Model iH12
Dual Alarm Cube Clock
Radio For Your iPod
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1
2
3
3
4
Quick Start
Controls and Indicators
iH12 Display
Install Clock Backup Battery
Using The Remote Control Unit
Install/Replace the Remote Control Battery
To check for iPod compatibility
5
Setting Up the iH12
Setting Time and Calendar
6
6
Using the Alarm
Charging you iPod
Listening to iPod
7
7
Listening to non-docking iPod or other portable audio devices
Dimme Operation
7
8
Listening to Radio
8
Sleep Operation
8
Click Sound Operation
8
3D Sound Operation
9
A Consumer Guide to Product Safety
Trouble Shooting
10
11
12
Solución De Problemas
Warranty Information
Maintenance
• Place the unit on a level surface away from sources of direct sunlight or excessive heat.
• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material
should be placed between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner
or similar materials can damage the surface of the unit.
FCC Information
This device complies with part 15 of the Federal Communications Commission Rules. Operation is subject to the condition
Download from Www.Somanuals.com. All Manuals Search And Download.
that this device does not cause.
Quick Start
3:iPod
1:power
2:inserts
Select the dock insert for your
iPod model from the table below
and place insert in dock.
Never dock an iPod without
an insert in place.
Insert iPod into dock with proper
insert (iPod must not be in a skin or
case). iPod will charge while docked.
Press the Play Button on the iH12 to play
iPod.
Attach AC adaptor cable to jack on
back of the iH12 and plug the other
end into a wall socket.
iPod Touch
insert 14
3rd Gen nano
insert 13
thin iPod with video (30 GB)
Insert 9
iPod with video (60,80 GB)
Insert 10
Use this insert
For this iPod
iPod Touch
thick (60, 80 GB) iPod with video
thick (160 GB) iPod classic
3rd Gen nano
thin (30 GB) iPod with video
thin (80GB) iPod classic
to purchase the proper insert.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Indicators
Top panel
iPod Dock
<< Button
Alarm-1 Button
Preset Button 1-4
iPod Play/Pause Button
Alarm-2 Button
>> Button
Alarm Reset /
Power On/Off Button
Volume + Button
Volume - Button
Wake-to Button
Radio/Aux Button
Sleep Button
Snooze/Dimmer Button
Back panel
Front panel
Clock Adj Button
AM Loop
Time Zone Button
DST Switch
Antenna Socket
Line-in JACK
2
Download from Www.Somanuals.com. All Manuals Search And Download.
iH12 Display
Alarm 1 Indicator
iPod Indicator
Wake-to Indicator
Alarm 2 Indicator
Daylight Saving Time
Indicator
Battery Low Indicator
PM Indicator
Wake-to Radio Indicator
Wake-to Buzzer Indicator
Line in Indicator
Time Display
(AM, FM1 & FM2)
Radio band Indicator
Radio Frequency
or Alarm Time Indicator
Sleep Indicator
(PM) Alarm Time Indicator
Install Clock Backup Batteries
The iH12 uses 2 alkaline “AA” batteries to provide continuous alarm operation
and clock settings in the event of a power failure. If the backup batteries have
been installed and a power failure occurs or the AC cord is accidentally discon-
nected, the display backlight will not remain lit, but current time and alarm time
settings will be temporarily maintained. Otherwise, you must reset the time and
alarm settings.
ᕢ
1. Please make sure the AC adaptor is connected. Otherwise all settings may
be lost during battery replacement.
2. Open backup battery compartment door located on the bottom of the unit.
ᕣ
3. Insert 2 AA batteries, checking that the polarity (+ and – ends of the battery)
matches the drawing near the battery compartment. Close the compart-
ment door.
Installing Backup Batteries
Note: Make sure you dispose of batteries properly (see your local regulations).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Remote Control Unit
iPod Play/Pause Button
Alarm Reset/
Power On/Off Button
>> Button
<< Button
Volume - Button
Volume + Button
Preset Button
3D Button
Radio/Aux Button
Snooze/Dimmer Button
Install/Replace the Remote Control Battery
The remote control battery is already installed at the factory. When the
remote control stops operating or its range seems reduced, it is time
to replace the battery with a new one.
ᕢ
ᕣ
ᕤ
1. The battery door is located on the back end of the remote control.
2. Pull the battery door to release the battery door latch and take out
the battery.
3. Insert a CR2032 battery, checking that the + and – sides of the
battery matches the drawing inside the battery compartment.
4. Replace the battery door.
Installing Remote Battery
Note: Make sure you dispose of batteries properly (see your local regulations).
The Remote Control controls basic functions on the iH12 and certain iPod functions when the iPod is docked in the iH12.
For best results, aim remote control towards the remote sensor on the upper left corner of the unit.
To check for iPod compatibility
iH12 is an advanced system and supports most updated iPod features. To ensure your iPod works properly with the iH12,
please update your iPod firmware with the latest version, available on the Apple website (www.Apple.com).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the iH12
This unit is a PRESET Clock/Radio: the clock is preset for the correct Eastern Standard Time at the factory. Please follow the
steps below to match settings to your location.
1. Depending on your location and whether or not Daylight Saving Time (DST) is in effect, set the DST Switch located on
the back of the unit to +1 to add 1 hour or to -1 to subtract 1 hour. When set to +1 a DST icon will appear on the display,
indicating DST mode.
2. Press and hold the Time Zone Button located on the back of the unit until the current time zone at the lower part of the
display blinks. If needed, press the << or >> Button to select your time zone.
3. Press Time Zone Button again (or if no button is pressed within 10 seconds) to exit the setting mode.
4. If the time showing is not correct, please see Setting Time and Calendar to set the clock.
Setting Time and Calendar
1. Press and hold the Clock Adj Button located on the back of the unit until the time display blinks. Press the << or >>
Button until the current time is displayed. Holding the button for a few seconds will advance or reverse rapidly. Remem-
ber to set the correct AM or PM. An icon in the upper right hand corner of the time digits is the PM Indicator; there is
no AM indicator.
2. Press the Clock Adj Button again to accept the current setting and set current year. Press the << or >> Button until
the current year is displayed. Press the Clock Adj Button to confirm year setting after adjustment.
3. The display will change to show the date blinking. Press the << or >> Button until the current date is displayed. Holding
the button for a few seconds will advance or reverse rapidly.
4. Press the Clock Adj Button again (or if no button is pressed within 10 seconds) to exit the time and date setting mode.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Alarms
Setting the Alarms
1. Press and hold the Alarm-1 or Alarm-2 Button until the alarm time blinks in the lower part of the display. Press the <<
or >> Button to set the alarm time. Holding the button for a few seconds will advance or reverse rapidly. Remember to
set the correct AM or PM time.
2. Press the Wake-to Button to select iPod, Radio or Buzzer alarm source. You can set different alarm sources for each
alarm.
3. Press the Alarm Button again or wait for 10 seconds. Alarm is now armed, indicated by the numbered alarm clock icon.
Review, Arming and Disarming Alarm (Turn Alarm Function On and Off)
1. Press Alarm 1 (or Alarm 2) Button once. The unit will show the alarm time on the bottom part of the display for alarm
time review.
2. During alarm review, press the Alarm 1 or Alarm 2 button again to arm or disarm the alarm. When the alarm is armed,
the related alarm icon appears in display.
Resetting the Alarm to Come on the Next Day
1. When the alarm is sounding, press the Alarm Reset/Power On/Off Button to stop the alarm and reset it to come on
the following day at the same time.
Snooze
1. Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again 9 minutes
later. Snooze can be press several times during the 1 hour alarm cycle.
Sure Alarm
The iH12 has a sure alarm feature. If backup batteries are installed (see page 3) the buzzer alarm will still sound in the event
of a power failure.
Charging your iPod
Note: Please make sure you are using the correct insert for your iPod (see Install iPod Insert) and that it is properly docked
into the iH12. Failure to do so may damage your iPod.
1. While your iPod is docked in the unit and the unit is connected to AC power, it recharges (until fully charged). Note that
non-docking iPods will NOT charge.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to iPod
1. Dock the already playing iPod. The iH12 will automatically turn on and you will hear the music playing from your iPod.
Note: If the playing song/music loudness is too low on the iPod itself, iH12 may not detect iPod is in play mode. Press
the Play/Pause Button on main unit or remote control twice to play it.
2. When the iPod is docked and in standby mode, press the Play/Pause Button on the iH12 or on the remote control to
play it. The iPod Icon will appear on the display, showing iPod playing mode.
3. Press the iPod Play/Pause Button again to pause play; press again to resume it.
4. Press the Volume+ and Volume– Button on the iH12 or on the remote control to adjust the system volume.
5. Press >> or << Button on the iH12 or on the remote control to go to the next or previous track. Press and hold while
track is playing for high speed forward or reverse music search of the current track.
6. To turn off the unit, press the Alarm Reset/Power On/Off Button on the iH12 or on the remote control to turn it off.
Your iPod will continue charging while in the dock.
Listening to non-docking iPod or other portable audio devices
If you are using an iPod without a docking port or other MP3 player or portable audio device, you can play it through the iH12
via the Line-in Jack.
1. Plug one end of an audio patch cord (available at www.ihomeaudio.com) into the headphone or line-out jack on your
device and the other end of the patch cord into the iH12 Line-in Jack, located on the back of the unit.
2. Press the Radio/Aux Button on the iH12 or on the remote until the Line-in Icon appears on the right hand lower corner
of the display, indicating Line-in playing mode.
3. Turn on and play your device.
4. Press the Volume+ and Volume– Button on the iH12 or on the remote control to adjust the system volume. You may
need to adjust your device volume, too.
5. To turn off the unit, press the Alarm Reset/Power On/Off Button on main unit or remote control to turn it off. Please
remember to turn off your device, too.
Dimmer Operation
During normal operation, press the Snooze/Dimmer Button to control the brightness of the LCD display.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Radio
Setting up Antenna
1. Plug the AM antenna cable into the AM Loop Antenna Socket on the back of unit. Move antenna 12” away from unit
for best reception.
2. Extend FM wire antenna fully for best reception. Do not strip, alter or attach to other antennas.
Tuning and Playing the Radio
1. Press the Radio Button to select radio play mode. Press as needed to select AM, FM1 or FM2 radio band.
2. Press << or >> Button to tune radio to a desired station.
3. To memorize the current station as a preset, press and hold Preset Button 1, 2, 3 or 4. Repeat step 1-3 to preset up
to 12 stations (4 AM and 8 FM). To listen to a preset station at any time, simply press the desired preset button.
4. Press the Volume+ and Volume– Button on the iH12 or on the remote control to adjust the system volume.
5. To turn off the unit, press the Alarm Reset/Power On/Off Button on the iH12 or on the remote control to turn it off.
Sleep Operation
Sleep mode lets you sleep to your iPod or the radio, gradually lowering the volume until the unit shuts off at the selected
time.
1. Press the Sleep Button to enter sleep mode. The Sleep Icon will appear on the display to indicate the unit is in sleep
mode. The unit will automatically turn off after the selected time. Sleep mode has a Gentle Sleep feature which gradually
lowers the volume 15 seconds before auto power off.
2. You can adjust the sleep timer from 120, 90, 60, 30 or 15 minutes by pressing the Sleep Button again.
3. When the display changes back to show the real time, press the Sleep Button once to show the sleep time remaining.
Pressing it again will change the sleep time to the next lowest increment.
4. The iH12 has independent volume setting for sleep mode so you can adjust the sleeping volume without affecting the
alarm volume. Press the Volume+ and Volume– Button on main unit or remote control to adjust the sleep volume. The
sleep volume will remain at that level the next time you enter sleep mode until controls are changed.
5. To stop listening at any time, press the Alarm Reset/Power On/Off Button on the iH12 or on the remote control to
turn it off.
Click Sound Operation
During normal operation, press and hold the Wake-to Button to set button click sound on or off. After the display shows
“CLC”, press << or >> Button to set click sound on or off, then wait around 5 seconds to exit the setting mode.
3D Sound Operation
Repeatedly press the 3D Button on the remote to set 3D wide sound effect on or off, then wait around 5 seconds to exit the
setting mode.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully
before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in
these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For
example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it
should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through
the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where
it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning
instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings
or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage
to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in
a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A. the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E. the unit exhibits a marked change in performance or does not operate normally.
12. Antenna – Do not connect an external antenna to the unit (other than that provided).
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power
cable should be unplugged from the unit to prevent damage or corrosion.
14. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting
Symptom
Possible Problem
Solution
Unit doesn’t respond AC adaptor isn’t plugged to a wall outlet or
Plug the AC adaptor into a wall outlet and plug the connector into
the power supply jack on the unit
(no power)
the connector is not plugged into the power
supply jack on the back of the unit
Wall outlet is not functioning
Using no or wrong iPod insert
iPod is not installed properly
Plug another device into the same outlet to confirm the outlet is working
Make sure the dock insert is the proper fit for your iPod
iPod cannot dock
properly
Remove your iPod from the connector and check for any
obstruction on the connectors in the dock and on your iPod.
Then reseat it in the dock.
iPod does not
respond to the unit
Remove your iPod from the connector and check for any
obstruction on the connectors in the dock and on your iPod.
Then reseat it in the dock.
iPod is not installed properly
Upgrade software on your iPod. For details, visit
Your iPod software is too old
iPod is locked up
Please make sure your iPod is working properly before docking
it to the unit. Please refer to your iPod manual for details on
iPod operation.
st
nd
Using 1 or 2 generation iPod or other device iH12 cannot control those iPods or other devices.
iPod didn’t charge
up
iPod is not installed properly
Remove your iPod from the connector and check for any
obstruction on the connectors in the dock and on your iPod.
Then reseat it in the dock.
iPod is locked up/frozen
iPod battery has problem
Volume level is set too high
Sound source is distorted
Please make sure your iPod is working properly before docking
it to the unit. Please refer to your iPod manual for details.
Sound is distorted
Decrease the volume.
If iPod original sound source is poor quality, distortion and noise
are easily noticed with high-power speakers.
Try a different audio source such as a music CD.
If you are using an iPod Shuffle or external sound source like
older generation iPod, try reducing the output volume on the
device itself. Also, try turning bass boost OFF.
Remote Control
didn’t work
Battery weak
Replace with new battery
Remote Control is not pointed toward the
IR sensor
Point the Remote Control toward the IR sensor, within 10 feet of
the unit.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Solución De Problemas
Síntoma
Posible Problema
Solución
La unidad no
funciona (no circula
corriente eléctrica)
El adaptador de AC no está conectado al
Conecte el adaptador de AC al tomacorriente y también
tomacorriente o el conector no está conectado conecte el conector a la ficha en la parte posterior de la unidad
a la ficha en la parte posterior de la unidad
El tomacorriente no funciona
Coloque otro aparato en ese mismo tomacorriente para
confirmar si el que no funciona es el tomacorriente
El iPod no encastra
correctamente
No ha colocado el encastre del iPod, o está
utilizando el encastre incorrecto.
Verifique que el encastre sea el apropiado para su iPod
El iPod no encastra correctamente
El iPod no está instalado correctamente
Su software es obsoleto
Quite el iPod del encastre y retire la posible obstrucción del
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.
El iPod no se
comunica con la
unidad
Quite el iPod del encastre y verifique posibles obstrucciones del
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.
Renueve su software. Para mayor información, diríjase a
El iPod no responde
Verifique que su iPod funcione correctamente antes de conectarlo
a la unidad. Refiérase al manual de su iPod para más detalles.
Usted tiene un iPod de primera o segunda
generación, un Shuffle u otro tipo de aparato
El iH12 no puede controlar estos otros aparatos
El iPod no carga
El iPod no está instalado correctamente
Quite el iPod del encastre y retire la posible obstrucción del
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.
El iPod está trabado/no responde
Por favor asegúrese de que su iPod funcione correctamente
antes de colocarlo en el encastre. Refiérase al manual de su
iPod para mayor información.
La batería del iPod podría tener algún
inconveniente
El sonido sale
distorsionado
El volumen se encuentra muy alto
Baje el volumen y no EQ
El sonido sale distorsionado de la unidad
Si el sonido original de su iPod era de pobre calidad, las
distorsiones y ruidos se harán más notables con los
parlantes de alta potencia. Pruebe utilizar otra fuente de
audio como un CD.
Si está utilizando un iPod de primeras generaciones o un
Shuffle, intente bajar el volumen de su aparato. También intente
apagar el amplificador de bajos
El control remoto no
funciona
Las baterías están gastadas
Reemplace las baterías por nuevas
No está apuntando el control remoto hacia
el iH12
Apunte el control remoto hacia el iH12 y manténgase a una
distancia máxima de 10 pies de la unidad.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited 90-Day Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects
in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should
this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies
will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage,
and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center
listed below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase is $20.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries
are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($20.00 without proof of purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Drive
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may
not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies
product.
© 2008 SDI Technologies, Inc. All rights reserved
or call 1-800-288-2792 Toll Free
iH12-030108-0
Printed in China
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|