Gamber Johnson Automobile Accessories MCS EPIC17 User Manual

INSTALLATION INSTRUCTIONS  
Product  
Revision  
Form #  
9", 13" & 17" EPIC Console Boxes  
MCS-EPIC9, MCS-EPIC13, MCS-EPIC17  
Rev. D  
INST-104  
.25-20  
BUTTON HEAD  
HARDWARE  
The MCS-EPIC9, MCS-EPIC13 or MCS-EPIC17 can be  
installed on Gamber-Johnson MCS-Top Plates and on  
top plates made by other mount manufacturers, or  
may be bolted directly to the floor or transmission  
hump of your vehicle. When bolting to the floor,  
check under the vehicle to be sure you will not  
damage the transmission housing or other  
CONSOLE  
BOX  
under-floor parts. Bolts for attaching the console to  
the floor are not furnished with the mount.  
CONSOLE BASE  
TOP PLATE  
Installing MCS-EPIC9, MCS-EPIC13 or MCS-EPIC17 on  
Gamber-Johnson MCS-Top Plate:  
1. Place the MCS-Top Plate in the vehicle in the  
approximate position it will occupy when it is installed.  
Set the console on the top plate to determine the  
desired position. Mark that position or make note of  
which slots line up with the mounting holes in the  
console base. Remove the console and top plate from  
vehicle.  
.25-20 CARRIAGE  
BOLT HARDWARE  
2. Insert (4) .25-20 x 1.00 carriage bolts, from the bottom side, through slots in the top plate and mounting  
holes in console base. Add (4) flat washers, (4) lock washers and (4) .25-20 hex nuts from the top side.  
3. Install console base and top plate into vehicle according to the instructions provided with the vehicle base.  
4. Assemble faceplates to control heads as described in instruction sheet INST3.  
Install the control heads, accessories and blank panels into the console box.  
6. Electrically connect the equipment at this time. It is important to allow extra wire length for servicing the  
equipment. Grommets are provided for lining knockout holes.  
7. Slide the console box over the console base. The height and angle can be adjusted if needed by removing  
the (4) .25-20 x .50 Button Head Screws from the sides of the console box, repositioning the slots on the  
console box with the threaded inserts on the console base and reinstall the Button Head Screws.  
Installing MCS-EPIC9, MCS-EPIC13 or MCS-EPIC17 on Top Plates by other manufacturers:  
The slotted hole pattern in the base of the Epic Boxes lines up with the hole pattern in several top plates made  
by other mount manufacturers.  
Installation is similar to that listed above except for item #2.  
Size and quantity hardware depends on top plate being used and must be supplied by customer.  
Product Mounting Disclaimer  
Gamber-Johnson is not liable under any theoryof contract or tort law for any loss, damage, personal injury, special, incidental or consequential damagesfor personal injury orother damage  
of any nature arising directly or indirectly asa result of the improper installation or use of its products in vehicleor any other application. In order to safely install and use Gamber-Johnson  
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is  
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications  
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.  
© copyright2012 Gamber-Johnson, LLC  
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868  
Sheet 1 of 2  
INSTALLATION INSTRUCTIONS  
Product  
Faceplates  
Date  
02/23/01  
Form #  
INST3  
ASSEMBLING MCS FACEPLATES: (Refer to figure 1)  
1. Check that the following pieces are present:  
Dual lock fastener (supplied w/console box)  
(1) faceplate vertical offset  
(1) faceplate top bracket  
(1) flat washer #6  
(1) 6-32 nut  
2. For each faceplate, slide the faceplate vertical offset  
(item 1) on the stud in faceplate top bracket (item 2).  
Add flat washer (item 3) and hex nut (item 4). Remove  
the extra strips of dual lock fastener pressed onto each  
console box under holddown rails, cut to same length as  
each faceplate, remove protective film covering the  
adhesive strip and apply to top bracket as shown.  
3. If the faceplates are being mounted in an older style MCS Console Box (those with threaded inserts on the  
top surface of the side panels/holddown screws passing through slots in existing face plates or blank  
panels), DO NOT attach the strip of dual lock fastener on each faceplate as described above. When  
installing faceplates into these MCS Console Boxes, mark any that cover the threaded inserts and drill a .312  
diameter clearance hole as shown in Figure 1.  
ASSEMBLING MCS FACEPLATES TO CONTROL HEADS AND INSTALLING IN MCS CONSOLE BOXES (Refer to figures  
2 & 3).  
1. Install the faceplates on each control head as shown in figure 2. Adjust the faceplates so the mounting  
holes in the sides of the control head line up in the slots of the faceplate vertical offsets and so the desired  
amount of the control head will extend from the console. Make sure to allow enough room underneath for  
any connectors that may be required. Test the fit of each control head, the tallest heads may need to be  
installed near the higher end of the console.  
2. Arrange the control heads in the console box as desired. Blank panels of various sizes have been provided to  
act as spacers between each control head, if needed. Secure in place by attaching a piece of dual lock  
fastener to each end of the blank panel and then pressing the strips of dual lock fastener on the faceplates,  
blank panels and console box together.  
3. Attach the MCS Console Box holddowns to the sides of the console box and over faceplates with (6) 10-32 x  
.38 Phillips head machine screws.  

Admiral AAW 08DR1FHU User Manual
Briggs Stratton 170700 User Manual
Brother MFC 8860DN User Manual
Carrier 39LC User Manual
Carrier 48HDT User Manual
CyberPower Systems CPS90UPA User Manual
Epson BX610FW User Manual
Goodman Mfg ATUF User Manual
Honda Automobiles Cargo Net AAM 39649 User Manual
HP Hewlett Packard COLOR LASERJET CP6015 User Manual