Haier AS182ATNDA User Manual

AS182ATNDA  
AU182AFNBA  
(HSU-18CW03/R1)  
AS162ATNCA  
AU162AFNAA  
(HSU-16CW03/R1)  
AS072AZBDA  
AU072ABBAA  
(HSU-07HW03/R1)  
AS072AZNDA  
AU072ABNAA  
(HSU-07CW03/R1)  
Cautions  
Disposal of the old air conditioner All these valuable materials may be taken  
to a waste collecting center and used  
Before disposing an old air conditioner again after adequate recycling.  
that goes out of use, please make sure  
it's inoperative and safe. Unplug the air Consult your local authorities for the name  
conditioner in order to avoid the risk of and address of the waste materials  
child entrapment.  
collecting centers and waste paper  
disposal services nearest to your house.  
It must be noticed that air conditioner  
system contains refrigerants, which Safety Instructions and Warnings  
require specialized waste disposal. The  
valuable materials contained in a air Before starting the air conditioner, read  
conditioner can be recycled. Contact your the information given in the User's Guide  
local waste disposal center for proper carefully. The User's Guide contains very  
disposal of an old air conditioner and important observations relating to the  
contact your local authority or your dealer assembly, operation and maintenance of  
if you have any question. Please ensure the air conditioner.  
that the pipework of your air conditioner  
does not get damaged prior to being The manufacturer does not accept  
picked up by the relevant waste disposal responsibility for any damages that may  
center, and contribute to environmental arise due to non-observation of the  
awareness by insisting on an appropriate, following instruction.  
antipollution method of disposal.  
Damaged air conditioners are not to be  
Disposal of the packaging of your put into operation. In case of doubt, consult  
new air conditioner  
your supplier.  
All the packaging materials employed in  
Use of the air conditioner is to be carried  
the package of your new air conditioner out in strict compliance with the relative  
may be disposed without any danger to instructions set forth in the User's Guide.  
the environment.  
Installation shall be done by professional  
The cardboard box may be broken or people, don't install unit by yourself.  
cut into smaller pieces and given to a  
waste paper disposal service. The  
For the purpose of safety, the air  
wrapping bag made of polyethylene and conditioner must be properly grounded in  
the polyethylene foam pads contain no accordance with specifications.  
fluorochloric hydrocarbon.  
Cautions  
Always remember to unplug the air  
conditioner before opening inlet grill.  
Never unplug your air conditioner by  
pulling on the power cord. Always grip  
plug firmly and pull straight out from the  
outlet.  
All electrical repairs must be carried  
out by qualified electricians. Inadequate  
repairs may result in a major source of  
Series  
type  
07  
16,18  
3G1.5MM2  
3G2.0MM2  
Series  
type  
07  
danger for the user of the air conditioner.  
3G1.5MM2+2G0.75MM2  
Do not damage any parts of the air  
conditioner that carry refrigerant by  
piercing or perforating the air  
conditioner's tubes with sharp or pointed  
items, crushing or twistings off the  
surfaces. If the refrigerant spurts out and  
gets into eyes, it may result in serious  
eye injuries.  
Do not obstruct or cover the ventilation  
grille of the air conditioner. Do not put  
fingers or any other things into the  
inlet/outlet and swing louver.  
Do not allow children to play with the  
air conditioner. In no case should children  
be allowed to sit on the outdoor unit.  
Specifications  
The refrigerating circuit is leak-proof.  
10. The wiring diagram is attached in-  
side the machine.  
11. The appliance must be installed on  
strong enough supporter.  
Parts and Functions  
Indoor Unit  
Inlet grill  
Air filter  
Vertical flap  
Use remote controller to  
adjust up and down air flow.  
(Don't adjust it manually.)  
Operation mode indicator  
Timer mode indicator  
Lights up when Timer  
operation is selected.  
Power  
Lights up when unit starts.  
Lights up during compressor  
running.  
AS072AZBDA  
AU072ABBAA  
AS072AZNDA  
AU072ABNAA  
(HSU-07HW03/R1)  
(HSU-07CW03/R1)  
Test running  
Used only for test running in cooling  
when room temp. is below 16  
Don't use it in normal operation.  
.
Inlet grill  
Air filter  
Emergency  
Used when remote controller is lost or  
defective. Unit will run temporarily.  
Remote signal  
A beeping sound is generated when  
a signal from remote controller is  
received.  
Vertical flap  
Use remote controller to  
adjust up and down air  
flow.  
Power  
Timer mode indicator  
Lights up when Timer  
operation  
Operation mode  
Lights up when unit starts.  
Lights up during compressor  
running.  
AS182ATNDA  
AS162ATNCA  
AU182AFNBA  
AU162AFNAA  
(HSU-18CW03/R1)  
(HSU-16CW03/R1)  
AU182AFNBA  
AU162AFNAA  
For models:  
For models:  
AU072ABBAA  
AU072ABNAA  
(HSU-18CW03/R1) (HSU-16CW03/R1)  
(HSU-07HW03/R1) (HSU-07CW03/R1)  
Power Failure Resume (to be applied for a necessary situation):  
After the power failure compensation is set, if power failure suddenly occurs while the air  
conditioner is working, it will resume the previous working state when the power is  
again.  
Setting Method: When the remote controller is on (excluding timer mode and fan mode),  
press the " SLEEP " button on the remote controller 10 times within 5  
seconds, and after the buzzer rings 4 times, the air conditioner will enter  
the state of power failure resume.  
Cancel Method: Press the " SLEEP " button on the remote controller 10 times within 5  
seconds, and after the buzzer rings 2 timer, the power failure compensation  
mode will be cancelled.  
Notes: When a power failure suddenly occurs during the air conditioner is working after  
the power failure resume is set, if the air conditioner will not be used for a long time, please  
cut off the power supply to prevent its operation from being resumed after the power is  
supplied again, or press the "  
" button after the power comes again.  
ON/OFF  
Parts and Functions  
Operation  
Buttons and display of the remote  
Power  
TEMP.  
Used for unit start and  
stop.  
Used to select  
your  
AUTO  
FA  
SWING  
Used to select fan  
speed:  
AM  
PM  
Used to set auto  
ON  
OFF  
fan  
AM  
PM  
AM  
PM  
SLEEP  
TEMP  
MODE  
ON  
Used to select sleep  
mode.  
OFF  
SWING  
FAN  
Used to select AUTO run,  
COOL,DRY,HEAT and  
FAN operation.  
MODE  
CLOCK  
SLEEP  
SET  
SET  
Used to confirm Timer  
and Clock settings.  
TIMER  
CLOCK  
RESET  
LOCK  
CODE  
Used to set correct time  
Used to select code A or  
B ,A or B will be displayed  
on LCD. Please select A  
without special explanation.  
TIMER  
Used to select  
TIMER ON, TIMER  
OFF,  
HOUR  
Used to set clock  
and  
LOCK  
RESET  
Used to lock  
buttons  
Used to reset the controller  
back to normal condition.  
Cautions:  
Note:  
On cooling only unit, heating mode is not available.  
After replacing batteries, press ON/OFF, and display  
becomes as follows:  
Operation mode: AUTO, Temp. :No  
Timer mode: No, Fan speed: AUTO  
The above information is the  
explanation of the displayed  
information, therefore varies  
with those displayed in actual  
operation.  
Parts and Functions  
Buttons and display of the remote  
Operation  
HEA  
DR  
AUTO  
FAN  
COOL  
AM  
PM  
ON  
OFF  
AM  
PM  
AM  
PM  
SIGNAL SENDING  
AUT  
TEMP  
ON  
TEMP  
OFF  
SWING  
FAN  
SWING  
FAN  
MODE  
CLOCK  
SLEEP  
SET  
CLOCK  
LOCK  
TIMER  
MED  
LO  
RESET  
LOCK  
AUT  
AUT  
HI  
TIMER OFF  
TIMER ON  
SLEEP  
Clock  
When unit is started for the first time and after replacing batteries in remote controller,  
clock should be adjusted as follows:  
Press CLOCK button, "AM" or "PM" flashes.  
Press  
or  
to set correct time. Each press will increase or decrease 1min. If the  
button is kept depressed, time will change quickly.  
After time setting is confirmed, press SET, "AM " and "PM" stop flashing, while clock  
starts working.  
Hints  
After replacing with new batteries, remote controller will conduct self-check, displaying  
all information on LCD. Then, it will become normal.  
Operation  
Enjoy yourself by just a gentle press.  
Auto run, Fan operation  
(1) Unit start  
Press ON/OFF button, unit starts.  
Previous operation status appears on  
display.  
(Not Timer setting)  
AUTO  
(2) Select operation mode  
Press MODE button. For each press,  
operation  
AM  
TEMP  
ON  
AUT  
COOL  
DR  
HEA  
FA  
OFF  
SWIN
FAN  
1
Unit will run in selected mode.  
3
4
Stop display at "  
" AUTO or "  
" FAN.  
MODE  
SLEEP  
SET  
OCK  
2
(3) FAN  
TIMER  
Press FAN button. For each press, fan speed  
changes  
RESET  
LOCK  
MED  
LO  
AUT  
AUT  
HI  
Unit will run at selected fan speed.  
Note:AUTO is not available in FAN mode.  
Adjust air flow direction if necessary, referring to page10.  
(4) Unit stop  
Press ON/OFF button.  
Only time remains on LCD.  
All indicators on indoor unit go out.  
Vertical flap closed automatically.  
Hints  
Remote controller can memorize settings in each operation mode. To run it  
next  
time just select the operation mode and it will start with the previous setting.  
Operation  
COOL, HEAT and DRY operation  
Recommendations:  
Use COOL in summer.  
Use HEAT in winter.  
Use DRY in spring, autumn and in damp climate.  
(1) Unit start  
Press ON/OFF button, unit starts.  
Previous operation status appears on display. (Not Timer setting)  
Power indicator on indoor unit lights up.  
AUTO  
(2) Select operation mode  
AM  
Press MODE button. For each press,  
operation  
TEMP  
3
4
ON  
AUT  
COOL  
DR  
HEA  
FA  
5
OFF  
SWIN
FAN  
1
6
Unit will run in operation mode displayed on  
LCD.  
MODE  
SLEEP  
SET  
OCK  
2
TIMER  
(3) Select temp.setting  
RESET  
LOCK  
Press TEMP. button  
Every time the button is pressed, temp. setting increases 1oC  
Every time the button is pressed, temp. setting decreases 1oC  
Unit will start running to reach the temp. setting on  
(4) Fan speed selection  
Press FAN button. For each press, fan speed  
changes  
MED  
LO  
AUT  
AUT  
HI  
COOL operation starts when room  
temp. is higher than temp. setting.  
Unit runs at the speed displayed on LCD.  
Ultra-low air flow  
In HEAT mode, warm air will blow out after a short period  
of time due to cold-draft prevention function.  
In DRY mode, when room temp. becomes 2oC higher than  
temp. setting, unit will run intermittently at LO speed  
regardless of FAN setting.  
Temp. setting+2oC  
Temp.  
On reaching temp. setting,unit  
will run in mild DRY mode.  
Hints  
Remote controller can memorize each operation status. When starting it next time,  
just press ON/OFF button and unit will run in previous status.  
On cooling only unit, heating mode is not available.  
Operation  
(5) Air flow direction adjustment  
After operation mode is selected, vertical flap will open automatically according to the mode.  
Referring to the Fig.  
COOL  
HEAT  
About 10o  
About 60o  
Up and down (Use remote controller)  
Left and right air flow adjustment  
(manual)  
Move the horizontal blade by a knob on  
air  
Press SWING button, vertical flap will move within  
the range shown in the Fig. Press SWING button  
stop it at a fixed position.  
conditioner to adjust left and right direction  
About 10o  
COOL About 45o  
HEAT About 60o  
Cautions:  
Cautions:  
When humidity is high, condensate water  
might occur at air outlet if all horizontal  
louvers are adjusted to left or right.  
It is advisable not to keep vertical flap at  
downward position for a long time in COOL  
or DRY mode, otherwise, condensate  
(6) Unit stop  
Cautions:  
Unit won't restart until 3 minutes have  
elapsed, due to system protection.  
HEAT mode is not available on  
cooling only unit.  
Press ON/OFF button.  
Only time remains on LCD.  
All indicators on indoor unit go out.  
Vertical flap closes automatically.  
Hints  
As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more  
helpful for a better air circulation.  
As warm air flows upward in HEAT mode, adjusting air flow downward will be much more  
helpful for a better air circulation.  
Be careful not to catch a cold when cold air blows downward.  
It is harmful to your health in summer to go frequently in and out of places where temp. difference  
is above 7oC. Temp. difference of 3-5oC will remove your fatigue.  
More than this, unit's load can be reduced and power consumption cut down as well. So, you'd  
Operation  
TIMER operation  
Set Clock correctly before starting Timer operation(referring to page 6)  
You can let unit start or stop automatically at following times: Before you wake up in  
the  
TIMER ON/OFF  
(1)After unit start, select your desire operation mode.  
Operation mode will be displayed on LCD.  
Power indicator on indoor unit lights up.  
(2)TIMER mode selection  
Press TIMER button to change TIMER mode.  
AM  
ON  
Every time the button is pressed, display changes as  
AM  
blan  
ON  
ON  
OFF  
OFF  
TIMER ON-OFF  
TIMER OFF  
TIMER ON  
TEMP  
ON  
Select your desired TIMER mode (TIMER ON or TIMER  
OFF) ON or OFF will flash.  
OFF  
SWING  
FAN  
1
MODE  
CLOCK  
SLEEP  
SET  
(3)Timer setting  
Press HOUR  
4
TIMER  
Every time the button is pressed, time increases 10 min.  
If button is kept depressed, time will change quickly.  
Every time the button is pressed, time decreases 10 min.  
If button is kept depressed, time will change quickly. Time  
will be shown on LCD. It can be adjusted within 24 hours.  
3
2
RESET  
LOCK  
(4)Confirming your setting  
After setting correct time, press SET button to confirm, "ON"  
or "OFF" stops flashing.  
Time displayed: Unit starts or stops at x hour x min. (TIMER  
ON or TIMER OFF).  
Timer mode indicator on indoor unit lights up.  
To cancel TIMER mode  
Just press TIMER button several times until TIMER mode  
Hints  
After replacing batteries or a power failure happens, Time setting should be reset.  
Remote controller possesses memory function, when use TIMER mode next time,  
just  
Operation  
TIMER ON-OFF  
(1)After unit start, select your desired operation mode  
Operation mode will be displayed on LCD.  
Power indicator on indoor unit lights up.  
(2) Press TIMER button to change TIMER mode.  
Every time the button is pressed, display changes as follows:  
blan  
ON  
ON  
TIMER ON-OFF  
OFF  
OFF  
TIMER OFF  
TIMER ON  
AM  
AM  
Select TIMER ON-OFF. "ON" will  
ON  
OFF  
AM  
(3)Time setting for TIMER ON  
TEMP  
Press HOUR  
ON  
Every time the button is pressed, time increases 10min.  
If button is kept depressed, time will change quickly.  
Every time the button is pressed, time decreases 10min.  
If button is kept depressed, time will change quickly.  
OFF  
SWING  
FAN  
1
MO
5
SLEEP  
SET  
CLOCK  
Time will be shown on LCD.  
It can be adjusted within 24 hours.  
AM refer's to morning and PM to afternoon.  
6
TIMER  
3
2
4
SET  
LOCK  
(4) Time confirming for TIMER ON  
After time setting, press TIMER button to  
confirm.  
Time displayed: Unit starts at x hour x min.  
(5) Time setting for TIMER OFF  
Follow the same procedures in "Time setting for TIMER  
(6)Time confirming for TIMER  
After time setting, press SET button to confirm, "OFF" stops flashing.  
Time displayed: Unit stops at X hour X  
To cancel TIMER mode  
Just press TIMER button several times until TIMER mode  
According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or  
Stop-Start can be achieved.  
Operation  
Emergency operation and test operation  
Emergency  
Carry out this operation only when the remote controller is defective or lost.  
When the emergency operation switch is pressed, a " Pi " sound starts once,  
which  
means the start of this operation.  
In this operation, it is not possible to change the  
settings of temperature and air flow speed, it is  
also impossible to do an operation by the timer.  
Room  
temperature  
Designated  
temperatur  
Timer  
mode  
Air  
flow  
Operatio  
n mode  
More than 23oC  
Less than 23oC  
26oC  
23oC  
AUT  
AUT  
COOL  
HEA  
If an air conditioner is a model for both cooling and heating.  
Cooling when the room temperature at the start of operation is above 23oC.  
Heating when the room temperature at the start of operation is less 23oC.  
Test operation:  
Use this switch in the test operation when the room  
temperature is less 16oC, do not use it in the normal  
operation.  
Continue to press the test operation switch for more  
than 5 seconds. After you hear the "Pi" sound twice,  
release your finger from the switch, the cooling  
operation starts with the air flow speed setting "Hi".  
Removal of the restriction of emergency or test  
Press once more the emergency operation switch, or manipulate through the remote  
controller, a "Pi" sound causes the restriction of emergency or test operation to be  
removed.  
When the remote controller is manipulated for the removal, then the selected operation  
by the remote controller.  
Operation  
Comfortable SLEEP  
AM  
Before going to bed at night, you can simply press  
the SLEEP button and unit will bring you a sound  
sleep in selected mode.  
TEMP  
ON  
OFF  
SWING  
FAN  
MODE  
CLOCK  
SLEEP  
SE
TIMER  
RESET  
LOCK  
In COOL mode  
One hour after SLEEP mode starts, temp. will  
become 1oC higher than temp. setting. After  
running for another 1 hour, temp. rises by 1oC  
further. Unit will run for 6 hours then stops  
automatically. Temp. is higher than temp.  
setting so that room temp. won't be too low  
for your sleep.(As shown in Fig.1)  
SLEEP operation starts  
SLEEP operation stops  
Approx. 6  
In HEAT mode  
One hour after SLEEP mode starts, temp. will  
become 2oC lower than temp. setting. After  
running for another 1 hour, temp. decreases  
by 2oC further. Unit will run for 3 hours at this  
temp. then increases another 1oC and stops  
automatically 3 hours later. Temp. is lower  
than temp. setting so that room temp. won't  
be too high for your sleep.  
1 hr  
1 hr  
Rises 1  
Temp.  
Unit stop  
Fig.1  
(As shown in Fig .2)  
Temp.  
1 hr  
Unit stop  
Note:  
Decreases 2  
1 hr  
In AUTO mode, unit will run in SLEEP  
function according to operation mode.  
In FAN mode, comfortable sleep is not  
available.  
Decreases 2  
Approx. 3  
Rises 1  
3 hrs  
SLEEP mode starts  
SLEEP mode stops  
Fig.2  
Maintenance  
Cleaning of unit casing  
Cut off power supply  
before cleaning wipe unit casing with soft cloth.  
In case of heavy stain, clean it with neutral detergent.  
squeeze water in the cloth, wipe off the detergent on  
unit  
Cleaning of remote controller  
Don't use water to wash unit casing, please use dry cloth.  
Don't use glass cleanner or cloth soaked with chemicals.  
Cleaning of air filter  
Maintenance  
Maintenance  
Better use of air conditioner  
Proper room  
Cleaning of the air filter.  
Once  
every  
Proper  
temperature  
Effective use of the  
Closing of doors and windows  
during operation.  
Curtains or blinds  
for windows  
Avoid time-  
wasteful  
Never fail to observe the  
Do not sprinkle water over  
the unit.  
Do not block the inlet or  
outlet.  
Do not pull power plug.  
Do not use for other  
Such as food preservation,  
plant cultivation, or animal  
breeding.  
Trouble Shooting  
Before asking for service, check the following first.  
Phenomenon  
Cause or check  
The system does not restart  
immediately.  
When unit is stopped, it won't restart  
immediately until 3 minutes have elapsed  
to protect the system.  
When the electric plug is pulled out and  
reinserted, the protection circuit will work  
for 3 minutes to protect the air conditioner.  
During unit operation or at stop, a swishing  
or gurgling noise may be heard. At first 2-3  
minutes after unit start, this noise is more  
noticeable. (This noise is generated by  
refrigerant flowing in the system.)  
During unit operation, a cracking noise may  
be heard. This noise is generated by the  
casing expanding or shrinking because of  
temperature changes.  
Noise is heard.  
Normal  
Performanc  
e
Should there be a big noise from air flow in  
unit operation, air filter may be too dirty.  
This is because the system circulates smells  
from the interior air such as the smell of  
furniture, cigarettes.  
Smells are  
Mist or steam are blown  
During COOL or DRY operation, indoor unit  
may blow out mist. This is due to the sudden  
cooling of indoor air.  
Does not work at all.  
Is power plug inserted?  
Is there a power failure?  
Is fuse blown out?  
Multiple  
check  
Is the air filter dirty? Normally it should be  
cleaned every 15 days.  
Poor  
Are there any obstacles before inlet and outlet?  
Is temperature set correctly?  
Are there some doors or windows left open?  
Is there any direct sunlight through the  
window during the cooling operation?(Use  
curtain)  
Are there too much heat sources or too many  
people in the room during cooling operation?  

Advantech Barcode Reader RS 485 User Manual
Briggs Stratton 6FB User Manual
Briggs Stratton 326431 User Manual
Cambo Rearview Mirror with 45& quot; Color LCD LCMR5RP User Manual
Carrier 38CQ User Manual
Casio CELVIANO AP 33V User Manual
Cornelius JetSpray JS7 User Manual
GE AZ29E12DAC User Manual
GE Zoneline AZ28E12EAC User Manual
Graco Baby Accessories User Manual