Cornelius 569000261 User Manual

IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303-6234  
Telephone (800) 238-3600  
Facsimile (800) 535-4231  
INSTALLATION INSTRUCTIONS  
DISPENSING VALVES KEYED LOCK-OUT SWITCH KIT (P/N 569000262)  
ON  
VANTAGE POST-MIX DISPENSERS  
Read and understand these instructions thoroughly before installing this Dispensing Valves Keyed Lock-out  
Switch Kit (P/N 569000262) on the Post-Mix Dispensers. The purpose of the Keyed Lock-Out Switch is to shut  
off electrical power to the dispensing valves to prevent dispensing of product. Retain these instructions as part  
of your equipment manual.  
LOOSE-SHIPPED PARTS  
Note: Only qualified personnel should install this Kit.  
Unpack and inspect kit. Make sure items are present and in good condition.  
Table 1. Loose-Shipped Parts  
Name  
Item  
No.  
Part No.  
560003869  
560003870  
318948000  
318949000  
318569000  
569000261  
Qty  
1
1
Wiring Harness  
Template, Hole Drilling  
Lock Key  
2
1
3
1
4
Hex Nut  
1
5
Key-Lock Switch  
Installation Instructions  
1
6
1
KIT INSTALLATION  
WARNING: To avoid possible fatal electrical shock or serious injury to Installer, make sure  
Dispenser is disconneced from power source before attempting to install this kit.  
1. Disconnect electrical power from the Dispenser  
2. Remove hood from the Dispenser, then lift hood straight up off the Dispenser for access to the transformer  
on the refrigeration deck.  
3. Refer to Figure 1 for location of hole to be drilled in the Dispenser hood for installation of the KEY-LOCK  
SWITCH (item 5).  
4. Place TEMPLATE, HOLE DRILLING (item 2) in position on Dispenser hood as shown in Figure 1.  
5. Drill hole in Dispenser hood as indicated on the hole drilling template, then remove template from the hood.  
Revised: October 9, 2003  
February 9, 1999  
569000261  
EIMI Cornelius Inc; 1999–2003  
HOOD  
TEMPLATE  
(ITEM 2)  
KEY-LOCK SWITCH  
(ITEM 5)  
LOCK KEY  
(ITEM 3)  
HEX NUT  
(ITEM 4)  
1.50  
FIGURE 1. DISPENSER HOOD  
6. Install KEY-LOCK SWITCH (item 5) in the hood as shown in Figure 1 and secure with HEX NUT (item 4).  
7. Refering to Wiring Diagram (Figure 2) disconnect black electrical wire, with push-on terminal on its end,  
from terminal on the transformer outlet.  
8. Connect black electrical wire, disconnected from the transformer outlet terminal, to mating electrical wire  
terminal on the WIRING HARNESS (item 1).  
9. Connect other electrical wire of the wiring harness to output terminal on the transformer where the black  
electrical wire was disconnected from in step 7 preceding.  
10. Connect other two wiring harness terminals to two terminals on the Key-Lock Switch.  
11. Install hood on the Dispenser.  
12. Connect electrical power to the Dispenser, then check Dispenser for proper operation.  
13. Insert LOCK KEY (item 3) in key-lock switch, then check Dispenser for proper operation.  
MATING  
TERMINALS  
BLACK  
WHITE  
KEY-LOCK SWITCH  
(ITEM 5 )  
FIGURE 2. WIRING DIAGRAM  
569000261  
2

Agilent Technologies 6834B User Manual
Brother PT 9400 User Manual
Canon Wireless Photo All In One 8331B002 User Manual
Continental Electric CE11155 User Manual
Epson P50 User Manual
Field Controls TB26TB User Manual
Friedrich MR24C3G User Manual
Haier ESA424K User Manual
Harbor Freight Tools 95409 User Manual
Harbor Freight Tools CENTRAL MACHINERY 95288 User Manual