Start Here
Easy Setup Instructions
Photo All-in-One
• Please confirm the included items against the illustration printed on the lid of the packing box.
• A USB cable is necessary to connect the machine with your computer.
Unpack the Machine
QT5-0683-V02
1
Prepare the Machine
2
Install the Print Head
3
Install the Ink Tanks
4
Align the Print Head
Hardware setup and Print Head
alignment is complete.
a
Place the machine on a flat and
horizontal surface, and do not place
any objects in front of the machine.
Open the Sheet Feeder Cover and
pull the Paper Support, then the Paper
Output Tray and open the Output Tray
Extension.
dUse the {or }button on the
aRemove the Print Head from its
aPeel back the orange tab completely
and remove the plastic wrapper from
the ink tank.
aPinch the Paper Guide and slide it to
Operation Panel to select the language
for the LCD, then press the OK button.
package.
the left end.
Paper Support
Extension
Caution
Before turning on the machine, remove all of the
shipping tapes.
If the orange-colored protective film is not removed
completely, problems with printing may occur.
(1) Press the {or }
button to select the
language.
Caution
Paper Guide
There may be some transparent or light blue ink
on the inside of the bag the print head comes in,
or the inside of the protective cap - this has no
effect on print quality. Be careful not to get ink on
yourself when handling these items.
Important
bTwist off and discard the orange
protective cap located on the bottom of
the ink tank.
Do not connect the USB cable until after the soft-
ware is installed.
(2) Press the OK
Note
button.
Protective Cap
Do not press!
To open the Paper Output Tray, put your finger in the
rounded indent of the tray and open it gently.
bRemove the orange protective cap from
Ink Port
Important
the Print Head and discard it.
If an unintended language is displayed on the
LCD, press the Back button to return to the Lan-
guage selection screen.
Electrical Contacts
Once the message “Install the print head and
set the ink tank.” appears, go to e.
Electrical Contacts
bLoad a sheet of letter- or A4-sized
blank paper in the Auto Sheet Feeder,
align the paper with the right side of
the Cover Guide, then slide the Paper
Guide against the paper stack.
Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
eOpen the Scanning Unit (Printer Cover)
until it locks into place. The Print Head
Holder moves to the center.
cInsert the ink tank into the right-hand
Protective Cap
Print Head Nozzles
b
Plug the power cord in the back of the
machine and connect the other end to
the wall outlet.
slot and press the
mark on the ink
Paper Guide
Note
tank until it clicks into place.
Do not touch the print head nozzles or the electrical
Print Side
contacts.
cFirmly raise the Print Head Lock Lever
until it stops.The Print Head Lock Lever
may feel heavy.
Cover Guide
Scanning Unit (Printer Cover)
Easy-Scroll Wheel
Turn the Easy-Scroll Wheel
left or right to easily select
a menu or a setting item.
For details, refer to “Basic
Operation for the Operation
Panel” in the Quick Start
Guide.
Important
c
Make sure that Yes is selected in the
message requesting head alignment,
then press the OK button.
Make sure that the Document Cover is closed.
cOpen the Operation Panel, then press
the ON/OFF button to turn on the
machine.
dMake sure the ink lamp lights red.
dInsert the Print Head.
Refer to the color
guide on the Print
Head Lock Lever.
Important
* You can also use the {,
}, [, or ]button to
select.
For your safety, always firmly grip the areas il-
lustrated when opening the Scanning Unit (Printer
Cover).
Do not touch!
fOpen the Inner Cover. Write down
the serial number located inside the
machine. You will need this to register
your product.
eClose the Inner Cover and the
eLower the Print Head Lock Lever
Scanning Unit (Printer Cover).
carefully.
Note
Print Head alignment takes about 6 minutes to
complete. Do not start another operation here.
The pattern is printed. And Print Head is aligned
automatically.
OK
Cassette
Important
Inner Cover Serial Number Location
For information on how to load paper in the
Cassette, refer to “Loading Paper in the
Cassette” in “Loading Printing Paper” of the
Quick Start Guide.
If the Scanning Unit (Printer Cover) is left open
for more than 10 minutes, the Print Head Holder
moves to the right. Close and reopen the Scanning
Unit (Printer Cover) to return the Holder to the
center.
Note
• The pattern is printed in black and blue.
• When Automatic Print Head Alignment cannot be
executed correctly, the message “Auto head align
has failed.” is displayed on the LCD. Refer to “Error
Message is Displayed on the LCD” in the User’s
Guide on-screen manual.
Important
• For your safety, always firmly grip the areas il-
lustrated when closing the Scanning Unit (Printer
Cover).
• The machine starts operating. Wait about 2 min-
utes until the machine stops making noise.
|