Installation Instructions
Wine Dispensing Syst
Model DYWS4
Part No. 107376 Rev. C
Important Safety Instructions
Safety Symbols and Labels
Important Information About
Safety Instructions
DAnger
Immediate hazards that wILL result in severe personal
injury or death.
•
•
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or
operating this or any other appliance.
wArnIng
Hazards or unsafe practices that COuLD result in severe
personal injury or death.
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t
understand.
CAuTIOn
Hazards or unsafe practices that COuLD result in minor
personal injury or property damage.
DAnger
nger
eLArD:
IMPOrTAnT:
•
Do not store or use combustible, flammable or
explosive vapors and liquids (such as gasoline) inside
or in the vicinity of this or any other appliance.
wer cord with damp hands.
electrical outlet the unit is connected to
essible at all times so that the appliance
plugged when necessary.
•
Use only the argon gas cylinder type specified in t
manual with this appliance. Use of any other ty
of gas or cylinder may result in explosion, fir
personal injury.
•
•
•
R unplug the appliance by pulling on the power
d. Always grip the plug firmly and pull it straight out
rom the electrical outlet.
If the appliance is faulty, do not attempt to repair it
yourself. Turn it off, unplug it from the electrical outlet
and call a qualified service technician.
wArnIng
Failure to follow the instructions i
may result in personal injury, d
appliance. Dacor cannot be amage
to property or injury to pee to
comply with the safety and tions
contained in this handbook.
Do not operate or install the appliance if the power
plug or power cable is damaged or frayed. Have it
replaced only by a qualified service technician.
When moving the appliance away from the wall, be
careful not to roll over or damage the power cord.
reAD AnD SAve THeSe InSTruCTIOnS
1
Important Safety Instructions
General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety
precautions, including the following:
wArnIng
wArnIng
•
•
•
If the appliance is damaged, immediately contact the
dealer. Do not install or use a damaged appliance.
•
Do not place your hands or fingers in area of moving
parts. NEVER place fingers or hands into the bottle
bay assembly. Personal injury may result. Call a
qualified service technician to diagnose any problems
in the bottle bay assembly or behind enclosed panels.
This appliance must be properly installed according to
these installation instructions before use.
Install this appliance only on a flat, level surface
capable of supporting the appliance’s weight. Operate
it only in the upright position.
•
•
Only allow individuals to use the wine dispensing
system who are able to operate it properly.
Never allow anyone, including children, to sit, stand,
or climb on any of the appliance. Doing so may
cause damaginjury or death. Do not allow
children to ntrols or touch other parts
of the a
•
•
Read the accompanying use and care manual
completely before operating this appliance.
The installer must show the customer the location of
the electrical outlet and how to disconnect power to
the wine dispensing system.
•
•
Do nntrols.
•
•
Do not install, repair or replace any part of the
appliance unless specifically recommended in
the literature accompanying it. A qualified service
technician should perform all other service.
nly in the manner indicated in
anual and use only the cleaning
steam or pressure cleaner to clean the
nsing system or any part of it. Damage
by cleaning the unit in this manner could
in electric shock, fire or explosion.
Before installing, cleaning or performing any type of
service or part removal, turn the unit off and make
sure that the appliance power plug is disconnec
from the electrical outlet or power is disconn
the circuit breaker panel or fuse box.
o avoid an electric shock hazard or other personal
injury, do not put body parts or any other objects into
any opening, air vent, the base grille or bottom of the
appliance.
•
Use only the gas cylinders designed fo
this product. They are specified in t
manual.
•
•
Care should always be taken when handling
pressurized gas. Make sure the proper tubing and
shut-off valves are always used.
•
•
Keep all packaging materials
Plastic sheets and bags ca
Use this appliance only for a home
appliance as outlined in the umanual.
This appliance is not intended foercial or
industrial use.
This appliance is not suitable for installation in an
area where a water jet could be used.
•
To prevent bursting, do not expose the argon gas
cylinders to open flame. Store and use the cylinders
at temperatures below 130°F (54°C). Do not dispose
of the gas cylinders in fire or an incinerator.
•
•
Store and use the appliance and the argon gas
cylinders only in areas with adequate ventilation. Do
not directly inhale argon gas.
Do not leave children alone or unattended in the
area around the appliance. Do not allow children to
play with the controls, to open and close the doors or
touch other parts of the appliance. Keep gas cylinders
out of reach of children.
2
Installation Specifications
wArnIng
•
•
Observe all governing codes and ordinances during planning and installation. Contact your local building department
for further information.
For safe and proper operation, all the requirements in the Installation Specifications section including, but not
limited to, the electrical specifications, minimum clearances and cabinet specifications must be met or exceeded.
All product tolerances are ±1/16” (±1.6 mm)
unless otherwise stated.
Technical Specifications/Dimensions
Bottle capacity
4
Power supply input
requirements
120 Vac, 60 Hz., 2 Amps.
16”
(40.6 cm)
120 Vac, 60 Hz., 10 Amp. 3-wire*
dedicated, grounded, circuit required
Circuit requirement
Power cord length
Gas tubing length
Appliance weight
74” (188 cm)**
117” (297 cm)***
80 lbs. (32 kg) empty
Operating (room)
temperature
Min. 50°F (10°C)
Max. 80°F (26.7°C)
* Hot (L1), Neutral (N1), Ground
** Usable length = 48 inches
*** Usable length = 72 inches
19 9/16”
(49.7 cm)
9 5/16”
(23.7 cm)
3 13/16”
(2.1 cm)
3 13/16”
(2.1 cm)
24 5/8”
(62.5 cm)
rear view
25 5/8”
(65.1 cm)
Leveling feet
Adjustable 1” to 4”
(2.5 cm to 10.2 cm)
Front view
* WineStation is a registered trademark of Napa Technology
3
Installation Specifications
•
The electrical outlet for the wine dispensing system
must be located to allow for easy access when the unit
is installed for easy disconnection.
Electrical Requirements
wArnIng
•
•
Use an electrical outlet which cannot be turned off with
a switch or pull chain.
To prevent an electric shock hazard, the electrical outlet
and supply must meet the specifications stated below.
It is the owner’s responsibility to make sure that the
electrical service meets electrical requirements and that
the electrical outlet has been properly installed by a
licensed electrician.
Installation of an external UPS with backup battery is
recommended so that the unit does not need to be
reset after a power outage.
Location Requirements
IMPOrTAnT: The power supply for this appliance is
equipped with a three prong grounding power plug for
protection against possible electric shock hazards and
fire. It must be plugged into a dedicated, grounded
electrical outlet. If only a two prong electrical outlet is
available, it is the responsibility of the customer to have
it replaced with the proper type by a licensed electrician.
Do not under any circumstances:
wArnIng
electric Shock Hazard: Due to the possibility of
spillage during normal use, DO nOT install this
appliance above elow any other appliance.
•
•
•
To prevent tit install this appliance in an
unrestraincabinet.
•
Cut or remove the third (ground) prong from the power
cord.
Install a flat, level surface
capappliance’s weight. Operate
it sition.
•
•
•
Use an adapter plug.
Modify the power cord.
•
esigned for indoor use. It may be
rovided it is installed under cover in a
nd operated within the required ambient
perature (see page 3)
Connect the appliance to an extension cord.
imum and minimum dimensions and clearances
he facing page must be met or exceeded for safe
peration and for proper fit in the cabinet.
When determining the installation location, look for a
location that is free of potential safety hazards that
might interfere with the installation or operation of the
unit or interfere with air circulation around the unit. The
location needs to be clean, dry and free of any debris.
Power cord with
three prong plug
el
•
A minimum area or cabinet opening of 13” H x 9” W x
4” D (33 cm H x 23 cm W x 10 cm D) must be provided
in a nearby for the gas cylinder, regulator and gas line
(with fittings) that supply Argon gas to the unit. An area
deeper than this is recommended to allow storage
of additional gas cylinders. The unconnected gas
cylinders are for
•
•
The three prong electrical outlet for his appliance must
be located within 48” (122 cm) of the unit to make sure
the power cord can reach.
The electrical outlet installation, including minimum
supply wire size and grounding, must be done in
accordance with National Electric Code ANSI/NFPA
70 and local codes and ordinances. A copy of this
standard may be obtained from:
9 1/2” H x 2.5” W (24 cm H x 6.5 cm W).
•
•
The included gas supply line (with fittings) allows for
the cylinder storage area to be as far as 6 feet from the
wine dispensing system. Holes in adjoining cabinets
between the wine dispensing system and the gas
cylinder location must be 1 1/8” (2.9 cm) in diameter to
allow the gas line and its fittings to pass through.
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269-9101
The wine dispensing system must be installed at a
safe distance from sources of heat, such as home
appliances, in order to avoid an excessive rise in
temperature.
•
The correct voltage, frequency and amperage must
be supplied to the electrical outlet from a grounded,
dedicated, single phase circuit that is protected by a
properly sized circuit breaker or time-delay fuse. If one
is not installed, call a licensed electrician. See page
3 for the circuit requirements.
4
Installation Specifications
1” (2.5 cm)
min.
Allow for Proper Air Ci
All cabinet tolerances: +1/16” (+1.6 mm) -0
unless otherwise stated.
16” min.
(40.6 cm)
19 11/16” min.
(50.0 cm)
Minimum Clearance requirements
5
Installation Instructions
Unpacking the Appliance
wArnIng
•
If the electric outlet provided does not meet the
specifications on pages 3 and 4, do not
proceed with the installation. Call a licensed
electrician to install the proper electrical service before
proceeding.
1. Move the box to the installation location. The wine
dispensing system is package with the display window
facing up towards the box opening.
2. Open the box along the taped closure.
3. Remove the (4) four leveling feet from the plastic bag,
taped to the top of the unit.
•
•
excessive weight hazard - Use two or more people
to move and install the wine dispensing system.
Failure to do so can result in back or other injury.
4. Remove the foam brace, along each side. You will find
spacing to allow for a firm grip of the unit, so that you
may lift it straight out of the box and onto its back on
a flat counter or surface. nOTe: Resting the unit on
its back will not harm the system and allow for proper
attachment of the leveling feet.
Protect your countertop and installation area! When
moving the wine dispensing system during installation,
cleaning and or service, always lift and pull the unit
straight out. Do not wiggle or walk the unit, because it
may damage the countertop or the product.
5. Once the levelint have been firmly secured, lift the
wine dispensiinto the upright position.
•
•
To avoid personal injury, use only the included gas
pressure regulator or a Dacor specified replacement.
6. Make sure roperly leveled. If
necesseling feet on the bottom
of thin the appropriate direction.
Ae bottom of the unit is at least
countertop.
DO NOT remove the leveling feet or place the unit
in the upright position without the feet attached. The
feet must be adjusted so that there is a minimum of 1”
(2.5 cm) below the unit for proper ventilation. Failure
to attach and properly adjust the feet will void the
warranty and may cause countertop damage.
ront of the final installation location.
Verify the Package Contents
Check to make sure all the parts listed below are
in the shipping box. See the use and care man
parts and accessories.
IMPOrTAnT: The required argon gas
shipped with the system and must
Dacor Customer Service at (82. Your
first gas argon gas cylinder is parge.
•
•
•
•
•
•
•
•
•
•
•
•
Gas regulator assembly (1)
Dispensing heads (6, equipped wited gaskets)
Extra dispensing head gaskets (3 white, 2 green)
Plastic gas tubing with fittings (1)
Leveling feet (4)
1” (2.5 cm)
min.
Pickup tubes (10)
Food grade silicon spray (1)
Power cord (1)
Head selection tool (1)
Keys (2)
Drip cloth (1)
Use and care manual
Make sure you have all required tools for installation before
proceeding.
6
Installation Instructions
4. Plug the power cord (provided) into the power plug on
Installation
the power supply (black rectangular box) mounted on
the back of the wine dispensing system.
wArnIng
5. If required, route the power cord though any access
holes drilled in the adjoining cabinets.
•
•
To avoid personal injury, use only the included gas
pressure regulator or a Dacor specified replacement.
6. Make sure the cable coming from the power supply
(opposite the power cord that connects to the wall) is
connected to the Power Input connector on the back
of the unit. Also, check to make sure that both of the
micro-switches located on the back of the unit are in
the up position.
Do not use any power supply other than the one
provided with the system or a Dacor approved
replacement. Do not attempt to modify or bypass the
power supply.
1. Before installation, make sure any access holes for
the power cord and gas tubing have been drilled in
adjoining cabinets as necessary to allow them to
pass through to the electrical outlet and gas cylinder
location.
7. Slowly and gently lift the unit up and back into the final
location. As you do this, have someone gently pull the
gas tubing and power cable through the access holes
into the adjacent cabinets (if necessary). Exercise care
to make sure he wiring and tubing lines do not
become dake sure the require 1” (2.5 cm)
space ive and below the unit.
2. Plug one end of the plastic gas tubing (provided)
into the inert gas connector at the back of the wine
dispensing system.
3. If required route the plastic gas tubing though any
access holes drilled in the adjoining cabinets.
These connectors
used by qualified
service personnel on
Connect power
supply output
here
Plastic gas
tubing
120 Vac
power cord
Power
supply
Inert gas
connector
Connect to
120 Vac 60 Hz.
electrical outlet
7
Installation Instructions
8. Find the gas regulator assembly shipped with the
unit.
Regulator
adjustment
knob
9. Make sure the regulator adjustment knob is turned
all the way in the OFF direction.
10. Plug the end of the gas tubing leading to the wine
dispensing system into the gas regulator assembly.
11. Remove the plastic cap from the top of the argon
gas cylinder (must be ordered separately, see page
6).
12. Insert the top of the gas cylinder into the bottom of
the gas regulator assembly and turn it clockwise
until it is snug. Do not overtighten.
Gas supply
line from wine
dispensing
system
Regulator
assembly
13. Turn the regulator knob in the On direction until it
stops.
14. Open the door on the front of the unit. Swing the
spout cover to the up position.
15. Make sure the power switch, located on the left
side of the bottle bay, is slid all the way down, to
the OFF position.
16. Plug the power cord into the electrical outlet.
17. Slide the main power switch all the way up to the
On position.
Switch Positions
ON
RESERVED
NOT USED
OFF
For use by
authorized
service
personnel only
Main Power Switch
(under spout cover)
Spout cover
release lever
(on bottom of
spout cover)
18. The unit will run through a series of self-tests,
which will take several seconds. Once this process
is completed, the blue lights on the control panel
will come on, indicating that the wine dispensing
system is ready for use. IMPOrTAnT: When the
system is powered up for the first time, LOCKeD
will appear on the display. See Unlocking the
Control Panel in the operation section of the use
and care manual for unlocking instructions.
19. Push up on the spout cover release lever on the
bottom of the spout cover. Hold the lever up as you
lower the cover down into place. CAuTIOn: Do not
push down on the spout cover without pushing up
on the lever. Damage to the lever will result.
20. Once the spout cover is closed, close the bottle
bay door. Push in slightly just above the lock until it
snaps shut.
8
Installation Instructions
Installation Checklist
wArnIng
To ensure a safe and proper installation, the installer
must complete the checklist below to ensure that no part
of the installation has been overlooked.
Proper installation is the responsibility of the homeowner.
The importance of proper installation of your appliance
cannot be overemphasized.
‰ Has enough space been provided around the unit to
allow for proper ventilation? See page 5.
‰ Is the countertop strong enough to hold the weight of
the unit? See pages 3 and 4 .
‰ Does the electrical supply meet specifications. See
page 4.
‰ Is the power output cable from the power supply
connected to the back of the unit? See page 7.
‰ Is the plastic gas supply tubing attached to the back of
the unit? See page 7.
‰ Is the wine dispensing system connected to the
dedicated, grounded, three prong electrical outlet? Se
page 8.
‰ Is the gas supply tubing connected to the gas re
assembly? See page 8.
‰ Is the gas regulator assembly attached to
gas cylinder? See page 8.
‰ Is the gas regulator knob in the full
page 8.
‰ Has the warranty been activaranty
card filled out completely
|
