®
EPSON Stylus C40 Series
Insert both cartridges as shown and close the clamps.
If you see this screen, make sure the printer is
connected and turned on. Wait a few moments until
the screen disappears. Click Retry if necessary.
3
6
black
color
Start Here
When you see a message that setup is complete,
click OK.
Start Here
7
8
9
You must install both cartridges
or the printer won’t work.
When you see the EPSON Product Registration screen,
register your printer as instructed.
1
Unpack
Before you begin, make sure your computer is set up completely.
Close any open windows on your screen.
You’re ready to start printing!
Press the
maintenance button and close the printer cover. The
power light
Remove the tape and packing material from the printer.
4
1
flashes and you hear the printer charge its ink. Wait until ink charging is finished
(the power light stops flashing).
Windows 98, Me, and 2000
Your computer may have the EPSON printer software already installed.
1
remove the insert
maintenance
button
Make sure the printer is still turned on, then turn on your computer.
Don’t turn off the printer or
interrupt ink charging while
If you see this screen
Your software is already installed. Click OK.
You’re ready to start printing!
the
power light is flashing
or you’ll use up more ink
than necessary.
Peel off the tape beneath the cover
and remove the insert.
2
If you see a screen like this
Click Cancel. Then follow the steps below
to install the printer software:
Insert the paper support
into its three slots.
3
When you see the Windows icons on your monitor,
put the EPSON CD-ROM in your CD-ROM or DVD drive.
1
1
5
Load Paper
Double-click
My Computer, double-click
2
Load some paper behind the tab
on the right edge guide.
2
EPSON, then double-click EPSON.
1
Read the license agreement and click Agree.
3
4
2
Attach the Cable
Press in the locking tab on the left edge
guide and slide it against the edge of the
2
At the Main Menu, click Install Printer Driver.
The printer files install.
®
5
Shut down your computer before attaching the cable. In Windows,
click Start and select your Shut Down or Turn Off option.
Leave the computer turned off until instructed
to turn it on in section 6.
1
paper stack.
If you see this screen, make sure the printer is turned on
and connected. Wait a few moments until the screen
disappears. Click Retry if necessary.
Pull out the output tray.
5
3
3
2
Connect your USB cable to the
printer and a PC or Macintosh.
2
®
At the last installation screen, click OK.
6
7
When you see the EPSON Registration screen,
register your printer as instructed.
6
Install Software
If you’re using Windows, check to see which version you have,
then follow the right set of instructions for your system.
Close any open windows on your screen.
You’re ready to start printing!
8
3
Power On
Windows XP
Plug the printer into a grounded electrical outlet.
1
2
®
6
Your computer may have the EPSON printer software already installed.
Make sure the printer is still turned on, then turn on your computer.
power button
Macintosh OS 8.5.1 to 9.x
Press the
power button until the lights come on.
If you’re using OS X, see the Read This First booklet for instructions.
Don’t turn on the computer yet.
If you see this message in the bottom
3
Make sure your printer is still turned on, then turn on your Macintosh.
1
2
Found New Hardware
Your new hardware is installed and ready to use.
right corner of your screen
Don’t use an outlet controlled by
When you see your Macintosh icons, put the
EPSON CD-ROM in your CD-ROM or DVD drive.
You’re ready to start printing!
a wall switch or timer. Never use a
power strip switch to turn the
printer on or off; use only the
If you see this screen
Double-click the
then double-click
EPSON CD-ROM icon,
EPSON.
3
Click Cancel. Then follow the steps below
printer’s
power button.
to install the printer software:
Read the license agreement and click Agree.
At the Main Menu, click Install Printer Driver.
At the installer screen, click Install.
4
5
6
7
When you see the Windows icons on your monitor,
1
put the EPSON CD-ROM in your CD-ROM or DVD drive.
4
Load Ink
If you see a screen asking What do you want
2
Open the cover and lift the ink cartridge clamps.
Windows to do?, click Cancel.
1
2
Follow the on-screen instructions to complete
installation and restart your Macintosh.
Unpack the ink cartridges that came with your
printer and remove the yellow tape.
Click Start, click
My Computer, double-click
3
EPSON, then double-click EPSON.
After your Macintosh restarts, you see the EPSON Registration screen.
Register your printer as instructed.
8
4
Read the license agreement and click Agree.
4
5
Open the Chooser, click the C40 Series icon, click your USB port,
and turn on background printing.
At the Main Menu, click Install Printer Driver.
The printer files install.
9
Close the Chooser. You’re ready to start printing!
10
Keep cartridges out of the
reach of children.
Turn this over to start printing . . .
|