BT Digital Baby Monitor 250
User Guide
Got everything?
This User Guide provides you with all the
information you need to get the most
from your BT Digital Baby Monitor 250.
•
•
•
Baby unit
Parent unit
2 x AA NiMH 1300mAh
rechargeable batteries
Please read this guide carefully and
keep it for future reference.
for Parent unit (pre-installed)
•
•
Parent unit charger
2 x power adapters
(item code 057711)
Need help?
If you have any problems setting up or using your
BT Digital Baby Monitor 250 (or would like any
additional or replacement batteries), call our free
BT Digital Baby Monitor Helpline on 0808 100 6554*.
Our dedicated advisors are more likely to be able
to help you than the retailer where you made
your purchase.
•
Travel bag (located
underneath top layer)
Alternatively, you may find the answer in the ‘Help’
section at the back of this guide.
Additional answers to Frequently Asked Questions
* Calls made from within the UK mainland network are free.
Mobile and international call costs may vary.
4
Important safety information
• Your BT Digital Baby Monitor 250 is designed to be an aid and should not be used
as a substitute for responsible and proper adult supervision.
• Make sure the Baby unit, Parent unit and mains adapter cables are kept out of
reach of your baby – at least one metre away.
• Never place the Baby unit inside your baby’s cot, bed or playpen.
• Never cover your Parent or Baby units (e.g. with clothes, towels or blankets).
• Never use or place your Parent or Baby units in moist places or near water.
• If travelling abroad, make sure that the voltage shown on the mains power
adapter corresponds to the local mains power before connecting to the
power supply.
• There is a risk of explosion if the batteries are replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
• Always dispose of batteries in accordance with applicable waste disposal
regulations, never in your household rubbish.
• During continual use the Baby unit and Parent unit power adapters may become
warm to the touch. This is normal and is not something to be concerned about.
• In the event of a power failure, when the power is restored all your settings will
remain unchanged.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
In this guide
5
Important safety information............4 Mute All feature – Parent unit only....20
Mute Low........................................20
Your BT Digital Baby Monitor 250 ...... 7
Talk Back .........................................21
Parent unit ........................................7
Find ................................................22
Parent unit display icons.....................8
Torch...............................................22
Parent unit charger ............................9
The Parent unit menu.......................23
Baby unit ........................................10
Nightlight .......................................24
Back of Baby unit.............................11
Switch nightlight on/off and select
Parent unit menu map......................12
brightness level using the Baby unit..24
Setting up....................................... 13
Switch nightlight on/off using the
Parent unit ......................................24
Select the nightlight brightness level
using the Parent unit........................25
Set the nightlight timer....................25
Play music from the Baby unit ..........25
Parent unit ......................................13
Baby unit ........................................15
Switch on and link the Parent
and Baby units.................................15
Using your BT Digital Baby
Monitor 250 ...................................17
Turn music on/off using the
Baby unit ........................................26
Switch the Baby unit on ...................17
Switch the Parent unit on .................17
Switch the Baby unit off...................17
Switch the Parent unit off.................18
Baby sound level LED indicators .......18
Adjust the loudspeaker volume.........19
Turn music on/off using the
Parent unit ......................................26
Choose a song to play using the
Parent unit ......................................27
Set a play time for music ..................27
Feed Timer ......................................28
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
6
In this guide
Set the feed timer
Help ...............................................36
General information........................ 38
countdown duration ........................28
Start the feed timer countdown........29
Cancel the feed timer countdown .....29
Switch timer repeat option on or off. . 30
Select the type of feed timer alert.....30
Temperature monitor .......................31
Temperature monitor indicators ........31
Select the type of temperature alert. . 32
Temperature alert options ................32
Crying alert .....................................33
Select the type of crying alert...........33
Backlight.........................................34
List of tones ....................................34
Reset the units ................................35
Reset the Parent unit .......................35
Reset the Baby unit..........................35
Cleaning..........................................38
Guarantee .......................................38
Product disposal instructions............39
R&TTE .............................................40
Declaration of Conformance .............40
User Guide formats ..........................40
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Your BT Digital Baby Monitor 250
7
Mute Low
(on top of unit)
Press to toggle the
Mute All
(on top of unit)
Press to toggle the
Parent unit
Power on/off
(on top of unit)
Press and hold to
switch the power
on or off.
Baby unit microphone Parent unit receive
sensitivity between volume between
normal and Mute Low. on and off.
Baby sound level LEDs
Indicates the level of received
sound. The LEDs will light up
progressively as the sound
increases. See page 18 for
further information.
Torch (on back of unit)
Press to switch the torch feature
on and off.
Link indicator
Steady green indicates that the
Baby and Parent units are linked.
Flashes green if no link established
for 30 seconds. Flashes red if no
link established after 30 seconds.
Also flashes green when the Talk
button is pressed on the Parent
unit to initiate parental talk back.
Mute LED
Steady red indicates that Mute
All has been switched on.
Amber indicates that Mute Low
has been switched on.
Talk (on side of unit)
Press to talk to your baby.
Battery status indicator
LCD Display
Power saving backlight turns
on when you press any button
and then switches off after
15 seconds.
Red light indicates the batteries
are low and need re-charging.
Microphone
OK
Press to confirm the menu
option displayed.
Menu
Press to open the menu. Press
and hold to exit the menu and
return to the idle screen.
Down
Decrease speaker
volume. Scroll through
the menu options.
Up
Increase speaker volume.
Scroll through the menu options.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
8
Your BT Digital Baby Monitor 250
Parent unit display icons
Nightlight
Music
Feed Timer
Setup
Menu options:
Battery status
Temperature alert (vibrate on)
Temperature alert (vibrate off)
Nightlight is on
Feed timer on (vibrate on)
Feed timer on (vibrate off)
Full charge (75-100%)
Medium charge (51-74%)
Low charge (25-50%)
Empty (8-24%)
Music is playing
Displays the temperature as
measured at the Baby unit
Flashing (0-7%)
Icon will scroll when charging
Crying alert (vibrate on)
Crying alert (vibrate off)
Indicates when you can scroll up or
down through the menu options
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Your BT Digital Baby Monitor 250
9
Parent unit charger
Front
Charging light
Red when the Parent unit is
correctly placed on the charger.
BT Baby Monitor
Back
Power socket
For connection to the mains
power socket via the power
adapter cable supplied.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
10 Your BT Digital Baby Monitor 250
Temperature sensor
Baby unit
Make sure the sensor is placed
with clear space around it and
not in contact with any surfaces
to ensure it works effectively.
Nightlight
Press to switch the
Nightlight on or off.
Microphone
Brightness
Power on/off
Press and hold to switch the
power on or off.
Press to adjust the nightlight
brightness: high, medium or
low (once the nightlight has
been switched on).
Skip forward
When music has been
switched on (see Music button
description below), press to skip
through the songs available.
Find
Press to emit an alert beep from
the Parent unit – useful for
finding the Parent unit if you’ve
misplaced it.
Music
Press to switch
Volume up/down
music on at the Baby unit
(the music and duration
will be as last set at the
Parent unit). Press again
to switch the music off.
To change the song,
Increase or decrease the
loudspeaker volume for
playing music or for parental
talk back.
Nightlight
Illuminates around the base.
press the Skip button.
Link indicator
Steady green indicates that the Baby and Parent units are linked.
Flashes green if no link established for 30 seconds. Flashes red if no link
established after 30 seconds. Also flashes green when the Talk button is
pressed on the Parent unit to initiate parental talk back.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Your BT Digital Baby Monitor 250 11
Back of Baby unit
Power socket
For connection to the mains
power socket via the power
adapter cable supplied.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
12 Your BT Digital Baby Monitor 250
Parent unit menu map
Turn (On/Off)?
High
Nightlight
Brightness
Timer
Medium
Low
5 min
10 min
15 min
Constant
(Play/Stop)?
Choose Song
Timer
3 Blind Mice
Brahms
Music
5 min
Canon in D
Dream Chase
Dreaming
Hush Baby
Night Night
Twinkle Star
Play All
10 min
15 min
Constant
Menu
(Start/Stop) Timer
Duration
Set Time
Feed Timer
Repeat On
Repeat Off
Repeat
Beep
Beep&Vibe
Vibrate
Alert
Beep
Beep&Vibe
Vibrate
Screen only
Crying Alert
Temp Alert
Backlight
Beep
Setup
Beep&Vibe
Vibrate
Screen only
Off
On w alerts
Off w alerts
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Setting up
13
WARNING!
Parent unit
1. Plug one of the power adapter cables into the
Only use the power adapters
supplied. Using incorrect power
adapters may permanently
damage your product.
socket marked
charger and plug the other end into the mains
power wall socket and switch the power on.
on the back of the Parent unit
Battery performance
Rechargeable batteries
in the Parent unit will last
approximately 20 hours in
normal use. Please note that
new batteries do not reach full
capacity until they have been in
normal use for several days.
The charge capacity of
rechargeable batteries will
reduce with time as they
wear out, so reducing the
performance time of the Parent
unit. Eventually they will need
to be replaced. New batteries
can be obtained from the
BT Digital Baby Monitor 250
Helpline 0808 100 6554*.
2. Activate the batteries by pulling the plastic tab
away from the bottom of the Parent unit.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
14 Setting up
The Parent unit rechargeable
3. Place the Parent unit into the charger. The red
charging light will illuminate on the charger and
the battery icon will start scrolling on the Parent
unit display to indicate that the batteries are
being charged.
batteries will lose charge over
a period of time, even if
switched off.
Battery low warning –
Parent unit
When the batteries are low –
approximately within 1 hour of
running out – the Parent unit
will emit a low battery alert,
the low battery indicator will
turn red, the display will show
Low battery indicator
Battery icon
Low Battery and the
icon
will flash. Place the Parent unit
back on the charger to charge
the batteries. To speed up
the charging process turn the
Parent unit off when charging
if it’s not being used.
You can still use your Parent
unit to monitor your baby
even when the batteries are
low, provided it remains in the
charger cradle to re-charge
the batteries.
Charging light
BT Baby Monitor
Leave the batteries to charge for 16 hours to reach
maximum charge. When the batteries are fully
charged the battery icon on the display will show a
full charge
.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Setting up 15
WARNING
Baby unit
Never use non-rechargeable
batteries in the Parent unit.
Only use the recommended
type – 2 x AA NiMH 1300mAh
batteries. Using other types
could permanently damage the
unit. Charge the batteries as
instructed in this user guide.
The Parent unit can still be used
when it is in the charger.
1. Plug the remaining power adapter cable into the
socket marked
and plug the other end into the mains power and
switch on.
on the back of the Baby unit
Removing the batteries
If you ever need to remove
the batteries, simply slide
open the battery compartment
cover and use the ribbon to
eject the batteries.
Switch on and link the Parent and Baby units
1. Press and hold the
button on the Baby unit for
1 second. The nightlight will briefly illuminate and
then the green Link indicator will flash.
2. Press and hold the
button on the Parent unit
until all the LEDs on the unit briefly illuminate. The
green Link indicator will flash and the display will
show I’m Linking.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
16 Setting up
Positioning your units
Once the units are Linked the green Link light on
the top of the Parent unit and the green LED on
the Baby unit will stop flashing and remain a steady
green. The units are now ready to use.
The Baby unit should ideally be
within 1m-2m of your baby for
best performance.
If you place the Parent and
Baby units too close together
you will hear a high pitched
noise, this is normal. The units
are designed to be located at
a distance from one another,
e.g. in separate rooms.
Important:
The link confirmation between the two units is vital
for use so they can communicate. If the link between
the units is broken at any time, the Link indicators on
both units will flash green as they try to search for
each other. The Parent unit displays I’mLinking...
After 30 seconds, if the link is still broken, the Baby and
Parent units Link indicators will flash red. The Parent
unit display will show NoLink and you will hear an
alert signal.
If the link is broken:
• check that the mains power is plugged in and
switched on at the Baby unit
• check that both units are switched on
• check that the batteries are charged in the
Parent unit
• check that the Parent and Baby units are within
range of each other (in ideal conditions the range
is up to 300 metres outdoors and 50m indoors)
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250
17
Switching on/off
Switch the Baby unit on
1. Press and hold the
button for 1 second. The
nightlight will briefly illuminate and then the green Link
indicator will flash until it links with the Parent unit.
Once linked the green Link indicator will remain on.
Switch the Parent unit on
1. Press and hold the
button on the Parent unit
until all the LEDs briefly illuminate. The green Link
indicator will flash and the display will show I’m
Linking.
Once the units are linked the green Link indicators
on the Parent and Baby units will stop flashing
and remain a steady green. The units are now
ready to use.
Switch the Baby unit off
1. Press and hold the
button on the Baby unit.
The green Link indicator will switch off.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
18 Using your BT Digital Baby Monitor 250
Switch the Parent unit off
1. Press and hold the button on the Parent unit
until an audible alert sounds. The green Link
indicator will switch off and the display will go blank.
Baby sound level LED indicators
LEDs 1-2 = Green
(or Amber if
LEDs 3-4 = Green
LEDs 5-7 = Red
Mute Low is on)
The seven LEDs across the top of the Parent unit
light up to indicate the level of sound being
received from the Baby unit. The LEDs light up
progressively as the sound increases.
LEDs 1-2 light up Green (or Amber if Mute
Low is on, see page 20) when sounds of 57dB and
63dB are received.
Equivalent sound
level examples:
60dB-70dB =
normal conversation
LEDs 3-4 light up Green when sounds of 69dB and
75dB are received.
75dB = loud conversation
83-95dB = loud traffic noise
LEDs 5-7 light up Red when sounds of 83dB, 89dB
or 95dB are received.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 19
If you try and set the volume
higher or lower than the 5
settings available on either unit
you will hear an error tone.
Adjust the loudspeaker volume
At the Parent unit:
1. Press
or
to select the required level.
Setting the Parent unit to
Volume off is the equivalent of
switching the Mute All feature
on. See page 20 for more
information.
The first press will show and sound the current
setting. There are 5 volume levels and off (Mute).
The volume level will be heard and shown on the
display at each press, e.g. Level 3 is shown as
Volume
.
The default loudspeaker volume
on both units is Level 3.
If you wish to switch the volume off, keep pressing
until the display shows Volume Off. The Mute
All indicator will illuminate.
At the Baby unit:
There are 5 volume settings.
1. When Music is being played or Talk back is in
progress from the Parent unit, press the
button to adjust the volume.
or
2. If no music or Talk back is in use, pressing the
or
buttons will adjust the volume and a beep will
sound at the appropriate volume level set.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
20 Using your BT Digital Baby Monitor 250
Be careful not to accidentally
switch the torch feature
on because Mute All is
automatically switched on
when the Torch is switched on.
Mute All feature – Parent unit only
The Mute All feature prevents any sound coming
out from the Parent unit loudspeaker. With Mute All
on you can still monitor your baby using the Baby
sound level LED indicators (page 18) and the Crying
Alert (page 33).
Setting the Parent unit
loudspeaker volume to
Volume off is the equivalent
of switching the Mute All
feature on.
1. To switch Mute All on, press the
button located
on the top of the unit. The Mute indicator will
illuminate red.
2. To switch Mute All off, press the
The red Mute indicator will go off.
button again.
If the
or
buttons are
pressed whilst Mute All or Mute
Low has been set then Mute All
or Low will be switched off and
the loudspeaker volume will
return to Level 3 automatically.
Mute Low
For discreet operation when you do not wish to hear
any low level sounds, you can still monitor your baby
using the Baby sound level LED indicators (page 18).
When Mute Low is switched on, any sounds from
the Baby unit to the Parent unit will be muted
unless a sound is made above a set level. The set
level are sounds that are louder than the first two
green LEDs would register, as described in ‘Baby
sound level LED indicators on page 18.
Once the Mute Low sound
threshold has been exceeded,
baby sounds will be able to be
heard for a further six seconds
even if they do not reach the
Mute Low threshold.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 21
If the Parent unit receives sound up to the level of
the first two LEDs then they will turn amber but no
sound will be heard, if the sound rises above this
level then the unit will un-mute so you can hear the
sounds.
1. To switch Mute Low on, press the
button
Talk Back
located on the top of the Parent unit. The Mute
indicator will turn amber.
You will be able to activate
Talk Back mode even if other
functions have been activated
at the Baby unit like Music
playback or Nightlight on.
2. To switch Mute Low off, press the
The amber indicator will switch off.
button again.
Press or
to adjust the
Talk Back
Talk Back volume level of the
Baby unit loudspeaker.
You can use the Parent unit Talk Back feature as a
one way intercom to comfort and reassure your
baby. By speaking into the Parent unit your baby
will hear your voice from the Baby unit. Please note
that when using Talk Back you will not be able to
Do not press the
button
when the Baby unit and
Parent unit are positioned in
the same room. High-pitch
noise will be generated if the
button is pressed when
Baby unit and Parent unit are
close to each other or within
3 metres distance.
hear your baby until you release the
button.
button on the
1. Press and hold down the
Parent unit to speak to your baby.
When using Talk Back, hold
the Parent unit approximately
30cm in front of your mouth
when talking to baby.
Whilst the
button is depressed the display
will show Talk and the green Link indicators will
flash on both units.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
22 Using your BT Digital Baby Monitor 250
Find
You can press the
button on the Baby unit to
make the Parent unit sound an alert beep to help
you find it if it’s been misplaced. If the Parent unit
loudspeaker volume had been Muted (or set to
volume off), the volume level will be reset to the
default setting of Level 3.
1. Press
on the Baby unit. The paging alert will
sound at the Parent unit and the display will show
Here I am!
2. To stop the alert, press any button on the Parent
unit or press the
button again on the Baby unit.
If no button is pressed after 2 minutes then the
alert will automatically stop.
When the Torch is switched
on it will automatically switch
Mute All on as well. If you then
Torch
The Parent unit has a high intensity white LED torch
that can be used when the Parent unit is switched
on or off.
press the
button Mute will
be disabled and the Torch will
remain on. When the Torch is
switched off, the previous Mute
setting will be restored (No
Mute, Mute All or Mute Low).
1. Press the
button located on the back of the
Parent unit to switch the Torch on and off.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 23
The Parent unit menu
The
button on the Parent unit can be used to
select and change settings on the Baby unit without
having to risk disturbing your baby. You can access
the settings by:
1. Press
the menu options shown on the top of the display.
Press when the option you want is displayed.
then press
or
to scroll through
2. The first sub menu option will be displayed, press
to scroll through the options. The ( arrows)
indicate when you can scroll either up or down.
Press
3. To exit the menu at any time, press
and step back one menu level at a time, or press
and hold to return to the idle screen. If no
when the option you want is displayed.
briefly
buttons are pressed for 10 seconds whilst accessing
the menu, the display will return to idle and any
unsaved changes will be lost.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
24 Using your BT Digital Baby Monitor 250
The Baby unit must be switched
Nightlight
on for the nightlight to work,
but need not be linked to the
Parent unit.
You can set a comforting nightlight on the Baby
unit. There are 3 brightness levels to choose from
and you can set a period of time for the nightlight
to illuminate.
Switch nightlight on/off and select brightness level
using the Baby unit
1. To switch on, press the
2. Press repeatedly to select the brightness level.
3. To switch off, press
button.
.
Switch nightlight on/off using the Parent unit
1. To switch on, press the
displayed, press
button. Nightlight is
.
2. Turn On? is displayed, press
. Light On will
briefly be displayed, then the
icon.
3. To switch off, press
press
. Nightlight is displayed,
. Turn Off? is displayed, press
.
Light Off will briefly be displayed and then the
icon will disappear.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 25
Select the nightlight brightness level using the
Parent unit
1. Press
The default setting is Medium.
. Nightlight is displayed, press
to display Brightness and press
.
2. Press
.
3. Press
or
to display either Low, Medium or
to select. The display will show
High and press
Saved briefly and you’ll hear a confirmation tone.
Set the nightlight timer
1. Press
2. Press
3. Press
. Nightlight is displayed, press
to display Timer and press
or to display either 5 min, 10 min,
to select.
.
The default setting is Constant.
.
15 min or Constant and press
The display will show Saved briefly and you’ll hear
a confirmation tone.
The default music setting is
Play All songs Constantly.
Play music from the Baby unit
The Baby unit has eight songs that can be played to
gently soothe your baby. You can select one song
to play repeatedly or select the Play All option for
a medley of all eight songs. The songs can be set
to play in a loop for 5, 10 or 15 minutes or you can
leave them playing constantly.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
26 Using your BT Digital Baby Monitor 250
Adjust the volume of the music
Turn music on/off using the Baby unit
using the or
the Baby unit.
buttons on
1. To turn the music on, press the
button. The
most recently selected song will start playing at the
time period last selected using the Parent unit.
If music is played at greater
than volume 3, the Crying Alert
may activate if Mute All is used.
2. Press the
button repeatedly to change
the pre-selected song.
3. To turn the music off, press the
button.
Turn music on/off using the Parent unit
1. To turn the music on, press . Nightlight
is displayed, press to display Music and
press
2. Play? is displayed, press
.
. The display will
briefly show Music On, then the name of the song
and the icon and the song will start to play on
the Baby unit.
3. To turn the music off, press
, press
. The display will
. The display will show
to
display Music and press
show Stop?, press
Music Off, the icon will disappear and the
music will stop playing on the Baby unit.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 27
The eight song choices are:
Choose a song to play using the Parent unit
3 Blind Mice, Brahms, Canon
in D, Dream Chase, Dreaming,
Hush Baby, Night Night and
Twinkle Star.
1. Press
. Nightlight is displayed, press
to
display Music and press
.
2. Play? is displayed, press
Choose Song and press
to display
.
3. Use the
and
buttons to scroll through the
when the
Play All will play a medley of
all eight songs.
eight song titles and Play All. Press
option you want is displayed. The display will show
Saved briefly and you’ll hear a confirmation tone.
Set a play time for music
1. Press
. Nightlight is displayed, press
to
display Music and press
2. Play? is displayed, press
displayed and press
until Timer is
.
3. Use the and
options: 5 min, 10 min, 15 min or Constant and
press when the option you want is displayed.
buttons to scroll through the
The display will show Saved briefly and you’ll hear
a confirmation tone.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
28 Using your BT Digital Baby Monitor 250
The timer can be set to
countdown from 1 minute to 99
hours 59 minutes.
Feed Timer
You can set a Feed Timer on the Parent unit to act as
a countdown timer that will alert you when you next
need to feed your baby. You have a choice of alert
types (beep, beep & vibe and vibrate) and you can
set the timer to repeat itself once the alert sounds.
Set the feed timer countdown duration
The feed timer default
countdown duration is set at
02:00 (2 hours).
1. Press
. Nightlight is displayed, press
until Feed Timer is displayed and press
.
2. Start? is displayed, press
Duration and press
to display
.
If the Parent unit is switched
off, the feed timer countdown
will be cancelled and you will
need to start it again when the
unit is switched back on. The
duration, alert type and repeat
settings will still be retained.
3. The display will show 00h:00m (or the currently set
timer). Use the
and
buttons to select the
first digit and press
each digit and press
. Repeat this procedure for
.
The display will show Saved and you’ll hear a
confirmation beep.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 29
Start the feed timer countdown
1. Press . Nightlight is displayed, press
until Feed Timer is displayed and press
2. Start? is displayed, press . The display will
.
briefly show Timer On and then the timer will be
shown counting down the seconds from the time
you set.
When the timer has finished counting down to
00:00 you will hear an alert beep and the timer
digits and
icon will flash. Press any button on
the Parent unit to stop the alert. If you do not stop
the alert it will automatically stop after 2 minutes
(or it will start again if Timer Repeat has been set).
Cancel the feed timer countdown
1. Press
. Nightlight is displayed, press
until Feed Timer is displayed and press
.
2. Stop? is displayed, press
. The display
will briefly show Timer Off, the timer will then
disappear and the display will return to idle.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
30 Using your BT Digital Baby Monitor 250
Switch timer repeat option on or off
1. Press . Nightlight is displayed, press
until Feed Timer is displayed and press
2. Start? is displayed, press until Repeat is
displayed and press
3. Use the and
Repeat On or Repeat Off and press
.
.
buttons to display either
to
select. The display will show Saved and you will
hear a confirmation beep.
The default setting is
Repeat On.
When Repeat On has been set, the feed timer
countdown will start again once the alert has
sounded if it is not switched off.
Select the type of feed timer alert
Feed timer alert options:
Beep = Parent unit will emit an
alert beep only.
1. Press
. Nightlight is displayed, press
until Feed Timer is displayed and press
.
2. Start? is displayed, press
displayed and press
3. Use the and
Beep, Beep&Vibe or Vibrate and press
until Alert is
Beep&Vibe = Parent unit will
emit an alert beep and vibrate.
.
Vibrate = Parent unit will
vibrate only.
buttons to display either
The default setting is
Beep&Vibe.
to select. The display will show Saved and you will
hear a confirmation beep.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 31
IMPORTANT!
The temperature sensor
Temperature monitor
There is a temperature sensor on the Baby unit to
constantly monitor the temperature in your baby’s
room and you’ll be alerted if it gets too hot, too
warm or too cold by the colour of the Baby unit
nightlight changing and the Parent unit will vibrate,
sound an alert beep and display a message on the
screen. The alert type on the Parent unit can be
changed, see page 32. The temperature will be
constantly shown on the Parent unit display in ˚C.
To stop an alert, press any button on the Parent unit.
used in this BT Digital Baby
Monitor 250 is intended as
a guide, to provide parents
with an indication of the room
temperature in which the unit
has been placed.
It is designed to operate within
an approximate tolerance of
+/- 1°C and is not intended to
be as accurate as some medical
devices. Please note that your
own temperature reference e.g.
your central heating thermostat
may not be as accurate, possibly
due to tolerances and positioning
of the thermostat in relation to
the Baby Monitor sensor.
Temperature monitor indicators
Temperature On the Baby unit On the Parent unit
Below 16°C Nightlight
glows Blue
Display shows
Too Cold
Healthcare professionals advise
that the ideal temperature for
your baby’s room is between
16 °C and 20°C.
16 – 20°C
21 – 24°C
Over 24°C
Nightlight
glows Yellow
Nightlight
glows Orange
Nightlight
glows Red
Display shows
Too Warm
Your Parent unit has a built-in
mechanism to prevent repeated
annoying audible alerts if the
room temperature hovers
Display shows
Too Hot
around an alerting threshold.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
32 Using your BT Digital Baby Monitor 250
Pre-set temperature
alert range
Select the type of temperature alert
1. Press
. Nightlight is displayed, press
The Baby unit comes with
pre-set maximum and
until SetUp is displayed and press
.
minimum temperatures,
as stated by the UK
2. Crying Alert is displayed, press
Temp Alert is displayed and press
until
.
Department of Health as part
of the recommendations to
reduce the risk of cot death.
If the temperature falls below or
goes above the setting an alert
will sound on the Parent unit
and the display will show Too
Cold or Too Hot as appropriate.
If it’s too hot, the Baby unit
nightlight will turn red and
if too cold it will turn blue.
The temperature alert pre-set
temperatures are 15°C (and
below) and 25°C (and above).
3. Use the
Beep, Beep&Vibe, Vibrate, Screen Only or
Off and press to select. The display will show
and
buttons to display either
Saved and you will hear a confirmation beep.
To stop an alert, press any button on the Parent unit.
Temperature alert options
Beep = Parent unit will beep. icon will flash.
Beep&Vibe = Parent unit will beep and vibrate.
icon will flash.
Vibrate = Parent unit will vibrate. icon
will flash.
Alerts will be repeated if the
temperature creeps by 2°C into
an alerting range.
Screen Only = icon will flash.
Off = No alerts. icon will not be displayed.
The default setting is
Beep&Vibe.
All of the above alerts will also display the appropriate
message: Too Hot, Too Warm or Too Cold.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 33
Crying alert options
Beep = Parent unit will beep,
Crying Alert will be displayed
and icon will flash.
Crying alert
The crying alert will only be activated if Mute All
has been switched on (or if the Parent unit volume
has been switched to volume off), see page 20 for
information on the Mute All feature.
Beep&Vibe = Parent unit will
beep and vibrate. Crying Alert
will be displayed and
will flash.
icon
With Mute All switched on, if your baby starts to cry
you will not be able to hear the cries, but if the cries
sound above a certain level i.e. if they reach 83dBA,
which is the 1st red Baby sound level LED, then the
Parent unit will activate the crying alert. The default
crying alert type is for the Parent unit to vibrate and
emit an audible beep but you can select a different
alert type if you want to.
Vibrate = Parent unit will
vibrate only (no alert beep will
sound). Crying Alert will be
displayed and the
will flash.
icon
Screen Only = Crying Alert
will be displayed and the
icon will flash.
The default setting is
Beep&Vibe.
Select the type of crying alert
1. Press
until SetUp is displayed and press
2. Crying Alert is displayed, press
3. Use the and buttons to display either
Beep, Beep&Vibe, Vibrate or Screen Only
and press to select. The display will show
. Nightlight is displayed, press
.
The crying alert is a ‘user alert’
as described on page 34.
.
Saved and you will hear a confirmation beep.
To stop an alert, press any button on the Parent unit.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
34 Using your BT Digital Baby Monitor 250
Backlight
You can select whether or not the LCD backlight
comes on when an alert is activated. When the
backlight comes on it will stay on for 15 seconds.
The default setting is On.
1. Press
. Nightlight is displayed, press
until SetUp is displayed and press
.
2. Crying Alert is displayed, press
Backlight is displayed and press
until
.
3. Use the
and
buttons to display either On w
to select.
alerts or Off w alerts and press
The display will show Saved and you will hear a
confirmation beep.
List of tones
Your Baby Monitor unit can produce various tones.
They have the following meaning:
Tone
Meaning
Single tone
Confirmation tone e.g. setting saved.
Double tone (fast) Error tone e.g. max volume reached
when adjusting volume.
Double tone (slow) User alert e.g. crying alert, paging alert etc.
Triple tone (fast)
System alert e.g. link lost, battery low etc.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Using your BT Digital Baby Monitor 250 35
User Alert tones can be silenced by pressing any
button on the Parent unit.
System Alerts can be silenced for a 5 minute period
by pressing any button on the Parent unit.
Resetting the units is
only advisable if you are
Reset the units
experiencing difficulties with
your product. It is a useful
feature that ensures your Baby
Monitor is returned to its new
“out of the box” settings.
Resetting either units will return the settings at that
unit back to its default settings.
Reset the Parent unit
1. Within 3 seconds of the Parent unit being switched
on, press and hold the
button for at least 10
seconds. The display will show Reset for 2
seconds during the reset and then you will
hear a confirmation beep once the reset has
been performed.
Reset the Baby unit
1. Within 3 seconds of the Baby unit being switched
on, press the
button for at least 10 seconds.
You will hear a confirmation beep once
the reset has been performed.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
36
Help
Helpline
• Check units are within range of
one another.
• Check both units are turned on.
If you have any problems using
your BT Digital Baby Monitor 250,
call 0808 100 6554*.
Link indicator is flashing red
• The Link between your units is
broken. You will also hear an alert on
the Parent unit to let you know there
is no communication between the
units. If this happens, check that the
mains power (or batteries) is correctly
connected and that the units are
within range of one another.
Link indicator does not come on
• Check that both the Baby and Parent
units are switched on.
• Check that the batteries in the Parent
unit are correctly installed and that
they are charged.
• Check that the mains power is
plugged in and switched on at the
Baby unit.
• Check that the units are within range
of each other.
See page 15 for instructions on
linking the units.
Battery low on Parent unit
• Put the Parent unit back on the
charger to charge.
Link light is flashing green
• If you have pressed
to use
• Place Parent unit back on the charger
as frequently as possible or ideally
leave it on the charger to ensure the
batteries remain charged.
the Talk Back feature, the Link
light will flash to indicate one-way
communication between the units.
• The units are searching for a
communication link.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Help 37
• To shorten the charging time you
can turn the Parent unit off if it is not
being used while it is charging.
Parent unit remains silent or
very quiet
• You may have set the volume
too low, see page 19 to increase
the volume.
• You may have switched a Mute
feature on, see pages 20-21.
You can hear a high pitched noise
• The units might be too close to
each other.
• The volume setting might be too
high, see page 19.
Talk back feature is not working
• Check that the volume is loud
enough at the Baby unit, see
page 19.
• Check the units are linked, see
page 15.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
38
General information
•
•
This guarantee does not cover the batteries and
any faults or defects caused by accidents, misuse,
fair wear and tear, neglect, tampering with the
equipment, or any attempt at adjustment or repair
other than through approved agents.
Cleaning
Both units have splash resistant grilles and casing.
To clean, wipe with a damp cloth.
This guarantee does not affect your statutory rights.
Guarantee
Your BT Digital Baby Monitor 250 is guaranteed for
a period of 12 months from the date of purchase.
Within the 12 month guarantee period
Prior to returning your product, please read the
Help section beginning on page 36 or contact
the BT Digital Baby Monitor Helpline on 0808
100 6554* for assistance. Additional answers to
Frequently Asked Questions are available from
Subject to the terms listed below, the guarantee
will provide for the repair of, or at BT’s or its agent’s
discretion the option to replace the BT Digital Baby
Monitor 250 or any component thereof, which is
identified as faulty or below standard, or as a result
of inferior workmanship of materials. Products
over 28 days old from the date of purchase may be
replaced with a refurbished or repaired product.
In the unlikely event of a defect occurring, the
Helpdesk will issue a Fault Reference Authorisation
(FRA) number and instructions for replacement or
repair. Please note you will need the FRA number
before returning the product. This does not affect
your statutory rights.
The conditions of this guarantee are:
•
The guarantee shall only apply to defects that occur
within the 12 month guarantee period.
Outside of the 12 month guarantee period:
•
•
Proof of purchase is required.
If your product needs repair after the guarantee
period has ended or if you require technical
assistance outside of the 12 month guarantee
period, please call BT’s approved technical support
agent, Helpdesk Solutions on 0870 240 5029.
The equipment is returned to BT or its agent as
instructed.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
General information 39
Returning your product
Product disposal instructions for residential users
If the Helpline is unable to remedy your problem
they will issue a Fault Reference Authorisation
number and ask you to return the product to your
original place of purchase. Where possible, pack the
product in its original packaging. Please remember
to include all parts, including the power supply
adapters and the original batteries.
When you have no further use for it, please remove
any batteries and dispose of them and the product
as per your local authority’s recycling processes.
For more information please contact your local
authority or the retailer where the product was
purchased.
Product disposal instructions for business users
For guarantee purposes proof of purchase is
required so please keep your receipt.
Business users should contact their suppliers and
check the terms and conditions of the purchase
contract and ensure that this product is not mixed
with other commercial waste for disposal.
Product disposal instructions
The symbol shown here and on the product
means that the product is classed as
Electrical or Electronic Equipment and
should not be disposed with other
household or commercial waste at the
end of its working life.
The Waste of Electrical and Electronic Equipment
(WEEE) Directive (2002/96/EC) has been put in
place to recycle products using best available
recovery and recycling techniques to minimize the
impact on the environment, treat any hazardous
substances and avoid the increasing landfill.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
40 General information
R&TTE
This product is intended for use within the UK.
This equipment complies with the essential
requirements for the Radio Equipment and
Telecommunications Terminal Equipment Directive
1999/5/EC.
Declaration of Conformance
Hereby, CCT declares that this BT Digital Baby
Monitor 250 is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
The Declaration of Conformance for the
BT Digital Baby Monitor 250 is available from
User Guide formats
This document is also available in other formats,
such as Large print, Braille and Audio CD. If you
would like a copy, please call 0808 100 6554*.
If you experience any problems, please call the Helpline on Freephone 0808 100 6554* or visit www.bt.com/producthelp
Offices worldwide
The services described in this publication are subject to availability
and may be modified from time to time. Services and equipment
are provided subject to British Telecommunications plc’s respective
standard conditions of contract. Nothing in this publication forms
any part of any contract.
© British Telecommunications plc 2010.
Registered Office: 81 Newgate Street, London EC1A 7AJ.
Registered in England No. 1800000.
Printed in China.
Designed and produced by The Art & Design Partnership Ltd.
BT Digital Baby Monitor 250 (11/10) Issue 1
|