USER’S GUIDE
V:1707-0201-10
ITP180B
Bar Speaker with Dock for iPhone/iPod
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Warnings
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
Additional Warnings
•
The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed
on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux écla-
boussures et aucun objet ne contenant de liquide, tel qu’un vase,
ne doit être placé sur l’objet.
•
Main plug is used as disconnect device and it should remain
readily operable during intended use. In order to disconnect the
apparatus from the mains completely, the mains plug should be
disconnected form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facile-
ment accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débran-
chée du secteur.
•
Battery shall not be exposed to excessive heat such as sunshine,
fire or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à
la lumière du soleil, au feu ou autres choses de semblable.
•
•
Caution marking is located at the bottom of the apparatus.
Les marquages sont inscrits en bas de l’appareil.
The marking information is located at the bottom of apparatus.
Les précautions d’emploi sont inscrites en bas de l’appareil.
CUSTOMER HELPLINE | 1-314-621-2881
iLive | ITP180B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BAR SPEAKER WITH DOCK FOR IPHONE/IPOD
Features
• Works with iPhone
• Made for iPod
• Video output
• Audio/video input
• 30” length
• Line input (3.5mm)
• FM radio
• Remote control
• Station memory presets (20 FM)
• Last channel memory
• Treble and bass controls
• 2.1 channel stereo system
• Preset EQ
• Subwoofer output
• Last user setting memory
• 2 auxiliary audio inputs (RCA)
• S-video output
• Basic iPhone/iPod controls
• Supports Universal docking brackets
• Wall mountable
• Digital clock
• Single alarm
• Gradual wake
• Motorized iPod drawer
• Cloth net speaker grill
• AC power: built-in AC power cable
• Wake to iPhone/iPod or radio
• White LCD display
• Sleep timer
Included
• ITP180B
• Remote control: requires 2 AAA
batteries (not included)
• Docking brackets for iPhone/iPod (6)
• FM wire antenna
• Audio/video cable
• Wall-mount hardware
4
iLive | ITP180B
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
INTRODUCTION
6
8
SETUP
CLOCK, ALARM, AND SLEEP TIMER
IPHONE/IPOD AND FM RADIO
9
10
11
12
13
14
16
AUXILIARY INPUT, LINE INPUT AND
SUBWOOFER OUTPUT
BASIC CONNECTIVITY
AV INPUT AND VIDEO INPUT
MOUNTING TO A WALL
COMPANY INFORMATION
CUSTOMER HELPLINE | 1-314-621-2881
iLive | ITP180B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
POWER
Press to turn the
bar speaker off
or on.
POWER
SOURCE
Press to switch
between iPhone/
iPod, AV, AUX, and
FM modes.
SOURCE
S
LINE IN
LINE INPUT
(3.5mm)
VOLUME
VOLUME
Press to adjust the
volume.
PLAY/PAUSE
iPod DRAWER
PLAY/PAUSE
Press to play or
pause a docked
iPhone or iPod.
iPod DRAWER
Press to open or
close the motor-
ized dock for
iPhone/iPod.
MOTORIZED
DOCK FOR IPOD
VIDEO INPUT
AUXILIARY INPUT
RESET
Press using a
SUBWOOFER
OUTPUT
paperclip or like
object to reset the
bar speaker to it’s
default settings.
FM ANTENNA
CONNECTION
S-VIDEO OUTPUT
VIDEO OUTPUT
A/V INPUT
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDBY/ON
Press to turn the bar
speaker off or on.
iPod DRAWER
Press to open or
close the motorized
dock for iPhone/iPod.
MUTE
Press to mute the
volume.
NUMBER KEYPAD
REPEAT
ALARM
With the power
off, press to set the
alarm.
Press to repeat a
single track or entire
album on a docked
iPhone or iPod.
CLOCK
With the power off,
press to set the clock.
TREBLE
With the EQ set to
FLAT, press to adjust
the levels of treble.
SLEEP
Press repeatedly to
set the sleep timer.
MENU UP/DN
Press to navigate up
and down in menus
on a docked iPhone
or iPod.
BASS
With the EQ set to
FLAT, press to adjust
the levels of bass.
SELECT
Press to make
selections on a
docked iPhone or
iPod.
REV/FWD/MIN/HR
Press to rewind or
fast forward a docked
iPhone or iPod. Press
to adjust the hour
and minute when
setting the clock or
alarm.
SHUFFLE
Press to play songs
from a docked
iPhone or iPod in a
random order.
MENU
Press skip through
menus on a docked
iPhone or iPod.
EQ
Press to adjust the
EQ.
TUN/SKIP
Press to skip between
tracks on a docked
iPhone or iPod. Press
to tune the radio.
VOLUME
Press to adjust the
volume.
PLAY/PAUSE
Press to play or pause
a docked iPhone or
iPod.
ALBUM/CHAPTER/
PLAYLIST
Press to skip through
albums, chapters, or
playlists on a docked
iPhone or iPod.
STOP
Press to stop a
docked iPhone or
iPod during play.
SOURCE
Press to switch
between AV, AUX,
FM, and iPhone/iPod
modes.
MEMORY
Press to cycle
through saved radio
stations.
iPod
DISPLAY
Press to view the
clock on the display.
iPod
Press to switch to
iPhone/iPod mode.
MEM
Press to save a radio
station to the bar
speaker’s memory.
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Power
Plug the attached AC cord into a
standard AC power outlet to power the
bar speaker.
Remote
Requires 2 AAA batteries (not included)
FM Antenna
Plug the FM Wire Antenna (included)
into the FM Antenna Connection.
8
iLive | ITP180B
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOCK, ALARM, AND SLEEP TIMER
Setting the Clock
Setting the Alarm
1 Press the POWER button to turn the
power on.
1 Press the POWER button to turn the
power off.
2 Adjust the volume to the desired
level.
2 Press the CLOCK button on the
remote control.
3 Press the POWER button to turn the
power off.
The time on the display will begin
blinking.
4 Press the ALARM button on the
remote control.
3 Press the REV/MIN and FWD/HR
buttons on the remote to adjust the
minute and hour.
The alarm time on the display will
begin blinking.
4 Wait 5 seconds to finish setting the
clock.
5 Press the REV/MIN and FWD/HR
buttons on the remote to adjust the
minute and hour.
Setting the Sleep Timer
6 Press the SOURCE button on the
bar speaker to switch to the desired
alarm source.
1 Press the POWER button to turn the
power on.
2 Press the SOURCE button on the
bar speaker to switch to the desired
sleep timer source.
7 Wait 5 seconds to finish setting the
alarm.
ALARM will appear on the display
when the alarm is set.
3 Press the SLEEP button repeatedly to
set the sleep timer.
8 Press the ALARM button to cancel
the alarm.
4 After the set sleep time has expired,
the bar speaker will automatically
power off.
CUSTOMER HELPLINE | 1-314-621-2881
iLive | ITP180B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IPHONE/IPOD AND FM RADIO
Docking an iPhone/iPod
Tuning the FM Radio
1 Press the POWER button to turn the
bar speaker on.
1 Press the POWER button to turn the
bar speaker on.
2 Press the SOURCE button to switch
to iPhone/iPod mode.
2 Press the SOURCE button to switch
to FM radio mode.
3 Press the iPod DRAWER button to
open the MOTORIZED DOCK FOR
iPhone/iPod
4 Locate the numbered bracket that
fits the iPhone/iPod model that will
be docked.
3 Press the TUN/SKIP buttons on the
remote to tune the FM radio.
Saving a Radio Station
1 Follow the instructions for tuning the
FM radio.
Each included bracket has a number
on it, indicating which iPhone/iPod
model that bracket is compatible with.
See the separate bracket chart page to
identify which bracket is needed.
2 After tuning to the desired station,
press the MEM button.
3 Press the MENU UP or MENU DN
buttons on the remote to select a
preset.
5 Snap the bracket into place over
the iPhone/iPod connector in the
motorized dock.
4 Press the MEM button to save the
current radio station to the selected
preset.
6 Connect the iPhone or iPod to
the connector inside the Dock for
iPhone/iPod.
Up to 20 stations can be saved to the
bar speaker’s memory.
When the speaker is plugged in, using
AC power, the docked iPhone or iPod
will charge.
Listening to Saved Radio Stations
1 Press the POWER button to turn the
bar speaker on.
Playing an iPhone/iPod
2 Press the SOURCE button to switch
to FM radio mode.
1 Follow the instructions for docking
an iPhone/iPod.
3 Press the MEMORY buttons on the
remote to cycle through saved radio
stations.
2 Press the PLAY/PAUSE button to
begin playing music from the docked
iPhone or iPod.
10 iLive | ITP180B
Download from Www.Somanuals.com. All Manuals Search And Download.
AUXILIARY INPUT, LINE INPUT, AND SUBWOOFER OUTPUT
Using the Subwoofer Output
Using the Auxiliary Input
1 Use an RCA cable (included) to
connect an external subwoofer to
the SUBWOOFER OUTPUT.
1 Connect an RCA cable (included) to
the AUXILIARY INPUTS on the bar
speaker and an audio source.
2 When audio is played through
any source, the bar speaker will
automatically use the connected
subwoofer.
2 Press the POWER button to turn the
bar speaker on.
3 Press the SOURCE button to switch
to AUX mode.
The AUXILIARY INPUTS will not work
when the LINE INPUT is connected.
4 Use the native controls on the
connected audio device to
begin playing music through the
connected bar speaker.
Using the Line Input
1 Connect a 3.5mm line input cable
(not included) to the LINE INPUT on
the bar speaker and an audio source.
2 Press the POWER button to turn the
bar speaker on.
3 Press the SOURCE button to switch
to AUX mode.
When the LINE INPUT is connected, the
AUXILIARY INPUTS will not work.
4 Use the native controls on the
connected audio device to
begin playing music through the
connected bar speaker.
CUSTOMER HELPLINE | 1-314-621-2881
iLive | ITP180B 11
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC CONNECTIVITY
Below, you’ll see a basic flow chart of how you can connect your home
entertainment devices to the bar speaker, and in turn how the bar speaker connects
to them.
AUDIO
S-VIDEO
VIDEO
AUDIO &/Or
VIDEO
AUDIO &/Or
VIDEO
AUDIO
DVD PLAYER
DIGITAL CABLE or SATELLITE TUNER
GAMING CONSOLE
VCR
SUBWOOFER
12 iLive | ITP180B
Download from Www.Somanuals.com. All Manuals Search And Download.
AV INPUT AND VIDEO INPUT
Using the Video Output
Using the AV Input
1 Connect an RCA cable (included) to
the AV INPUTS and an audio source.
1 Connect an RCA cable (included) to
the VIDEO OUTPUT and a television.
2 Press the POWER button to turn the
bar speaker on.
2 Adjust the connected television to
the proper input setting.
3 Press the SOURCE button to switch
to AV mode.
3 Video from a docked iPhone/iPod, or
a connected DVD player can now be
played through the bar speaker to
the connected television.
4 Use the native controls on the
connected audio device to
begin playing music through the
connected bar speaker.
Using the S-Video Output
The S-Video Output will only output
video from a docked iPod/iPhone.
Using the Video Input
1 Connect an RCA cable (included) to
the VIDEO INPUT and a video source
(DVD player, Cable or Satellite Tuner,
Gaming Console, or VCR).
1 Connect an S-Video cable (not
included) to the S-VIDEO OUTPUT
and a television.
2 Adjust the connected television to
the proper input setting.
2 Connect the bar speaker to a
television using the VIDEO OUTPUT
or S-VIDEO OUTPUT.
3 Video from a docked iPhone/iPod
can now be played through the bar
speaker to the connected television.
3 Press the POWER button to turn the
bar speaker on.
4 Press the SOURCE button to switch
to AV mode.
5 Use the native controls on the
connected video device to control
video that runs through the bar
speaker.
CUSTOMER HELPLINE | 1-314-621-2881
iLive | ITP180B 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTING TO A WALL
Important Notes
We recommend having this bar speaker
professionally mounted.
The included spacers should be used
at your discretion to extend the face
of the bar speaker farther from the
wall. These are typically used when
mounting the bar speaker under a
television, and the face of the bar
speaker needs to be flush with the face
of the television.
Required Tools
•
•
•
•
•
Manual or Power Screwdriver
Stud Finder
Pencil
Tape Measure
Level
Included Hardware
•
•
•
•
•
•
(2) Wall Mount Brackets
(4) Long Screws
(4) Short Screws
(2) 1/4”Spacers
(2) 1/2”Spacers
(2) 3/4”Spacers
14 iLive | ITP180B
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
studs
1 Use the Tape Measure to decide
how high you’d like to hang the bar
speaker on the wall.
screws
spacer
The bar speaker must be hung within
6 feet of an AC power outlet for the
attached AC power cable to reach.
mounting
bracket
2 Use the Stud Finder to locate 2
parallel wooden studs to screw the
mounting brackets into.
16”
3 Mark the wall at the center of the
studs using the pencil.
4 Line the level up on both of your
marks to make sure they are level.
If they’re not, adjust the marks as
needed to make them level.
ITP180B
5 After you’ve double checked your
markings, drill through the top hole
on both mounting brackets directly
into the marks you’ve made on the
wall.
ITP180B
6 If you are using the brackets only
and no spacers, use the included
short screws. If you are using any of
the spacers or combination of the
spacers, use the long screws.
7 Use the Level to level each of the
hanging brackets, then drill the
second screw into the bottom hole
on both mounting brackets.
8 Slide the bar speaker onto the
mounting brackets, and make sure
there is a firm and stable connection
before letting go of the bar speaker.
9 Finally, use the Level to confirm that
the bar speaker is level.
CUSTOMER HELPLINE | 1-314-621-2881
iLive | ITP180B 15
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPANY INFORMATION
International Support
To download this User’s Guide in English,
Spanish, or French, visit the support section at
Para transferir esta guía de usuario en inglés,
español, o francés, visite la sección de la ayuda en
Pour télécharger ce guide de l’utilisateur en
anglais, espagnol, ou français, visitez la section de
Contact Information
Address: 2116 Carr Street, St. Louis MO, 63106
Phone: 1-314-621-2881
Fax: 1-314-588-1805
Email: [email protected]
Parts Email: [email protected]
© 2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are
subject to change without notice
Download from Www.Somanuals.com. All Manuals Search And Download.
|