NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
MARCY POWER SURGE
WEIGHT BENCH
Warranty
Ordering Parts
Model
PWR SURGE
Retain This
Manual for
Reference
07-23-01
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF
35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO
RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY
OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended this machine to be assembled by two
or more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the Right and Left Upright Beams (#1) & (#2) by a Cross Brace (#4) in the mid-
span. Align the holes then secure the out side of the Upright Beam with a large Washer
(#59) and M10 x 1” Allen Bolt (#55) on each end of the Cross Brace.
B.) Align the holes and secure them with two Brackets (#26), four M10 x 3 ½” Carriage
Bolts (#41), four ∅ ¾” Washers (#44), and four M10 Aircraft Nuts (#47) on each end of
the Cross Brace.
C.) Place Backrest Adjustment Bar (#3) between the two Upright Beams on the selected
bar holder to obtain desired incline of Backrest.
D.) Attach two Squat Bar Catches (#13) to the top of the Upright Beams. Secure them with
two L-shaped Pins (#48).
E.) Insert the Left Bar Catch (#10) into the selected hole on the Left Upright Beam (#2).
Turn the Bar Catcher clockwise to lock it. Repeat the same step for the other side.
DIAGRAM 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Slide the Sliding Block (#7) onto the Main Seat Support (#6). Secure it with a ∅ 3/8” Lock
Knob (#50) to a selected hole on the Main Seat Support.
B.) Attach the Front Stabilizer (#8) to the Main Seat Support (#6). Secure it with one M10 x 2
½” Carriage Bolt (#60), two M10 x 2 ¾” Carriage Bolts (#42), ∅ ¾” Washers (#44), and
M10 Aircraft Nuts (#47).
C.) Attach the back of Main Seat Support (#6) to the Cross Brace (#4). Secure it with two
Brackets (#26), four M10 x 2 ¾” Carriage Bolts (#42), ∅ ¾” Washers (#44), and M10
Aircraft Nuts (#47).
D.) Insert the Leg Developer Holder (#16) into the opening on the Front Stabilizer (#8). Secure
it with a ∅ ½” Lock Knob (#57).
E.) Attach two Backrest Supports (#5) to the long pivot on the Sliding Block (#7). Place the
Headrest Bracket (#12) in between the two Backrest Supports (#5). Align the holes and
lock the desired Headrest position with a Lock Pin (#56).
F.) Attach the Seat Bracket (#9) to the short pivot on the Sliding Block (#7). Secure it with one
M10 x 4 ¾” Allen Bolt (#37), two ∅ ¾” Washers (#44), and one M10 Aircraft Nut (#47).
DIAGRAM 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#15) to the bracket on the Leg Developer Holder (#16). Secure
it with an Axle (#24), two ∅ ¾” Washers (#44), and two M10 x 5/8” Allen Bolts (#38).
B.) Insert one Foam Roll Tube (#21) halfway through the holes on the Leg Developer Holder
(#16). Then insert two Foam Roll Tubes (#21) halfway through the holes on the Leg
Developer (#15). Push six Foam Rolls (#28) onto the Tubes from both sides. Plug six
Foam Roll End Caps (#36) to the ends. Slide the Olympic Sleeve (#27) onto the weight
post in front of the Leg Developer. Attach the Olympic Spring Clip (#29) to the Sleeve.
C.) NOTE: When using the decline position to do Ab exercise, place at least 30lbs of weights
on the post to hold down the Leg Developer.
ꢀ
ꢀ
ꢀ
DIAGRAM 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Place the Headrest Board (#17) onto the Headrest Bracket (#12). Secure it with two M8
x ¾” Allen Bolts (#43) and ∅ 5/8” Washers (#46).
B.) Place the Backrest Board (#18) onto the Backrest Supports (#5). Secure it with four M6
x 1 3/8” Hex Bolts (#39) and ∅ ½” Washers (#45).
C.) Place the Seat Pad (#19) onto the Seat Bracket (#9). Secure it with four M8 x 5/8” Allen
Bolts (#40) and ∅ 5/8” Washers (#46). Insert a L-shaped Pin (#48) into the selected
hole on the Seat Bracket (#9) to obtain the desired incline of the Seat.
D.) Attach the Arm Curl Pad (#52) to the Arm Curl Stand (#14). Secure it with two M8 x 5/8”
Allen Bolts (#40) and ∅ 5/8” Washers (#46). Insert the Stand into the holder behind the
Right Upright Beam. For Arm Curl exercises, remove the Leg Developer and Insert the
Arm Curl Stand into the opening on the Front Stabilizer.
DIAGRAM 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Right Upright Beam
Left Upright Beam 1
Backrest Adjustment Bar
Cross Brace
Q’ty
1
1
2
3
4
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
3
2
2
1
2
6
1
6
1
4
2
1
6
1
3
6
1
2
4
6
8
6
2
17
4
8
16
3
2
1
2
1
6
2
2
1
1
1
2
1
5
6
7
8
Backrest Support
Main Seat Support
Sliding Block
Front Stabilizer
Seat Bracket
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Left Bar Catch
Right Bar Catch
Headrest Bracket
Squat Bar Catch
Arm Curl Stand
Leg Developer
Leg Developer Holder
Headrest Board
Backrest Board
Seat Pad
Upright Beam Panel
Foam Roll Tube
2 ¾” x 2” End Cap
2 3/8” x 1 5/8” End Cap
Axle
Bushing
Bracket
Olympic Sleeve
Foam Roll
Olympic Spring Clip
2 3/8” Square End Cap
2” Square End Cap
1 ¾” Square End Cap
1” Square End Cap
∅ 1” End Cap
∅ 1” Round End Cap
Foam Roll End Cap
M10 x 4 ¾” Allen Bolt
M10 x 5/8” Allen Bolt
M6 x 1 3/8” Hex Bolt
M8 x 5/8” Allen Bolt
M10 x 3 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M8 x ¾” Allen Bolt
∅ ¾” Washer
∅ ½” Washer
∅ 5/8” Washer
M10 x Aircraft Nut
L-shaped Pin
∅ 2” x 1 ¾” Sleeve
∅ 3/8” Lock Knob
2 3/8” x 2” Sleeve
Arm Curl Pad
Panel Screw
Rubber Bumper
M10 x 1” Allen Bolt
Lock Pin
∅ ½” Lock Knob
2” Cone-shaped End Cap
Large Washer
M10 x 2 ½” Carriage Bolt
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal
use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty
extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing,
at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that specifically
set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential
damages or whatsoever natures.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may
not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899 during
our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|