NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
POWERHOUSE ELITE
SMITH MACHINE
PHE 9000
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PHE 9000
Retain This
Manual for
Reference
03-17-04
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE HARDEWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE HARDEWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE HARDEWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the Left & Right Base Frame (#1 & 2) by a Cross Brace (#3) in the mid-span.
Secure each end of the Cross Brace to each Base Frame with two M10 x 2 ¾” Carriage
Bolts (#77), one 4 ¾” x 2” Bracket (#32), two Ø ¾” Washers (#87), and two M10 Aircraft
Nuts (#88). NOTE: DO NOT tighten the Nuts and Bolts yet.
B.) Attach the Middle Vertical Frame (#4), the Rear Base Frame (#5) and the Foot Plate (#8)
to the Cross Brace (#3). Align the holes and secure them together with two M10 x 3”
Carriage Bolts (#76), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#88).
C.) Attach the top of each Weight Post Support (#20) to the Middle Vertical Beam (#4) from
each side. Attach the bottom of each Weight Post Support to the Cross Brace (#3).
D.) Secure the two Weight Post Supports (#20) to the Middle Vertical Frame (#4) with two
M10 x 2 ¾” Carriage Bolts (#77), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#88).
E.) Secure the bottom of each Weight Post Support to the Cross Brace with one M10 x 2 ¾”
Carriage Bolt (#77), Ø ¾” Washer (#87), and M10 Aircraft Nut (#88).
F.) Cover all ends on the Base Frame with five 2” End Caps (#58).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach a Front Vertical Frame (#6) to the Right Base Frame (#2). Secure it with
two M10 x 2 ¾” Carriage Bolts (#77), Ø ¾” Washers (#87), and M10 Aircraft Nuts
(#88). Do not tighten the Nuts and Bolts yet.
B.) Repeat Procedure A above to install the other side.
C.) Connect the two Front Vertical Frames (#6) with an Upper Frame (#10) on the top.
Secure each end with two M10 x 3 ½” Carriage Bolts (#75), Ø3/4” Washers (#87)
and M10 Aircraft Nuts (#88).
D.) Insert a Guide Rod (#7) into the “Ring” on the Right Base Frame (#2). Secure it
with a M8 x 3/8” Screw (#82).
E.) Slide a Lower Safety Catch (#96) onto the Guide Rod (#7).
F.) Slide an Ø 2 ½” Rubber Bumper (#57) onto the Rod.
G.)Slide a Safety Stop Frame (#9) onto the Rod.
H.) Attach the top of the Guide Rod (#7) to the “Ring” on the Upper Frame (#10) and
secure it with a M8 x 3/8” Screw (#82).
I.) Repeat the above Procedures D through H to install the other side.
J.) NOTE: Help of another person for this step is strongly recommended. Place the
Lifting Sleeve (#12) in between the two Safety Stop Frames (#9). Align the holes
and insert the Weight Bar (#11) into the Safety Stop Frame from one side and
through the Lifting Sleeve to the other Safety Stop Frame on the opposite side.
Secure the Weight Bar to each Safety Stop Frame with one M8 x 5/8” Allen Bolt
(#80).
K.) Turn the safety hook forward on the Lifting Sleeve (#12) into the selected holes on
the Front Vertical Frame to secure its position.
L.) Slide an Ø 3” Rubber Bumper (#55) onto each end of the Weight Bar. Attach the
Long Olympic Sleeve (#62) onto each end of the Weight Bar. Secure each Sleeve
to the Bar with one M8 x ½” Allen Bolt (#79).
M.)Attach a Spring Clip (#39) to each Olympic Sleeve.
N.) Insert Right & Left Short Safety Catches (#92 & #94) and the Right & Left Long
Safety Catches (#93 & #95) into the selected holes on the Front Vertical Frames.
O.)Securely tighten all Nuts and Bolts previously installed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Rear Vertical Frame (#14) to the Rear Base Frame (#5). Secure it with two
M10 x 2 ½” Allen Bolts (#69), four Ø ¾” Washers (#87), and two M10 Aircraft Nuts
(#88). Slide the Sliding Weight Post (#13) onto the Rear Vertical Frame (#14).
B.) Place the Lat Bar Frame Bracket (#15) onto the Rear & Middle Vertical Frame (#4 &
#14). Secure it to the Rear Vertical Frame (#14) with two M10 x ¾” Allen Bolts (#73)
and Ø ¾” Washers (#87). Secure it to the Middle Vertical Frame (#4) with one M10 x 2
3/8” Carriage Bolt (#78), Ø ¾” Washer (#87), and M10 Aircraft Nut (#88).
C.) Slide one Ø 3” Rubber Bumper (#55) and Olympic Sleeve (#63) onto each post on the
Sliding Weight Post. Secure each Sleeve with one M8 x ½” Allen Bolt (#79).
D.) Attach one Spring Clip (#39) to each Sleeve.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Left & Right Lat Bar Frames (#16 & #17) to the Upper Frame (#10). Align the
holes and secure each Lat Bar Frame to Upper Frame with one M10 x 5” Allen Bolt (#67),
two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88). Do not tighten the Nut and Bolt
yet.
B.) Attach the Left & Right Lat Bar Frames to the Lat Bar Frame Bracket (#15) from each
side. Secure them with two M10 x 5 3/8” Allen Bolts (#66), four Ø ¾” Washers (#87), and
two M10 Aircraft Nuts (#88).
C.) Secure each Lat Bar Frames to the front of the Bracket from each side with two M10 x 2
3/8” Carriage Bolts (#78), one 4 ¾” x 2 3/8” Bracket (#18), two Ø ¾” Washers (#87) and
two M10 Aircraft Nuts (#88).
D.) Securely tighten all nuts and bolts.
E.) Place a Pulley (#45) in the open slot on the Lat Bar Frame (#17). Secure the Pulley with
one M10 x 2 1/8” Allen Bolt (#70), two Short Pulley Bushings (#47), and one M10 Aircraft
Nut (#88). Repeat the same procedure to install the other side.
DIAGRAM 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Butterfly Base (#23) to the front of Middle Vertical Frame (#4). Attach the
Butterfly Pulley Bracket (#24) to the back of the Frame. Secure them with two M10 x 2
¾” Carriage Bolts (#77), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#88).
B.) Slide the Left Butterfly (#26) onto the pivot on the Butterfly Base. Secure it with one Lock
Ring (#64), M6 x 3/8” Allen Bolt (#84), and M6 Aircraft Nut (#90).
C.) Attach the Butterfly Arm Pad (#34) to the Left Butterfly. Secure it with two M8 x 2 ½” Allen
Bolts (#74) and Ø 5/8” Washers (#89).
D.) Repeat the Procedures B & C above to install the Right Butterfly (#27).
E.) Insert two Weight Posts (#21) into the holes on the Weight Post Supports (#20). Secure
each Post with one M10 x ¾” Allen Bolt (#73) and Ø ¾” Washer (#87). Slide one Olympic
Sleeve (#63) onto each Post. Secure each Sleeve with one M8 x ½” Allen Bolt (#79).
Attach a Spring Clip (#39) to each Sleeve.
DIAGRAM 5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Insert the 242” Upper Cable (#35) through the swivel pulley bracket pre-installed in the top
front of the Right Lat Bar Frame (#17).
B.) Install a Ball Stopper (#86) onto the end of the Cable. Attach a U-shaped Connector (#91) to
the end of the Cable.
C.) Attach a Short Chain (#40) in between the opening on the Connector and secure it with a M10
x 1 3/8” Allen Bolt (#72), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88).
D.) Draw the Cable over the Pulley and pull through the Cable sleeve on the Right Lat Bar Frame.
Draw the Cable along the Frame towards the back of the machine to the Pulley previously
installed. Draw the Cable around the Pulley then downward to an Angled Floating Pulley
Bracket (#28).
E.) Attach two Pulleys (#45) to the Bracket. Secure them with one M10 x 2 ¾” Allen Bolt (#68),
two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88).
F.) Draw the Cable around the back Pulley then upward to the open bracket underneath the Lat
Bar Frame Bracket (#15). Attach a Single Pulley Bracket (#98) to the bracket. Secure it with
one M10 x 1 3/8” Allen Bolt (#72), two Ø3/4” Washers (#87), and one M10 Aircraft Nut (#88).
Attach a Pulley to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71), two Ø ¾”
Washers (#87), and one M10 Aircraft Nut (#88).
G.)Draw the Cable around the Pulley then back down to the Angled Floating Pulley Bracket (#28)
again. Let the Bracket hanging for now.
H.) Draw the Cable around the front Pulley then upward towards the Pulley on the Left Lat Bar
Frame (#16).
I.) Draw the Cable over the Pulley then along the Left Lat Bar Frame towards the front of the
machine. Insert the Cable through the cable sleeve and over the pre-installed Pulley on the
front of the Left Lat Bar Frame.
J.) Repeat the Procedures B & C above to install a Ball Stopper, U-shaped Connector, and a
Short Chain.
K.) Connect the Lat Bar (#22) or Single Handles (#59) to the Short Chains using C-clips (#42).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 6
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach one end of the 76” Butterfly Cable (#36) to the clip on the Left Butterfly
(#26). Draw the Cable to the Butterfly Base Bracket (#24).
B.) Attach a Pulley (#45) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71),
one L-shaped Bracket (#25), two Ø ¾” Washers (#87), and one M10 Aircraft Nut
(#88).
C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single
Floating Pulley Bracket (#30). Secure it with one M10 x 1 ¾” Allen Bolt (#71), two
Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88). Let the Bracket hanging for
now.
D.) Pull the Cable upward to the right open bracket on the Butterfly Base Bracket (#24).
Repeat Procedure B above to install another Pulley.
E.) Draw the Cable around the Pulley then clip it to the Right Butterfly.
DIAGRAM 7
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8 & Cable Loop Diagram)
A.) Attach one end of the 140” High-Low Cable (#38) to the bracket on the Sliding Weight Post
(#13). Secure it with one M10 x 1 3/8” Allen Bolt (#72), two Ø ¾” Washers (#87), and one
M10 Aircraft Nut (#88).
B.) Draw the Cable upward to the open bracket underneath the Lat Bar Frame Bracket (#15).
Install another Pulley.
C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Double Floating
Pulley Bracket (#29). Install a Pulley to the upper bracket.
D.) Draw the Cable around the Pulley and upward to the Angled Floating Pulley Bracket (#28)
previously installed in Step-6. Install another Pulley.
E.) Draw the Cable around the Pulley then downward to the open bracket on the back of the
Middle Vertical Frame (#4). Install another Pulley.
F.) Draw the Cable around the Pulley then upward to the Single Floating Pulley Bracket (#30)
previously installed in Step-7. Secure the end of the Cable to the bracket with one M10 x 1”
Allen Bolt (#85), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9 & Cable Loop Diagram)
A.) Attach the 68” Lower Cable (#37) to the opening on the bottom of Middle Vertical
Frame (#4). Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt
(#69), two Long Pulley Bushings (#48), and one M10 Aircraft Nut (#88).
B.) Draw the Cable underneath the Pulley to the open bracket on the Rear Base Frame
(#5). Install a Pulley to the bracket.
C.) Draw the Cable around the Pulley then upward to the Double Floating Pulley
Bracket (#29) previously installed in Step-8. Install another Pulley.
D.) Draw the Cable around the Pulley then down to the open bracket on the Rear Base
Frame. Connect the end of the Cable to a Short Chain (#40) using a C-clip (#42).
Secure the Short Chain to the bracket with one M10 x 1 3/8” Allen Bolt (#72), two Ø
¾” Washers (#87), and one M10 Aircraft Nut (#88). Adjust the tension of the Cable
Loop System by adjusting the length of the Short Chain.
E.) Connect a Long Chain (#41) to the U-shaped Connector at the end of the Cable.
Connect the Shiver Bar (#31) to the Long Chain using a C-clip (#42).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
2
1
1
1
1
1
1
2
1
2
1
1
1
1
6
3
1
4
4
4
17
4
4
2
8
4
1
2
3
4
5
6
7
8
9
Left Base Frame
Right Base Frame
Cross Brace
Middle Vertical Frame
Rear Base Frame
Front Vertical Frame
Guide Rod
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
2” x 1 ¾” Sleeve
1” End Cap
2
2
8
1
4
1
2
5
2
5
9
2
4
2
2
2
2
1
3
2
12
5
4
6
4
2
14
5
6
2
1
4
8
2
1
2
83
55
7
2
2
Ø 1” Con-shaped End Cap
6” x 2” Rubber Bumper
Ø 3” Rubber Bumper
Ø 1 ½” Rubber Bumper
Ø 2 ½” Rubber Bumper
2” End Cap
Foot Plate
Safety Stop Frame
Single Handle
10 Upper Frame
11 Weight Bar
12 Lifting Sleeve
1 5/8” x 2 3/8” End Cap
2” Square End Cap
Long Olympic Sleeve
Olympic Sleeve
13 Sliding Weight Post
14 Rear Vertical Frame
15 Lat Bar Frame Bracket
16 Left Lat Bar Frame
17 Right Lat Bar Frame
18 4 ¾” x 2 3/8” Bracket
19 Swivel Pulley Bracket
20 Weight Post Support
21 Weight Post
22 Lat Bar
23 Butterfly Base
24 Butterfly Base Bracket
25 L-shaped Bracket
26 Left Butterfly
Lock Ring
M10 x 1 5/8” Allen Bolt
M10 x 5 3/8” Allen Bolt
M10 x 5” Allen Bolt
M10 x 2 ¾” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 2 1/8” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 1 3/8” Allen Bolt
M10 x ¾” Allen Bolt
M8 x 2 ½” Allen Bolt
M10 x 3 ½” Carriage Bolt
M10 x 3” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
M8 x ½” Allen Bolt
M8 x 5/8” Allen Bolt
M6 x 5/8” Screw
27 Right Butterfly
28 Angled Floating Pulley Bracket
29 Double Floating Pulley Bracket
30 Single Floating Pulley Bracket
31 Shiver Bar
32 4 ¾” x 2” Bracket
33 Backrest Board
34 Butterfly Arm Pad
35 242” Upper Cable
36 76” Butterfly Cable
37 68” Lower Cable
38 140” High Low Cable
39 Spring Clip
40 Short Chain
41 Long Chain
42 C-clip
43 Butterfly Bushing
44 1 ½” x 1” Sliding Sleeve
45 Pulley
M8 x 3/8” Screw
M6 x 3/8” Allen Bolt
M6 x 1 3/8” Allen Bolt
M10 x 1” Allen Bolt
Ball Stopper
Ø ¾” Washer
M10 Aircraft Nut
Ø 5/8” Washer
M6 Aircraft Nut
U-shaped Connector
Left Short Safety Catch
Left Long Safety Catch
Right Short Safety Catch
Right Long Safety Catch
Lower Safety Catch
Safety Hook
1
1
1
1
46 Handle Grip
2
2
1
47 Short Pulley Bushing
48 Long Pulley Bushing
49 Ø 1 3/8” Bushing
50 Ring Cap
Single Pulley Bracket
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI-PURPOSE BENCH HARDWARE PACK
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended this machine be assembled by two or
more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with
two M10 x ¾” Allen Bolts (#30) and ∅ ¾” Washers (#36). Attach a Lock Knob (#18) to the
Nut underneath the Main Frame (#1).
B.) Slide the Sliding Block (#8) onto the Incline Adjustment Bar (#9). Align the hole then
secure it with a Lock Knob (#18) to hold the Sliding Block in position.
C.) Attach the Incline Adjustment Bar (#9) to the brackets on the Main Frame (#1). Secure
each end with one M10 x 2 ½” Carriage Bolt (#29), ∅ ¾” Washer (#36), and M10 Aircraft
Nut (#38).
D.) Cover the Stabilizer ends with four 2” Stabilizer End Caps (#28).
DIAGRAM 1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach four Bushings (#21) to a Seat Support Frame (#6).
B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and
secure them with one M10 x 1 ¾” Allen Bolt (#31) and ∅ ¾” Washer (#36). Repeat the same
procedure to install the other side.
C.) Attach two Bushings to the pivot on the Sliding Block (#8). Attach two Bushings to each
Backrest Supports (#7). Align the holes and secure them with one M10 x 6 ¾” Allen Bolt (#32),
two ∅ ¾” Washers (#36), and one M10 Aircraft Nut (#38). Do not over tighten the nut and bolt.
The Supports need to swivel on the Bolt.
D.) Attach two Bushings to the pivot on the Main Frame (#1). Loosen and pull the Lock Knob on
the Sliding Block (#8). The Sliding Block needs to be able to slide on the Chromed Incline
Adjustment Bar (#9). Align the two Seat Support Frames (#6) to both ends of the pivot on Main
Frame. Secure them with one M10 x 8 ¼” Allen Bolt (#33), two ∅ ¾” Washers (#36), and one
M10 Aircraft Nut (#38).
E.) Use the Lock Knob on the Sliding Block (#8) to adjust and secure the backrest incline position.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Place the Backrest Board (#12) onto the Backrest Supports (#7). Secure it
with four M8 x 2” Allen Bolts (#34) and ∅ 5/8” Washers (#37).
B.) Place the Seat Pad (#11) onto the Seat Support Frames (#6). Secure it with
four M8 x 2” Allen Bolts (#34) and Ø 5/8” Washers (#37).
DIAGRAM 3
23
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with
an Axle (#14), two M10 x ¾” Allen Bolts (#30), and two ∅ ¾” Washers (#36).
B.) Insert one Foam Tube (#10) halfway through the hole on the Main Frame. Insert two
Foam Tubes halfway through the holes on the Leg Developer (#5). Push six Foam Rolls
(#19) onto the Tubes from both ends. Plug six Foam Roll End Caps (#20) into the Tubes.
C.) Slide the Olympic Sleeve (#16) onto the weight post on the Leg Developer and secure it
with one M8 x ½” Allen Bolt (#39). Attach a Spring Clip (#17) to the Sleeve.
D.) Attach the Bar Holder (#40) to the Leg Developer and secure it with a L-shaped Lock Pin
(#41). Remove the Pin and Bar Holder when doing Leg Exercise.
DIAGRAM 4
24
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Arm Curl Pad (#13) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8”
Allen Bolts (#35) and two ∅ 5/8” Washers (#37). Insert the Arm Curl Stand into the front
opening on the Main Frame (#1). Use the Lock Knob to hold the desired Arm Curl height.
B.) The Leg Developer can be locked when doing Sit Up exercises. Simply pull the U-shaped
Pin out and drop into the hole on the Leg Developer. Remove the Pin when doing Leg
Developer exercises.
DIAGRAM 5
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI-PURPOSE BENCH
PARTS LIST
KEY NO.
1
DESCRIPTION
Main Frame
Q’ty
1
2
3
4
5
6
7
8
Front Stabilizer
Rear Stabilizer
Arm Curl Stand
Leg Developer
Seat Support Frame
Backrest Support
Sliding Block
1
1
1
1
2
2
1
9
Incline Adjustment Bar
Foam Tube
1
3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Seat Pad
Backrest Board
Arm Curl Pad
1
1
1
1
2
1
1
2
6
6
16
1
1
1
2
12
3
4
2
6
2
1
1
8
2
14
14
4
1
1
1
1
2
2
Axle
Ø 2 3/8” Bushing
Olympic Sleeve
Spring Clip
Lock Knob
Foam Roll
Foam Roll End Cap
Bushing
1 5/8” x 3 1/8” End Cap
Ø 1” Cone-shaped End Cap
Ø 1” End Cap
1 5/8” x 2 3/8” End Cap
1 5/8” x ¾” End Cap
2” Sleeve
2” Stabilizer End Cap
M10 x 2 ½” Carriage Bolt
M10 x ¾” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 6 ¾” Allen Bolt
M10 x 8 ¼” Allen Bolt
M8 x 2” Allen Bolt
M8 x 5/8” Allen Bolt
Ø ¾” Washer
Ø 5/8” Washer
M10 Aircraft Nut
M8 x ½” Allen Bolt
Bar Holder
L-shaped Lock Pin
U-shaped Lock Pin
Roller Wheel
M8 x 1 5/8” Allen Bolt
M8 Aircraft Nut
Spring
2
1
1
1
Spring Spacer
M6 x 5/8” Allen Bolt
27
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to
replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused by
or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an
IMPEX authorized service center or for products used for commercial or rental purposes. No other warranty
beyond that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.Model
2.Description of Parts
3.Part Number
4.Date of Purchase
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|