Havis Shields KK K9 C14 K 32 User Manual

INSTALLATION INSTRUCTIONS KK-K9-C14-K-32  
32” K9 TRANSPORTATION SYSTEM  
2000-2006 CHEVROLET TAHOE / GMC YUKON (4 Door)  
TOOLS REQUIRED:  
Power drill  
Drill bit set  
Standard & metric socket sets  
Phillips screwdriver  
Open-end wrench set  
Wire cutters / Crimping tool  
Ratcheting wrench  
HARDWARE:  
QTY DESCRIPTION  
PART #  
20  
30  
50  
6
¼-20 x ½” Stainless Carriage Bolts  
GSM32022  
GSM32024  
GSM30023  
GSM33060  
¼-20 x ¾” Stainless Carriage Bolts  
¼-20 Hex Flange Serrated Nuts Zinc  
¼” x 1” Hex Head Lag Bolt  
22  
24  
12  
10  
6
#12 x ¾” Stainless Sheet Metal Screws  
#10 x ¾” Sheet Metal Screws Stainless  
#10 x ½” Sheet Metal Screws Stainless  
10-32 x ¾” Machine Screw Screws Stainless  
#10 x ¾” Sheet Metal Screws Zinc  
Tube Silver Caulk  
GSM34177  
GSM34170  
GSM34169  
GSM34098  
GSM33195  
PRM97343  
KNM01029  
1
1
32” x 45” x ½” Rubber Mat  
Always!  
¾ Read all instructions before installing any Havis-Shields Equipment Corp products.  
¾ Disconnect the vehicle battery. Removing seat bolts on some vehicles may give the vehicles  
computer a false reading, causing a warning light on the instrument cluster. This requires the  
vehicles’ computer to be reset with a vehicle diagnostics tool.  
¾ Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!  
¾ Use only hardware provided with install kit.  
¾ For product support, visit the Install Instructions Section of our website at  
524-9900 and ask for technical support.  
SUB ASSEMBLY:  
Mount dome light to ceiling and attach wire  
Remove rear seats and door panels.  
Remove trim panels around the rear door opening to minimize damage while sliding main  
housing assembly into the vehicle.  
Attach rear housing extension plate to K9 floor using ¼” x ¾” Carriage bolts and serrated  
nuts. The carriage bolt will go up from the bottom. It may be necessary to drill holes to  
accommodate the extension plate due to the various models.  
3. INSTALL MOUNTING LEGS:  
Using ¼-20 x ¾” Carriage bolts attach mounting legs to hold down plates.  
Loosely attach hold down plates to floor using existing seat mounting studs and nuts used  
to hold down seats.  
Rear housing extension should  
be attached at this time  
Note: Use one OEM nut as a spacer under the plate.  
4. SLIDE IN K9 MAIN HOUSING:  
Slide in main housing  
Mark & drill 5/16” holes in K9 unit floor where mounting legs and floor come together.  
Mount legs to housing loosely using ¼-20 x ¾” Carriage bolts and serrated nuts.  
5. INSTALL TUNNELS AND FILLERS:  
Loosely attach side tunnels to main housing using ¼-20 x ¾” or ½”Carriage bolts (double  
or triple skin) and ¼-20 serrated nuts.  
Place cover step in tunnels and mount using #12 x ¾” Stainless Sheet Metal screws.  
KK-K9-C14-K-32_INST_12-08  
3
6. HOUSING FINAL STEP  
Center housing so tunnels are even on both sides.  
Mount rear housing adapter plate. This piece is 5” long and the width of the housing.  
Drill and mount plate to housing using ¼ x ¾” Stainless Carriage bolts and serrated nuts.  
Note: Carriage bolt head must be on floor side of housing.  
Note: Be sure to check under vehicle for obstructions.  
***The (1) far passenger side hole is located  
overtop of refrigerant lines. Be sure to not  
attach the extension plate in these locations due  
to these refrigerant lines.***  
Extension plate is already attached at this  
time. Attach rear housing extension plate to  
vehicle using ¼” x 1” hex head lag bolts. Pre-  
drill w/ 3/16” pilot. Do not attach the bolt  
located above the refrigerant line.  
Tighten all loose bolts on tunnels and legs.  
Refrigerant  
Line Location  
7. DOOR PANELS AND WINDOW GUARDS:  
Center door panel’s mark and pre-drill holes to 5/32”.  
Attach to doors using #10 x ¾” Stainless Sheet Metal Screws  
Center hinging window guard on door panel and mount using #10 x ½” Stainless Sheet  
Metal Screws. A 5/32” pilot hole is necessary.  
Remove weather stripping from area where window guard bracket will attach.  
Top Mounting  
Bracket  
With top mounting bracket for hinging window guard attached, hinge window up and  
mark placement for top mounting bracket.  
Note: It may be necessary to contour the window guard to the match the contour of the OEM door.  
Hinge down and remove top mounting bracket from guard.  
Mount to location marked previously using #10 x ½” Stainless sheet metal screws.  
Make sure that holes in window guard align with holes in mounting bracket.  
Re-attach weather stripping to door.  
KK-K9-C14-K-32_INST_12-08  
4
Re-attach window guard to top mounting bracket.  
8. FINAL STEPS:  
Mount dome light switch as desired. A switch box is provided so switch can be mounted  
to K9 housing in various locations. (Side of tunnel housing at top works best). Wire to  
12-volt power source.  
Silicone sheet metal seams and gaps. Proper sealing of compartment will eliminate water  
from getting under the K9 unit. Seal seams with silicone.  
Allow silicone to dry overnight before placing in rubber floor mat.  
KK-K9-C14-K-32_INST_12-08  
5

Blue Sea Systems Battery Charger P12 User Manual
Boston Acoustics SPEAKER SYSTEM PRI85SUB User Manual
BT PaperJet 60E User Manual
Champion Manufacturing Air Conditioner 36 User Manual
Energizer Battery Charger CHFG2 User Manual
Epson Printer WP 4530 User Manual
Epson Stylus SX420W User Manual
GE ASQ10AK User Manual
Heat Controller Inc Air Conditioner BG 123G User Manual
Hudson Sales Engineering DocuCutter DC 545 User Manual