Accessory
Application
Publications No.
All 21624
2001 ACCORD
2- AND 4-DOOR
(INCLUDES V6)
INSTALLATION
INSTRUCTIONS
SECURITY SYSTEM
Issue Date
AUG 2000
PARTS LIST
Security System Attachment (sold separately):
P/N 08E55-S84-100
Security System (sold separately):
P/N 08E51-S84-100
Security system
wire harness
2 Remote controls
Control unit
Sub-harness
LED
White connector clip
Control unit bracket
Push nut
2-Pin connector (for LED)
2 Relay brackets
5 Short wire ties
Disarm switch
Window decal
3-Pin connector
(for disarm switch)
3 Washer bolts, 6 x 1
Ground bolt
Nut, 12 mm
Washer
Owner’s Manual
3 Flange nuts, 6 mm
3 Self-tapping screw
2 Washer-screws, 4 x 30 mm
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
Y0581-A
1 of 12
08E55-S84-1000-91
Adjusting the Control Unit
INSTALLATION
•
Use a small flat-tip screwdriver to change the
mode switch and the horn/siren switch and to
adjust sensitivity.
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your car. These procedures should not
be attempted by "do-it-yourselfers."
GLASS BREAKAGE
SENSOR
MODE SWITCH
1. Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
AUTO LOCK
AUTO
MANUAL
SENSITIVITY
ADJUSTMENT
KNOB
2. Disconnect the negative cable from the battery.
3. Inside the passenger’s compartment, remove the
MAX
MIN
front console lower cover (four retaining clips).
SIREN
HORN
HORN/SIREN
SWITCH
FRONT CONSOLE
LOWER COVER
Mode Switch:
•
Set the mode switch according to the customer’s
CLIP
choice.
If the vehicle you’re working on is equipped with an
optional ashtray with cigarette lighter, continue with
step 4, if not go to step 5.
•
Refer to the Owner’s Manual for the explanation of
each mode.
Horn/Siren Switch:
4. Remove the ashtray with cigarette lighter, (two
self-tapping screws, one connector, and four
retaining clips).
•
Set the switch to “HORN” in normal use. If an optional
siren is installed, set the switch to “SIREN.”
Glass Breakage Sensor:
ASHTRAYWITH
CIGARETTE LIGHTER
•
Do not attach anything like scotch tape over the
holes; this is the microphone pickup.
Sensitivity Adjustment Knob:
•
Adjust the sensitivity only if the customer requests
it; the sensitivity adjustment of the glass breakage
sensor is factory set.
CONNECTOR
•
Be careful when you adjust the sensitivity; if you
raise the sensitivity too much, the security system
can give a false alarm, and if the sensitivity is too
low, the security system may not work even if
glass is broken.
SELF-TAPPING
SCREWS
CLIP
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
All 21624 (0008)
3 of 12
5. Remove the left fuse box cover (three retaining
clips and two tabs).
7. Remove the driver’s door sill molding (four clips).
CLIP
TAB
CLIP
DRIVER'S DOOR
SILL MOLDING
LEFT FUSE
LEFT FUSE
BOX COVER
BOX
TAB
CLIP
RETAINING
CLIPS
6. Remove the driver's dashboard lower cover (three
screws, and five retaining clips).
8. Remove the kick panel (two clips, and pull).
SCREW
KICK PANEL
SCREW
SCREW
DRIVER'S
DASHBOARD
LOWER COVER
CLIP
CLIP
4 of 12
All 21624 (0008)
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
9. Remove the right fuse box cover (three retaining
clips and two tabs).
11. Open the glove box, and remove the two screw
caps and seven self-tapping screws. Unplug the
connector, and remove the glove box by pulling it
toward you.
GLOVE BOX
TAB
CLIP
CONNECTOR
SELF-TAPPING
SCREW
CAPS
RIGHT FUSE
BOX COVER
RIGHT FUSE
BOX
TAB
12. Lower the steering wheel tilt lever. Remove the
upper and lower steering column covers (three
screws, six tabs, and one harness clip). Gently
push on the six retaining tabs, and separate the
two steering column covers.
10. Remove the passenger’s dashboard lower cover
(three screws and seven retaining clips).
GLOVE BOX
UPPER
STEERING
COLUMN COVER
TABS
(Push.)
TABS
(Push.)
STEERINGWHEEL
TILT LEVER
SCREW
SCREW
LOWER
STEERING
COLUMN
SCREW
PASSENGER'S
DASHBOARD
LOWER COVER
COVER
Push
CLIP
TAB
SCREWS
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
All 21624 (0008)
5 of 12
13. Measure and mark the upper steering column
cover.
16. Locate the 2-pin connector included in the kit, and
lower the lock. Firmly push the LED terminals into
the 2-pin connector.
Insert.
Lock.
5.5 mm
DRILL
UPPER STEERING
COLUMN COVER
WHITEWIRE
20 mm
REDWIRE
17. Measure and mark the driver's dashboard lower
cover. (If necessary, remove the insulation.)
MARK
14. While wearing eye protection, lightly center-punch
the mark; then drill a 5.5 mm hole through the
upper steering column cover. Remove all burrs.
First drill with a
10 mm bit, then with
a 12 mm drill bit.
15. Route the terminal ends of the LED through the
hole you just drilled, and secure the LED with the
push nut. Install the push nut securely.
MARK
LED
BACK OF
DRIVER'S
25 mm
DASHBOARD
LOWER COVER
UPPER STEERING
COLUMN COVER
15 mm
18. While wearing eye protection, lightly center-punch
the mark; then drill a 12 mm hole through the
center-punched mark.
•
•
First drill a pilot hole with a 10 mm bit, then
finish with a 12 mm bit.
PUSH NUT
Remove all burrs.
PUSH NUT
6 of 12
All 21624 (0008)
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
19. Route the terminal ends of the disarm switch
through the hole you just drilled, and secure it with
the washer and 12 mm nut from the kit.
21. Push the wire tie with clip into the hole in the back
of the control unit bracket. Position the control unit
bracket on the driver's dashboard lower cover, and
install the three self-tapping screws from the
attachment kit.
NUT
SELF-TAPPING
SCREW
WASHER
WIRE TIE
WITH CLIP
DRIVER'S
DASHBOARD LOWER
COVER
CONTROL
UNIT
BRACKET
DISARM SWITCH
BACK OF DRIVER'S
DASHBOARD
LOWER COVER
20. Locate the 3-pin connector included in the kit.
Firmly push the disarm switch terminals into the
3-pin connector until they click into position, and
lower the lock. Slide the white connector clip onto
the underside of the 3-pin connector.
22. Position the control unit on the control unit bracket,
and install the two 4 x 30 mm washer-screws.
Secure the antenna to the control unit bracket with
the wire tie with clip you just installed, as shown.
Secure the antenna parallel with the control unit.
3-PIN
CONNECTOR
Lock.
4 x 30 mm
WASHER-SCREW
Insert.
WHITE
CONNECTOR
CLIP
CONTROL
UNIT
ANTENNA
BLUEWIRE
CONTROL UNIT
BRACKET
BLACKWIRE
WIRE TIE WITH CLIP
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
All 21624 (0008)
7 of 12
23. Secure the disarm switch wire harness to the
disarm switch with one short wire tie, then attach
the harness to the driver's dashboard lower cover
with two halves of a cushion tape in the areas
shown. (Cut a cushion tape in half with scissors,
and use the two halves to secure the harness.)
26. Attach the 14-pin connector of the security system
wire harness to the side of the vehicle connector.
LEFT FUSE BOX
SECURITY SYSTEM
WIRE HARNESS
14-PIN CONNECTOR
CONNECTOR
CLIP
DISARM SWITCH
SHORT
WIRE TIE
CONTROL
UNIT
BRACKET
VEHICLE
CONNECTOR
CUSHIONTAPE
(Cut in half.)
27. Locate the two 2-pin connectors blue-taped to the
vehicle harness, and remove the blue tapes to free
the connectors. Plug the 2-pin connectors you just
freed into the 2-pin connectors of the security
system wire harness. Connect the blue 2-pin
connector of the vehicle harness to the blue 2-pin
connector of the security system wire harness.
24. Push the clip on the 3-pin connector of the disarm
switch into the hole in the control unit bracket.
25. From the driver's side, route the 14-pin connectors
of the security system wire harness to the left fuse
box. Unplug the 14-pin connector from the fuse
box, and plug the 14-pin connectors of the security
system wire harness in between.
LEFT FUSE BOX
LEFT FUSE
BOX
2-PIN
CONNECTORS
(GRAY)
SECURITY SYSTEM
WIRE HARNESS
SECURITY
SYSTEM
WIRE
HARNESS
2-PIN
CONNECTORS
(BLUE)
14-PIN CONNECTOR
(VEHICLE HARNESS)
14-PIN CONNECTORS
(SECURITY SYSTEM
WIRE HARNESS)
8 of 12
All 21624 (0008)
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
28. Remove the upper bolt that fastens the engine
hood opener, and attach the ground terminal of the
security system wire harness with the ground bolt
from the kit.
31. Unplug the 20-pin connector from the left fuse box,
and plug the two 20-pin connectors (white) of the
security system wire harness in between.
VEHICLE
20-PIN
CONNECTOR
1-PIN CONNECTOR OF
SECURITY SYSTEMWIRE
LEFT
FUSE
BOX
No. 5
CONNE
OF FUS
ENGIN
OPENE
20-PIN CONNECTORS
SECURITY SYSTEM
BOLT
OF SECURITY SYSTEM
WIRE HARNESS
WIRE HARNESS
ENGINE HOOD
GROUNDTERMINAL OF
OPENER MOUNT BOLT
SECURITY SYSTEM
(Discard.)
WIRE HARNESS
32. Locate the 2-pin connector blue-taped to the
vehicle harness 18-pin connector, and remove the
blue tape to free the connector. Connect the 2-pin
connector you just freed to the 2-pin connector of
the security system wire harness.
29. Plug the 1-pin connector (white) of the security
system wire harness into the No. 5 connector of
the fuse box.
30. Under the dashboard at the fuse box, locate the
4-pin connector blue-taped to the vehicle harness
(22-pin connector), and remove the blue tape to
free the connector. Connect the 4-pin connector
you just freed to the 4-pin connector (C) of the
security system harness.
BLUETAPE
(Remove.)
VEHICLE
18-PIN CONNECTOR
VEHICLE
2-PIN CONNECTOR
VEHICLE
22-PIN CONNECTOR
LEFT
FUSE
BOX
BLUETAPE
(Remove.)
LEFT
FUSE
BOX
4-PIN
CONNECTOR OF
2-PIN CONNECTOR OF
SECURITY SYSTEM
WIRE HARNESS
SECURITY
SYSTEM WIRE
HARNESS
(WHITE)
SECURITY SYSTEM
WIRE HARNESS
SECURITY SYSTEM
WIRE HARNESS
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
All 21624 (0008)
9 of 12
33. Remove the clip from the hole in the left knee
bolster, use a utility knife to cut the clip off of the
vehicle harness. Take care not to damage the
vehicle harness.
37. Position the 5-pin and 4-pin relays onto the other
relay bracket, and install one 6 x 12 mm
washer-bolt and 6 mm nut.
RELAY BRACKET
LEFT KNEE
BOLSTER
6 mm
FLANGE
NUT
6 x 12 mm
WASHER-BOLT
4-PIN RELAY
About 45°
VEHICLE
HARNESS
5-PIN RELAY
HARNESS CLIP
(Cut and discard.)
34. Assemble three fuse cases as shown. Attach the
appropriate fuse label to each fuse case of the
security system wire harness, then attach the red
connector clip as shown.
5-PIN RELAY
38. Plug the 6-pin and 4-pin connectors of the security
system wire harness into the 5-pin and 4-pin
RED
relays; then attach the relay bracket to the steering
hanger beam with one 6 x 12 mm washer-bolt and
6 mm flange nut. (The 5-pin relay has a 6-pin
CONNECTOR
CLIP
FUSE SEAL
(15 A)
FUSE SEAL
(3 A)
connector.)
5-PIN RELAY
4-PIN
RELAY
LEFT
KNEE
BOLSTER
6 x 12 mm
WASHER-BOLT
RELAY
BRACKET
FUSE
CASE OF
SECURITY
SYSTEM
WIRE
HARNESS
4-PIN
CONNECTOR
6-PIN CONNECTOR
5-PIN
RELAY
6 mm
FLANGE NUT
LONG
WIRE TIE
6 mm
FLANGE
NUT
VEHICLE HARNESS
35. Position one of the relay brackets on the left knee
bolster, and install one 6 x 12 mm washer-bolt and
6 mm flange nut. Push the red connector clip on
the fuse case of the security system wire harness
into the hole in the relay bracket.
4-PIN
RELAY
6 x 12 mm
WASHER-
BOLT
36. Secure the security system wire harness to the
vehicle harness with one long wire tie in the area
shown.
STEERING HANGER BEAM
10 of 12
All 21624 (0008)
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
39. Route the 2-pin connector of the LED through the
lower steering column cover, and connect it to the
2-pin connector of the security system wire
harness. Reinstall the lower and upper steering
column covers.
41. On the left of the steering wheel, secure the
security system wire harness to the vehicle
harness with three long wire ties in the areas
shown.
LONGWIRE
TIES
UPPER
STEERING
COLUMN
COVER
LED
LED HARNESS
LEFT FUSE
BOX
LOWER
STEERING
COLUMN
COVER
VEHICLE
HARNESS
SECURITY SYSTEM
2-PIN
CONNECTORS
WIRE HARNESS
SECURITY SYSTEM
WIRE HARNESS
42. On the left of the fuse box, secure the security
system wire harness to the vehicle harness with
two long wire ties.
40. Secure the security system wire harness and the
LED 2-pin connector to the vehicle harness with
three long wire ties and one short wire tie. Secure
the wire ties only in the areas shown and not to the
yellow SRS harness.
LEFT FUSE
BOX
LED 2-PIN
CONNECTOR
SHORT
WIRE TIE
LONGWIRE
TIES
LONG
WIRE
TIES
SECURITY SYSTEM
WIRE HARNESS
VEHICLE HARNESS
VEHICLE
HARNESS
SECURITY SYSTEM
WIRE HARNESS
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
All 21624 (0008)
11 of 12
43. Plug the 3-pin connector of the security system
wire harness into the 3-pin connector of the disarm
switch harness. Plug the 22-pin connector of the
security system wire harness into the control unit;
then reinstall the driver's dashboard lower cover.
46. Route the sub-harness along the vehicle harness.
Inside the glove box, locate the 2-pin connector
blue-taped to the vehicle harness, and remove the
blue tape to free the connector. Plug the 2-pin
connector of the sub-harness into the 2-pin
connector you just freed.
SECURITY SYSTEMWIRE HARNESS
22-PIN CONNECTOR
BLUETAPE
2-PIN
(Remove.)
CONNECTOR
H
OR
VEHICLE
HARNESS
SUB-
HARNESS
CONTROL UNIT
DRIVER'S
SHORT
WIRE TIES
DASHBOARD
SECURITY SYSTEMWIRE
LOWER COVER
HARNESS 3-PIN
CONNECTOR
47. Secure the sub-harness to the vehicle with three
short wire ties.
48. Open the hood, and attach the cover on the
bulkhead center stay.
44. Unplug the 4-pin connector from the right fuse box
and plug the 4-pin connector of the sub-harness
there.
VEHICLE
4-PIN CONNECTOR
HOLE IN
INNER
LOWER
PILLAR
BULKHEAD
CENTER STAY
COVER
49. Check that all wire harnesses are routed properly
and all connectors are plugged in.
50. Reinstall all removed parts.
SUB-HARNESS
4-PIN CONNECTOR
SUB-HARNESS
51. Reconnect the negative cable to the battery.
45. Push the clip of the sub-harness 4-pin connector
into the hole in the right front inner lower pillar.
52. Enter the customer’s radio anti-theft code, if
applicable, and reset the radio station presets.
53. Reset the clock.
54. Check operation of the security system according
to the Owner’s Manual supplied.
12 of 12
All 21624 (0008)
© 2000 American Honda Motor Co., Inc - All Rights Reserved.
|