Introduction
Congratulations on your purchase! With both a wired LAN router and a 811g wireless access point,
the AirStation WHR-G125 Cable/DSL Router is perfect for linking your wireless devices with a
wired network and each other.
System Requirements
• A high-speed (Broadband) Internet connection or existing local area connection.
• A computer with a network connection (wired or wireless) and a good web browser. The
screenshots in this manual were taken with Firefox, but Netscape and Internet Explorer
are also supported in versions 4.5 or later, and Safari 1.0 and later are supported with
Macintosh OS X 10.2 and later.
AirStation WHR-G125 Package Contents
• WHR-G125 Wireless Router
• AC adapter and power cable
• CAT5 LAN cable
• Utility CD with Manual
• Quick Setup Guides
• Warranty Statement
ꢁ
Initial Setup
Begin by finding a good place to set up your router/access point. Some things to
consider:
• You’ll need to be able to plug your internet connection into it, so it should go within
reach of the LAN cable from your DSL or Cable modem. You’ll also want a power outlet
nearby.
• Keep the access point as central in your work area as possible. Signal strength and
speed fall off with distance.
• Higher is often better. For instance, set it up on the top shelf of a bookcase rather than
the bottom one, if possible.
• The antenna usually works best if oriented to point straight up.
Do you need a password or other information to log in to your internet connection?
Many DSL connections require information like global IP address, subnet mask, default
gateway address, DNS server address, or PPPoE parameters in order to connect. Cable
modems usually don’t require extra information. If
you have a DSL internet connection, make sure
that you have any necessary information
handy before you continue. Your Internet
Service Provider can give you this
information if you don’t know it.
ꢂ
Connecting your AirStation
Power to outlet or
surge protector
PC
Cable or DSL Modem
ꢃ
Setup with AirNavigator CD
For a simple installation, you may use the AirNavigator CD in your package to step
you through configuration. Insert the CD in the drive of your computer and follow the
directions.
The installation program will step you through connecting your computer to the
AirStation and the Internet.
ꢄ
Manual Configuration
To configure your router manually, use a wired connection to your computer. Once
you’ve connected to the internet through the router, you may switch to a wireless
connection if desired.
The computer used to configure the AirStation should be set to obtain an IP address
automatically using a DHCP server (this is Windows’ default). The WHR-G125 has a
default LAN IP address of 192.168.11.1 and Subnet Mask of 255.255.255.0.
1. Power down the Cable or DSL modem and the computer which will be used to
configure the AirStation router.
2. Plug the Cable or DSL modem’s Ethernet cable into the AirStation’s WAN port.
Initially, you may need to unplug this cable from your computer, hub or other router.
3. Plug the provided Ethernet cable into a LAN port on the AirStation and plug the other
end into your computer’s Ethernet adapter (NIC).
4. Important: turn everything on in the correct order!! Power on your cable or DSL
modem and wait one full minute, then power on the AirStation router and wait one
full minute, and finally power on the computer which will be used to configure the
AirStation.
ꢅ
Log in to the Configuration Tool
Launch a web browser on the computer that you’re
using to configure the AirStation.
The first time your router is powered on, the window
below should open automatically. To open it manually,
you may enter your routers IP addrees (192.168.11.1
by default) into the URL field.
A window will open, prompting you to enter a User ID
and Password.
Enter root as the user name and leave the password
field blank.
ꢆ
Detecting Your Broadband Connection
Your AirStation’s SmartRouter technology will determine the type of internet
connection you have automatically, and ask you for any needed information. If
your ISP assigns IPs automatically (most cable providers do), their DHCP server
will give your router an IP address. If additional login information is required
to connect to the internet, the wizard will ask for it. Enter any required login
information if asked. Contact your
DSL provider for any missing login
information.
If you need to relaunch the Internet
Connection Wizard, just click on Run
Internet Connection Wizard under
Basic Settings.
Congratulations! You are now connected to the internet. Open a familiar web
page to make sure everything is working correctly.
ꢇ
Connecting Wireless Clients to the Access Point
To connect wireless devices to
the AirStation, you may either
enter the SSID and encryption key
manually, or you can use AOSS.
For more information on AOSS, see
pages 14 and 15.
Consult your wireless clients’
manuals for instructions on
configuring them manually. You
can get SSID and encryption
information from the AirStation’s initial setup screen, as shown above. The
default SSID is the wireless MAC address, available from the lable on the side
of the AirStation. The default encryption is disabled. If you prefer to use
encryption and/or a different SSID, you may change these default settings
under Basic Settings at the top left of the page.
10
Basic Setup Page
You can get back to the Setup page
from anywhere in the configuration
screens by clicking on the Setup
tab in the top left corner. From
here, you can rerun the Internet
Connection Wizard, change your
router mode, initiate AOSS or WPS,
and see your wireless SSID and
encryption settings.
Context sensitive help is available
on the right side of each page.
11
Navigating the Menus
The menus in the Configuration Tool let you change your AirStation’s settings. To
navigate settings, choose a category at the top of the page and then a submenu
below. Settings will appear on the left, help files on the right. This example
shows the WAN/LAN category with the Internet submenu item selected.
Categories
Submenus
Individual
Help and
Settings
Instructions
The following pages show examples of some screens from the configuration utility.
1ꢀ
Initialize/Reboot
The Initialize/Restart page can be
reached by choosing the Admin
Config catagory tab and then clicking
on the Initialize/Restart submenu.
Click Restart Now from this page
to restart your AirStation. Click
Initialize Now to restore your
AirStation to factory defaults and
restart it.
You may also initialize your
AirStation by holding down the Reset
button for 3 seconds.
1ꢁ
AOSS
You can get to this page by selecting the
Wireless Config category and choosing the
AOSS submenu.
The blue AOSS button at the top left of the
page has the same function as the physical
AOSS button on the top of the router: it
initiates the AOSS process.
If all your clients support AOSS, it’s very
simple to set them up. Press the AOSS
button on the router, or the one on this page,
and then push the AOSS button on the client
device.
Each client device will have to be set up seperately. Wait for each AOSS process to finish
before starting the next one.
You can also activate AOSS by pushing the button on the top of your AirStation (see page
15). Consult your client device’s documentation for the location of its AOSS button.
If you’ve used AOSS to configure some wireless clients, and now want to add other wireless
clients that don’t support AOSS to your network, this screen will give you the information
you need to connect them manually.
1ꢂ
AOSS
AOSS (AirStation One-Touch Secure System) is a simple system for
configuring your wireless network securely. If your router and your
client device are installed and both support AOSS, then making a
secure wireless connection between them is very easy.
Push the AOSS button on the side of your router and hold it in for a few seconds. The
AOSS light will begin to flash amber. You now have two minutes to push the AOSS button
on your client device and finish the connection.
If you have a standalone client device,
it will probably have a little red button
labled “AOSS” on it. Push the button!
About 15 seconds later, you’ll have a
secure network connection.
If your client device is
a
PC card,
CardBus, or PCI adaptor, the AOSS
button will probably be in its Client
Manager Software. Check your client
device’s user manual for instructions
on where to push or click the AOSS
button.
standalone
client device
PC card
Client Manager
Software
After you’ve pressed both buttons, it will take about 15 seconds for the connection to
complete. When it’s finished, the AOSS light witll glow a solid amber. You now have a
secure network connection!
1ꢃ
AOSS Notes
Some things to keep in mind with AOSS:
• Only one AOSS wireless client adapter can be configured with the AOSS router at a
time. The buttons will need to be re-pressed to connect each additional AOSS wireless
client adapter.
• It is not necessary to AOSS client devices that have already been configured via AOSS,
unless significant changes have been made to the wireless network.
• Do not attempt to configure two separate AOSS networks at the same time, as it may
cause undesired configurations.
• If an undesired client has connected via AOSS, it can be disconnected from within the
WHR-G125’s configuration GUI.
1ꢄ
Router Mode
This AirStation supports quickly changing the
product from a wireless router to a conventional
access point.
For normal use, leave the “Router” switch in the ON
position.
If the Router switch is moved to OFF, the default IP
address of the AirStation changes from 192.168.11.1
to 192.168.11.100, and DHCP, NAT, and the WAN
port are disabled.
Turning this switch off might be desirable if you’re
adding wireless capability to an existing network
with a router. It is not suitable for most home configurations. If you plan to use the
AirStation as an normal wireless router, make sure that this switch is in the normal (ON)
position!
1ꢅ
Encryption and Security
By default, encryption is not enabled on the
AirStation unless you used AOSS to perform your
setup. Anyone within range can easily connect to
your wireless network. This might not be what you
want.
Buffalo recommends enabling encryption and
setting a password for access to your network. This
is easy to configure from within the AirStation’s
configuration tool. Select the Wireless Config tab
and the Security submenu. Use the strongest form of
encryption that all of your clients support.
1ꢆ
Encryption and Security
Many kinds of encryption are available. WEP
works with almost everything. WPA2-PSK is
much more secure. Choose the strongest method
of encryption that works with all of your wireless
devices.
If you must use WEP, it is available under “Wireless
Encryption”.
Enter a network key (“password”) for this
connection. Write down your password and put
it in a safe place. You will not be able to connect
wireless devices to your network without this
password.
1ꢇ
Encryption and Security
Each of your wireless clients will need your
password to connect to the network. Click on the
wireless icon in your computer’s systray, or this
message if it pops up.
Any wireless networks available in the area will be
listed as available. Click on your wireless network
SSID so that it turns blue and then click on Connect
at the bottom right.
ꢀ0
Encryption and Security
Enter your network key (“password”) twice and click
Connect.
Repeat for each Windows XP computer that
connects to your network wirelessly.
Other wireless devices may have different configuration requirements. Consult their
documentation for instructions on how to enter your network key and connect them to your
wireless network.
ꢀ1
Connecting to a Preexisting Network
Add an AirStation without changing your existing LAN configuration
1. Set the AirStation into Access Point Mode by moving the Router switch from ON to
OFF.
2. Connect one of the AirStation’s LAN ports to an existing router or switch on your
network. Nothing should be plugged into the WAN (“Internet”) port.
3. Open LAN Settings - LAN Port Settings and configure the following settings:
IP Address =[192.168.11.137] (Specify an unused network address from the existing
LAN.)
Subnet Mask=[255.255.255.0] (Use the same Subnet Mask as the existing LAN.)
DHCP Server Function=[Disable]
4. Restart PC.
ꢀꢀ
Specifications
For more information, FAQ’s, and updates, consult the AirStation website at
WHR-G125 AirStation Specifications
Physical Specifications
Dimensions 1.1” x 6” x 6.1” (28 x 152 x 155mm)
Weight .45 lb. (200g)
Temperature & Humidity
Operation 32˚ to 104˚ F, 0˚ to 40˚ C
Maximum humidity 80%
Transit/Storage 0˚ to 40˚ C maximum humidity 80% (no condensation)
Power Characteristics
Power Supply: 100-240V AC Universal, 50/60 Hz.
Power Output: 3.3V DC
Power Consumption about 3 Watts (Max)
ꢀꢁ
Specifications
Regulatory Information
Wireless communication is often subject to local radio regulations. Although AirStation
wireless networking products have been designed for operation in the license-free 2.4 GHz
band, local radio regulations may impose limitations on the use of wireless communication
equipment.
Network Compatability
IEEE802.11g/b Standard for Wireless LANs; 125* High Speed Mode also Available (Turbo G).
Host Operating System
Microsoft Windows® 98SE/ME/NT4.0/2000/XP/Vista, Unix, Linux and MacOS
Media Access Protocol
Wired - CSMD/CD (Collision Detection)
Wireless - CSMD/CA (Collision Avoidance) with Acknowledgment (ACK)
ꢀꢂ
Specifications
AirStation IEEE 802.11 Channel Sets
The range of the wireless signal is related to the Transmit Rate of the wireless
communication. Communications at a lower Transmit range may travel longer distances.
Center Channel ID FCC
1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457
11 2462 11 default channel
ꢀꢃ
Troubleshooting
Common Problems
• Out of range, client cannot connect to the AirStation.
• Configuration mismatch, client cannot connect to the AirStation.
• Absence or conflict with the Client Driver.
• Conflict of another device with the AirStation hardware.
LED Activity
Monitoring LED activity helps identify problems.
• Power LED should be Green.
• Wireless LED should be Green if the line is active. If is it blinking Green, wireless
communication is active.
• Ethernet LED should be Green (100Mbps) or Amber (10Mbps) while communication is
active.
• The Red Diag LED will flash during boot and firmware updates.
DIAG LED Activity
Unplug the power for three seconds. Plug the power back in to monitor the Diag LEDs
during start-up.
ꢀꢄ
Troubleshooting
DIAG LED Activity Table
DIAG LED Display
Time
Description/Action
Continuous Red
Starting
RAM Error Red flash, 2 times Starting Flash
ROM Error
Red flash, 3 times
Red flash, 4 times
Starting
Starting
A problem on the wired LAN side
A problem on the wireless LAN side
LEDs Work But Client PC Cannot Connect to Network
If the LEDs indicate that the network is working properly (Power LED is on, Transmit/
Receive LED blinks), check the TCP/IP settings of the network.
Changing Client TCP/IP Settings in Windows
Consult the LAN Administrator for correct TCP/IP settings.
To add or change TCP/IP Settings:
1. On the Windows task bar, click Start.
2. Select Settings, then Control Panel.
3. Double-click on the Network icon to view Network Properties.
4. From the list of installed components, verify the TCP/IP => wireless LAN adapter
protocol is installed.
ꢀꢅ
Troubleshooting
•
•
If the wireless adapter protocol is not yet installed, click the Add button and select
the TCP/IP protocol from the list. Refer to Windows Help for more information.
If the wireless adapter protocol is installed, select the protocol and click the
Properties button. Verify that the parameters match the settings provided by your
LAN Administrator. Make changes if necessary, and click OK.
5. If prompted, restart your computer.
Other Problems
ꢀꢆ
Glossary
10BaseT: 802.3 based Ethernet network
that uses UTP (Unshielded twisted pair)
cable and a star topology. 10 Mbps data
tansmission speed.
Ad-Hoc Network: A network based on
peer-to-peer communication rather than a
router, switch, or hub.
Bandwidth: The transmission capacity of
a computer or a communication channel,
usually stated in Megabits per second
(Mbps).
100BaseT: 802.3 based Ethernet network
that uses UTP (Unshielded twisted pair)
cable and a star topology. 100 Mbps data
tansmission speed.
Bridge: A device which forwards traffic
between network segments with a common
network layer address, based on data link
1000BaseT: 802.3 based Ethernet
network that uses UTP (Unshielded twisted
pair) cable and a star topology. 1000 Mbps layer information.
data tansmission speed.
Client: A PC, workstation, or other device
802.1x: The standard for wireless LAN
authentication used between an AP and a
client. 802.1x with EAP will initiate key
handling.
that connects to a network wirelessly
through an Access Point.
Cross-Over Cable: A UTP cable that has its
transmit and receive pair crossed to allow
Access Point: A hardware device that acts communications between two devices.
as a communication hub for Clients (users
of wireless devices) to connect to a wired
LAN.
Default Gateway: The IP Address of either
the nearest router or server for the LAN.
ꢀꢇ
Glossary
Destination Address: The address portion
of a packet that identifies the intended
recipient station.
Ethernet: The most widely used
architecture for Local Area Networks
(LANs). It is a shared-media network
architecture. The IEEE 802.3 standard
details its functionality.
DHCP (Dynamic Host Configuration
Protocol): Based on BOOTP, it uses a pool
of IP addresses, which it assigns to each
device connected to it, and retrieves the
address when the device becomes dormant
for a period of time.
Ethernet cable: A wire similar to telephone
cable that carries signals between Ethernet
devices. It is designed to connect a single
device’s NIC to a router, switch, or hub.
See also Crossover cable.
DNS (Domain Name System): System
used to map readable machine names into
IP addresses.
File and Print Sharing: A Microsoft
application that allows computers on a
network to share files and printers.
Driver: Software that interfaces a
computer with a specific hardware device.
Firmware: Computer programming
instructions that are stored in a read-
only memory unit rather than being
implemented through software.
Dynamic IP Address: An IP address that
is automatically assigned to a client station
in a TCP/IP network, typically by a DHCP
server.
Frame: A fixed block of data, transmitted
as a single entity. Also referred to as a
packet.
ꢁ0
Glossary
Full-Duplex: To transmit on the same
ISP (Internet Service Provider): A
channel in both directions simultaneously.
company that provides access to the
Internet and other related services.
Half-duplex: To transmit on the same
channel in both directions, one direction at
a time.
IV (Initialization Vector): The header
section of an encrypted message packet.
Hub: A device which allows connection
of computers and other devices to form a
LAN.
LAN (Local Area Network): A group
of computers and peripheral devices
connected to share resources.
IEEE (Institute of Electrical and
Electronics Engineers): The professional
organization which promotes development
of electronics technology.
LED (Light Emitting Diode): The lights
on a hardware device representing the
activity through the ports.
MAC (Medium Access Control) Address:
IP (Internet Protocol) Address: A unique
The unique number that distinguishes
32-binary-digit number that identifies each every network interface card.
sender or receiver of information sent in
packets.
Mbps (Mega Bits Per Second): A
measurement of millions of bits per
Infrastructure: A wireless network or
other small network in which the wireless
network devices are made a part of the
network through the Access Point.
second.
MDI/X (Media Dependent Interface/
Cross-over): Port on a network hub or
switch that crosses the incoming transmit
lines with the outgoing receive lines.
ꢁ1
Glossary
MHz (MegaHertz): One million cycles per
second.
PCMCIA (Personal Computer Memory Card
International Association) Card: Removable
module that adds features to a portable
computer.
NAT (Network Address Translation): An
internet standard that enables a LAN to
use one set of IP addresses for internal
traffic and a second set for external traffic.
Peer-to-peer: This simple network is formed by
connecting computers directly, without use of
routers or hubs. A crossover cable is plugged
into an Ethernet port in each computer,
connecting them directly.
NIC (Network Interface Card): An
expansion card connected to a computer
so the computer can be connected to a
network.
Ping (Packet Internet Groper): An Internet
utility used to determine whether a particular
IP address is accessable.
Packet: A block of data that is transferred
as a single unit, also called a frame or a
block.
Plug and Play: Hardware that, once physically
installed, finishes its installation automatically
and may immediately be used, as opposed
to hardware that requires further manual
configuration.
Packet Filtering: Discarding unwanted
network traffic based on its originating
address or its type.
PCI (Peripheral Component
Interconnect): A bus that is connected
directly to the CPU.
PoE (Power over Ethernet): A mechanism
to send DC power to a device using a CAT5
Ethernet cable.
ꢁꢀ
Glossary
PPPoE (Point-to-Point Protocol over
Ethernet): A specification for connecting
users on an Ethernet line to the Internet
through a common broadband medium.
ROM (Read Only Memory): Memory
hardware that allows fast access to
permanently stored data but prevents
addition to or modification of the data.
Protocol: A standard way of exchanging
information between computers.
Router: A device in a network that
handles message transfer between
computers. Similar to a hub, but with
added functionality and efficiency.
RADIUS (Remote Authentication Dial
In User Service): A server that issues
authentication keys to clients.
Roaming: The ability to use a wireless
device while moving from one access point
to another without losing the connection.
RAM (Random Access Memory): Non-
permanent memory.
Server: Any computer that makes files or
peripheral devices available to users of the
network and has a resident Network OS.
Repeater Hub: A device that collects,
strengthens and transmits information to
all connected devices, allowing the network
to be extended to accommodate additional
workstations. See also Bridge.
SMTP (Simple Mail Transfer Protocol):
The protocol used to define and deliver
electronic mail (E-mail) from one location
to another.
RC4: The encryption algorithm used by
WEP.
RJ-45 connector: An 8-pin connector
used between a twisted pair cable and a
data transmission device.
ꢁꢁ
Glossary
SNMP (Simple Network Management
Protocol: An application layer protocol
that outlines the formal structure for
communication among network devices.
TKIP (Temporal Key Integrity Protocol):
An encryption method replacing WEP.
TKIP uses random IV and frequent key
exchanges.
Static IP Address: A permanent IP
address is assigned to a node in a TCP/IP
network. Also known as global IP.
Topology: The shape of a LAN (Local Area
Network) or other communications system.
Twisted Pair: Cable that comprises 2
or more pair of insulated wires twisted
together.
SSID: The “name” of your wireless
network. You can get it from the Setup
page of the configuration utility.
UDP (User Datagram Protocol): A
STP (Shielded Twisted Pair): Twisted Pair communication method (protocol)
cable wrapped in a metal sheath to provide
extra protection from external interfering
signals.
that offers a limited amount of service
when messages are exchanged between
computers in a network. UDP is used as
an alternative to TCP/IP.
Subnet Mask: An eight-byte address
divided into 4 parts separated by periods.
Uplink: Link to the next level up in a
communication hierarchy.
TCP/IP (Transmission Control Protocol/
Internet Protocol: Protocol used by
computers when communicating across
the Internet or Intranet.
UTP (Unshielded Twisted Pair) cable:
Two or more unshielded wires twisted
together to form a cable.
ꢁꢂ
Glossary
WAN (Wide Area Network): A networking
WLAN (Wireless LAN): A LAN topology
system covering a wide geographical area.
using wireless devices.
WEP (Wired Equivalent Privacy): A
security protocol for wireless local area
networks defined in the 802.11b standard,
using a 64 bit or 128 bit key. WEP was
designed to provide the same level of
security as that of a wired LAN. However, it
has been found that WEP is not as secure
as once believed.
VPN (Virtual Private Network): A security
method to connect remote LAN users to a
corporate LAN system.
Web Browser: A software program that
allows viewing of web pages.
Wi-Fi (Wireless Fidelity): An organization
that tests and assures interoperability
among WLAN devices.
Wire Speed: The maximum speed at
which a given packet can be transferred
using Ethernet and Fast Ethernet standard
specifications.
ꢁꢃ
FCC / CE Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
ꢁꢄ
FCC / CE Information
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for uncontrolled
equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C
to OET65. This equipment should be installed and operated with at least 20cm and more
between the radiator and person’s body (excluding extremities: hands, wrists, feet and
legs). This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Safety
This equipment is designed with the utmost care for the safety of those who install and
use it. However, special attention must be paid to the dangers of electric shock and static
electricity when working with electrical equipment. All guidelines of this manual and of the
computer manufacturer must therefore be allowed at all times to ensure the safe use of
the equipment.
EU Countries intended for use
The ETSI version of this device is intended for home and office use in Austria, Belgium,
Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece, Iceland,
Ireland, Italy, Luxembourg, Norway, The Netherlands, Portugal, Spain, Sweden, Switzerland
and United Kingdom. The ETSI version of this device is also authorized for use in EFTA
member states Iceland, Liechtenstein, Norway and Switzerland.
EU Countries not intended for use
None.
ꢁꢅ
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
The following test methods have been applied in order to prove presumption of compliance with
the R&TTE Directive 1999/5/EC:
• EN 60950: 2000 Safety of Information Technology Equipment
• EN 300 328-2 V1.2.1 (2001-12) Technical requirements for spread-spectrum radio equipment
• EN 301 489-17 V1.1.1 (2000-09) EMC requirements for spread-spectrum radio equipment
Taiwan:
SAR compliance has been established in typical laptop computer(s) with CardBus
slot, and product could be used in typical laptop computer with CardBus slot. Other
application like handheld PC or similar device has not been verified, may not comply with related
RF exposure rules, and such use shall be prohibited.
Safety
This equipment is designed with the utmost care for the safety of those who install and
use it. However, special attention must be paid to the dangers of electric shock and static
electricity when working with electrical equipment. All guidelines of this manual and of
the computer manufacturer must therefore be allowed at all times to ensure the safe use
of the equipment.
ꢁꢆ
Intended use
This device is a 2.4 GHz & 5 GHz wireless LAN transceiver, intended for indoor home and
office use in USA, Canada, all EU and EFTA member states.
EU Countries intended for use
This device is intended for indoor home and office use in the following countries:
Austria, Belgium, Germany, Denmark, Spain, Greece, France, Finland, Italy, Ireland,
Luxembourg, The Netherlands, Portugal, Sweden, United Kingdom, Cyprus, Czech
Republic, Estonia, Hungry, Latvia, Lithuania, Malta, Poland, Slovak Republic and
Slovenia.
The device is also authorised for use in all EFTA member states Iceland, Liechtenstein,
Norway and Switzerland.
EU countries not intended for use
None
Potential restrictive use
This device is a 2.4 GHz & 5 GHz wireless LAN transceiver, intended for indoor home and
office use in all EU and EFTA member states, except in France, Belgium and Italy where
restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in
order to obtain an authorization to use the device for setting up outdoor radio links.
ꢁꢇ
In Belgium there is a restriction in outdoor use. The frequency range in which outdoor
operation in Belgium is permitted is 2460 – 2483.5 MHz.
In France only channels 10,11,12 and 13 are available.
This device may not be used for setting up outdoor radio links in France. For more
ꢂ0
Environmental Information
• The equipment that you have purchased has required the extraction and use of natural
resources for its production.
• The equipment may contain hazardous substances that could impact health and the
environment.
• In order to avoid the dissemination of those substances in our environment and to diminish the
pressure on the natural resources, we encourage you to use the appropriate take-back systems.
• The take-back systems will reuse or recycle most of the materials of your end life equipment in
a sound way.
• The crossed-out wheeled bin symbol invites you to use those systems.
• If you need more information on the collection, reuse and recycling systems, please contact
your local or regional waste administration.
ꢂ1
Warranty Information
Buffalo Technology (Melco Inc.) products come with a two-year limited warranty from the
date of purchase. Buffalo Technology (Melco Inc.) warrants to the original purchaser the
product; good operating condition for the warranty period. This warranty does not include
non-Buffalo Technology (Melco Inc.) installed components. If the Buffalo product malfunctions
during the warranty period, Buffalo Technology/(Melco Inc.) will, replace the unit, provided
the unit has not been subjected to misuse, abuse, or non-Buffalo Technology/(Melco Inc.)
authorized alteration, modifications or repair.
All expressed and implied warranties for the Buffalo Technology (Melco Inc) product line
including, but not limited to, the warranties of merchantability and fitness of a particular
purpose are limited in duration to the above period.
Under no circumstances shall Buffalo Technology/(Melco Inc.) be liable in any way to the
user for damages, including any lost profits, lost savings or other incidental or consequential
damages arising out of the use of, or inability to use the Buffalo products.
In no event shall Buffalo Technology/(Melco Inc.) liability exceed the price paid for the prod-
uct from direct, indirect, special, incidental, or consequential damages resulting from the
use of the product, its accompanying software, or its documentation. Buffalo Technology
(Melco Inc.) does not offer refunds for any product.
@ 2003-2007 Buffalo Technology (Melco, Inc.)
ꢂꢀ
Contact Information
Buffalo Technology (USA), Inc.
4030 West Braker Lane, Suite 120
Austin, TX 78759-5319
GENERAL INQUIRIES
Monday through Friday
8:30am-5:30pm CST
Direct: 512-794-8533 | Toll-free: 800-456-9799 | Fax: 512-794-8520 | Email:
TECHNICAL SUPPORT
North American Technical Support by phone is available 24 hours a day, 7 days a week.
(USA and Canada).
ꢂꢁ
Contact Information
Buffalo Technology UK Ltd.
176 Buckingham Avenue,
Slough, Berkshire, SL1 4RD
United Kingdom
GENERAL INQUIRIES
Email: [email protected]
TECHNICAL SUPPORT
Phone (UK only): 08712 50 12 60*
Phone: +353 61 70 80 50
Email: [email protected]
*Calls cost 8.5p per minute
Technical Support Operating Hours
Monday - Friday (GMT)
9:00 AM - 6:00 PM Monday-Thursday
9:00 AM - 4:30 PM Friday
ꢂꢂ
GPL Information (North America)
Thank you for your interest in Buffalo products. Our GPL software delivery policy is outlined below.
For each individual product and revision, please send one individually packaged self addressed padded CD
shipping envelope, containing a blank CD-R to the following address:
Buffalo Technology USA Inc.
4030 W. Braker Lane Suite 120
Austin, TX 78759
Attn. GPL Department
Within the envelope containing the self addressed padded CD shipping envelope, please include a bank draft
or money order for $20 (USD) (Made out to: Buffalo Technology) to cover our handling fee, postage and CD
preparation. The CD-R should have the name of the product and revision number clearly written on the
actual CD-R (not on the insert).
We do not send GPL source in bulk on a DVD. And order confirmation is not required by the GNU General
Public License.
We are more than happy to comply with your request; however, we must ask you to comply with our GPL
distribution policy, which complies with the GNU General Public License.
Sincerely,
Buffalo Technology GPL Department
ꢂꢃ
GPL Information (Europe)
Thank you for your interest in Buffalo products. Our GPL software delivery policy is outlined below.
For each individual product and revision, please send one individually packaged self addressed padded CD
shipping envelope, containing a blank CD-R to the following address:
Buffalo Technology Ireland Ltd
Free Zone East, Shannon, Co. Clare
Ireland
Attn. GPL Department
Within the envelope containing the self addressed padded CD shipping envelope, please include a bank draft
or money order for €20 (Euro) (Made out to: Buffalo Technology) to cover our handling fee, postage and CD
preparation. The CD-R should have the name of the product and revision number clearly written on the
actual CD-R (not on the insert).
We do not send GPL source in bulk on a DVD. And order confirmation is not required by the GNU General
Public License.
We are more than happy to comply with your request; however, we must ask you to comply with our GPL
distribution policy, which complies with the GNU General Public License.
Sincerely,
Buffalo Technology GPL Department
ꢂꢄ
125* High Speed Mode
* When operating in High-Speed Mode, this Wi-Fi device achieves an actual
throughput of up to 34.1 Mbps, which is equivalent to the throughput of
a system following 802.11g protocol and operating at a signaling rate of
125 Mbps.
ꢂꢅ
|