L7836
Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Some parts may be packed in the bassinet/storage basket.
Storage Basket
Base
Storage Basket Bottom
ꢀ Legs with Wheels
ꢀ Legs
Bassinet with Canopy
2 Small Diameter Tubes
Lower Canopy Tube
2 Large Diameter Tubes
Pad
#8 x 3/4" (1,9 cm) Screw – 10
Sheet
M6 x 40 mm Screw – ꢀ0
Note: Tighten or loosen the screws with
a Phillips screwdriver or an Allen wrench.
Do not over-tighten the screws.
Shown Actual Size
ꢀ Handles
Allen Wrench
3
2 Braces
Assembly
Leg
Leg with Wheel
CAUTION
This package contains small parts in
its unassembled state. Adult assembly
is required.
Peg
Peg
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, torn fabrics, missing parts
or sharp edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price® for replacement parts and instructions if
needed. Never substitute parts.
ꢀ
Leg with Wheel
Base
• Carefully turn the base assembly over.
• Match the number label on a leg with the number label on a
corner of the base. Fit the leg to the peg on the base.
• Insert two M6 x 40 mm screws into the leg and tighten with the
Allen wrench.
• Repeat this procedure to assemble the remaining leg with a
wheel to the other corner of the base.
Peg
Peg
Leg
1
Hint: There are numbered labels on each leg and in each corner of
the base. You will match the number on each leg to the number in
each corner on the base.
• Carefully place the base on it's side.
• Match the number label on a leg with the number label on a
corner of the base. Fit the leg to the peg on the base.
Brace
• Insert two M6 x 40 mm screws into the leg and tighten with the
Allen wrench.
• Repeat this procedure to assemble a leg with a wheel to the
other corner of the base.
3
• Turn the assembly upright.
• Position a brace so that it curves away from you.
• Fit the brace to the bottom of two legs, as shown.
• First line up the holes in the brace with the holes in the legs.
Then, insert two M6 x 40 mm screws into each leg. Tighten the
screws with the Allen wrench.
• Repeat this procedure to attach the other brace to the
base assembly.
4
Assembly
Storage Basket Supports
4
Storage Basket Bottom
Brace
• Place the storage basket bottom on a flat surface.
• Align the hole in each storage basket support with the holes
in the storage basket bottom.
• Fit the groove in a storage basket support onto the storage
basket bottom.
Storage Basket
Brace
• Repeat this procedure to attach the other five storage basket
supports to the storage basket bottom.
6
• Slide the storage basket onto the braces, as shown.
• Insert two #8 x 3/4" screws into the storage basket supports
on each end of the storage basket. Tighten the screws with a
Phillips screwdriver.
5
• Insert a #8 x 3/4" screw into each storage basket support and
tighten with a Phillips screwdriver.
Storage Basket Skirt
7
• Position the storage basket skirt over and around the top edge of
the storage basket.
5
Assembly
Bassinet Tubes
Large Diameter Tubes
Bassinet
Sockets
8
• Carefully turn the bassinet over and
place on a flat surface.
• Locate the large diameter tubes.
Large Diameter Tube
(Actual Size)
• While pressing a button on a large diameter tube, insert it into
a socket on one end of the bassinet. Push the tube until you hear
a "click".
Hint: The large diameter tubes will only fit in the large diameter
sockets on the bassinet. If the tubes do not seem to fit, try another
socket on the bassinet.
• Repeat this procedure to assemble the other large diameter
tube to the bassinet.
Base Sockets
10
• Turn the bassinet upright.
Small Diameter
Tubes
• Fit the tubes on the bassinet into the sockets in the base.
• Push down near each tube until you hear a "click".
• Pull up on the bassinet to be sure it's secure to the base.
Sockets
9
Small Diameter Tube
• Locate the small diameter tubes.
(Actual Size)
• While pressing a button on a small
diameter tube, insert it into a socket on the other side of
the bassinet.
• Repeat this procedure to assemble the other small diameter
tube to the bassinet.
6
Assembly
Hole
Lower Canopy Tube
Handle
Hole
PRESS
A
B
Ring
11
• Position a handle so that the curved edge is down.
• Fit a handle to the upper end of two legs, as shown.
• Insert an M6 x 40 mm screw into the hole in the top of each leg.
Tighten each screw with the Allen wrench.
Socket
• Repeat this procedure to assemble the other handle to
the assembly.
1ꢀ
• Locate the ring on one side of the bassinet.
• While pressing the button on the end of the lower canopy tube,
A
insert it into the ring on the bassinet
.
Hint: If the lower canopy tube does not seem to fit into the ring,
turn it over and try again!
• Insert the end of the lower canopy tube into the socket in the
B
bassinet
. Push the tube until you hear a "click". Pull up on
the tube to be sure it is secure.
7
Assembly
Pad
Sheet
Upper Canopy Tube
Lower
Canopy Tube
PRESS
Pad with Sheet
13
• Lift the upper canopy tube and smooth the canopy around the
upper canopy tube.
• While pressing the button on the lower canopy tube, fit the
upper canopy tube onto the lower canopy tube. Push until you
hear a "click".
• Pull up on the upper canopy tube to be sure it is secure.
14
• Fit the pad into the slot in the sheet.
• Place the pad with sheet into the bassinet.
8
Battery Installation
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:
Battery Compartment
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
1.5V x 4
"D" (LRꢀ0)
• Locate the battery compartment on the back of the base.
Hint: Align the notch in the base with the screw for easier
access to the battery compartment
.
• Loosen the screws in the battery compartment door with a
Phillips screwdriver.
• Insert four “D” (LR20) alkaline batteries into the battery
compartment.
• Replace the battery compartment door and tighten the screws.
Note: Low battery power may cause product movement to
slow, sound to become faint or product to turn off all together.
If this should happen, replace the batteries with four alkaline
"D" (LR20) batteries.
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
9
Gliding Bassinet
WARNING
Failure to follow these warnings and the
instructions could result in serious injury
or death.
• SUFFOCATION HAZARD - Infants
can suffocate:
- in gaps between an extra pad and the
side of the product.
- on soft bedding
- NEVER add a mattress, pillow, comforter,
or padding. Use ONLY the pad provided
by Fisher-Price®.
• FALL HAZARD - To prevent falls, DO
NOT use this product when infant begins
to push up on hands and knees or has
reached 25 lbs (11.3 kg), whichever
comes first.
• Strings can cause strangulation! NEVER
place items with a string around a child’s
neck such as hood strings or pacifier
cords. NEVER suspend strings over
product or attach strings to toys.
• Never place product near a window where
cords from blinds or drapes can strangle
a child.
• For best performance, make sure this product is used only on a
completely level surface.
• To reduce the risk of Sudden Infant Death
Syndrome (SIDS), pediatricians recom-
mend healthy infants be placed on their
backs to sleep, unless otherwise advised
by your physician.
• Use ONLY the sheet provided by Fisher-Price®
or one specifically designed to fit the
dimensions of the pad.
10
Gliding Bassinet
FCC Statement (United States Only)
FCC Statement (United States Only)
Music and Sounds
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
Power/Volume Switch
Music and Sounds Buttons
Power/Speed Dial
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
Glider
• Turn the power/speed dial to begin gliding.
Hint: In most cases, a slower setting works best for a smaller child,
while a faster setting works best for a larger child. If gliding stops
while using a slow setting, try a faster setting. Give the seat a light
push to start the gliding motion again.
• Gliding will continue for about 20 minutes and then turn off. To
start gliding again, simply turn the power/speed dial to the reset
position (off) and then back on to the desired speed setting.
• Be sure to turn this product off when not in use. Turn the
power/speed dial to the off setting
Note: If gliding motion is slow in one direction (and you hear
a winding or grinding noise), you may be using this product
on an inclined surface. Use this product only on a completely
level surface.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
O.
Music and Sounds
• Slide the music and sounds power/volume switch to on with
lower volume or on with higher volume.
Care
• Press a music/sounds selection button for music, nature or
simulated womb sounds.
• Listen to music or sounds for about 20 minutes. Press any of the
music and sounds buttons to restart music or sounds.
• The pad, frame, bassinet, storage basket and canopy may be
wiped clean with a mild cleaning solution and a damp cloth.
Do not use bleach. Do not use harsh or abrasive cleaners. Rinse
clean with water to remove residue. Do not immerse the frame.
• The sheet is machine washable. Wash it separately in cold water
on the gentle cycle. Do not use bleach. Tumble dry separately on
low heat and remove promptly.
• Be sure to turn off music and sounds when not in use. Slide the
music and sounds power/volume switch off
O.
11
CANADA
VENEZUELA
Mattel Canada Inc., 6155 Freemont Blvd.,
Mattel de Venezuela, C.A., RIF J301596439, Ave. Mara, C.C. Macaracuay Plaza,
Torre B, Piso 8, Colinas de la California, Caracas 1071.
ARGENTINA
MÉXICO
Mattel Argentina, S.A., Curupaytí 1186, (1607) – Villa Adelina, Buenos Aires.
Importado y distribuido por Mattel de México, S.A. de C.V.,
Insurgentes Sur #3579, Torre 3, Oficina 601, Col. Tlalpan,
Delegación Tlalpan, C.P. 14020, México, D.F. R.F.C. MME-920701-NB3.
COLOMBIA
Mattel Colombia, S.A., calle 123#7-07 P.5, Bogotá.
CHILE
BRASIL
Mattel Chile, S.A., Avenida Américo Vespucio 501-B, Quilicura, Santiago, Chile.
Importado por : Mattel do Brasil Ltda.- CNPJ : 54.558.002/0008-04 - Av.
Tenente Marques, 1246 - Sala 02 - 2º. Andar - 07770-000 - Polvilho -
Cajamar - SP – Brasil. Serviço de Atendimento ao Consumidor (SAC):
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2008 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA
L7836pr-0920
|