1
R
Patent Pending
T h a n k Yo u fo r S e l e c t i n g
The Powerful
TM
EZ AIR AERATOR
Operator Owner's Manual
AE550, AE550H
3
Specifications
AE550
AE550H
ENGINE: H.P.
ENGINE: TYPE
5.5 (4.1 kW)
5.5 (4.1 kW)
B&S OHV
HONDA OHV
ENGINE: FUEL CAP.
ENGINE: OIL CAP.
UNIT WEIGHT
3.0 qt. (2.84 L)
0.66 qt. (0.62 L)
290# (131.8 kg)
36# (16.4 kg)
326# (148.2 kg)
447# (203.2 kg)
3.88 qt. (3.41 L)
0.69 qt. (0.65 L)
294# (133.6 kg)
36# (16.4 kg)
REMOVABLE WEIGHT
NET UNIT WEIGHT
WEIGHT: SHIPPING
330# (150.0 kg)
451# (205.0 kg)
Page 1 of 12
Part No. 360178
Form No. F012302A
Download from Www.Somanuals.com. All Manuals Search And Download.
9
GENERAL SAFETY
For your safety and the safety of others, these directions should be followed:
Do not operate this machine without first reading
owner's manual and engine manufacturer's manual. ·DO NOT operate a machine that exhibits excessive vibration.
·DO NOT operate this machine on slopes greater than 19°.
·DO NOT use this unit on any surface other than grass lawns.
·DO NOT allow children to operate this equipment.
Use of Ear Protection is recommended while
operating this machine.
Use of Eye and Breathing protection is recommended
when using this machine, especially in dry and dusty
conditions.
-DO read all maintenance and operating instructions before
begining work.
-DO read all engine manufacturers operating and maintenance
instructions.
Wearing gloves is recommended while
operating this machine.
-DO inspect lawn before begining work. Remove all rocks, wire,
string, or other objects that can present a hazard during work prior to
starting.
-DO identify and mark all fixed objects to be avoided during work,
such as sprinkler heads, water valves, buried cables, or clothes line
anchors, etc.
·DO NOT place hands or feet underneath unit, near debris
outlet or near any moving parts.
·DO NOT start engine without tine height adjust lever in up
position and clutch bail disengaged.
·DO NOT start or operate machine with guards removed.
·DO NOT perform any service on the unit without removing
the spark plug wire.
10
ASSEMBLY
3. SECURE the upper handle by positioning the lowermost mounting hole
over the chosen handle mounting stud and tightening the hand knob on
the handle pivot bolt to secure the handle in position.
Read all safety and operating instructions
before assembling or starting this unit.
4. REPLACE the lock nuts that were removed in step one and fully
tighten them to complete securing the handle in place.
PUT OIL IN ENGINE BEFORE STARTING
5.ATTACH the lift rods, one on each side of the unit. Remove the hair
pins that are shipped in free end of the rods. Pivot the rods up and along
the side of the unit and slip the free end of the rod into the lift link bars
one on each side of the unit. With the rods in position, replace the hair
pins in the holes that they were removed from to lock the lift rods in
place.
5. CHECK engine oil level and fill to proper level. See engine owners
manual for type and amount of oil to use. Move the tine height adjust
lever to the down position, to level engine during checking.
6.CONNECT spark plug wire.HONDA ONLY:Set the engine stop switch
to the on position. You will use the stop switch on the handle during
operation.
Your Billy Goat EZ-Air aerator is shipped from the factory in one
carton, completely assembled.
1.REMOVE lock nuts from the upper handle mounting stud. These
will be reused.
2. UNFOLD the upper handle and pivot it back into the operating
position. NOTE:There are two height positions that the handle can
be set in. The lower stud places the handle in the highest position
the upper stud places the handle in the lowest operating position.
11
PACKING CHECKLIST
These items should be included in your carton. If any
of these parts are missing, contact your dealer.
Per Model
Check
Check
Briggs & Stratton
5.5 Intek OHV
Engine
Manual Per
Model
Honda 5.5 OHV
Check
Owner's
Manual
360178
Literature
Assembly
360177
Check
Check
Warranty
Card 400972
EU Declaration
of Conformity &
EU Distributor
List 360194
Page 3 of 12
Part No. 360178
Form No. F012302A
Download from Www.Somanuals.com. All Manuals Search And Download.
13
CONTROLS
HONDA ENGINE THROTTLE CONTROL
B & S ENGINE THROTTLE CONTROL
Set lever to choke position when
starting a cold engine
THROTTLE LEVER
RUN
CHOKE
STOP
Set lever to desired engine speed.
Move lever completely to the left
to stop engine
15
ENGINE LABELS
FUEL VALVE
CHOKE LEVER
Briggs & Stratton
RUN
CHOKE
ON
14
INSTRUCTION LABELS
OFF
These labels should be included on your Aerator. If any of
these labels are damaged, replace them before putting this
equipment into operation. Item and part numbers are given to
help in ordering replacement labels.
THIS ENGINE EQUIPPED WITH
LOW OIL SENSOR, IF ENGINE WILL
NOT START, CHECK OIL LEVEL
Label Danger
Keep Hands
and Feet Away
Part No.400424
WARNING
EXPLOSIVE FUEL
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
..
WARNING
Label Do Not Fill While
Engine Is Hot
Part No.400268
Read and follow Operating
Instructions before running engine.
Gasoline is flammable. Allow engine
to cool at least 2 minutes before fueling.
Engines emit carbon monoxide,
DO NOT run in enclosed area.
WARNING
LIFT HERE
Honda
THE UNIT WEIGHS OVER 300 LBS.
LIFT HERE WITH CAUTION
Label Warning Unit Weight
Part No.360188
Label LIFT HERE ARE
Part No.360187
WARNING
Label Danger Guard
Part No.900327
OPERATING INSTRUCTIONS
BEFORE STARTING, MAKE SURE:
TINE DEPTH CONTROL BAIL IS IN UP POSITION.
ALL GUARDS ARE ATTACHED.
TO START, MOVE ENGINE STOP SWITCH TO "ON" AND PULL ROPE.
NOTE: IT MAY BE NECESSARY TO USE THE ENGINE CHOKE IF
ꢀ
ꢀꢀꢀ
ENGINE IS COLD.
PUSH FORWARD ON TINE LIFT HANDLE TO ENGAGE TINES
IN GROUND.
PUSH FORWARD ON OPERATOR'S BAIL TO ENGAGE DRIVE AND
START AERATING.
DURING OPERATION PUSHING DOWN ON OPERATOR'S HANDLE
WILL MAXIMIZE CORING DEPTH.
RELEASE BAIL TO STOP UNIT.
FOR PREVENTATIVE MAINTENANCE
CHECK ENGINE OIL DAILY.
INSPECT AND CLEAN ENGINE AIR FILTER DAILY.
REPLACE AS NEEDED.
GREASE ALL BEARINGS AND CHECK GEAR REDUCTION
OIL LEVEL ON EVERY ENGINE OIL CHANGE.
OIL ALERT
READ OWNERS MANUAL
BEFORE OPERATING
ꢀ
NOTE: ENGINE WILL CONTINUE TO RUN WITH BAIL DISENGAGED.
ALWAYS:
TO TURN UNIT, PULL BACK ON TINE LIFT HANDLE TO LIFT TINES
OUT OF GROUND. GRADUAL TURNS CAN BE MADE WITHOUT
LIFTING THE TINES.
WITH TINES UP, PUSH FORWARD ON OPERATOR'S BAIL TO
ENGAGE WHEELDRIVE FOR ASSISTED TURNING.
TO STOP ENGINE MOVE ENGINE STOP SWITCH TO "OFF".
INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY
WORN AND DAMAGED PARTS.
PROPERLY SECURE EQUIPMENT BEFORE TRANSPORTING.
DISCONNECT SPARK PLUG WIRE BEFORE SERVICING UNIT.
USE ONLY A QUALIFIED MECHANIC TO SERVICE THIS MACHINE.
WHEN OIL LEVEL LOW,
USE PERSONAL
PROTECTION EQUIPMENT
ENGINE STOPS IMMEDIATELY.
Label Instructions Height Adjust - Part No. 350224
Part No. 360178
Form No. F012302A
Page 4 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Operation
INTENDED USE: This machine is designed for aerating
established lawns and large grass covered areas. The
machine should not be used for any other purpose than
that stated above.
TINES RAISING/LOWERING
The tines are raised or lowered into the ground by operating
the tine engagement lever on the upper handle. Tine
penetration is very dependent on surface preparation. READ
the operation section before aerating.
DO NOT operate if excessive vibration occurs. If excessive
vibration occurs, shut engine off immediately and check for
damaged or worn tine reel, loose pulley bolts or set screws,
loose engine or lodged foreign objects. (See trouble
shooting section on page 12).
TINES UP
TRANSPORT
Like all mechanical tools, reasonable care must
be used when operating machine.
Inspect machine work area and machine before operat-
ing. Make sure that all operators of this equipment are
trained in general machine use and safety.
STARTING ENGINE
ENGINE: See engine manufacturer’s instructions
for type and amount of oil and gasoline used.
Engine must be level when checking and filling oil and
gasoline.
TINES DOWN
RUNNING
GEAR REDUCTION: See engine manufacturer’s instruc-
tions for type and amount of oil used. Engine must be level
when checking and filling the gear reduction case. The
engine is shipped from the factory with oil in the gear case.
It shoudl be checked before first use.
AERATING OPERATION
DO NOT- Use this machine on any surface other than a lawn or
similar area.
DO NOT- Use this machine on slopes in excess of 19°.
DO NOT- Allow persons unfamiliar with this equipment to operate it.
DO NOT- Allow children to operate this equipment.
ENGINE SPEED: Controlled by throttle lever on the upper
handle. Under normal conditions, operate at the minimum
throttle speed to accomplish your task.
NOTE: The unit ground speed varies with the engine speed.
FUEL VALVE: Move fuel valve to "ON" position
Honda: Located below the air cleaner on the engine.
Briggs: Located on face of the engine.
MOW: Mow the lawn to it's normal cut height.
WATER: For the best performance and maximum tine
penetration the lawn should be thoroughly watered the day
before aeration.
ENGINE STOP SWITCH: Move to "ON" position
Honda only: Located on side of engine. During normal
operation use the remote stop switch on the operators
handle.
INSPECT lawn before begining work. Remove all rocks, wire,
string, or other objects that can present a hazard during work
prior to starting.
IDENTIFY and mark all fixed objects to be avoided during
work, such as sprinkler heads, water valves, buried cables, or
clothes line anchors, etc.
CHOKE: Engage the choke when starting a cold engine.
Honda: Located below the air cleaner on the engine.
Briggs: Located on top of the air cleaner on the engine.
START ENGINE: See above.
THROTTLE: Move the throttle control on the upper handle
to fast position. Pull starting rope to start engine.
SET SPEED: The ground speed of your aerator varies with
the engine speed. Set the engine at approximately half
throttle to start. Speed may be increased based on the turf
conditions (i.e. large flat areas) and operator experience.
Speed should be lowered when operating under adverse turf
conditions (i.e. fenced areas, hills, or slopes).
IFYOUR UNIT FAILSTO START:
See Troubleshooting on page 12.
NOTE: Honda engines are equiped with a low oil sensor to
prevent engine damage. When it senses a low oil condition
(i.e. unit is operating or sitting on a steep slope) the engine
shuts down. The low oil condition must be corrected before
the engine can be restarted. See the engine owners
manual for more information.
MOVE: Be sure the tine engagement control is in the up
position (tines out of the ground) and engage the wheel drive
by squeezing the operators clutch bail against the handle.
Transport the aerator to the work area.
Page 5 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 360178
Form No. F012302A
16
OPERATION continued
AERATOR OPERATION CON'T
!
s
t
AERATING TIPS
n
i
H
ENGAGE TINES: With the aerator in the work area, release
the clutch bail and push forward on the tine engagement
lever, lowering the tines into the dirt.
WATER: For the best performance and maximum tine
penetration the lawn should be thoroughly watered the day
before aeration.
SLOPES: Do not operate the aerator on steep slopes. Use
extreme caution when operating on any sloped surface.
For lesser sloped areas operate the unit, traversing up and
down at a 45 degree angle to the slope rather than straight
across. Extended operation on steep slopes can cause
engine damage.
AERATE: Engage the operators clutch bail by pushing it
forward to the handle, and start aerating.
NOTE: For maximum tine penetration apply downward
pressure on the handle.
TURNING: At the end of an aerating run, release the clutch
bail and pull back on the tine engagement control to lift the
tines out of the ground. Using the handle swivel the rear of
the unit to bring it around and line up for the next pass.
NOTE: Engage the clutch bail to use the front wheel drive to
aid in turning the unit.
NOTE: DO NOT release the operators clutch bail when
operating on a slope. This will allow the unit to free wheel
and allow the unit to roll down the slope.
NOTE: Honda engines are equiped with a low oil sensor to
prevent engine damage. When it senses a low oil condition
(i.e. unit is operating or sitting on a steep slope) the engine
shuts down. The low oil condition must be corrected before
the engine can be restarted. See the engine owners
manual for more information.
TRANSPORT: Be sure to lift the tine engagement lever (tine
out of the ground) before transporting away from the work
area.
HANDLING & TRANSPORTING
CAUTION: This unit is heavy. It requires at least two people to lift it.
TINE PENETRATION: Maximum tine penetration is
achieved by applying downward pressure on the handle
during operation.
REMOVE: The aerator is equiped with a removable rear weight.
Remove the weight when loading and unloading the unit. The weight
can be removed by rotating the locking tabs on the weight mounting
pins and lifting it straight up. See Fig. 1 below.
NOTE: The removable weight is also heavy and should handled
carefully and secured in place during transport.
TURNING: At the end of a pass the tines can be lifted out of
the ground to turn by lifting straight up on the operators
handle.
LIFTING: The aerator is equiped with lift handles. After removing the
weight lift the unit with two people one on each side of the unit. Grip
the unit at the points marked "LIFT HERE" when lifting. Lift using
your legs and not your back. See Fig. 2
USING RAMPS: Use ramps that are of adequate strength for a unit
of this weight. When loading the aerator using ramps be sure the
ramp is not too steep and that the surface of the ramp provides good
traction.
Fig. 1
Fig. 2
Part No. 360178
Form No. F012302A
Page 6 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
16
OPERATION continued
ADJUSTING HANDLE HEIGHT
UNIT STORAGE
This unit is equipped with a height adjustable upper handle to allow
for multiple operator heights.
TO ADJUST THE HANDLE HEIGHT:
Never store engine indoors or in enclosed poorly ventilated areas
with fuel in tank, where fuel fumes may reach an open flame, spark or
pilot light, as on a furnace, water heater, clothes dryer or other gas
appliance.
1. Remove the lock nuts (item 50) that secure the handle, one on
each side, to the lower handle mounting studs. See Fig. 1
2. Loosen the handle mounting knobs (item 51), one on each side,
(See Fig. 3) and push the handle out and away from the lower
handle mounting studs.
3. The handle is now free to rotate. Adjust the handle to the
desired height. The BOTTOM handle mounting stud coresponds
with the highest handle position. The TOP handle mounting stud
coresponds with the lowest handle mounting position.
4. Completely tighten the handle mounting knobs (item 51), and
replace the lock nuts (item 50) to secure the handle in place.
If engine is to be unused for 30 days or more, prepare as follows:
Remove all gasoline from carburetor and fuel tank to prevent
gum deposits from forming on these parts and causing possible
malfunction of engine. Drain fuel outdoors, into an approved
container, away from open flame. Be sure engine is cool. Do not
smoke. Run engine until fuel tank is empty and engine runs out of
gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing
the formation of fuel gum deposits during storage. Add stabilizer to gasoline in
fuel tank or storage container. Always follow mix ratio found on stabilizer
container. Run engine at least 10 min. after adding stabilizer to allow it to reach
the carburetor.
FOLDING HANDLE
PARKING
This unit is equipped with a folding upper handle for easier storage.
TO FOLD THE HANDLE:
1. Remove the lock nuts that secure the handle, one on each side,
to the lower handle mounting studs. See Fig. 1
2. Remove the hair pins that secure the tine lift rods, one on each
side, to the tine lift links. See Fig. 2
NEVER PARKTHIS UNIT ON A SLOPE OF ANY KIND.
Always keep tines in the up position when parking the unit.
3. Slide the rods out of the lift links and replace the pins in the holes
they were removed from for storage.
4. Rotate the lift rods down and back until they and hanging down
and to the rear of the unit.
5. Loosen the handle mounting knobs, one on each side, (Fig. 3)
and push the handle out and away from the lower handle mounting
studs.
6. The handle is now free to rotate. Rotate it up and toward the
front of the unit while holding the tine engagement control lever
against the rear of the upper handle. The handle will rotate into a
position with the top of the handle hooking over the front bumper of
the unit.
NOTE: Replace the lock nuts (item 50) on the lower handle
mounting studs for storage.
Fig. 2
Fig. 1
Fig. 3
Page 7 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 360178
Form No. F012302A
WING
SDRA
T
R
A
P
,AE50H
Part No. 360178
Form No. F012302A
Page 8 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 360178
Form No. F012302A
Page 9 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
17
MAINTENANCE
TINE REEL REMOVAL ANDTINE ROW REPLACEMENT
Use only a qualified mechanic for
any adjustments, disassembly or
any kind of repair .
TINE REEL REMOVAL
NOTE:Tine reel removal is only necessary to replace an entire
tine row or for other major unit maintenance. Individual tines
can be replaced by following theTINE REPLACEMENT instruc-
tions.
1. Wait for engine to cool and disconnect spark plug.
2. Remove the top guard by removing the four screws, two on each
side, that secure it to the frame.
WARNING: TO AVOID PERSONAL INJURY, ALWAYS
TURN MACHINE OFF, MAKE SURE ALL MOVING
PARTS COMETO A COMPLETE STOP.
DISCONNECT SPARK PLUGWIRE
BEFORE SERVICING UNIT.
3. Release the tension on the chain. See CHAINTENSION ADJUST-
MENT in this manual.
4. Remove the four bolts and nuts, two on each side, holding the tine
reel bearings in place. BE CAREFUL the tine reel is heavy and
sharp. Take precautions to not allow it to fall when the bearing bolts
are removed.
ENGINE: See engine manufacturer's
service instructions.
5. Lift the reel up and to the side to remove it from the drive chain.
6.SeeTINE ROW REPLACEMENT for instructions on maintenance.
7.To reinstall the reel follow the above steps in reverse.
8. Replace the guard and reinstall the four screws that secure it in
place.
REPLACE ALL GUARDS,BEFORE
STARTING ENGINE.
USE ONLY BILLY GOAT ORIGINAL
EQUIPMENT PARTS FOR
REPLACEMENT AND REPAIR
TINE ROW REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Remove the top guard by removing the four screws, two on each
side, that secure it to the frame.
3. Remove the tine reel per theTINE REEL REMOVAL instructions.
4. Remove the nut at the end of the tine reel shaft that secures the
tine rows in place.
TINE ROW KIT 360197
5. Remove the tine rows and spacers as necessary to replace the
defective part. Be sure to note the order in which the spacers were
removed for later reassembly.
6. Reassemble the tine reel in the exact order that it was disas-
sembled.
Complete tine row set for
replacement of one
complete row of tines.
Includes mounting
plates, spacer, and all
hardware.
7.Tighten the nut that secures the tine rows and spacers on the
shaft. Torque the nut to a minimum of 60 ft.lbs. Check that all of the
tine rows are tight by attempting to move them by hand.
8.Reinstall the tine reel per theTINE REEL REMOVAL instructions
above.
9. Re set the tension on the chain.
10. Replace the guard and reinstall the four screws that secure it in
place.
REPLACING INDIVIDUAL TINES
TINE KIT 360100
1. Wait for engine to cool and disconnect spark plug.
2. Loosen but do not remove the outermost nut and carraige bolt that
secure the damaged or worn tine.
3. Loosen and remove the innermost nut and carraige bolt that hold
the tine in the reel.
4. Use a small prybar and push the tine plates apart slightly to slide
out the tine to be replaced.
5. Slide the new tine in place and secure with the innermost nut and
carraige bolt. Tighten completely.
Individual coring tine for
replacement of worn or
broken tines.
6. Retighten the outermost nut and carraige bolt to completely secure
the new tine.
7. Repeat as required to replace all damaged or worn tines.
NOTE:Tines are a normal wear item and should be inspected
regularly for signs of wear or damage.
!
!
!
p
i
T
Spraying tines with a rust preventing lubricant can
increase tine life and allow for easier replacement of worn
or damaged tines.
Part No. 360178
Page 10 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Form No. F012302A
17
MAINTENANCE
BELT AND CHAIN TENSION ADJUSTMENT
DRIVE BELT REPLACEMENT
ADJUSTING BELT TENSION-
1. Remove the top guard (item 3) by removing the four screws (item
13), two on each side, that secure it to the frame.
1. Wait for engine to cool and disconnect spark plug.
2. Remove the top guard by removing the four screws, two on each
side, that secure it to the frame.
3. Slide the belt off of the engine drive pulley, and off of the jackshaft
drive pulley.
4. Continue sliding the belt along the jackshaft to the right jackshaft
bearing away from the pulley and sprockets.
5. Using a 9/16" wrench, remove the two bolts and nuts that hold the
jackshaft bearing in place.
6. Carefully lift the jackshaft up until the belt can be slid out underneath
the bearing.
7. Slide the new belt in place over the jackshaft.
8. Replace and tighten the bolts and nuts holding the jackshaft bearing
in place. Be sure that the jackshaft is aligned straight across between
both bearings.
9. Slide the belt along the jackshaft and over both engine and jackshaft
pulleys. Be sure the idler pulley is positioned on the flat side of the belt.
10. Check proper belt tension. See BELTTENSION ADJUSTMENT in
this manual.
2. Locate the top of the belt idler assembly where the clutch cable (item
55) is secured in place. A properly tensioned belt should stretch the
idler spring (loacted next to the idler pulley) between 1/4" - 3/8" when
the clutch bail (item 54) is held in the drive position.
3. Using a 1/2" wrench loosen the two nuts that secure the cable (item
55) in place.
4.TO INCREASE belt tension adjust these two nuts so that the cable
(item 55) is secured in place with an additional 1/4" of the threaded
adjuster at the top of the assembly.
TO DECREASE belt tension adjust these two nuts so that the cable
(item 55) is secured in place with 1/4" less of the threaded adjuster at
the top of the assembly.
5. Replace the guard (item 3) and reinstall the four screws (item 13) that
secure it in place.
6. Run the unit to test your adjustment. Repeat as necessary to
achieve proper adjustment. A properly adjusted belt will pull the unit up
a 15 degree slope when clutched without any belt slip, and will declutch
and stop the unit completely when the clutch is released.
CHAIN REPLACEMENT
NOTE:Never release the clutch on a slope. The unit is heavy and will
free wheel down hill.
NOTE:This procedure will work to change the wheel drive chain
or the tine drive chain.
1. Wait for engine to cool and disconnect spark plug.
2. Remove the top guard by removing the four screws, two on each
side, that secure it to the frame.
NOTE: A worn belt will not allow for proper adjustment and must be
replaced.
3. Roll the unit until the master link of the chain that you want to repalce
is exposed near the jackshaft sprocket.
4. Release the tension on the chain. See CHAINTENSION ADJUST-
MENT in this manual.
5. Using a screwdriver or similar device remove the spring clip that
secures the master link in the chain.
6. With the master link removed unwind the chain from the two sprock-
ets that it connects.
7. Carefully string the replacement chain around the same two sprock-
ets and reconnect it with the new master link provided with your
replacement chain.
8. Re set the tension on the chain.
9. Replace the guard and reinstall the four screws that secure it in
place.
ADJUSTING CHAIN TENSION-
1. Remove the top guard (item 3) by removing the four screws (item
13), two on each side, that secure it to the frame.
2. Locate the bolt (item 31, 33) and nut (item 80) that hold each idler
sprocket to the frame of the unit. One idler sprocket sets tension on the
wheel drive chain and one sets tension on the tine drive chain.
3. Loosen the bolt and nut and slide the idler sprocket (item 29) in the
desired direction.
INCREASEDTENSION:Slide the sprocket to the rear.
DECREASEDTENSION:Slide the idler sprocket to the front.
4.Tighten the bolt and nut to secure the sprocket in place.
5. Replace the guard and reinstall the four screws that secure it in
place.
NOTE: Over tensioning the chain will cause premature chain and
sprocket wear. DO NOT OVERTENSION THE CHAIN.A properly
tensioned chain will have slack of 1/4"-3/8" when moved by hand.
Follow these hourly
maintenance intervals.
Maintenance Schedule
Every
25 hrs
Every Use
(Daily)
Maintenance Operation
Engine (See Engine Manual)
Check engine oil
Check gear reduction oil level
Grease bearings (See Lubrication)
Oil chains (See Lubrication)
Inspect for loose, worn,
or damaged parts
Throughly clean all debris from unit
and tine reel.
Inspect belt
Lubricate caster rigs
Part No. 360178
Page 11 of 12
Form No. F012302A
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Before Requesting Service Review These Suggestions
Possible Cause
TROUBLESHOOTING
Solution
Problem
Working on too steep a slope.
Engine stalls or labors when raking.
Abnormal vibration.
Work at 45 degrees to the slop moving up and down
instead of across.
Damaged or missing tines. Loose handle bolts. Loose
engine bolts
Stop work immediately. Replace any damaged or
missing tines. Tighten all loose bolts and nuts.
Engine will not start.
Stop switch off (Honda only). Throttle in off position.
Engine not in full choke position. Out of gasoline. Bad
Check stop switches, throttle, choke position and
gasoline. Connect spark plug wire. Clean or replace
or old gasoline. Spark Plug wire disconnected. Dirty air air cleaner. Check and fill engine oil. Contact a
cleaner. Engine oil level too low (Honda only).
qualified service person.
Engine is locked, will not
pull over.
Debris locked against reel, or drive pulleys. Engine
problem.
Pull spark plug wire and remove debris. Contact an
engine servicing dealer for engine problems.
Engine is making loud noise or squealing.
Gear reduction oil level is low.
Check and add oil according to engine owners manual.
Unit does not move when
clutch is engaged.
Belt drive out of adjustment. Work drive belt.
Loose or damaged chain or sprockets. Loose or
damaged pulleys. Damaged or broken clutch cable.
See maintenance on page 7 of this manual. Contact a
qualified servicing dealer.
LUBRICATION
BEARINGS-
1. Remove the top guard by removing the four screws, two on each
side, that secure it to the frame. NOTE: Guard must be removed to
lubricate the jackshaft bearings only. All other bearings can be lubed
without removing the guard.
ENGINE
GOVERNED RPM
3600
ENGINE
MODEL NO.
HORSEPOWER
5.5
BRIGGS &
STRATTON
127452-0049-E1
HONDA
5.5
GX160K1HX2
3600
2. Lubricate all 6 bearings using a pressurized grease gun with a
standard lithium based grease.
3. Wipe any excess grease off of all bearings and fittings after each
lubrication.
4. Replace the guard and reinstall the four screws that secure it in
place.
When servicing the engine refer to specific manufacturers engine
owner's manual. All engine warranty is covered by the specific engine
manufacturer. If your engine requires warranty or other repair work
contact your local servicing engine dealer. When contacting a dealer
for service it is a good idea to have your engine model number
available for reference(See table page above). If you can not locate a
servicing dealer in your area you can contact the manufacturers
national service organization.
CHAINS-
1. Remove the top guard by removing the four screws, two on each
side, that secure it to the frame.
2. Apply a light coat of No. 30 Oil or a penetraing chain lubricant to keep
the chain clean and in good running order.
3. Replace the guard and reinstall the four screws that secure it in
place.
To contact:
Briggs & Stratton: 800-233-3723
American Honda: 800-426-7701
CASTERS-
1. Lubricate both caster rig bearings using a pressurized grease gun
with a standard lithium based grease.
2. Wipe any excess grease off of all bearings and fittings after each
lubrication.
Engine Service and Warranty
Contact your nearest engine manufacturer's
authorized servicing dealer. (See above)
WARRANTY PROCEDURE
22.1
22
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
Record your machine model, serial number and
date-of-purchase and where purchased
Serial Plate
21
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
1803 S. Jefferson
Lee's Summit,
MO 64062 / USA
Tel (816) 524-9666
Fax (816) 524-6983
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
R
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
Model
Serial No.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Unit(Weight)
lbs.
Engine Power
kW
101 dB
kg
rpm
min-1
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON / LEE'S SUMMIT, MO 64082-2312 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
Purchased
from
Purchase
Date
R
Page 12 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 360178
Form No. F012302A
|