Model iDN48
Dual Charging Portable
Rechargeable
Speaker System
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
•
•
Place the unit on a level surface away from sources of direct sunlight or excessive heat.
Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material
should be placed between it and the furniture.
•
Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzene,
thinner or similar materials can damage the surface of the unit.
Internal Rechargeable Lithium-ion Battery
This device uses an internal rechargeable lithium-ion battery that should last the lifetime of the device. If you suspect
your battery may be dead, try charging it several times. If the battery does not recharge, please contact us for repair
information.
WARNING/DISPOSAL OF UNIT
Please do NOT attempt to change the battery yourself. If the battery has died and you do not want us to replace your
battery, you should follow the disposal instructions below:
• Never dispose of used batteries/electronics with ordinary solid wastes, since they contain toxic substances.
• Always dispose of used batteries/electronics in accordance with the prevailing community regulations that apply to
the disposal of batteries/electronics. If there are no local regulations concerning battery/electronics disposal, please
dispose of the device in a waste bin for electronic devices.
• Many electronics retailers now recycle batteries and other electronic components at no charge. Check to see which
ones in your area do so.
CAUTION
• Never use or charge the battery if it appears to be leaking, discolored, deformed, or in any way abnormal.
• Never disassemble the unit or attempt to remove battery as that could cause leakage of alkaline solution or other
electrolytic substance.
• Always confirm that the temperature is 5°C – 35° C (41° - 95° Fahrenheit) before you charge the battery. Leakage or
deterioration of the battery may occur if this warning is not heeded.
• Never expose the battery to any liquid.
• Never expose the battery to excessive heat such as direct sunlight or fire. Never use the battery pack in an
unventilated vehicle where excessive internal temperatures may be encountered.
• Always keep the battery out of the reach of infants and small children.
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Indicators
Top Panel
Flexible 30 pin connector
for iPad/iPhone/iPod
Power/Mode
Indicator light
Rubberized backrest
Power/Mode Charge Indicator
Button
Lower Volume Button
Raise Volume Button
USB Charging and Playing Port
Back Panel
Bottom Panel
Aux-in Jack
DC Adapter Jack
DC 12V 3.5A
Reset Port
1
Download from Www.Somanuals.com. All Manuals Search And Download.
quick start
1: stand
2: power
Back rest
OPEN
Stand
CLOSE
Gently pull backwards on the indent of the stand located
on the rear of the unit and pull it into place for support mode.
The retractable backrest will pop up to support a docked
device. To close the stand, simply press back into place.
Attach AC adaptor cable to DC jack on bottom of the unit
and plug the other end into a wall socket. A row of 4 blue
LED indicators will light up indicating the unit has power and
has begun charging the internal battery.
DO NOT dock an iPad, iPhone or iPod without first
opening the stand and popping up the backrest,
doing so could damage the unit and/or your device.
3: docking your
iPad/iPhone/iPod
in the 30-pin
connector dock
4: connecting devices to the USB port
Gently dock your 30-pin compatible iPad, iPhone or iPod onto
the 30-pin dock on top of the unit. The iPad, iPhone or iPod
will charge while docked. Use the controls on your device to
play your iPad, iPhone or iPod. The 30-pin dock is NOT
compatible with iPhone 5 and other Lightning compatible
devices. To play these devices, connect them to the USB port
using the cable that came with the device. Note that USB port
will not charge iPad models.
To play and charge Lightning and other iOS devices, connect
them to the USB port on back of the unit using the cable
that came with the device. Use the controls on your device
to navigate and play your iPad, iPhone or iPod. The USB
port will not charge iPad models.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Unit
Connecting the Unit to Power Source
Connect the AC adaptor cable plug into the DC jack on the back of the system, then plug the AC adaptor into the wall
outlet.
Charging the Internal Battery
The iDN48 has an internal rechargeable Lithium-ion battery which should last the life of the unit. Charge the battery fully
for first time use. Please allow at least 6 hours to fully charge the unit for first time use.
1. Make sure the AC adaptor is properly connected to the unit and plugged into a working power source.
2. The internal battery will charge. While the battery is charging, the blue LED battery indicator lights will cycle to the right.
3. When the battery is fully charged, all 4 battery indicators will remain lit while the unit is powered on. As the battery runs
down, the lights will go out (see below).
Fully charged
75-50% charge 50-25% charge
25-5% charge
When there is no battery indicator light, the battery is dead and needs to be charged. NOTE: Even if the battery is dead,
the unit will still operate while connected to AC power.
NOTE: iHome+Apps will not work when unit is operating on battery power.
Charging your iPad, iPhone or iPod
1. The unit must be connected to an AC power source to charge your iPad, iPhone or iPod, whether docked in the 30-pin
connector or connected to the USB port on the back of the unit. The unit will not charge these devices when
operating on the internal battery.
2. Open the stand and gently dock your iPad, iPhone or iPod. Note that iPhone 5, iPad mini, iPad (4th generation) and
iPod touch 5th generation cannot dock to the unit, but must be connected to the USB port using the sync cable that
came with it. The USB port will NOT charge iPad models.
Your device will begin charging and while docked or connected via USB will continue until fully charged.
Turning the Unit ON or OFF and Selecting Modes
Press and release the
the three play modes.
Power/Mode Button on the unit at any time as needed to turn the unit ON and to cycle through
A. 30-pin dock mode: the Power/Mode indicator light is BLUE and the device docked in the 30-pin dock will play.
B. USB mode: the Power/Mode indicator light is GREEN and the device connected to the USB port will play.
C. Aux-in mode: the Power/Mode indicator light is RED and the aux-in mode is activated (press play on the device to
play it).
Note that a docked iPad, iPhone or iPod (or one connected to the USB port) will continue to charge when the unit is turned
off as long as the AC adaptor is plugged in.
Press and hold the Power/Mode Button to turn the unit off.
TIP: You can also turn the unit ON automatically by docking a playing device or connecting one to the USB port, and turn
the unit OFF by disconnecting a playing device from the dock OR USB port.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Unit
Playing Devices Using the 30-pin Dock
Lightning devices such as iPhone 5, iPad mini, iPad (4th generation), 5th generation iPod touch and 7th generation iPod nano
will NOT dock in the 30-pin dock. Use the USB port to charge and play these iPhone and iPod models and to play iPad mini
and iPad (4th generation).
1. Dock an already playing 30-pin compatible iPad, iPhone or iPod. The unit will turn on and the audio will play from your
device. You can also turn on the unit by pressing and releasing the Power/Mode Button until the Power/Mode indicator
glows BLUE.
2. Use the controls on your iPad, iPhone or iPod to pause and play audio and to navigate tracks and menus.
3. Press the or
4. Press and hold the
Button to adjust the volume level on the unit.
Power/Mode Button to turn the unit off.
Playing Devices Using the USB Port
1. Connect an already playing iPad, iPhone or iPod to the USB port on the back of the unit using the cable that came with the
device. The unit will turn on and the audio will play from your device. You can also turn on the unit by pressing and releasing
the
Power/Mode Button until the Power/Mode indicator glows GREEN.
2. Use the controls on your iPad, iPhone or iPod to pause and play audio and to navigate tracks and menus.
3. Press the or
4. Press and hold the
Button to adjust the volume level on the unit.
Power/Mode Button to turn the unit off.
Playing Devices Using the Aux-in Jack
1. Connect a 3.5mm audio cable to the headphone jack or aux-out jack on your audio device and connect the other end to
the aux-in jack located on the bottom of the unit.
2. Press and release the
Power/Mode Button until the Power/Mode indicator glows RED.
2. Use the controls on your device to pause and play audio and to navigate tracks and menus.
3. Press the or
Button to adjust the volume level on the unit.
4. Press and hold the
Power/Mode Button to turn the unit off. Remember to turn off your aux device, too.
Resetting the unit
If the unit does not respond properly or appears to be “frozen”, you may wish to try resetting it. To do so, press point of a pin
or paperclip firmly into the Reset Port on the bottom of the unit to reset the unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
A Consumer Guide to Product Safety
IMPORTANT SAFETY INSTRUCTIONS
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions
carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings
listed in these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation.
For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also,
it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through
the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to
where it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning
instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any
openings or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent
damage to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A.
B.
the power supply cable or plug has been damaged.
objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E.
the unit exhibits a marked change in performance or does not operate normally.
12. Antenna – Do not connect an external antenna to the unit (other than that provided).
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the
power cable should be unplugged from the unit to prevent damage or corrosion.
14. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.
or call 1-877-446-6301 Toll Free
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Possible Problem
Solution
Unit does not turn on
AC adaptor isn't plugged into a working wall
socket or not plugged into the DC jack on back
of the unit
Plug the AC adaptor into a working wall socket and plug the connector
into the DC jack on the unit
Internal battery is run down/ needs charging
If the Internal battery is run down/ needs charging, connect unit to AC
outlet to recharge battery
Unit doesn’t respond
Unit requires a reset
If unit is plugged in and doesn't respond, try resetting the unit by
inserting the end of a paper clip or similar into the Reset Port located
on the back of the unit and holding briefly.
iPad/iPhone/iPod is not docked or connected
properly
Remove your device from the dock OR USB port and check for obstruction
in the dock or USB port and on your device. Replace in dock OR USB
port. Check that USB cables are connected.
iPad/iPhone/iPod does iPad/iPhone/iPod is not docked or connected
Remove your device from the dock OR USB port and check for obstruction
in the dock or USB port and on your device. Replace in dock OR USB
port. Check that USB cables are connected.
not respond to the
unit, iPad/iPhone/iPod
is playing but no
properly
sound comes out
Your iPad/iPhone/iPod software is too old
Upgrade software on your iPad/iPhone/iPod via iTunes on your
computer
Check the volume setting. Make sure your iPad/iPhone/iPod is working
properly before docking into the unit. Please refer to your iPad/iPhone/iPod
manual for details. See above for software upgrade information.
You may need to reset your iPad/iPhone/iPod. Refer to your iPad, iPhone
or iPod user guide for details on how to perform a reset.
iPad/iPhone/iPod is locked up/plays but no
sound comes out
Unit/iPad/iPhone/iPod
performance is erratic
The unit is reacting to external interference
Volume is set too low on unit
Move unit away from potential sources of external interference such as
computers, modems, wireless devices (routers) or fluorescent light.
No sound from unit
Make sure volume is turned up
Remove your device from the dock OR USB port and check for obstruction
in the dock or USB port and on your device. Replace in dock OR USB
port. Check that USB cables are connected.
iPad/iPhone/iPod is not docked or connected
properly
iPad/iPhone/iPod
didn’t charge up
iPad is connected to USB port
The USB port does not support iPad charging. Charge your iPad in the
30-pin dock, or for models with 8-pin Lightning connector, connect to
power source using cables that came with the device.
iPad/iPhone/iPod is locked up/ frozen
Please make sure your iPad/iPhone/iPod is working properly before
docking into the unit. Please refer to your iPad/iPhone/iPod manual for
details.
iPad/iPhone/iPod battery has problem
Unit is operating on internal battery
Make sure unit is connected to AC power to charge connected
devices. Unit will not charge devices while operating on the internal
battery.
iHome App alarm
did not go off
Selected alarm connection (USB or 30-pin
dock was not the last connection the device
was PLAYED through
In order to respond to a wakeup command, the target device must be
in the last connection (USB or 30-pin dock) a device was playing in,
not just docked to.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Limited 1 Year Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product to be free from defects in
workmanship and materials, under normal use and conditions, for a period of one (1) year from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should
this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI will repair
or, at its discretion, replace this product without charge. This decision is subject to verification of the defect or malfunction upon delivery
of this product to the Factory Service Center authorized by SDI Customer Service. The product must include proof of purchase, including
date of purchase. An out-of-warranty fee for service will be charged for units that are received without proof of purchase.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries
are the most common cause of problems encountered.
If service is still required:
1. Call SDI Customer Service at 1-877-446-6301 for Return Authorization and for the address of the Factory Service Center.
2. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box. SDI is not responsible for damage that
occurs during shipping to the Factory Service Center.
3. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.
Also include your name and address information, a brief description for why the unit is being returned, and the return authorization number.
No unit can be processed without a return authorization number.
4. Write the return authorization number on the side of the shipping package and send the unit prepaid and insured to the Factory Service
Center address authorized by SDI Customer Service.
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser.
In no event will SDI or any of its affiliates, contractors, resellers, their officers, directors,
shareholders, members or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual,
exemplary or punitive damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so
these restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI product.
© 2013 SDI Technologies, Inc. All rights reserved
or call 1-877-446-6301 Toll Free
iDN48-120612-A
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|