i Tech Dynamic Headphones Clip V User Manual

2005 Hutchison Harbour Ring Enterprises Limited  
All rights in this publication are reserved and no part may  
be reproduced without the prior written permission of  
the publisher. The contents of this publication are  
believed to be correct at the time of going to press, but  
any information, specifications, products or services  
mentioned may be modified, supplemented or  
withdrawn without further notice.  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received,  
including interference that may cause undesired  
operation.  
Caution: Changes or modifications not expressly  
approved by the party responsible for compliance could  
void the user's authority to operate the equipment.  
i.Tech Clip V  
The Stylized i.Tech logos are trademarks owned by  
Hutchison Harbour Ring Enterprises Limited or its  
affiliates.  
i.Tech declares under our sole responsibility that the  
headset is in conformity with the provisions of the  
following Council Directives: 1999/5/EC  
Bluetooth® and the Bluetooth logos are trademarks  
owned by Bluetooth SIG, Inc, USA and licensed to i.Tech  
Dynamic Limited.  
Download from Www.Somanuals.com. All MaUnusaelsrSGeuaricdheAnd Download.  
01/2006  
S3J-51A05054-03  
Table of Contents  
Voice Dialing from Your Headset ..................................................................................................................... 11  
Last Number Redialing from Your Headset ................................................................................................... 12  
Rejecting a Call (Handsfree Profile ONLY) …………........................................................................................ 12  
Transferring a Call (Handsfree Profile ONLY) …………................................................................................... 12  
Adjusting the Volume ..................................................................................................................................................... 13  
Resettingthe Headset ..................................................................................................................................................... 13  
Care and Maintenance .................................................................................................................................................... 14-15  
Headset ................................................................................................................................................................. 14  
Built-in Battery .................................................................................................................................................... 15  
Charger .................................................................................................................................................................. 15  
Safety Information ........................................................................................................................................................... 16  
Troubleshooting ................................................................................................................................................................ 17-18  
Product Specifications ..................................................................................................................................................... 19  
Declaration of Conformity (DoC) ................................................................................................................................... 20  
i.Tech Clip V Overview ...................................................................................................................................................... 1  
Getting Started ................................................................................................................................................................. 2  
Charging Your Headset ................................................................................................................................................... 3-5  
Charging Time ......................................................................................................................................................  
Talk and Stand-by Time .....................................................................................................................................  
Low Battery ..........................................................................................................................................................  
4
4
5
Turning your Headset On and off ................................................................................................................................ 5-6  
Pairing Your Headset ...................................................................................................................................................... 7-9  
Using Your Headset ......................................................................................................................................................... 9-12  
Answering a Call .................................................................................................................................................. 9  
Ending a Call ......................................................................................................................................................... 10  
Dialing from Your Mobile Handset .................................................................................................................. 10  
Muting the Built-in Buzzer …….......................................................................................................................... 10  
Muting the Microphone ………........................................................................................................................... 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
00  
00  
i.Tech Clip V Overview  
Getting Started  
1
2
3
1. Microphone  
2. Volume Key  
3. Status Indicator  
4. Built-in Buzzer  
5. Charging Socket  
6. Built-in Rechargeable Battery  
7. Multi-function Button (MFB)  
8. Earphone  
6
7
To use your i.Tech Clip V (“the headset”), please follow  
these simple steps:  
4
5
Charge your headset  
8
Pair your headset with a Bluetooth-enabled mobile handset  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01  
02  
Charging Your Headset  
Charging Your Headset  
Connect the charger to an AC wall outlet (mains socket) and the charger plug to the headset’s charging socket  
(fig.1). The LED will be red while charging.  
IMPORTANT Charging indication will be delayed for a few seconds if the headset has not been used for a long  
time or the battery is drained.  
Charging Time  
Charging the battery fully is normally within 3 hours. When the battery is fully charged, the LED will turn blue and  
remain on. Disconnect the charger from AC wall outlet (mains socket) and the headset. Press and hold the MFB  
(fig.1) for 2 seconds to turn the headset on, please refer to “Turning Your Headset On and Off” .  
The Headset comes with a built-in  
rechargeable battery. Prior to using the  
headset, it is recommendable to charge the  
battery fully for the first time.  
Charging  
Socket  
Charger  
Talk & Standby Time  
Charger Plug  
The fully charged battery offers up to 6 hours talk time and up to 120 hours standby time. When no calls are in  
progress, the headset remains turned on in standby mode.  
Download from (Wfig.w2) w.Somanuals.com. All Manuals Search And Download.  
(fig.1)  
03  
04  
Low Battery  
Turning Your Headset On and Off  
When the headset is on and the battery becomes low, the status indicator flashes red and the  
headset emits a beep every 1 minute. Please recharge the battery as described above.  
If you are setting up the headset and your mobile phone in a noisy environment, we advise  
you to put on the earphone first so that the beep will be more audible.  
Turning Your Headset On and Off  
Turning Off the Headset  
Press and hold the MFB for approximately 3 seconds until you hear a long beep. The status indicator will stop  
flashing.  
Turning On the Headset  
Press and hold the MFB for 2 seconds until you hear a short beep. The status indicator will then flash blue.  
IMPORTANT Press the MFB again after the headset switched on each time you turn on the headset to reactivate  
pairing so that the connection between the headset and the mobile handset is resumed. For pairing , please refer to  
“Pairing Your Headset” on page 7-8.  
IMPORTANT To disconnect the Bluetooth connection, press the MFB firmly to turn off your headset. If you will  
not be using the headset for a while, you should consider turning off the Bluetooth function on your mobile  
phone as well.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
05  
06  
7. Press “Return” to go back to your mobile handset’s main menu. For certain mobile handset models, a headset  
icon will be shown on the screen. You should now be able to make and receive calls using your headset.  
IMPORTANT If the pairing cannot be completed within 2 minutes while the pairing mode is activated, the headset  
status indicator flashes purple followed by 3 beeps and the headset is turned off. Please repeat the above pairing  
procedures.  
Ending a Call  
Press the MFB to end your call or end the call via your mobile handset in the normal way.  
Dialing from Your Mobile Handset  
Simply make calls on your mobile handset in the normal way.  
Muting the Built-in Buzzer  
Using Your Headset  
Press and hold the volume key for two seconds until status indicator flashes RED once to mute the Buzzer and press  
and hold the volume key for 3 seconds to deactiveate the muting function while your mobile phone remains in  
standby mode.  
Answering a Call  
When there is an incoming call, you will hear ringing through the earphone and the built-in buzzer. Press the MFB  
to accept the call or answer the call via your mobile handset in the normal way.  
IMPORTANT: If you do not wish to be disturbed at all, you may consider resetting the mobile phone setting to  
restrict incoming calls. Please refer to your mobile phone user guide for set up details.  
IMPORTANT ou can stop the buzzer alert by pressing the volume key once. The buzzer will ring again when there is  
another incoming call.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
09  
10  
Using Your Headset  
Last Number Redialling from Your Headset  
Short press the MFB on your headset twice.  
Muting the Microphone  
IMPORTANT The above functions are only applicable to mobile handsets with Bluetooth Handsfree Profile.  
Functionality varies depending on the mobile handset model you have. Please refer to your mobile handset user  
guide for additional information.  
You can put a call on hold by muting the microphone.  
Press and hold the volume key for two seconds until status indicator flashes Red to mute built in Microphone  
and press and hold the volume key for 3 seconds to deactivate the muting function while conversation.  
Rejecting a Call (Handsfree Profile ONLY)  
Press and hold the volume key then press and hold the MFB until the incoming call is rejected.  
Voice Dialling from Your Headset  
If your mobile handset is equipped with a voice dialling function, simply press the MFB on your headset, and  
when you hear a beep say the voice tag.  
Transferring a Call (Handsfree Profile ONLY)  
Press and hold the volume then press and hold the MFB until the audio is transferred from headset to your  
mobile handset during conversation.  
IMPORTANT Please make sure voice tag into the mobile handset first before using voice dialling function.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
12  
Adjusting the Volume  
Care and Maintenance  
Press the Volume Key repeatedly until you reach the desired volume level. The listening volume may be affected  
by the volume setting of the caller’s phone as well. Re-adjust the listening volume again when necessary.  
Headset  
Consider turning your headset off before placing it in your pocket or bag. If the MFB is accidentally depressed,  
your mobile handset may place an unintended call.  
Do not expose the headset to liquid, moisture or humidity as it is not waterproof.  
Do not use abrasive cleaning solvents to clean the headset.  
Do not expose the headset to extremely high or low temperatures.  
Resetting the Headset  
You may reset the headset to its original settings at anytime, in doing this you also clear all current pairing  
settings.  
1. Ensure the headset is OFF.  
2. Press and hold the volume key for 20 seconds until the status indicator flashes Red and Blue.  
3. Release the Volume Key.  
Do not dispose of the headset in a fire as it will result in explosion.  
Do not expose your headset to contact with sharp objects as this will cause scratches and damage.  
Do not stick anything inside the headset as this may damage internal components.  
Do not attempt to disassemble the headset as it does not comtain serviceable components.  
If you do not use the headset for long periods, be sure to store it in a dry place, free from extreme tempera-  
tures and dust.  
4. Press and hold the Volume Key again until you hear 2 beeps.  
5. Recharge the headset for a few seconds.  
The headset is turned off and returns to the original settings. All current pairings are cleared.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
14  
Safety Information  
Built-in Battery  
Check local laws regarding use of a mobile handset and headset whilst driving. If you use the headset while  
driving, ensure your attention and focus remain on the road and you drive in a responsible and safe manner.  
Never allow children to play with the headset – small parts may be a choking hazard.  
Observe all signs that require an electrical device or RF radio product to be switched off in designated areas.  
These could include hospitals, blasting areas, and potentially explosive environments.  
Turn off your headset prior to boarding an aircraft. Do not use your headset in an aircraft.  
Never mount or store your headset over any air bag deployment area as serious injury may result when an air  
bag deploys.  
Do not attempt to replace the headset’s battery yourself as it is built into the headset and is not changeable.  
Charge the battery in accordance with the instruction supplied with this user guide.  
Only use the manufacturer supplied charger when charging the headset.  
Charger  
Only use the manufacturer supplied charger when charging the headset.  
Do not disassemble the charger as it may expose you to dangerous voltages or other risks. Incorrect  
reassembly can cause electric shock when the headset is subsequently used.  
Do not use the charger outdoors or in damp areas.  
Only charge the headset’s built-in battery in accordance with the instructuins in this user guide.  
Avoid charging the headset in extremely high or low temperatures.  
Do not open or mutilate the built-in battery.  
Dispose of batteries according to local regulations. Do not dispose as household waste.  
Dispose of the packaging and this product in accordance with the latest provisions.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
16  
Troubleshooting  
Troubleshooting  
If you are unable to connect your headset with your mobile handset or Bluetooth enabled device, please try the  
following:  
Ensure your headset is turned on and is properly charged.  
Ensure the headset is paired with your mobile handset.  
Ensure your mobile handset’s Bluetooth feature is activated.Please refer to your mobile handset user guide for  
specific instruction.  
The i.Tech Clip V Headset is compliant with and adopts the Bluetooth Specification 1.2. However, interoperability  
between the device and other Bluetooth-enabled products is not guaranteed because it depends on  
compatibility. For more information on the compatibility between the device with other Bluetooth-enabled  
products, please check with the manufacturer or browse:  
Ensure the headset is within a maximum of 10 meters of your mobile handset(s) and there are no obstructions,  
such as walls or other electronic devices in between.  
If the above suggestions do not solve your problem, please recharge the headset and remove your mobile phone  
battery for a while. Then start pairing again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
18  
Product Specifications  
Declaration of Conformity ( DoC )  
We, i.Tech Dynamic Ltd., declare that the following product:  
Bluetooth Specification:  
Bluetooth Profile Supported:  
Range of Frequency:  
Talk Time*:  
Version 1.2 Class 2  
Headset and Handsfree  
2.4GHz Spectrum  
up to 6 hours  
Product Name: i.Tech Clip V  
Model No.: C51-A05054-XX  
Is in conformity with the following essential requirements of Council Directive 1999/5/EC ( referred to as  
R&TTE Directive ) : Article 3.1a, 3.1.b and 3.2. and the product is manufactured in accordance with Annex II of  
above directive.  
Standby Time* :  
up to 120 hours  
Nominal Charging Time:  
Dimensions:  
Within 3 hours  
A copy of the Declaration of Conformity can be found at:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
46(L) x 18(W) x 22.5(H) mm  
16.7 grams  
* May vary due to users’ operation  
mode and mobile phone settings.  
Weight:  
20  
19  

Hand Held Products Scanner IT3800 User Manual
HANNspree Computer Monitor HF257 User Manual
Hearth and Home Technologies Range be 36 c User Manual
Hotpoint Refrigerator RFR50V User Manual
HP Hewlett Packard Personal Computer DX2390 User Manual
HP Hewlett Packard Scanner 4500c User Manual
Husqvarna Lawn Mower Accessory 968999211 User Manual
Hyundai Microwave Oven MWEGH 281S User Manual
IBM Home Theater Server SB84 0449 00 User Manual
Impex Fitness Equipment MD 857 User Manual