IMI CORNELIUS INC.
One Cornelius Place
Anoka. MN 55303-6234
Telephone (800) 238–3600
Facsimile (763) 422–3246
WATER TANK SEAL KIT (P/N 308979000)
on
UNIVERSAL C-750 PRE-MIX DISPENSER
These Instructions outline installation of the Water Tank Seal Kit (P/N 308979000) on the Universal C-750
Pre-Mix Dispenser.
1
1
3
2
NO TAG
4
5
INSULATED
REFRIGERATION
LINE
DISPENSER
November 13, 2002
185211001
IMI Cornelius Inc, 1989–2002
Revision: A
NOTE: Only qualified personnel should install this kit.
1. Unpack loose–shipped parts. Make sure all parts are present and in good condition.
Table 1. Loose-Shipped Parts
Item
No.
Part No.
200468012
308981044
308982044
313093000
172127000
960265000
960115000
Name
Sheet Metal Screw, Phil Truss Hd, No. 8 by 3/4-in.
Front Cover Plate
Qty.
12
1
1
2
3
Back Cover Plate
1
4
Plug, 2-in.
1
5
Plug
1
6
Permagum Sealer,12-in. long
Rubatex Insulation,1/8 by 1/2-in. (78-in. long)
1
8
1
INSTALLING WATER TANK SEAL KIT
IMPORTANT: This kit is intended to seal the water tank to prevent leakage from splashing water when
moving or transporting the Dispenser. IT IS NOT INTENDED THAT THE DISPENSER MAY BE LAID ON
IT’S SIDE WHEN WATER TANK IS FULL OF WATER.
1. If Dispenser is in operation, place power switch on back of Dispenser in ‘‘OFF’’ position.
2. Remove four screws securing Dispenser top cover, then lift cover straight up and off.
NOTE: Front of Dispenser is the side facing the dispensing valves.
3. Place RUBATEX INSULATION (item NO TAG) all the way around outer edges of FRONT COVER PLATE
(item 2) and BACK COVER PLATE (item 3) as shown in illustration. FILL ANY GAPS AT BUTT EDGES
OF RUBATEX INSULATION WITH SMALL PIECES OF PERMAGUM SEALER (item 6).
4. Place FRONT COVER PLATE (item 2) in position on top of water tank as shown in illustration. IT MAY BE
NECESSARY TO VERY CAREFULLY REFORM OR REPOSITION INSULATED REFRIGERATION LINE
ANGLE TO FIT INTO CUTOUT AREA IN CORNER OF FRONT COVER PLATE.
5. Secure back side of front cover plate to agitator motor support plate with four THREAD CUTTING
SCREWS (item NO TAG).
6. Secure rest of front cover plate to plastic motor tank rim with six SHEET METAL SCREWS (item 1). DO
NOT OVERTIGHTEN SCREWS INTO PLASTIC.
7. Place BACK COVER PLATE (item 3) in position on top of water tank as shown in illustration.
8. Secure front side of back cover plate to agitator motor support plate with four THREAD CUTTING
SCREWS (item NO TAG).
9. Secure rest of back cover plate to plastic water tank rim with five SHEET METAL SCREWS (item 1). DO
NOT OVERTIGHTEN SCREWS INTO PLASTIC.
10. Place PLUG (item 4) in agitator motor plate water fill hole.
185211001
2
11. If installing kit on a four-flavor Dispenser, install PLUG (item 5) in 1/2-inch hole in top of agitator motor
plate.
12. Fill area between insulated refrigeration line and cutout area in front cover plate with PERMAGUM SEAL-
ER (item 6). Also, overlap front cover plate and insulated refrigeration line with permagum sealer to prevent
water leak.
13. If new Dispenser installation, refer to manual provided with Dispenser and complete installation as
instructed.
14. Install Dispenser top cover and secure with four screws.
15. If Dispenser was in operation before start of Kit installation, place power switch in ‘‘ON’’ position.
3
185211001
|