NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
APEX
Combo Bench w/ Wt. Set
Hardware Identifier
Assembly Instruction
Parts List
TSA-499
Warranty
Ordering Parts
Model
TSA-499
Retain This
Manual for
Reference
08-03-05
OWNER'S
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
3. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL PLACEMENT
The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible, please
call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the Left & Right Upright Beams (#1 & 2) by a Cross Brace (#8) in the mid-span.
Align the holes and secure each end with one 4 ¾” x 3 1/8” Bracket (#17), two M10 x 2 3/8”
Carriage Bolts (#41), ∅ ¾” Washers (#49), and M10 Aircraft Nuts (#48).
B.) Insert the Backrest Adjustment Bar (#9) through the selected holes on the Upright Beams.
C.) Insert the Left & Right Safety Catches (#12 & 13) into the selected holes on the Left &
Right Upright Beams.
DIAGRAM 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Leg Developer Holder (#4) to the Front Stabilizer (#3). Secure it with two
M10 x ¾” Allen Bolts (#45) and Ø ¾” Washers (#49).
B.) Attach the Leg Developer Holder to the Main Seat Support (#5). Secure it with two M10
x 2 3/8” Carriage Bolts (#41), Ø ¾” Washers (#49), and M10 Aircraft Nuts (#48)
horizontally. Secure it with one M10 x 2 1/8” Carriage Bolt (#42), Ø ¾” Washer (#49),
and M10 Aircraft Nut (#48) vertically.
C.) Attach the Main Seat Support to the Cross Brace (#8). Secure it with a 4 3/8” x 1 ½”
Bracket (#26), two M10 x 2 3/8” Carriage Bolts (#41), two ∅ ¾” Washers (#49), and two
M10 Aircraft Nuts (#48).
D.) Insert the T-shaped Lock Pin (#22) into the hole on the Main Seat Support.
DIAGRAM 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#6) to the Leg Developer Holder (#4). Secure it with one M10 x 2
7/8” Allen Bolt (#44), two Ø ¾” Washers (#49), and one M10 Aircraft Nut (#48).
B.) Insert two Foam Roll Tubes (#16) halfway through the holes on the Leg Developer (#6). Push
four Foam Rolls (#27) onto the Tubes from both sides.
C.) Attach a Spring Clip (#37) onto the weight post on the Leg Developer.
D.) Slide the Sliding Weight Post (#11) onto the Lat Bar Frame (#7). Insert the Lat Bar Frame into
the opening on the Leg Developer Holder.
E.) Thread a Lock Knob (#38) into the hole on the back of Leg Developer Holder to secure the
Lat Bar Frame. Attach a Spring Clip (#37) onto the weight post on the Sliding Weight Post.
DIAGRAM 3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the side-holes on the Backrest Supports (#15) to the pivot on the Main Seat
Support (#5). Place the other end of Backrest Supports rest against the Backrest
Adjustment Bar.
B.) Attach the Backrest Board (#18) to the Backrest Supports. Secure it with four M6 x 1
3/8” Hex Bolts (#46) and Ø ½” Washers (#50).
C.) Place the Seat (#19) onto the Main Seat Support. Secure it with four M6 x 1 3/8” Hex
Bolts (#46) and Ø ½” Washers (#50).
D.) Use the T-shaped Lock Pin to hold the Backrest Board at vertical position. Note: The
Pin is not designed to sustain any weight. The only purpose is to hold the backrest
board at vertical position while doing squat exercise from the back of the bench.
DIAGRAM 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Cable (#20) to the open slot on the top of the Lat Bar Frame (#7). Attach a
Pulley (#35) to the Cable. Secure the Pulley to the open slot with one M10 x 2 1/8”
Allen Bolt (#43), two Pulley Bushings (#21), and one M10 Aircraft Nut (#48).
B.) Draw the Cable around the Pulley and down to the bracket on the Sliding Weight Post
(#11). Secure the Cable to the bracket with one M10 x 1” Allen Bolt (#52), two Ø ¾”
Washers (#49), and one M10 Aircraft Nut (#48).
C.) Connect the Lat Bar (#10) to the Cable with a C-clip (#36).
DIAGRAM 5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Left Upright Beam
Right Upright Beam
Front Stabilizer
Leg Developer Holder
Main Seat Support
Leg Developer
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
2
1
4
2
4
1
4
6
2
3
2
9
1
4
1
1
4
1
2
3
8
1
1
1
2
8
2
12
15
8
1
1
1
Lat Bar Frame
Cross Brace
9
Backrest Adjustment Bar
Lat Bar
Sliding Weight Post
Left Safety Catch
Right Safety Catch
Weight Bar
Backrest Support
Foam Roll Tube
4 ¾” x 3 1/8” Bracket
Backrest Board
Seat
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Cable
Pulley Bushing
T-Shaped Lock Pin
Weight Plate #10
Weight Plate #5
Weight Plate #2.5
4 3/8” x 1 ½” Bracket
Foam Roll
1 5/8” x 3 1/8” End Cap
1 ¾” Square End Cap
1 ½” Square End Cap
1” Square End Cap
Ø 1” Con-shaped End Cap
Ø 1” End Cap
Ø ¾” Con-shaped End Cap
Pulley
C-clip
Spring Clip
Lock Knob
Lat Bar Grip
Sleeve
M10 x 2 3/8” Carriage Bolt
M10 x 2 1/8” Carriage Bolt
M10 x 2 1/8” Allen Bolt
M10 x 2 7/8” Allen Bolt
M10 x ¾” Allen Bolt
M6 x 1 3/8” Hex Bolt
Bushing
M10 Aircraft Nut
Ø ¾” Washer
Ø ½” Washer
1 ¼” Square End Cap
M10 x 1” Allen Bolt
T-shaped Handle
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|