NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
IRON GRIP STRENGTH
Deluxe Olympic Bench
TSA-5762
Warranty
Ordering Parts
Model
TSA-5762
Retain This
Manual for
Reference
06-27-05
OWNER'S
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
3. Maximum weight capacity 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL PLACEMENT
The Warning Label shown here has been placed on the Upright Beam. If the label is missing or illegible, please
call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Push four ∅3” End Caps (#31) onto the bases of Right & Left Upright Beams (#1 &
#2).
B.) Connect the Left & Right Upright Beams (#1 & #2) by a Cross Brace (#3) in the mid-
span. Align the holes and secure each end with two M10 x 3 ¾” Carriage Bolts (#47),
one 5 ½” x 3 3/8” Bent Bracket (#24), two ∅ ¾” Washers (#59), and two M10 Aircraft
Nuts (#46).
C.) Place the Backrest Adjustment Bar (#16) onto the selected slot on the Upright Beams.
D.) Slide a Glider (#10) onto a Guide Rod (#14) from the bottom.
E.) Slide a Safety Stop (#11) onto the Guide Rod from the bottom. Attach a Safety Catch
Hook (#23) to the Safety Stop. Secure it with one M10 x 1” Allen Bolt (#52), two Ø ¾”
Washers (#59), and one M10 Aircraft Nut (#46).
F.) Attach and secure the top of the Guide Rod to the Right Upright Beam (#1) with one
M10 x 1” Allen Bolt (#52) and Ø ¾” Washer (#59). Secure the bottom to the base with
one M10 x 3 ¾” Allen Bolt (#49) and Ø ¾” Washer (#59).
G.) Repeat Procedures D, E, and F above to install the other side.
H.) NOTE: Help of another person to install the Weight Bar in this step is strongly
recommended. Place the Lifting Sleeve (#13) in between the two Gliders (#10). Align
the holes and insert the Weight Bar (#15) into the Glider from one end through the
Lifting Sleeve to the other Glider on the opposite side. Secure the Weight Bar with two
M8 x 3/8” Allen Bolts (#56).
I.) Attach two Long Olympic Sleeves (#33) onto the Weight Bar from both ends. Secure
the Sleeve to the Weight Bar with the screw on the Sleeve. Attach a Spring Clip (#27)
to each Sleeve.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Main Seat Support (#4) to the Cross Brace (#3). Secure it with one 5 ½” x 3”
Bent Bracket (#25), four M10 x 2 3/8” Carriage Bolts (#48), four Ø ¾” Washers (#59)
and four M10 Aircraft Nuts (#46).
B.) Attach the seat support frame on the Leg Developer Holder (#5) to the bracket on the
Main Seat Support (#4). Secure it with one M10 x 2 ¾” Allen Bolt (#50), two Ø ¾”
Washers (#59), and one M10 Aircraft Nut (#46). Do not tighten the Nut and Bolt yet.
C.) Attach the bottom of Leg Developer Holder (#5) to the Main Seat Support. Secure it
with one Bracket (#19), two M10 x 2 3/8” Allen Bolts (#51) and two Ø ¾” Washers
(#59). Securely tighten all the Nuts and Bolts previously installed.
D.) Place the Seat (#22) onto the seat support frame on the Leg Developer Holder. Secure
it with four M8 x 5/8” Allen Bolts (#55) and Ø 5/8” Washers (#58).
E.) Thread the Lock Knob (#29) into the hole on the Leg Developer Holder.
F.) Insert a Foam Tube halfway through the hole on the Leg Developer Holder. Push two
Vinyl Foam Rolls (#32) onto the Tube from both ends. Push two Foam Roll End Caps
(#39) into the ends.
DIAGRAM 2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Backrest Incline Support (#12) in between the two side-holes on the
Backrest Supports (#17). Attach the Backrest Supports to the pivot on the Main Seat
Support (#4). Secure it with one M12 x 7 ½” Allen Bolt (#53), two ∅ 1” Washers (#60),
and one M12 Aircraft Nut (#45).
B.) Place the other end of Backrest Supports rest against the Backrest Adjustment Bar.
C.) Place the Backrest Board (#21) onto the Backrest Supports (#17). Secure it with four
M8 x 1 5/8” Allen Bolts (#54) and Ø 5/8” Washers (#58).
D.) Attach the Leg Developer (#6) to the Leg Developer Holder (#5). Secure it with one
Axle (#28), two M10 x 1” Allen Bolts (#52), and two Ø ¾” Washers (#59).
E.) Insert two Foam Tubes (#18) halfway through the holes on the Leg Developer. Push
four Vinyl Foam Rolls (#32) onto the Tubes. Push four Foam Roll End Caps (#39) into
the Tubes from both ends.
F.) Attach a Short Olympic Sleeve (#34) to the weight post on the Leg Developer. Attach a
Spring Clip (#27) to the Sleeve.
G.) Attach the Curl Bar Handle (#9) to the bracket on the Leg Developer. Secure it with a
L-shaped Lock Pin (#26).
H.) Attach the Arm Curl Pad (#20) to the Arm Curl Stand (#7). Secure it with two M8 x 5/8”
Allen Bolts (#55) and Ø 5/8” Washers (#58). Insert the Arm Curl Stand into the opening
on top of Leg Developer Holder. Secure it with the Lock Knob.
I.) Remove the Arm Curl Stand and Curl Bar Handle when doing Leg exercises.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO DESCRIPTION
Q’ty
1
2
3
Right Upright Beam
Left Upright Beam
Cross Brace
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
2
3
1
1
1
1
2
2
1
1
3
1
1
2
4
6
2
1
8
2
2
2
6
1
1
2
2
1
1
11
4
4
2
50
51
52
53
54
55
56
57
58
59
60
61
M10 x 2 ¾” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 1” Allen Bolt
M12 x 7 ½” Allen Bolt
M8 x 1 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
M8 x 3/8” Allen Bolt
Philips Screw
Ø 5/8” Washer
Ø ¾” Washer
Ø 1” Washer
Ø 1 ½” Bushing
1
2
6
1
4
6
4
1
10
4
5
6
7
8
9
Main Seat Support
Leg Developer Holder
Leg Developer
Arm Curl Stand
Curl Bar Handle Support
Curl Bar Handle
Glider
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
22
Safety Stop
Backrest Incline Support
Lifting Sleeve
Guide Rod
Weight Bar
Backrest Adjustment Bar
Backrest Support
Foam Tube
Bracket
Arm Curl Pad
Backrest Board
Seat
Safety Catch Hook
5 ½” x 3 3/8” Bent Bracket
5 ½” x 3” Bent Bracket
L-shaped Lock Pin
Spring Clip
Axle
Lock Knob
∅ 3” Con-shaped End Cap
Ø 3” End Cap
2
2
1
1
2
1
#4 Allen Wrench
#5 Allen Wrench
#6 Allen Wrench
#8 Allen Wrench
Vinyl Foam Roll
Long Olympic Sleeve
Short Olympic Sleeve
1 ½” Sleeve
Bushing
Axle Bushing
Grip
Foam Roll End Cap
Ø 1” End Cap
∅ 1” Con-shaped End Cap
1” Square End Cap
Ø 2 3/8” End Cap
Ø 3” Sleeve
M12 Aircraft Nut
M10 Aircraft Nut
M10 x 3 ¾” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
M10 x 3 ¾” Allen Bolt
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|