnect spark plug.
2. Remove (4) lock nuts (item 62) holding the belt guard (item 21) in place. It is necessary to lower the height adjust lever to reach the locknuts on the
guard. Remove the guard.
3. Remove the belt (item 9) by rotating the reel pulley (item 2) and walking it out of the groove. Discard old belt
4. Install new belt using same procedure to walk the belt into the groove.
5. With new belt installed pull bail rod back to engaged position and measure extension of idler spring. Spring should stretch 3/4" - 1" (19 25 mm) with
bail engaged. Adjust clutch cable as necessary to achieve this extension.
6. Re-install the belt guard.
Part No 350412
Form No F061311C
9
PR & OS Owner’s Manual
Troubleshooting
Problem
Possible Cause
Solution
Abnorm al vibration.
· Dam aged or m issing blades. Loose
handle bolts. Loose engine bolts
· Stop work im m ediately. Replace any
dam aged or m issing blades. Tighten all
loose nuts and bolts.
Engine stalls or labors when
raking
· Blades set too deep into ground.
· Raise blades so that they just touch the
ground on a level surface
Engine will not start.
· Stop switch off (Honda only). Throttle · Check choke position.
in off position
· O ut of gasoline or bad, old gasoline. · Check gasoline.
· Spark Plug wire disconnected.
· G as valve off.
· Connect spark plug wire.
· Turn on gas valve.
· Dirty air cleaner.
· Clean or replace air cleaner. Contact a
qualified service person.
Engine is locked, will not pull
over.
· Debris locked against reel, or drive
pulleys. Engine problem .
· Pull spark plug wire and rem ove debris.
Contact an engine servicing dealer for
engine problem s.
Part No 350412
Form No F061311C
10
PR & OS Owner’s Manual
POWER RAKE SEEDER BOX KIT
P/N 350395
ITEM NO.
23
PART NO.
8041026 SCREWCAP 5/16-18 x 3/4
350372 BELT O-RING 5/16 X 15 9/16"
8197031 PIN COTTER 1/8" X 1"
9195106 ROLL PIN 1/8 - 1 1/4
8172020 WASHER 5/16 FENDER
8172007 WASHER 1/4 SAE
DESCRIPTION
QTY
4
1
1
1
4
3
1
1
2
1
1
1
1
1
1
1
PARTS LIST
ITEM NO.
PART NO.
350366
350390
350385
350320
350271
350272
350387
350370
8172009
900321
890108
400217
8024040
8024021
8123087
8160001
350389
8160002
8177011
350369
350280
DESCRIPTION
BOX AND LID ASSEMBLY
QTY
1
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
1
2
3
4
5
6
7
9
10
11
12
13
14
15
16
17
18
19
20
21
22
BRACKET CABLE MOUNTING
CABLE SEED METERING ASSY
SHAFT PLASTIC DROP SEEDER
PLATE DOOR DROP SEEDER
PLATE DOOR DROP SEEDER END
PLATE DOOR DROP SEEDER END ARM
PULLEY 3V GROOVE 0.625" BORE
WASHER #10 3/8 SAE
1
1
1
1
1
1
1
1
4
1
2
1
1
4
1
1
350392
350386
900230
LABEL SEED METERING
LABEL DROP SEEDER BOX
WASHER 1/2 FC
8161044 NUT LOCK 1/2" THIN HGT
890456
350313
LABEL HOSE PLUG KD/SV
LABEL PRODUCT DECAL OS
BEARING CLIP 1.375 OD
KNOB WING 5/16-18
SPRING TENSION
8024061 CARRIAGE BOLT 3/8-16 X 1 3/4"
8024025 CARRIAGE BOLT 1/4-20 X 1 3/4"
BOLT CARRIAGE 5/16 - 18 X 1
BOLT CARRIAGE 1/4-20 X 3/4"
SCREW SELF TAP #10-24 X 3/8" HMS ZP
NUT LOCK 1/4
BRACKET CABLE SEEDER BOX
NUT LOCK 5/16
WASHER LOCK 5/16
PULLEY 3V GROOVE 1.530" BORE
WASHER 0.906 O.D. X 0.656 I.D. X 0.062
350399
900471
PIN CLEVIS .25 X .61
PIN HAIR 1/4 ZP
8160003 NUT LOCK 3/8-16 HEX
8171004 WASHER 3/8 FC
1
2
1
1
1
1
40
41
42
43
350391
BRACKET MOUNTING METERING SEED
1
4
1
7-8
8059135 SCREW MACHINE #10-24 X 5/8
8164005 NUT LOCK LT #10-24 HEX
44
900407
TY-WRAP
Part No 350412
Form No F061311C
11
PR & OS Owner’s Manual
FLAIL REEL KIT 350112
PARTS DRAWING
item
no.
QTY
PARTS
LIST
Part No.
8177012
8171004
8041050
350141
350100
350144
350145
350146
8172011
1
1
1
57 LOCK WASHER 3/8 S/T MED
68 WASHER 3/8 FLAT CUT
71 SCREWCAP REEL PULLEY
73 SHAFT FLAIL BLADE
74 BLADE FLAIL
76 SPACER BUMPER 5/8" x 1/2"
77 SHAFT WA FLAIL REEL
78 CLIP LOCK 1/2"
4
30
54
1
8
8
79 WASHER 1/2 SAE
FLAIL SHAFT KIT 350185
FLAIL BLADE KIT 350186
PARTS
LIST
Part No. QTY
item
no.
PARTS
LIST
Part No. QTY
item
no.
74 BLADE FLAIL
350100 60
73 SHAFT FLAIL BLADE
78 CLIP LOCK 1/2"
350141
350146
4
8
78 CLIP LOCK 1/2"
350146
8
SPACER BUMPER KIT 350258
SLICING BLADE KIT 350187
item
no.
PARTS
LIST
QTY
item
no.
PARTSLIST
QTY
Part No.
Part No.
76 SPACER BUMPER 5/8" x 1/2"
350144
54
81 BLADE 10" HEX SLICING
350147
20
40
40
85 SCREWCAP 1/4-20 X 3/4 HCS ZP 8041004
86 NUT LOCK 1/4-20
8142004
Part No 350412
Form No F061311C
12
PR & OS Owner’s Manual
SLICING REEL ASSY 350113
PARTS DRAWING
PARTS
item
no.
57
71
80
81
82
83
84
85
86
87
88
89
90
PR500
Part No.
8177011
400389
350142
350147
350148
350149
350150
8041004
8142004
350152
350153
350154
350155
QTY
LIST
LOCK WASHER 5/16 S/T MED
SCREWCAP 5/16 - 24 x 1 1/4" HCS GR. 5
SHAFT SLICING WA
1
1
1
BLADE SLICING REEL
PLATE BLADE MTG.
20
20
10
9
SPACER BLADE MTG.
SPACER BLADE ASSY
SCREWCAP 1/4-20 x 3/4, HCS ZP
NUT LOCK 1/4-20
40
40
1
COLLAR SPACER
WASHER 0.937 x 1.750 x 0.119
WASHER LOCK 7/8 INT. TOOTH
NUT JAM 7/8"-14
1
1
1
SPRING TINE REEL ASSY - 350355-S
item
Part No.
QTY
PARTS
LIST
no.
1
2
3
4
SHAFT WA SPRING TINE REEL
SHAFT SPRING TINE REEL
SPRING TINE
RING RETAINING 1/2"
SCREWCAP3/8"-16 X 1" HCS ZP
WASHER LOCK 3/8 S/T MED
350353
350351
350352
350146
8041050
8177012
8171004
1
4
108
8
1
1
5
6
68 WASHER 3/8 FLAT CUT
1
SPRING REPLACEMENT KIT - 350356-S
item
no.
3
PARTS
LIST
QTY
Part No.
350352
350146
SPRING TINE
RING RETAINING 1/2"
108
8
4
Part No 350412
Form No F061311C
13
PR & OS Owner’s Manual
PARTS DRAWING
PR550, PR550H, OS552,
OS552H,
Part No 350412
Form No F061311C
14
PR & OS Owner’s Manual
PARTS LIST
PARTS
LIST
PR550
PR550H
OS552
OS552H
item
no.
QTY
QTY
QTY
QTY
Part No.
350101
350411
350102
350103
350104
350107
350112
350114
350115
350116
Part No.
350101
350411
350102
350103
350104
350107
350112
350114
350115
350116
Part No.
350101
350411
350102
350103
350104
350107
350113
350114
350115
350116
Part No.
350101
350411
350102
350103
350104
350107
350113
350114
350115
350116
1 Pulley 3" OD
1A Spacer 1" OD X .75" x .45 THK
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
3
4
5
6
7
8
9
10
Pulley 6.5" OD X ¾"
WHEEL 8.0" X 5/8" BEARING
WHEEL 10.0" X 5/8" BEARING
Height Adjust Assy
Reel Flail / Slicing / Spring Assy
Pulley Idler 2.75"
ArmIdler WA
Belt 5L X 36
11 Bracket Mount Clutch Cable
12 Chassis WA W/ Label
13 Frame Front WA
350119
350194
350121
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
-
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350384
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350408
500114
600115
-
9201078
400570
500181
-
350193
350301
810736
830503
-
400424
900327
890132
8024061
8024043
8024039
8177012
-
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
-
2
2
1
-
1
1
1
1
-
2
1
2
4
2
4
1
-
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350384
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350408
500114
-
350379
9201078
400570
500181
350288
350193
350301
810736
830503
100261
400424
900327
890132
8024061
8024043
8024039
-
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
-
1
2
2
1
1
1
1
1
1
1
2
1
2
4
2
5
-
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350384
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350408
500114
600115
-
9201078
400570
500181
350288
350193
350301
810736
830503
-
400424
900327
890132
8024061
8024043
8024039
-
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
-
2
2
1
1
1
1
1
1
-
2
1
2
4
2
5
-
14 Bushing 0.375 OD X 0.256 ID X 0.88 350309
15 Spring Height Adjust PR500
16 Link Height Adjust PR500
17 Yoke ½ - 20
350125
350126
350127
350128
350182
350130
350384
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350408
500114
-
18 Pin Yoke ½"
19 Bracket Mount Hgt. Adj. WA
20 Spacer Spanner Wheel PR500
21 Guard Belt WA W/ Label
22 Guard Shaft WA W/ Label
23 Bearing ¾" Cast Pillow Block
24 Handle Lower LH WA
25 Handle Lower RH WA
26 Handle Upper PR500
27 Bail Clutch WA
28 Loop Folding Handle
29 Deflector Rubber
30 Shield Bearing
31 Bar Clamp Deflector
32 Bracket Height Adjust Lock WA
33 Guard Pulley Back
34 Lever Height Control
35 Label Instr. Hgt. Adj.
36 Bolt Shoulder ¼" x 1 ¾"
37 Bolt Shoulder 5/16" x 1 ¾"
38 Cable Clutch PR
40 BOLT SHOULDER 1/2" X 1"
41 ENGINE HONDA 5.5 H.P. GX160
ENGINE 5.5 HP B&S VANGUARD
42 KEY 3/16" X 1"
350379
9201078
400570
500181
-
1
2
2
1
-
43 GRIP 1" x 13"
44 GRIP LEVER 1/8 x 1 x 5"
45 LABEL INSTRUCTION SEEDER BOX
46 LABEL PRODUCT DECAL OVAL
47 FINGER BELT WIRE
48 LABEL DANGER THROWN OBJECT
49 LABEL CLUTCH VQ
50 LABEL WARNING FUEL EN/SP
51 LABEL WARNING
52 LABEL DANGER GUARD
53 PLUG CAP 1" RD
54 BOLT CARRAIGE 3/8-16 x 1 3/4
55 BOLT CARRAIGE 5/16-18 x 1 3/4
56 BOLT CARRIAGE 5/16 -18 x 3/4
57 WASHER LOCK 3/8" S/T MED
WASHER LOCK 5/16" TW TOOTH
58 NUT LOCK #10-24
350193
350301
810736
830503
100261
400424
900327
890132
8024061
8024043
8024039
8177012
-
1
1
1
1
1
2
1
2
4
2
4
1
-
430298
8164005
8160001
8160003
1
1
5
12
430298
8164005
8160001
8160003
1
1
5
12
8164005
8160001
8160003
1
2
12
8164005
8160001
8160003
1
2
12
59 NUT LOCK 1/4-20
60 NUT LOCK 3/8-16
61
62 NUT LOCK 5/16-18
63 SCREWCAP 1/4-20 x 1 1/2
64 SCREWCAP 3/8 - 16 x 1 3/4
8160002
8041008
8041053
15
1
1
8160002
8041008
8041053
15
1
1
8160002
8041008
8041053
16
1
1
8160002
8041008
8041053
16
1
1
Part No 350412
Form No F061311C
15
PR & OS Owner’s Manual
PARTS
LIST
PR550
Part No.
PR550H
Part No.
OS552
Part No.
OS552H
Part No.
item
no.
QTY
QTY
QTY
QTY
65 SCREWCAP 5/16-24 x 3/4" GR.5
65A Washer 3/4 SAE
8042026
8172015
430298
8041030
400164
8171004
8172011
8161044
8041050
350266
520031
791080
2
5
1
4
1
9
2
4
1
4
2
2
8042026
8172015
430298
8041030
400164
8171004
8172011
8161044
8041050
350266
520031
791080
2
5
1
4
1
9
2
4
1
4
2
2
8042026
8172015
430298
8041030
400164
8171004
8172011
8161044
400164
-
3
5
1
4
1
8
5
4
1
-
8042026
8172015
430298
8041030
400164
8171004
8172011
8161044
400164
-
3
5
1
4
1
8
5
4
1
-
65B Washer 5/16 Twist Tooth
66 SCREWCAP 5/16 - 18 x 1 1/2
67 SCREWCAP 5/16-24 X 1
68 WASHER 3/8 FLAT CUT
69 WASHER 1/2 SAE ZP
70 NUT LOCK 1/2" - 13 THIN HGT
71 SCREWCAP REEL PULLEY
72 BUTTON SOCKET 5/16-18X5/8”
73 BOLT SHOULDER 1/2" x 2"
74 FLANGESCREW 0.375 -16 X 0.75
75 SPACER 1/2" ID X 3/4"
520031
791080
2
2
520031
791080
2
2
-
-
-
-
-
-
-
-
76 WASHER 3/8 SAE
77 NUT PAL 3/8
8172009
360218
8171002
520119
360279
-
8172007
890456
-
2
2
5
2
2
-
1
1
-
8172009
360218
8171002
520119
360279
100256
8172007
890456
-
2
2
5
2
2
1
1
1
-
8172009
360218
8171002
520119
360279
-
8172007
890456
441150
8171003
520116
2
2
5
2
2
-
1
1
1
5
1
8172009
360218
8171002
520119
360279
100256
8172007
890456
441150
8171003
520116
2
2
5
2
2
1
1
1
1
5
1
78 WASHER 1/4 FLAT CUT
79 PIN CLEVIS 3/8" X 1.625
80 RETAINER 3/8" BOLT PUSH NUT
81 LABEL SPARK ARRESTOR EN/SP
82 WASHER 1/4 SAE
83 LABEL LOGO PRODUCT SM CIRCLE
90 WASHER 1.125" OD X .344 ID X .25 THK
100 WASHER FLAT 5/16"
8171003
520116
5
1
8171003
520116
5
1
104 LABEL MADE IN U.S.A.
Part No 350412
Form No F061311C
16
|