Accessory
Application
Publications No.
AII 37561-38377
2008 ACCORD
2-DOOR
INSTALLATION
INSTRUCTIONS
BACK-UP SENSOR
Issue Date
NOV 2007
PARTS LIST
Control unit bracket (L4)
Back-up Sensor Attachment Kit
P/N 08V67-TE0-100A
Control unit
Control unit bracket (V6)
Beeper
13 Wire ties
4
Sensor clips
Wire tie with clip
Back-up sensor harness
2
Wire ties with holder
Back-up sensor subharness
2
Urethane tapes
Fuse label
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
AII 37561-38377 (0711)
1 of 15
08V67-TE0-1000-91
2. Disconnect the negative cable from the battery.
5. Remove the rear trim panel (five clips and three
hooks).
3. Remove the two covers from the rear bumper and
remove the rear bumper (two bolts, six self-tapping
screws, two clips, and unplug one connector).
REAR TRIM PANEL
4 CLIPS
NOTE: Have an assistant help you remove the rear
bumper.
CONNECTOR
2 BOLTS
3 HOOKS
CLIP
6. Fold down the rear seat back by pulling the lever
under the rear shelf inside the trunk.
6 SELF-TAPPING
REAR SHELF
REAR SEAT BACK
2 COVERS
2 CLIPS
SCREWS
REAR
BUMPER
4. Remove the trunk floor mat (one clips).
TRUNK
FLOOR MAT
CLIP
LEVER (Pull.)
7. Remove the left trunk side lining (five clips).
LEFT TRUNK
SIDE LINING
2 CLIPS
3 CLIPS
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
AII 37561-38377 (0711)
3 of 15
8. Using the trim tool, remove the rear shelf access
10. Remove the left rear speaker (one bolt and
disconnect the vehicle connector).
panel, then release the front rear speaker retaining
tab.
BOLT
LEFT REAR
SPEAKER
REAR SHELF
ACCESS PANEL
LEFT REAR
SPEAKER COVER
VEHICLE
CONNECTOR
TRIM TOOL
(TN SILRIMTL10)
11. Wrap urethane tape around the control unit at the
area shown. Then, attach the control unit bracket
into the control unit.
L4 MODEL
9. Remove the left rear speaker cover (nine retaining
tabs).
URETHANE
TAPE
9 RETAINING
TABS
CONTROL UNIT
BRACKET
LEFT REAR
SPEAKER
COVER
CONTROL
UNIT
V6 MODEL
CONTROL UNIT
BRACKET
URETHANE
TAPE
CONTROL
UNIT
4 of 15
AII 37561-38377 (0711)
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
L4 Model
V6 MODEL
• Loosen the upper bolt from the relay support.
Remove the relay support (one bolt and
disconnect the vehicle connectors).
12. Install the control unit to the vehicle panel:
•
Partially thread the 6 mm flange nut onto the
control unit bracket stud. Insert the control unit
bracket stud into the hole in the vehicle panel.
Tighten the 6 mm flange nut to secure the
bracket to the vehicle panel.
BOLT
(Loosen.)
VEHICLE PANEL
6 mm
FLANGE NUT
HOLE
VEHICLE
PANEL
BOLT
(Remove.)
RELAY
SUPPORT
VEHICLE CONNECTORS
CONTROL UNIT
BRACKETSTUD
BOLT
• Install the control unit bracket to the relay support
using the 6 x 12 mm flange bolt and the 6 mm
flange nut.
CONTROL
UNIT
HOOK
STOPPER
CONTROL
UNIT
BRACKET
CONTROL UNIT
BRACKET
CONTROL
UNIT
STUD BOLT
CONTROL
UNIT
RELAY
SUPPORT
6 mm
6 x 12 mm
FLANGE NUT
FLANGE BOLT
RELAY
SUPPORT
•
Reinstall the relay support.
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
AII 37561-38377 (0711)
5 of 15
13. Attach the 2A fuse label to the fuse case on the
14. Disconnect the back-up light 2-pin connector from
the left taillight, and plug it into the back-up sensor
harness 2-pin connector. Plug the remaining
back-up sensor harness 2-pin connector into the left
taillight.
back-up sensor harness.
FUSE
CASE
BACK-UP LIGHT
2-PIN CONNECTOR
LEFT TAILLIGHT
BACK-UP
HARNESS
2-PIN
CONNECTOR
BACK-UP
SENSOR
HARNESS
2A FUSE LABEL
BACK-UP
HARNESS
CONNECTOR
BACK-UP SENSOR
HARNESS
TRUNK ROOM
6 of 15
AII 37561-38377 (0711)
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
15. At the left taillight, secure the back-up sensor
harness to the vehicle harness with one wire tie.
V6 MODEL
VEHICLE
HARNESS
BACK-UP
SENSOR
HARNESS
WIRE TIE
VEHICLE
HARNESS
VEHICLE
HARNESS
BACK-UP
SENSOR
HARNESS
GREEN TAPE
16. Plug the back-up sensor harness 14-pin connector
into the control unit, and route the harness forward
along the vehicle harness. Secure the back-up
sensor harness to the vehicle harness at the green
tape.
WIRE
TIE
CONTROL
UNIT
CONTROL
UNIT
BACK-UP SENSOR
HARNESS 14-PIN
CONNECTOR
L4 MODEL
BACK-UP SENSOR
HARNESS
VEHICLE
HARNESS
CONTROL
UNIT
CONTROL
UNIT
GREEN
TAPE
BACK-UP SENSOR
HARNESS 14-PIN
CONNECTOR
WIRE
TIE
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
AII 37561-38377 (0711)
7 of 15
17. Secure the back-up sensor harness to the vehicle
V6 MODEL
harness with two additional wire ties at the locations
shown.
2 WIRE TIES
VEHICLE
HARNESS
L4 Model
2 WIRE TIES
VEHICLE
HARNESS
WIRE TIE
WIRE TIE
BACK-UP SENSOR
HARNESS
VEHICLE
HARNESS
BACK-UP SENSOR
HARNESS
VEHICLE
BACK-UP
HARNESS
SENSOR
HARNESS
18. Secure the back-up sensor harness clip to the hole
in the vehicle panel.
BACK-UP SENSOR
HARNESS
VEHICLE
PANEL
BACK-UP SENSOR
HARNESS
BACK-UP SENSOR
HARNESS CLIP
8 of 15
AII 37561-38377 (0711)
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
19. Using scissors cut one urethane tape in half, and
23. Secure the beeper harness to the vehicle harness
with one wire tie.
then cut one of the halves again. Wrap the cut pieces
around the beeper harness shown.
20. Install the connector clip to the beeper 2-pin
connector.
WIRE TIE
VEHICLE
HARNESS
URETHANE
TAPE
BEEPER 2-PIN
CONNECTOR
BEEPER 2-PIN
CONNECTOR
CONNECTOR
CLIP
2-PIN CONNECTOR
(Wrap from the end of
the 2-pin connector.)
BEEPER
HARNESS
BEEPER
Wrap the urethane tapes
24. Plug the beeper 2-pin connector into the back-up
sensor harness 2-pin connector.
around the harness.
URETHANE
TAPE
(Cut in half.)
URETHANE TAPE
TRUNK LID HINGE
WIRE TIE
21. Using an isopropyl alcohol on a shop towel, clean
the vehicle panel where the beeper will attach.
VEHICLE
HARNESS
BUZZER
ADHESIVE
BACKING
VEHICLE
PANEL HOLE
BUZZER 2-PIN
CONNECTOR
BACK-UP SENSOR
HARNESS 2-PIN
CONNECTOR
URETHANE TAPE
Cut in quarter
Attachment
position.
BUZZER
HARNESS
2-PIN CONNECTOR
22. Remove the adhesive backing from the beeper, and
attach it to the opening in the left rear speaker at the
location shown. Route the beeper harness through
the hole in the rear shelf.
25. Wrap the remaining piece of a urethane tape around
the connector.
26. Secure the 2-pin connection to the vehicle harness
with one wire tie.
27. Route the back-up sensor harness as shown and
secure it to the vehicle harness with three wire ties.
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
AII 37561-38377 (0711)
9 of 15
28. Install one wire tie with clip to the holder with the fuse
case, and attach the wire tie to the vehicle harness.
VEHICLE
HARNESS
WIRE TIES
WIRE TIE
VEHICLE
HARNESS
WITH CLIP
FUSE
CASE
WIRE
TIE
BACK-UP SENSOR
HARNESS
VEHICLE
GROMMET
29. Remove the vehicle grommet from the rear panel.
30. Route the back-up sensor 6-pin connector through
the hole in the rear panel, and seat the harness
grommet in the rear panel hole.
BACK-UP
SENSOR
HARNESS
VEHICLE
HARNESS
TRUNK ROOM
BACK-UP
SENSOR
HARNESS
6-PIN
CONNECTOR
WIRE TIE
GROMMET
GROMMET
Outside
Inside
Hole from which
the grommet has
been removed.
BACK-UP SENSOR
HARNESS
31. Secure the back-up sensor harness to the vehicle
harness with one wire tie.
10 of 15
AII 37561-38377 (0711)
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
32. Install one wire tie with holder to the back-up sensor
NOTE: There are several markings on the inside of the
rear bumper. Before piercing the rear bumper, verify you
have the correct locations.
harness 16-pin connector, and attach the wire tie to
the vehicle harness.
BACK-UP SENSOR
3 MARKS
3 MARKS
HARNESS
WIRE TIE WITH
HOLDER
6-PIN CONNECTOR
REAR BUMPER
PUSHPIN
REAR BUMPER
VEHICLE
HARNESS
MARK
REAR BUMPER
MARK
PUSHPIN
33. Mark the inside of the rear bumper:
•
•
•
•
Locate the three marks on the inside of the
bumper at the center and left side.
Using a pushpin, pierce the rear bumper at the
top and center of the three marks.
Locate the three marks on the inside rear
bumper on the right side.
Using a pushpin, pierce the rear bumper at the
bottom and the center of the right mark.
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
AII 37561-38377 (0711)
11 of 15
34. While wearing eye protection drill the rear bumper:
•
Using 26 mm holes saw, enlarge both lower in
board bumper holes at the center of the bumper.
Remove all burrs.
NOTE: Center sensors are 26 mm holes, side sensors are
24 mm holes.
•
From the outside of the bumper, drill all eight
pierced marks using a 3 mm drill bit.
LOWER
HOLE
HOLE
•
Using a 24 mm hole saw, enlarge the lower
outboard hole on the left side of the bumper.
Remove all burrs.
DRILL
(3 mm
HOLE
DRILL
DRILL BIT)
DRILL
LOWER
HOLE
(3 mm
(26 mm
DRILL BIT)
HOLE SAW)
24 mm
HOLE SAW
REAR BUMPER
BURRS
(Remove.)
REAR BUMPER
35. Install the two corner sensors into the 24 mm holes
in the rear bumper using the sensor clips. Not the
direction and the pin location for each sensor.
BURRS
(Remove.)
CORNER
SENSOR
•
Using a 24 mm hole saw, enlarge the upper
outboard hole on the left side of the bumper.
Remove all burrs.
24 mm HOLE
(White)
Outside
Inside
REAR
BUMPER
CORNER
SENSOR
(White)
DRILL
24 mm
UPPER HOLE
HOLE SAW
SENSOR
CLIP
DRILL
3 mm
DRILL BIT
HOLE
Outside
Inside
REAR
BUMPER
CORNER
SENSOR
(White)
SENSOR
CLIP
24 mm
HOLE
REAR BUMPER
CORNER
SENSOR
(White)
REAR
BUMPER
BURRS
(Remove.)
12 of 15
AII 37561-38377 (0711)
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
36. Install two center sensors into the 26 mm holes in the
2 BACK-UP SENSOR
SUBHARNESS CLIPS
rear bumper using the sensor clips. Note the
direction and location for each sensor.
SENSOR
CLIP
REAR
BUMPER
BACK-UP SENSOR
SUBHARNESS
SENSOR
CLIP
REAR
BUMPER
Outside
Inside
2 CENTER
SENSORS
(Blue)
HOLDER
CLIP
WIRE TIE
WITH CLIP
2 HOLES,
26 mm
SENSOR CLIP
2 CENTER SENSORS
(Blue)
37. Plug the four back-up sensor subharness 2-pin
connectors into each back-up sensor connector.
BACK-UP SENSOR
SUBHARNESS
BACK-UP
SENSOR
JUNCTION CONNECTOR
HARNESS
NOTE: The back-up sensor harness 6-pin connector
and the junction connector must be positioned on the
left side of bumper.
39. Secure the subharness to the bumper using four
harness tapes in the locations shown.
40. Attach one wire tie with holder clip to the back-up
sensor subharness junction connector and secure
the wire tie to the vehicle harness.
RIGHT CENTER
SENSOR
CORNER
LEFT CENTER
SENSOR
SENSOR
CORNER
SENSOR
4 BACK-UP SENSOR
SUBHARNESS 2-PIN
CONNECTORS
BACK-UP SENSOR
SUBHARNESS
JUNCTION
CONNECTOR
BACK-UP SENSOR
HARNESS 6-PIN
CONNECTOR
38. Attach the two center backup sensor subharness
clips to the holes in each center sensor clip.
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
AII 37561-38377 (0711)
13 of 15
41. Using isopropyl alcohol on a shop towel, clean the
area where the harness tapes will attach.
BACK-UP SENSOR
HARNESS
6-PIN CONNECTOR
BACK-UP SENSOR
SUBHARNESS
6-PIN CONNECTOR
4 GREEN
TAPES
BACK-UP SENSOR
SUBHARNESS
CORNER
SENSOR
4 HARNESS
TAPES
REAR
BUMPER
LEFT
CENTER
SENSOR
RIGHT
CENTER
SENSOR
CORNER
SENSOR
42. At each green tape location, attach the back-up
sensor subharness to the rear bumper with four
harness tapes.
43. Plug the back-up sensor harness 6-pin connector
into the back-up sensor subharness 6-pin connector,
then reinstall the rear bumper.
.
NOTE: Have an assistant help you install the rear
bumper
14 of 15
AII 37561-38377 (0711)
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
44. Check that all wire harnesses are routed properly
and that all connectors are plugged in.
45. Reinstall all removed parts.
46. Reconnect the negative cable to the battery.
47. Enter the anti-theft codes for the radio and
navigation systems (if equipped), then enter the
customer’s radio presets.
48. Reset the clock.
49. Check that the back-up sensors work properly as
described in the Accessory User’s Information
Manual supplied.
Beeper Volume Control
Factory setting of the volume control knob on the control
unit is turned to maximum volume. After confirming the
operation check, turn the volume control knob to the
appropriate volume.
CONTROL
UNIT
Volume
down.
VOLUME
CONTROL
KNOB
Volume
up.
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.
AII 37561-38377 (0711)
15 of 15
|