Bounce ‘n Play
Activity Dome
Model Number: 79652
Please keep this instruction sheet for future reference,
as it contains important information.
Tool needed for assembly: Phillips Screwdriver (not included).
Use only for a child who is unable to push up on hands and knees,
pull up or sit unassisted.
i
Product features may vary from picture above.
Parts
®
Metal Canopy Stay
®
Pad
2 Covers
3 Toys
(Toys may
be different
than shown.)
2 Base Wires
Base
Spring - 4
Plastic Mesh Cover Stay
13
M5 x 1 /16" Screw - 2
CAUTION
5
M6 x 1 /8" Screw - 8
This product contains small parts in
its unassembled state.
Adult assembly is required.
M5 Lock Nut - 2
M6 Lock Nut - 8
ALL SHOWN ACTUAL SIZE
3
Assembly
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.
Frame
Button Hole
Middle Hole
Middle Hole
Plastic Mesh
Cover Stay
Mesh Cover
3
Frame Tubes
• Position the ends of the frame tubes against the middle
holes in a frame.
1
Base
Rounded
Side
• Open the base and position it upright on a flat surface,
as shown.
• Locate the end of the base with the mesh cover. Insert the
entire plastic mesh cover stay into one of the button holes
in the mesh cover.
5
M6 x 1 /8" Screw - 4
M6 Lock Nut - 4
• Be sure to tuck the plastic mesh cover stay away from the
button hole in the mesh cover.
Frame
M6 Lock Nut
Frame Tube
Canopy Tunnel
Frame Tube
Metal
Canopy
Stay
4
Push Base Up
5
• Insert an M6 x 1 /8" screw through each frame tube and into
the frame.
• Fit an M6 lock nut (with the rounded side toward the fabric)
into each middle, hexagonal opening on the back of the
frame.
2
• Insert the metal canopy stay through the canopy tunnel.
Hint: You may find it easier to access the hexagonal opening
on the back of the frame if you push the base up, so that the
fabric is out of the way.
4
Assembly
Frame
5
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat assembly steps 3 - 5 to attach the other ends of the
frame tubes to the frame on the other side of the base.
7
Rounded Side
M6 Lock Nut - 4
• Fit an M6 lock nut (with the
rounded side toward the
fabric) into each lower, hexag-
onal opening on the back
of the frame.
5
M6 x 1 /8" Screw - 4
Spring - 4
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other ends of the
base wires to the frame on the other side of the base.
Frame
Lower Hole
Base
Wire
Spring
6
Base Wire
• Position the base wires around the base so that the ends
point upward and are against the lower holes in a frame.
5
• Place a spring onto an M6 x 1 /8" screw.
5
• Insert the M6 x 1 /8" screw with spring through a base wire
and into the frame.
5
Assembly
Toys
Canopy
Fasteners
Rounded
Side
13
M5 x 1 /16" Screw -2
M5 Lock Nut -2
Pad
Fastener
Metal Canopy Stay
Cover
®
Upper
Hole
9
• Fasten the pad fasteners to the base fasteners.
• Lift the canopy.
• Attach the toys to the canopy fasteners.
8
Slot
Tab
IMPORTANT! Assembly is now complete, but Bounce ‘n Play
Activity Dome is not ready for use. Please refer to the Use
instructions, on this page, beginning with step 2.
• Position one end of the metal canopy stay against the
upper hole in a frame.
13
• Insert an M5 x 1 /16" screw through the hole in the cover.
• Fit the end of the screw through the hole in the metal
canopy stay and into the upper hole in the frame.
• Push on the cover to insert and “snap” the tab on the cover
into the slot in the frame. Make sure you hear a “snap”.
• Fit an M5 lock nut (with the rounded side toward the
fabric) into the upper hexagonal opening on the back
of the frame.
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other end of the metal
canopy stay and the remaining cover to the frame on the
other side of the base.
6
Use
To Unfold
PUSH
PUSH
Frame
Groove
Base Wire
1
3
Sides of Base Wire
• Position the product upright on a flat surface.
• Grasp both sides of a base wire.
• Pull both sides of the base wire outward and then let the
base wire rotate down.
Note: If the base wire does not freely rotate down, pull the
sides of the base wire further outward.
• Push down on the product to be
sure each side of the base wire is
in the correct position. The base
wire should rest in the groove in
each frame.
CORRECT
• Repeat Use steps 1- 3 to unfold
the other base wire.
Using the Canopy
Canopy Up
Frame
Canopy
Down
Groove
Groove
2
Sides of Base Wire
• Lift the product up slightly so that each side of the base
wire “snaps” into the groove in each frame. Make sure you
hear a “snap”.
®
4
• Adjust the canopy up or down.
7
Use
Use
Using the Mesh Cover
Base Wire
Zipper
Mesh Cover Up
Canopy Up
7
®
5
• Rotate the base wire up.
• Repeat this procedure to fold the other base wire.
• Adjust the canopy and mesh cover up.
• While holding the mesh cover up, fasten the zipper closed.
Care
To Fold for Portability
The pad and toys are machine washable. Wash the pad and
toys separately in cold water on the gentle cycle. Do not use
bleach. Tumble dry separately on low heat and remove
promptly. The fabric and frame may be wiped clean using
a mild cleaning solution and a damp cloth.
Frame
Groove
Groove
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to:
6
Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone 01628 500303.
Sides of Base Wire
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond, Victoria 3121 Australia.
• Grasp both sides of a base wire.
Consumer Advisory Service 1300 135 312.
• While lifting the product up slightly, pull both sides of the
base wire outward to remove the base wire from the groove
in each frame.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
Printed in China
©2001 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
79652pr-0920
|