HW Owner’s Manual
H
I
G
H
W
E
E
D
M
O
W
E
R
BILLY GOAT HIGH WHEEL MOWER
Owner's Manual
HW651SP & HW651HSP
Accessories
Grass Catcher Kit
Easily convert your
mower to bag grass
and leaves.
P/N 510223
Part No 510267
Form No F052808A
1
HW Owner’s Manual
SERIAL PLATE DATA
Record the model number, serial number, date of
purchase, and where purchased.
Purchase Date:
Purchased From:
Specifications
HW651SP
HW651HSP
Engine: HP
6.0 (4.5 kW)
6.5 (4.85 kW)
Engine: Model
FJ180V
Kawasaki OHV
2.1 qt (2.0 L)
0.63 qt. (0.6 L)
156# (70.8 kg)
15o
GSV190
HONDA OHV
1.6 qt (1.5 L)
0.69 qt (0.65L)
156# (70.8 kg)
15o
Engine: Type
Engine: Fuel Capacity
Engine: Oil Capacity
Total Unit Weight:
Max. operating slope
Overall length
62”(1.57m)
32”(0.81m)
43”(1.09m)
100.48dBa
80.48dBa
62”(1.57m)
32”(0.81m)
43”(1.09m)
100.48dBa
80.48dBa
Overall width
Overall height
Lwa at operator position
Lpa at operator position
Vibration at operator position
2.57g
2.57g
Part No 510267
Form No F052808A
3
HW Owner’s Manual
GENERAL SAFETY INSTRUCTIONS and SYMBOLS
The safety symbols shown below are used throughout this manual. You should become familiar with them before
assembling, operating, or servicing this equipment.
This symbol indicates important information that will prevent injury to yourself or others.
This symbol indicates ear protection is recommended when operating this equipment.
This symbol indicates eye protection is recommended when operating this equipment.
This symbol indicates gloves should be worn when servicing this equipment.
This symbol indicates that this manual and the engine manufacturer’s manual should be read
carefully before assembling, operation, or servicing this equipment.
This symbol indicates important information that will prevent damage to your BILLY GOAT ®
HW Mower.
This symbol indicates the engine oil level should be checked before operating this
equipment.
Read and make sure you thoroughly understand the following safety precautions before assembling, operating or
servicing this equipment:
READ this manual and the engine manufacturer’s manual carefully before assembling,
operating, or servicing this equipment.
EAR PROTECTION is recommended when operating this equipment.
EYE PROTECTION is recommended when operating this equipment.
BREATHING PROTECTION is recommended when operating this equipment.
EXHAUST from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land
unless a spark arrester is installed on the muffler as required by Section 4442 of the
California Public Resources Code. The arrester must be maintained in good working order.
Other states may have similar laws. Federal laws apply on federal lands.
DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an
odorless and possibly fatal poison.
Part No 510267
Form No F052808A
4
HW Owner’s Manual
DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors is recommended.
DO NOT refuel this equipment while the engine is running. Allow engine to cool for at least two minutes before refueling.
DO NOT store gasoline near an open flame.
DO NOT remove gas cap while engine is running.
DO NOT start or operate engine if strong odor of gasoline is present.
DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill until gasoline has completely evaporated.
DO NOT smoke while filling the fuel tank.
DO NOT check for spark with spark plug or spark plug wire removed. Use an approved spark tester.
DO NOT operate engine without a muffler. Inspect muffler periodically and replace if necessary. If equipped with muffler deflector,
inspect deflector periodically and replace if necessary.
DO NOT operate engine with grass, leaves or other combustible material near the muffler.
DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may cause severe burns.
DO NOT leave equipment unattended while in operation.
DO NOT park equipment on a steep grade or slope.
DO NOT operate equipment with bystanders in or near the work area.
DO NOT allow children to operate this equipment.
DO NOT operate equipment with guards removed.
DO NOT operate equipment near hot or burning debris or any toxic or explosive materials.
DO NOT operate equipment on slopes greater than specified in Specifications section of this manual.
DO NOT operate barefoot or wearing open sandals. Always wear substantial footwear
DO NOT place hands or feet underneath unit, or near any moving parts.
DO NOT pull mower backwards unless absolutely necessary
DO NOT operate the mower while under the influence of alcohol or drugs.
DO NOT operate mower in wet grass. Always be sure of your footing; keep a firm hold on the handle and walk; never run.
DO NOT mow on wet grass. Reduced footing could cause slipping.
DO NOT mow near drop-offs, ditches, or embankments. The operator could lose footing or balance
DO NOT mow excessively steep slopes.
DO NOT change the engine governor setting or overspeed the engine.
ALWAYS Stop the blade(s) when crossing gravel drives, walks, or roads.
ALWAYS Shut the engine (motor) off and wait until the blade comes to complete stop before removing grass catcher.
ALWAYS Mow only in daylight or good artificial light.
ALWAYS Disengage the self-propelled mechanism or drive clutch on mowers so equipped before starting the engine.
ALWAYS wear safety goggles or safety glasses with side shields
ALWAYS remove spark plug wire when servicing equipment to prevent accidental starting.
ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if necessary.
ALWAYS store fuel in approved safety containers.
WARNING: Important
Remove all rocks, wire, string, etc. that can present a hazard during work prior to starting.
DO identify and mark all fixed objects to be avoided during work such as sprinkler heads, water valves, limbs, or clothes line
anchors, etc.
Part No 510267
Form No F052808A
5
HW Owner’s Manual
SOUND
SOUND LEVEL 80 dB(a) at Operator Position
Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 2-21-2002 under the
conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on
the unit for the sound power level for your model.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Sunny
49oF (9.4oC)
8 mph (12.8 kmh)
South East
53%
Barometric Pressure:
30.15Hg (102.1kpa)
VIBRATION DATA
VIBRATION LEVEL 2.57g (25.20m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using
calibrated vibration test equipment. Tests were performed on 5-26-2006 under the conditions listed below.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Sunny
87.44oF (30.8oC)
3.1 mph (5.04kph)
South East
41.5%
Barometric Pressure:
29.89Hg (101.25kpa)
INTENDED USE
INTENDED USE: This unit is mainly designed for cutting grass. Some overgrown weeds, and taller grass may also
be cut. Be sure to inspect work area and machine before operating. Make sure that all operators of this equipment
are trained in general machine use and safety.
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check
for damaged or worn blade, loose blade jam nut, loose engine or lodged foreign objects. Note: See maintenance
section for proper blade jam nut torque specifications.
Part No 510267
Form No F052808A
6
HW Owner’s Manual
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT ® HW Mower. If any labels are damaged or missing, replace them before operating
this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The
correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL DANGER KEEP HANDS LABEL OILCHAIN #49 DANGER FLYING DEBRIS LABEL CLUTCH BLADE LABEL CLUTCH DRIVE
AND FEET AWAY
ITEM#62 P/N 830502
ITEM #111 P/N 810736
ITEM #84 P/N 500177
ITEM #101 P/N 500176
ITEM #61 P/N 400424
LABEL WARNING GUARDS LABEL EXPLOSIVE FUEL
ITEM #63 P/N 900327 ITEM # 48 P/N 400268
LABEL CUTTING HEIGHT
ITEM #58 P/N 510147
LABEL WARNING MOWER
ITEM #60 P/N 510206
LABEL MOWER INSTRUCT.
ITEM #59 P/N 510207
LABEL EAR EYE BREATHING
ITEM #110 P/N 890254
LABEL READ MANUAL
ITEM #109 P/N 890301
ENGINE LABELS
KAWASAKI
HONDA
THROTTLE CONTROLS
FIXED THROTTLE
Engine speed is factory set.
SPEED CONTROL
Push forward for faster speed, pull
back for slower speed
Part No 510267
Form No F052808A
7
HW Owner’s Manual
PACKING CHECKLIST
Your Billy Goat HW Mower is shipped from the factory in one carton, completely assembled except for the
upper handle.
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box the Handle Assembly is attached and
folded over
PUT OIL IN ENGINE BEFORE STARTING
PARTS BAG &
LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-510267
Boxing Parts
Checklist
Kawasaki
Honda
Literature Assy
P/N-510256
ASSEMBLY
1. REMOVE unit from carton and allow upper handle (item 7) to lay on ground behind unit.
2. REMOVE hardware items 8, 71, 78, 87, 96, & 97 from temporary storage positions on lower handles (items 10).
3. ATTACH lower handle (item 10) to the main frame using hardware (items 71, 78, & 96) removed from the previous step (see
figure above).
4. ATTACH upper handle to lower as shown in page 14, and securely tighten all fasteners.
Note: Be sure the engine starter rope is properly installed in the starter rope guide (item 8) before tightening the corresponding
fasteners (see figure above).
5. CONNECT spark plug wire to spark plug.
Part No 510267
Form No F052808A
8
HW Owner’s Manual
OPERATION
Like all mechanical tools, reasonable care must be used when operating machine.
Inspect machine work area and machine before operating. Make sure that all operators of this
equipment are trained in general machine use and safety.
PUT OIL IN ENGINE BEFORE STARTING
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately
and check for damaged or worn blade, loose blade jam nut, loose engine or lodged foreign objects.
Note: See maintenance section for proper blade jam nut torque specifications.
STARTING
STOP POSITION
ENGINE: See engine manufacturer’s instructions for
type and amount of oil and gasoline used. Engine must
be level when checking and filling oil and gasoline.
Fig. 1
ENGINE SPEED: Set at factory. The engine runs at a
constant speed.
1. Select desired cutting height before starting engine.
2. Place mower on a sidewalk or driveway where the
mower blade is in an unloaded condition. If it must be
started on the lawn, move mower over previously cut
grass.
OPERATING POSITION
3. Be sure drive lever (Yellow lever on the right hand side)
is not engaged (fig. 1).
4. Prime to choke. Prime is located in front of the engine.
5. Pull down on operator presence control lever (Red
lever on the left hand side - fig. 1.1), then pull back on
starter rope slowly until resistance is felt. Then pull cord
rapidly to start. Repeat if necessary.
Fig. 1.1
HANDLING & TRANSPORTING:
Using two people to lift machine is recommended. Lift holding the handle and front of deck. Secure in
place during transport.
Never lift the machine while the engine is running.
CUTTING OPERATION
CAUTION: The mower blade will be rotating whenever engine is running.
CAUTION: Shut down the engine when crossing gravel drives, walks or roads and under all conditions where
thrown objects might be a hazard.
CLEARING A CLOGGED CUTTING DECK: Turn engine off and wait for blade to stop completely. Disconnect
spark plug wire.
Wearing durable gloves, remove clog. Danger, the clog may contain sharp materials. Reconnect spark plug wire.
CAUTION: Use extreme care when operating the blade. Inspect the work area for foreign objects that could cause
damage to the unit or injure the operator if struck by the blade. Never operate the blade with bystanders in the work
area
CUTTING HEIGHT ADJUSTMENT
Fig. 2
CAUTION: DO NOT make cutting height adjustment when engine is running.
Cutting height can be adjusted from 2" to 4" by 1/2" increments by lowering or raising
the deck. For easiest adjustment change the height from one side at a time. To change
cutting height, remove lock pins, raise or lower deck to desired height, and then reinsert
lock pins. Repeat this step on other side NOTE: Be sure that the deck is level. Running
the deck out of level will result in poor cut quality and increased belt wear.
Part No 510267
Form No F052808A
9
HW Owner’s Manual
Fig. 3
Fig. 3.1
Fig. 4
Fig. 5
PROPULSION
This unit is self-propelled, and is controlled by a lever control. To
engage the wheel drive, pull up and squeeze it against operator's
handle. The drive is disengaged by releasing this lever.(See Fig. 3 &
3.1)
GROUND SPEED can be varied by selecting a higher or lower gear using
the gearshift lever on top of the handle (See Fig. 4). Under most conditions
cutting should be done in first or second gear. Third gear should be reserved
for conditions where weeds and brush are thinned out or not as tall. The
quality of the cut produced is directly related to the unit's ground speed
during cutting. If the quality of the cut is not satisfactory (i.e. material left
standing) you should shift into a lower gear during cutting. For improved
control in confined areas, this machine can be pushed forward or backward
by releasing the drive lever located at the right side of the handle.
HILLSIDE MOWING
WARNING! Never mow on any slope greater than 15 degrees. Always
mow across the face of slopes; never up and down or diagonally see fig 5).
DO NOT attempt sudden starts or stop when mowing on a slope. Avoid
sudden turns and use extreme caution when changing direction on a slope.
STORAGE
Never store engine indoors or in enclosed poorly ventilated areas with fuel in
tank, where fuel fumes may reach an open flame, spark or pilot light, as on a furnace,
water heater, clothes dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as follows:
Be sure engine is cool. Do not smoke. Remove all gasoline from carburetor and
fuel tank to prevent gum deposits from forming on these parts and causing possible
malfunction of engine. Drain fuel outdoors, into an approved container, away from
open flame. Run engine until fuel tank is empty and engine runs out of gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing the
formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank
or storage container. Always follow mix ratio found on stabilizer container. Run
engine at least 10 min. after adding stabilizer to allow it to reach the carburetor.
CAUTION: Wheels must be chocked or blocked when unit is parked on a slope.
Part No 510267
Form No F052808A
10
HW Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every Use (daily)
Every 5 hrs or (daily)
Every 25 Hours
Every 100 Hours
z
Inspect for loose, worn or damaged parts.
Check for excessive vibration
Inspect belt for wear
z
z
Engine (See Engine Manual)
Lubricate front wheels and height adjustment pins
Sharpen Blade
z
z
z
Replace blade and traction belts
BLADE Removal / Sharpening
NOTE: When sharpening the blade it is a good idea to check the balance of the blade. A
properly balanced blade will increase life of the bearings and other components.
Tools required: 3/8 inch socket, 5/8 inch socket, torque wrench, blade block.
1. Disconnect spark plug wire.
2. Remove 5 screws (item 76) then remove belt guard (19).
3. Set the unit on its side to allow access to both pulley and the blade.
Note: When tipping the unit on its side, keep the air cleaner side of engine up. Be sure the gas is
drained out to prevent from spilling before tipping the unit on its side. Never tip the mower more
than 90 degrees and do not leave the mower tipped for any length of time.
Fig. 6
4. While protecting your hands with pair of gloves or heavy rag to hold the blade, loosen but do not
remove the bolt (88) on the pulley side (fig. 6).
5. Remove jam nut (68), blade washer (43), blade (44), blade washer (43), and blade spacer (39).
6. Replace or sharpen the blade then install in the exact order they were removed (fig. 7).
7. Tighten the jam nut until it is flush with the end of the shaft (fig 7). Then tighten the bolt on
the pulley side - Torque it to 55-60 ft-lbs.
Note: When replacing the blade use B.G.I. Part no. 510107.
8. Reinstall belt guard then connect spark plug.
Note: Before installing the fasteners inspect them for wear and replace as necessary.
Fig. 7
BELT REPLACEMENT
When replacing one belt the other should be inspected for wear and replaced if worn. It
is good practice to change both belts when either is worn beyond use. Use only original
equipment belts for replacement. Billy Goat uses only premium quality, Kevlar corded
and coated belts in your unit. Substitute belts do not meet the design and performance
requirements for your unit, and will greatly reduce machine performance and belt life.
Blade Drive Belt
Tools required: 3/8 inch socket, 1/2 inch socket, 3/8" torque wrench.
1. Disconnect spark plug wire.
2. Set the deck height to middle position (3 inches cutting height).
3. Remove 5 screws (item 76) then remove belt guard (19).
4. Loosen but do not remove the nut (71) at the top of the engine base located just front of the
engine. This will release the tension on the blade drive belt (37). NOTE: It may be necessary to
loosen bolt (85) in order to allow idler pulley bracket to pivot.
5. Replace the old belt with the new belt.
Note: Use only O.E.M. approved belt for this machine - B.G.I. Part no. 510139.
6. To adjust tension on the new belt, insert 3/8" torque wrench in the idler bracket, apply 10 lbs.
of torque then tighten the nut (71) on top of the engine base (fig. 8).
Note: Belt requires very little tension to drive the blade. Over tensioning the belt will greatly
reduce the life of the belt.
7. Install belt guard using 5 screws (76)
8. Reconnect spark plug wire.
Note: Start the unit up and cut grass to make sure the blade belt is not slipping.
Nut (71)
Nut (85)
Fig. 8
Part No 510267
Form No F052808A
11
HW Owner’s Manual
BELT REPLACEMENT continued
Drive Belt
Tools required: 3/8 inch socket, 1/2 inch socket, 3/8" torque wrench.
1. Follow steps 1 through 5 above to remove the blade drive belt.
2. Set the unit on its side to allow access to both pulley and the blade.
Note: When tipping the unit on its side, keep the air cleaner side of
engine up. Be sure the gas is drained out to prevent from spilling before
tipping the unit on its side. Never tip the mower more than 90 degrees
and do not leave the mower tipped for any length of time.
3. Swing over the drive belt idler to release tension on drive belt then
remove it (fig. 9).
Fig. 9
4. Install the new belt (fig. 10).
Note: Use only O.E.M. approved belt for this machine - B.G.I. Part no.
510138.
5. Set the unit back down.
6. Follow steps 6 through 8 on previous section to reinstall the blade
belt.
Fig. 10
SELF PROPELLED DRIVE ADJUSTMENT
Tools required: two 1/2 wrenches.
As the clutch wears, adjustments may be required to maintain proper
control cable tension, and clutch engagement (fig. 11). If the clutch begins
slipping or squealing during normal operation it may require an adjustment
to increase the clutch cable tension. A properly adjusted drive clutch
should require a minimum of 3/8" of spring stretch when drive lever is
engaged (fig. 12). Adjust by tightening or by loosening clutch cable
adjusting nut as required, located at the clutch lever (fig. 12). If further
adjustment is required, primary adjuster is located at the underneath the
engine base (fig. 13). Replacement of cable may be necessary if
adjustment will not allow for proper drive clutch engagement.
Adjuster
Fig. 11
Fig. 12
Fig. 13
WARNING: If the drive clutch begins to squeal or slip, do not continue
to operate your unit until adequate adjustment or repair has been
performed. Improper adjustment can cause drive clutch to slip and
overheat, greatly reducing machine performance and transmission life.
3/8” stretch when
engaged
Part No 510267
Form No F052808A
12
HW Owner’s Manual
Troubleshooting
P ro b le m
P o s s ib le C a u s e
S o lu tio n
E n g in e w ill n o t s ta rt.
O p e ra to r p re s e n c e c o n tro l le v e r is n o t
e n g a g e d . E n g in e n o t p ro p e rly p rim e d . O u t o f
g a s o lin e , b a d o r o ld g a s . S p a rk p lu g w ire
E n g a g e o p e ra to r p re s e n c e c o n tro l le v e r.
P rim e to c h o k e . C h e c k G a s o lin e . C h e c k
fo r s p a rk w ith a n a p p ro v e d te s te r. C le a n
d is c o n n e c te d . D irty a ir c le a n e r. B la d e is try in g o r re p la c e a ir c le a n e r. S ta rt th e m o w e r
to c u t g ra s s w h ile s ta rtin g .
o n p a v e m e n t o r p re v io u s ly c u t a re a .
E n g in e w ill n o t s to p
E n g in e ru n s p o o rly
D a m a g e d o p e ra to r p re s e n c e c o n tro l le v e r.
D a m a g e d c o n tro l c a b le .
S p a rk p lu g lo o s e . E n g in e R P M s e t to o lo w .
W a te r o r d irt in fu e l s y s te m . S p a rk p lu g
fo u le d , fa u lty o r w ro n g g a p
R e p la c e o p e ra to r p re s e n c e c o n tro l le v e r.
R e p la c e c o n tro l c a b le
S h a rp e n o r re p la c e b la d e (p g 1 1 ). C h e c k
e n g in e R P M (re fe r to e n g in e m a n u a l).
D ra in o r s ip h o n th e n re p la c e w ith fre s h
g a s o lin e . R e s e t g a p o r re p la c e s p a rk
p lu g (re fe r to e n g in e m a n u a l).
A b n o rm a l v ib ra tio n .
· L o o s e o r o u t o f b a la n c e b la d e . B e n t b la d e .
L o o s e e n g in e b o lts
S to p w o rk im m e d ia te ly . C h e c k b la d e
m o u n t a n d b a la n c e . R e p la c e d a m a g e d
o r b e n t b la d e if re q u ire d (p g 1 1 ). C h e c k
e n g in e m o u n t.
U n e v e n c u t
H e ig h t a d ju s t is n o t s e t c o rre c tly . D u ll o r b e n t
b la d e
B e s u re h e ig h t a d ju s t is s e t th e s a m e o n
b o th s id e s (p g 9 ). S h a rp e n o r re p la c e
b la d e (p g 1 1 ).
W ill n o t c u t o r h a s p o o r
c u ttin g p e rfo rm a n c e
D u ll o r b e n t B la d e . C lo g g e d d e c k . W e t G ra s s . S h a rp e n o r re p la c e b la d e (p g 1 1 ).
E x c e s s iv e ly h ig h g ra s s .
U n c lo g d e c k (p g 9 ). C h e c k e n g in e R P M
(re fe r to e n g in e m a n u a l). D o n o t m o w
w h e n g ra s s is w e t. M o w o n c e a t a h ig h
c u tin g s e ttin g th e n m o w a g a in a t d e s ire d
s e ttin g o r m a k e a n a rro w e r c u ttin g p a th .
B e lt s lip s o r s m o k e s
N o s e lf p ro p e llin g
B e lt te n s io n to o lo w . B e lt w o rn o r s tre tc h e d .
P u lle y s w o rn o r d a m a g e d .
In c re a s e te n s io n a t id le r (p g 1 1 ). R e p la c e
b e lt. R e p la c e P u lle y s .
N o t s e t to g e a r. O u t o f a d ju s tm e n t c lu tc h
c a b le . B ro k e n c lu tc h c a b le . W o rn o r b ro k e n
b e lt.
S h ift le v e r to d e s ire d g e a r. A d ju s t c lu tc h
c a b le (p g 1 2 ). R e p la c e w ith n e w c a b le .
R e p la c e b e lt (p g 1 2 ).
S e lf p ro p e lle d d riv e w ill
n o t re le a s e .
C lu tc h c a b le o u t o f a d ju s tm e n t. D a m a g e d
o p e ra to r p re s e n c e c o n tro l le v e r.
A d ju s t c lu tc h c a b le (p g 1 2 ). R e p la c e
o p e ra to r p re s e n c e c o n tro l b a il.
E n g in e is lo c k e d , w ill n o t
p u ll o v e r.
D e b ris lo c k e d a g a in s t b la d e . O p e ra to r
p re s e n c e c o n tro l le v e r n o t e n g a g e d . B ro k e n
c o n tro l c a b le .
R e m o v e d e b ris (p g 9 ). E n g a g e d o p e ra to r
p re s e n c e c o n tro l le v e r (p g 9 ). R e p la c e
c o n tro l c a b le .
When servicing engine refer to specific manufacturers engine owner's manual. All engine warranty is covered by the specific engine
manufacturer. If your engine requires warranty or other repair work contact your local servicing engine dealer. When contacting a dealer
for service it is a good idea to have your engine model number available for reference (See table page 3). If you cannot locate a
servicing dealer in your area you can contact the manufacturers national service organization.
To reach:
American Honda: 800-426-7701
WARRANTY CLAIM PROCEDURE
®
Should a BILLY GOAT machine fail due to a defect in material and/or workmanship, the owner should make a warranty claim as
follows:
•
•
•
The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY GOAT Dealer.
The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their respective BILLY GOAT
Distributor for their territory Attention: Service Manager. Any parts replaced under warranty must be tagged and retained for 90
days. The model number and serial number of the unit must be stated in the Warranty Claim.
•
•
The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.
The Technical Service Department at BILLY GOAT will study the claim and may request parts to be returned for examination.
BILLY GOAT will notify their conclusions to the distributor service manager from whom the claim was received.
•
The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is final and binding.
For online product registration go to www.billygoat.com
Part No 510267
Form No F052808A
13
HW Owner’s Manual
PARTS DRAWING HW
5
2
79
7
69
5
4
6
87
8
78
71
96
100
96
78
96
TO TRANS SHIFT LEVER
10
62
112
10
9
TO DRIVE CLUTCH
63
76
92
11
48
TO ENGINE BRAKE/
KILL SWITCH
13
71
96
12
98
15
14
109
70
110
19
76
69
86
107
86
71
16
64
92
54
71
106
20
96
96
59
78
96
35
18
17
91
82
24
64
83
96
25
81
95
21
74
93
105
22
70
102
71
89
96
70
53
113
26
103
27
29
30
28
47
103
3
67
55
90
23
71
94
75
99
31
33
32
66
77
88
99
23
36
73
94
49
34
72
104
96
85
37
65
38
46
104
45
40
71
41
111
50
56
102
94
90
103
61
69
60
42
40
58
94
51
49
52
80
63
96
61
39
43
85
44
43
68
57
Part No 510267
Form No F052808A
14
HW Owner’s Manual
PARTS LIST
HW651SP
PART NO.
510263
510262
-
900407
510274
510127
510261
830533
510264
-
HW651HSP
ITEM
ITEM
NO.
1
2
3
4
5
6
7
HW651SP
PART NO.
510147
510207
510206
400424
830502
900327
400217
8024040
9201072
9201071
-
350155
8160001
8160003
8160002
8160007
8195166
8059136
500144
510208
400946
8041031
8041011
8041023
510188
8041058
8041052
500177
8041028
8024039
8041034
510213
400502
430298
8041054
510193
8143001
8177020
8171004
8171003
HW651HSP
PART NO.
510147
510207
510206
400424
830502
900327
400217
8024040
9201072
-
DESCRIPTION
QTY
QTY
DESCRIPTION
QTY
QTY
PART NO.
510263
510262
830113
900407
510274
510127
510261
830533
-
NO.
LEVER DRIVE CLUTCH W/CABLE
LEVER ENGINE BRAKE W/CABLE
SPACER 1" ID X 2" OD
TY WRAP
GRIP HANDLE 1” ID X 5” BLACK
CONTROL SHIFT 3 SPEED
HANDLE UPPER HW
ROPE GUIDE
ENGINE 6.0 HP KAWASAKI
ENGINE 6.5 HONDA OHV
1
1
-
3
2
1
1
2
1
-
1
1
1
3
2
1
1
2
-
58 LABEL CUTTING HEIGHT
59 LABEL INSTRUCTION
60 LABEL WARNING MOWER
61 LABEL OPEI
62 LABEL OIL CHAIN
63 LABEL DANGER GUARDS
64 SPRING TENSION
1
1
1
2
1
2
1
1
1
1
-
1
1
1
2
1
2
1
1
1
-
8
9
65 CARRIAGE BOLT 5/16”-18X1
66 KEY SQ 3/16 X 5/8”
510279
510265
510111
510120
510125
510126
510108
350146
8172005
8155007
510110
8154007
510269
8172011
440153
510268
900819
510144
510141
510137
-
510280
510199
510138
510122
510191
510136
510123
510118
510139
510114
500232
500101
510105
510116
510117
510107
510132
510104
510281
400268
510266
510197
510160
510130
350209
510247
510142
510205
350154
1
2
1
1
2
1
1
2
1
1
1
1
2
10
2
2
2
1
1
1
-
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
2
1
1
4
2
1
1
1
1
67 KEY SQ 3/16" X 1 1/4"
KEY SQ 1/4" X 1"
68 NUT JAM7/8” -14
69 NUT LOCK 1/4-20 HEX ZP
70 NUT LOCK 3/8-16
71 NUT LOCK 5/16
10 HANDLE LOWER HW
11 CHAIN GUARD HW
12 PLATE BEARING RIGHT
13 BEARING 1/2 CLIP
14 8 TOOTH SPROCKET
15 TRANSMISSION 3 SP
16 C-CLIP 1/2
17 WASHER #10 SAE
18 LOCK NUT #10
19 BELT GUARD HW
20 NUT #10 HEX
21 FRONT WHEEL BRACKET
22 WASHER 1/2” ZP
23 WASHER 1/2" - .453 ID
24 WHEEL FRONT 6"’
25 SPACER WHEEL FRONT
26 PLATE DEFLECTOR MOUNT
27 RUBBER DEFLECTOR
28 PULLEY IDLER
29 PULLEY DOUBLE 2”/4” W/INERTIA
PULLEY DOUBLE 2”/4” W/INERTIA-25MM
30 ARMIDLER TRANS WA HW
31 BELT 3L320
32 PULLEY 3” OD 10MMBORE
33 PLATE ENGINE IDLER WA HW
34 PULLEY IDLER
35 BRACKET TRANS LEVER
36 PULLEY 5.5” OD X 7/8” BORE
37 BELT BLADE 5L560
38 SHAFT DRIVE BLADE
39 SPACER SPINDLE BC2401
40 BEARING 7/8” SEALED
41 SPINDLE BLADE WA HW
42 TUBE SPACER SPINDLE
43 WASHER SPINDLE 2.5 OD
44 BLADE 23 1/2 W7/8 HOLE
45 CHAIN #41 75 PITCH
46 REAR AXLE ASSY
510265
510111
510120
510125
510126
510108
350146
8172005
8155007
510110
8154007
510269
8172011
440153
510268
900819
510144
510141
510137
510237
-
510199
510138
510122
510191
510136
510123
510118
510139
510114
500232
500101
510105
510116
510117
510107
510132
510104
-
2
1
1
2
1
1
2
1
1
1
1
2
10
2
2
2
1
1
1
1
-
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
-
9201113
350155
8160001
8160003
8160002
8160007
8195166
8059136
500144
510208
400946
8041031
8041011
8041023
510188
8041058
8041052
500177
8041028
8024039
8041034
510213
400502
430298
8041054
510193
8143001
8177020
8171004
8171003
1
1
3
7
20
1
1
1
1
8
1
7
1
1
3
2
4
1
5
5
1
1
4
2
4
8
1
2
4
32
1
3
7
20
1
1
1
1
8
1
7
1
1
3
2
4
1
5
5
1
1
4
2
4
8
1
2
4
32
72 NUT LOCK 5/8-11
73 ROLL PIN 3/16 X 1.25
74 SCREW MACHINE #10-24X 3/4
75 BOLT SHOULDER 1/2” X 1”
76 SCREW SELF TAP 1/4 X 3/4”
77 SCREW CAP 3/8-24 X 1 1/4”
78 SCREW CAP 5/16”-18X1 3/4
79 SCREW CAP 1/4-20 X 2 1/4”
80 SCREW CAP 1/4-20 X 7” ZP
81 SCREW SELF TAP 6 X 16
82 SCREWCAP 3/8-16 X 3”
83 SCREWCAP 3/8-16 X 1 1/2”
84 LABEL CLUTCH BLADE
85 SCREWCAP 5/16-18 X 1”
86 CARRIAGE BOLT 5/16-18X3/4
87 SCREWCAP 5/16-18 X 2 1/2”
88 SCREWCAP 7/16-20 X 1 1/4 GR8
89 TWISTED WASHER 3/8”
90 TWISTED WASHER 5/16”
91 SCREW CAP 3/8-16 X2
92 WASHER 1/4 SAE BLACK
93 NUT JAM1/4 - 20
94 WASHER 3/4 SAE
95 WASHER 3/8 FC
96 WASHER 5/16 FC
97
98 KEY WOODWRUFF 1/8 X 1/2
99 WASHER LOCK 3/8 S/T MED
100 RUBBER GROMMET
101 LABEL CLUTCH DRIVE
102 SPACER NYLON BUSHING
103 SCREWCAP 5/16-18 X 1 1/2
104 KEY SQ. 3/16 X 2 1/8”
105 SCREW CAP 1/4-20 X 1 1/4
106 WASHER 1/4 SAE
510180
8177012
520087
500176
520045
8041030
9201087
8041007
8172007
510255
1
2
1
1
2
3
2
1
1
4
510180
8177012
520087
500176
520045
8041030
9201087
8041007
8172007
510255
1
2
1
1
2
3
2
1
1
4
47 SPACER HWHONDA
48 LABEL DO NOT FILL
49 WHEEL SPOKE 16”
50 GUARD EXHAUST CHUTE
51 DECK ASSY W/LABELS
52 PIN 3/8X 1 1/2
53 BEARING 3/4 CAST FLANGE
54 BASE ASY W/LABELS
55 SPRING TRANS IDLER
56 SPRING EXHAUST CHUTE
57 WASHER LOCK 7/8 INT TOOTH
400268
510266
510197
510160
510130
350209
510247
510142
510205
350154
1
2
1
1
4
2
1
1
1
1
107 SCREW 3/8 X 1 TAPTITE
108
109 LABEL READ MANUAL
110 LABEL EAR EYE BREATHING
111 LABEL FLYING DEBRIS
112 GROMMET 1” HOLE
113 NUT LOCK 3/8-16 THIN
890301
890254
810736
510169
8161042
1
1
1
1
4
890301
890254
810736
510169
8161042
1
1
1
1
4
Part No 510267
Form No F052808A
15
HW Owner’s Manual
MAINTENANCE RECORD
Date
Service Performed
Part No 510267
Form No F052808A
16
|