USER’S GUIDE
V:1041-0208-10
ITP280B
Bar Speaker for iPhone/iPod
Download from Www.Somanuals.com. All Manuals Search And Download.
fcc Warnings
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in ac-
cordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and re-
ceiver.
•
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
additional Warnings
• The apparatus shall not be exposed to dripping or splashing
and that no objects filled with liquids, such as vases, shall be
placed on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel
qu’un vase, ne doit être placé sur l’objet.
• Main plug is used as disconnect device and it should remain
readily operable during intended use. In order to disconnect
the apparatus from the mains completely, the mains plug
should be disconnected form the mains socket outlet com-
pletely.
La prise du secteur ne doit pas être obstruée ou doit être
facilement accessible pendant son utilisation. Pour être com-
plètement déconnecté de l’alimentation d’entrée, la prise
doit être débranchée du secteur.
• Battery shall not be exposed to excessive heat such as sun-
shine, fire or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel
qu’à la lumière du soleil, au feu ou autres choses de sem-
blable.
• Caution marking is located at the rear of the apparatus.
Les marquages sont inscrits en bas de l’appareil.
• The marking information is located at the bottom of appara-
tus.
Les précautions d’emploi sont inscrites en bas de l’appareil.
CUsTOmeR HeLPLINe | 1-314-621-2881
iLive | ITP280B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar sPeaker for iPhone/iPod
features
• Works with iPhone
• Made for iPod
• Video output
• Line input (3.5mm)
• Auxiliary input (RCA)
• Remote control
• 37” length
• FM radio
• Station memory presets (20 FM)
• Last channel memory
• Treble and bass controls
• 3.1 channel stereo system
• Preset EQ
• Subwoofer output
• S-video output
• 2 audio/video inputs
• S-video output
• Basic iPhone/iPod controls
• Supports Universal docking brackets
• Wall mountable
• Digital clock
• SRS TruSurround XT™ with simulated 5.1
effect
• Motorized iPod drawer
• Cloth net speaker grill
• AC power: built-in AC power cable
• Timer
• White LCD display
• Sleep timer
included
• ITP280B
• Remote control (batteries not included)
• Docking brackets for iPhone/iPod (6)
• AC power cable
• FM wire antenna
• Wall-mount hardware
4
iLive | ITP280B
Download from Www.Somanuals.com. All Manuals Search And Download.
taBLe of contents
introduction
6
8
setuP
cLock, aLarM, and sLeeP tiMer
iPhone/iPod and radio
aV1, aV2, auXiLiary inPut, Line inPut, eQ
Basic connectiVity
9
10
11
12
13
14
16
connecting the Bar sPeaker to a tV
Mounting the Bar sPeaker to a WaLL
coMPany inforMation
CUsTOmeR HeLPLINe | 1-314-621-2881
iLive | ITP280B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
introduction
PoWer
Press to turn the bar speaker
off or on.
VoLuMe
Press to adjust the volume.
source
Press to switch between iPod/
iPhone, FM radio, AV1, AV2,
Line, and AUX modes.
PLay/Pause
Press to play or pause a
docked iPhone or iPod.
iPod draWer
Press to open and close the
iPod docking drawer.
Line inPut (3.5mm)
Use to connect an MP3 player
or other audio source to the
bar speaker.
reset
Press using a paperclip or like
object to reset the bar speaker
to it’s original settings.
Video outPut
aV1 inPut
suBWoofer outPut
fM antenna connection
s-Video outPut
aV2 inPut
rca auXiLiary audio
inPuts
6
iLive | ITP280B
Download from Www.Somanuals.com. All Manuals Search And Download.
standBy/on
Press to turn the bar speaker off or
on.
nuMBer keyPad
iPod draWer
Press to open or close the motorized
drawer for iPhone and iPod.
Mute
Press to mute the volume of the bar
speaker.
rePeat
Press to repeat the current track or
entire album.
aLarM
With the power off, press to set and
activate the alarm.
Menu uP/doWn for iPod
Press to navigate the menu on a
docked iPhone or iPod.
cLock
With the power off, press to set the
clock.
treBLe
In EQ mode MUSIC 2.1 or MUSIC 3.1,
press to adjust the levels of treble.
sLeeP
Press repeatedly to set the sleep
timer.
seLect
Press to make a selection on a
docked iPhone or iPod.
Bass
In EQ mode MUSIC 2.1 or MUSIC 3.1,
press to adjust the levels of bass.
shuffLe
Press to play music from a docked
iPhone or iPod in a random order.
reV/fWd for iPod/Min
Press to rewind or fast forward
content from a docked iPhone or
iPod. Press to adjust the minute when
setting the clock or alarm.
eQ
Press to cycle through MUSIC
2.1, MUSIC 3.1, TruSurround XT,
TruSurround XT-DC, and SRS-WOW
equalizer modes.
Menu
Press to access the previous menu on
a docked iPhone or iPod.
PLay/Pause
Press to play or pause a docked
iPhone or iPod.
skiP/tune
Press to skip forwards or backwards
through content on a docked iPhone
or iPod. Press to tune the FM radio.
VoLuMe
Press to adjust the volume.
aLBuM/chaPter/PLayList
Press to cycle through albums,
chapters, and playlists on a docked
iPhone or iPod.
stoP
Press to stop an iPod during play.
MeMory
Press to cycle through FM radio
presets.
source
Press to switch between FM radio,
AV1, AV2, Line, and AUX modes.
iPod
Press to switch to iPod mode.
disPLay
Press to switch between the clock
and current mode display.
MeM
Press to save the current FM radio
station as a preset.
CUsTOmeR HeLPLINe | 1-314-621-2881
iLive | ITP280B
7
Download from Www.Somanuals.com. All Manuals Search And Download.
setuP
Power
Plug the attached AC cord into a standard AC
power outlet to power the bar speaker.
Battery Power
Requires 2 AAA batteries (not included)
8
iLive | ITP280B
Download from Www.Somanuals.com. All Manuals Search And Download.
cLock, aLarM, and sLeeP tiMer
setting the clock
setting the sleep timer
1 With the bar speaker powered on, press the
sLeeP button repeatedly to set the sleep
timer.
1 Press the PoWer button to turn the bar
speaker off.
2 Press the cLock button on the remote.
2 After the set amount of time expires, the bar
speaker will automatically power off.
The clock will begin to blink.
3 Press the reV/fWd for iPod Min/hr
buttons on the remote to adjust the hour
and minute.
4 Press the cLock button to finish setting the
time.
setting the alarm
1 Press the PoWer button to turn the bar
speaker off.
2 Press the aLarM button on the remote.
The alarm time will begin to blink.
3 Press the reV/fWd for iPod Min/hr
buttons on the remote to adjust the hour
and minute.
4 Press the source button to select FM or
iPod mode for the alarm source.
5 Press the aLarM button to finish setting
the alarm time.
6 Once set, the alarm will automatically be
activated. Press the aLarM button an
additional time, after setting the alarm, to
deactivate the alarm.
When the text ALARM appears on the display,
the alarm is activated.
7 After the alarm sounds, press the PoWer
button to turn the alarm off.
CUsTOmeR HeLPLINe | 1-314-621-2881
iLive | ITP280B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
iPhone/iPod and radio
docking an iPhone/iPod
tuning the fM radio
1 Press the PoWer button to turn the bar
speaker on.
1 Press the PoWer button to turn the bar
speaker on.
2 Press the source button to switch to
iPhone/iPod mode. (iPod button on the
remote)
2 Press the source button to switch to FM
radio mode.
3 Press the skiP/tune buttons on the
3 Press the iPod draWer button to open the
remote to tune the FM radio.
MOTORIZED DOCK FOR iPhone/iPod.
saving a station as a Preset
4 Locate the numbered bracket that fits the
iPhone/iPod model that will be docked.
Each included bracket has a number on it,
indicating which iPhone/iPod model that
bracket is compatible with. See the separate
bracket chart page to identify which bracket
is needed.
5 Snap the bracket into place over the
iPhone/iPod connector in the motorized
dock.
1 Follow the instructions for TUNING THE FM
RADIO.
2 Press the MeM button.
3 Press the Menu uP/doWn for iPod
buttons to select a preset. (P01, P02, P03,
etc.)
4 After you’ve selected a preset, press the
MeM button to save the current FM radio
station to the selected preset.
6 Connect the iPhone or iPod to the
connector inside the Dock for iPhone/iPod.
When the speaker is plugged in, using AC
tuning to a Preset fM radio station
power, the docked iPhone or iPod will charge.
1 Follow the instructions for TUNING THE FM
RADIO.
2 Follow the instructions for SAVING A
STATION AS A PRESET.
3 Press the MeMory buttons on the remote
to cycle through preset radio stations.
Playing an iPhone/iPod
1 Follow the instructions for docking an
iPhone/iPod.
2 Press the PLay/Pause button to begin
playing music from the docked iPhone or
iPod.
10
iLive | ITP280B
Download from Www.Somanuals.com. All Manuals Search And Download.
aV1, aV2, auXiLiary inPut, Line inPut, and eQ
Line input
aV1 and aV2
Requires an 3.5mm audio cable (not included)
Requires an RCA audio/video cable (not
included)
1 Connect an RCA audio/video cable to the
aV1 or aV2 inPuts. Connect the other end
of the RCA cable to the audio/video outputs
on a DVD player, stereo system, gaming
system, etc.
1 Connect 3.5mm audio cable to the Line
inPut. Connect the other end of the
3.5mm cable to an MP3 player or other
audio source.
2 Press the PoWer button to turn the bar
speaker on.
2 Press the PoWer button to turn the bar
speaker on.
3 Press the source button to switch to LINE
mode.
3 Press the source button to switch to AV1
or AV2 mode.
4 Use the native controls on the connected
device to begin playing audio or video
routed through the bar speaker.
4 Use the native controls on the connected
device to begin playing audio routed
through the bar speaker.
Built-in sound technologies
Press the eQ button to cycle through the
available equalizer settings.
auxiliary input
Requires an RCA audio cable (not included)
srs trusurround Xt® creates a truly
immersive surround sound experience with
rich bass and clear dialog.
srs trusurround Xt® - dialog clarity Mode
enhances the vocals so dialog is clear and
easy to understand.
1 Connect an RCA audio cable to the
auXiLiary inPuts. Connect the other end
of the RCA cable to the audio outputs on a
DVD player, stereo system, gaming system,
television, etc.
2 Press the PoWer button to turn the bar
speaker on.
3 Press the source button to switch to AUX
mode.
srs WoW® significantly improves the
playback quality of audio, delivering a
dynamic 3D entertainment experience with
deep, rich bass.
Music 2.1 delivers the audio through two of
the three speakers and the subwoofer.
Music 3.1 delivers the audio through all
three of the bar speaker’s speakers and the
subwoofer.
4 Use the native controls on the connected
device to begin playing audio routed
through the bar speaker.
CUsTOmeR HeLPLINe | 1-314-621-2881
iLive | ITP280B
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic connectiVity
Below, you’ll see a basic flow chart of how you can connect your home entertainment devices to
the bar speaker, and in turn how the bar speaker connects to them.
AUDIO
S-VIDEO
VIDEO
AUDIO &/Or
VIDEO
AUDIO &/Or
VIDEO
AUDIO
DVD PLAYER
DIGITAL CABLE or SATELLITE TUNER
GAMING CONSOLE
VCR
SUBWOOFER
12
iLive | ITP280B
Download from Www.Somanuals.com. All Manuals Search And Download.
connecting the Bar sPeaker to a teLeVision
composite Video output
Requires an RCA audio/video cable (not
included.
TELEVISION
VIDEO INPUT
AUDIO OUTPUTS
1 Plug an RCA audio/video cable into the
COMPOSITE VIDEO OUTPUT (yellow)
on the bar speaker and the composite
video input (yellow) on a television.
2 Plug the remaining plugs on the included
RCA audio/video cable into the RCA
AUXILIARY AUDIO INPUTS (red and
white) on the bar speaker and the RCA
stereo audio outputs (red and white) on a
television.
3 Adjust the television’s input setting to
correspond to the inputs used when
connecting the bar speaker.
s-Video output
Requires an RCA audio cable (not
included.
TELEVISION
S-VIDEO INPUT
AUDIO OUTPUTS
Requires an S-video cable (not included)
1 Plug an S-video cable into the S-VIDEO
OUTPUT on the bar speaker and the
S-video input on a television.
2 Plug an RCA audio cable into the RCA
AUXILIARY AUDIO INPUTS (red and
white) on the bar speaker and the RCA
stereo audio outputs (red and white) on a
television.
3 Adjust the television’s input setting to
correspond to the inputs used when
connecting the bar speaker.
CUsTOmeR HeLPLINe | 1-314-621-2881
iLive | ITP280B
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Bar sPeaker to a WaLL
important notes
We recommend having this bar speaker
professionally mounted.
The included spacers should be used at
your discretion to extend the face of the
bar speaker farther from the wall. These
are typically used when mounting the bar
speaker under a television, and the face of the
bar speaker needs to be flush with the face of
the television.
required tools
•
•
•
•
•
Manual or Power Screwdriver
Stud Finder
Pencil
Tape Measure
Level
included hardware
•
•
•
•
•
•
(2) Wall Mount Brackets
(4) Long Screws
(4) Short Screws
(2) 1/4”Spacers
(2) 1/2”Spacers
(2) 3/4”Spacers
14
iLive | ITP280B
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Bar sPeaker to a WaLL
getting started
studs
1 Use the taPe Measure to decide how
high you’d like to hang the bar speaker on
the wall.
The bar speaker must be hung within 6 feet of
an AC power outlet for the attached AC power
cable to reach.
2 Use the stud finder to locate 2 parallel
wooden studs to screw the mounting
brackets into.
screws
spacer
mounting
bracket
16”
3 Mark the wall at the center of the studs
using the PenciL.
4 Line the LeVeL up on both of your marks
to make sure they are level. If they’re not,
adjust the marks as needed to make them
level.
5 After you’ve double checked your markings,
driLL through the top hole on both
mounting brackets directly into the marks
you’ve made on the wall.
ITP280B
6 If you are using the brackets only and no
spacers, use the included short screws.
If you are using any of the spacers or
combination of the spacers, use the long
screws.
ITP280B
7 Use the LeVeL to level each of the hanging
brackets, then drill the second screw
into the bottom hole on both mounting
brackets.
8 Slide the bar speaker onto the mounting
brackets, and make sure there is a firm and
stable connection before letting go of the
bar speaker.
9 Finally, use the LeVeL to confirm that the
bar speaker is level.
CUsTOmeR HeLPLINe | 1-314-621-2881
iLive | ITP280B
15
Download from Www.Somanuals.com. All Manuals Search And Download.
coMPany inforMation
green initiative
environmental Commitment to ‘Protect for Today
and sustain for Tomorrow’
2009 marks the official launch of DPI, Inc.’s corporate
campaign for a greener and cleaner world. DPI and
its four brands, iLive, WeatherX, Capri, and GPX, are
building upon environmental initiatives introduced
at all of their facilities to help formulate and sustain
significant and important conservation efforts within its
manufacturing and marketing communities. In addition
to targeting and selecting energy efficient product
features, and structuring ‘green office’ procedures, other
initial program efforts include:
• Reduction of all packaging sizes
• Recyclable plastics for clamshell packages, with a plan
to eventually replace plastic with recyclable paper
• Recycled fiber board in place of the polyfoam in
packing boxes
• Recycled plastics in place of the virgin material in
product construction
international support
To download this User’s Guide in English, Spanish, or
Para transferir esta guía de usuario en inglés, español, o
Pour télécharger ce guide de l’utilisateur en anglais,
espagnol, ou français, visitez la section de soutien chez
contact information
Address: 2116 Carr Street, St. Louis MO, 63106
Phone: 1-314-621-2881
Fax: 1-314-588-1805
Email: [email protected]
Parts Email: [email protected]
and
are trademarks of SRS Labs, Inc. TruSurround XT and WOW technologies are incorporated
under license from SRS Labs, Inc.
© 2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are
subject to change without notice
Download from Www.Somanuals.com. All Manuals Search And Download.
|