INSTALL INSTRUCTIONS P-MID-1 w/P-MFK-5
MIDDLE PARTITION w/MOUNTING FILLER PANEL KIT
1997-2008 CHEVROLET/GMC FULL SIZE PASSENGER VANS
TOOLS REQUIRED:
Power drill
Drill bit set
Ratcheting wrench
Standard & Metric socket set
HARDWARE:
QTY DESCRIPTION
PART #
5
6
20
12
8
1
1
2
8
¼” x 1 ½” Hex head Lag Bolt
GSM33062
GSM33060
GSM32000
GSM30023
GSM30016
GSM30017
GSM33015
GSM31006
GSM31014
¼” x 1” Hex head Lag Bolt
¼-20 x ¾” Carriage Bolt
¼-20 Serrated Nut
¼-20 Nylock Nut
5/16-18 Nylock Nut
5/16-18 x 2” Hex Head Bolt
5/16 Flat Washer
¼” x 1” Fender Washer
Upper Center Steel
Filler Panel
Passenger Side
Mounting Bracket
Driver Side Upper
Lexan Filler Panel
Passenger Side Steel
Door Filler Panel
(2-Piece) Driver Side
“B” Pillar Mounting
Bracket
Main Partition
Frame
Driver Side Lower
Steel Filler Panel
serrated nuts.
• Press partition as far forward and mark mounting holes where driver side mounting
bracket and “C-pillar” come in contact.
• Pre-drill 3/16” holes into “C-pillar”.
• Attach bracket to C-pillar using (3) ¼” x 1” Hex head lag bolts.
• Plastic trim panel must be notched around bracket to mount.
3. ATTACH PASSENGER SIDE MOUNTING BRACEKT:
• Press partition as far forward as
possible and holding bracket to
partition (square tubing section)
determine where to slot headliner to
accept mounting bracket.
• Slot headliner and position mounting
bracket to be flush with vehicle inner
roof support.
• Mark (3) mounting holes and pre-
drill using 3/16” drill bit.
5/16-18 x 2”
Hex head bolt
• Attach bracket to vehicle using (3)
¼” x 1” Hex head lag bolts.
• Press partition up to bracket and
mark holes where bracket and
partition come together.
Passenger side upper
mounting bracket
• Drill 5/16” holes on these marks and
bolt partition to bracket using 5/16-
18 x 2” Hex head bolt, washer, and
nylock nut.
4. ATTACH UPPER STEEL CENTER FILLER PANEL:
• Attach upper center filler to partition through the holes pre-drilled at subassembly
using ¼-20 x ¾” Carriage bolts and serrated nuts.
• Tighten all hardware.
P-MID-1^MFK-5_INST_9-07
5. ATTACH DRIVER SIDE UPPER LEXAN FILLER PANEL:
• Position driver side ¼” lexan filler panel to partition so that minimal space is between
the vehicles window, (or window guard) and the lexan filler.
NOTE: It is necessary to keep a 1/8” gap between the window or guard and the filler to allow for
expansion and contraction of the lexan during temperature fluctuations.
• Drill (6) 5/16” holes evenly spaced through both the ¼” lexan filler panel and the
partition frame. Attaching to the frame directly will help to avoid filler rattling.
• Bolt lexan filler to partition using ¼-20 x ¾” carriage bolts and nylock nuts.
6. ATTACH DRIVER SIDE LOWER STEEL FILLER PANEL:
• Position driver side lower aluminum filler panel tight to vehicles interior trim and
floor.
• Using slots in filler panel as a drill guide mark and drill partition using 5/16” drill bit.
• Attach filler panel to partition using ¼-20 x ¾” carriage bolts and serrated nuts.
7. ATTACH PASSENGER SIDE DOOR STEEL FILLER PANEL:
• Position on front row bench in van close side doors.
• Hold filler panel to partition so that it does not interfere door mechanisms.
• Mark and drill 3/16” holes through partition tubing.
• Attach filler to partition using ¼-20 x ¾” Hex head thread cutting bolts.
• Vacuum out all metal shaving and double check door operation.
Lexan
Notched
¼-20 x ¾”
P-MID-1^MFK-5_INST_9-07
|