hp LaserJet 9040mfp
hp LaserJet 9050mfp
start
začínáme
alapismeretek
start
hp LaserJet 9040mfp
hp LaserJet 9050mfp
Getting Started Guide
© 2004 Copyright Hewlett-Packard
Development Company, L.P.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be construed
as constituting an additional warranty.
Trademark Credits
Microsoft, Windows, and Windows NT
are U.S. registered trademarks of Microsoft
Corporation.
Reproduction, adaptation, or translation
without prior written permission is prohibited,
except as allowed under the copyright laws.
HP shall not be liable for technical or editorial
errors or omissions contained herein.
UNIX is a registered trademark of
The Open Group.
The information contained herein is subject
to change without notice.
All other products mentioned herein may be
trademarks of their respective companies.
Publication number
Q3726-90904
Edition 1, 11/2004
Product Setup
Contents
Shipping box space requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Product size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remove the product from the shipping box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Remove internal packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Identify product parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Position the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Install output device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connect product cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Configure the control panel display language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Load Trays 1, 2, 3, and 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Configure embedded Send to e-mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installing Windows printing software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Verify product setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
HP software license terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
FCC regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
ENWW
Contents 3
Introduction
Congratulations on your purchase of the HP LaserJet 9040mfp* (product number Q3726A) or
HP LaserJet 9050mfp (product number Q3728A). The product comes standard with the following
items:
●
256 MB random access memory (RAM)
copying, digital sending, and wide-format printing capabilities
two 500-sheet trays (Tray 2 and Tray 3)
a 100-sheet multipurpose tray (Tray 1)
a 2,000-sheet input tray (Tray 4)
●
●
●
●
●
●
●
an embedded HP Jetdirect print server
an internal hard disk
a duplex printing accessory (for printing on both sides of paper)
The product features an interactive touch screen on the control panel graphical display. You must
choose one of the following paper-handling devices: the 3,000-sheet stacker, the 3,000-sheet
stacker/stapler, the multifunction finisher, or the 8-bin mailbox.
*Multifunction Peripheral
4
Product Setup
ENWW
Where to look for information
Start guide
This guide contains information about
unpacking and installing your product.
Use guide
This guide contains detailed information
about using and troubleshooting and is
available on the CD-ROM that came
with the product. If you would like a hard
copy, use your product to print the use
guide.
Installation checklist
This guide will help you set up and install your new product. For correct installation, please
complete each section in order.
●
●
●
●
Unpack the product
Install the product
steps 1 through 5
steps 6 through15
step 16
Install printing software
Verify product setup
step 17
WARNING!
To avoid injury, do not attempt to lift the product. The product has been designed to roll on wheels.
ENWW
Where to look for information 5
Step 1. Prepare product location
Shipping box space requirements
Make sure that your building has a door or receiving area large enough for delivery of the
shipping box. The approximate dimensions of the shipping box are as follows:
1016 mm wide x 914 mm deep x 1148 mm tall (40 inches wide x 36 inches deep x 57 inches
tall).
Unpacking space requirements
Before removing the plastic wrapping from the shipping box, make sure that you have enough
space to remove the contents from the shipping box, and then roll the product down off its
shipping pallet. HP recommends at least 3 meters (10 feet) of space around the shipping box to
remove all of the shipping materials.
6
Product Setup
ENWW
Product size
Prepare a location for the product that allows for these physical and environmental requirements:
1105 mm (44 in)
1201 mm (47 in)
643 mm
(25 in)
457 mm
(18 in)
1
2
533 mm
(22 in)
648 mm
(26 in)
554 mm
(22 in)
643 mm
(25 in)
457 mm
(18 in)
1
1
The smaller measurement is the space that is required to extend the stacker or stacker/stapler with
the attachment bar still attached to the latch under Tray 4. The larger measurement is the space that
is required to remove the stacker or stacker/stapler from the product. The additional space allows
enough clearance to remove the attachment bar from the latch under Tray 4.
2
3
4
This measurement is the space that is required for Tray 1 when it is fully extended for 11 x 17/A3-
size media.
This measurement shows the depth of the product, including the edge of the control panel and the
standoffs from the Tray 4 casters.
This measurement is the space that is required to fully extend Tray 2 or Tray 3.
HP LaserJet 9040mfp and 9050mfp dimensions with the optional 3000-sheet stacker or
the optional 3000-sheet stacker/stapler (top and side views)
ENWW
Installation checklist 7
1105 mm (44 in)
1201 mm (47 in)
643 mm
(25 in)
457 mm
(18 in)
1
2
533 mm
(22 in)
648 mm
(26 in)
554 mm
(22 in)
457 mm
(18 in)
643 mm
(25 in)
1
1
The smaller measurement is the space that is required to extend the stacker or stacker/stapler with
the attachment bar still attached to the latch under Tray 4. The larger measurement is the space that
is required to remove the stacker or stacker/stapler from the product. The additional space allows
enough clearance to remove the attachment bar from the latch under Tray 4.
2
3
4
This measurement is the space that is required for Tray 1 when it is fully extended for 11 x 17/A3-
size media.
This measurement shows the depth of the product, including the edge of the control panel and the
standoffs from the Tray 4 casters.
This measurement is the space that is required to fully extend Tray 2 or Tray 3.
HP LaserJet 9040mfp and 9050mfp dimensions with the optional 3000-sheet stacker or
the optional 3000-sheet stacker/stapler and the ADF lid open (top and side views)
8
Product Setup
ENWW
1194 mm (47 in)
1308 mm (52 in)
643 mm
(25 in)
457 mm
(18 in)
1
2
503 mm
(20 in)
617 mm
(24 in)
691 mm
(27 in)
457 mm
(18 in)
643 mm
(25 in)
3
1
This measurement is the space that is required to extend the multifunction finisher with the
attachment bar still attached to the latch under Tr |