NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
POWERHOUSE CLUB
PHC 750
Warranty
Ordering Parts
Model
PHC 750
Retain This
Manual for
Reference
09-26-01
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions
apply whenever you operate a piece of exercise equipment. Be sure to read the
entire manual before you assemble or operate your machine. In particular, note the
following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended this machine to be assembled by two or
more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span.
Align the holes and secure them with one Bracket (#20), two M10 x 3 1/8”
Carriage Bolts (#38), two ∅ ¾” Washers (#45), and two M10 Aircraft Nuts (#44)
on each end of the Cross Brace.
B.) Place Backrest Adjustment Bar (#4) between the two Upright Beams on the
selected bar holder to obtain desired incline of Backrest.
C.) Insert two Crutches (#7) into the top openings on the Upright Beams. Secure
them with two Lock Knobs (#23) through selected holes to obtain desired height
of the Supports.
D.) Slide a Rubber Bumper (#22) onto a Weight Post (#8). Insert the Post into the
hole on the back of the Upright Beam (#1). Secure it with one M10 x 1” Allen
Bolt (#37) and ∅ ¾” Washer (#45). Repeat the same step to install the other
side.
DIAGRAM 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Leg Developer Holder (#5) to the Front Stabilizer (#6). Secure it with
three M10 x 5/8” Allen Bolts (#43) and ∅ ¾” Washers (#45).
B.) Attach the Leg Developer Holder (#5) to the front of Main Seat Support (#3).
Secure it with one M10 x 2 ½” Carriage Bolt (#56), two M10 x 2 ¾” Carriage Bolts
(#39), three ∅ ¾” Washers (#45), and three M10 Aircraft Nuts (#44).
C.) Attach the back of Main Seat Support (#3) to the Cross Brace (#2). Secure it with
one Bracket (#20), two M10 x 2 ¾” Carriage Bolts (#39), ∅ ¾” Washers (#45),
and M10 Aircraft Nuts (#44).
D.) Insert one Lock Knob (#23) into the hole on the back of Leg Developer Holder.
DIAGRAM 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the hole-side of the Seat Bracket (#11) to the Pivot on the Main Seat Support
(#3). Push two Bushings (#36) into the holes on the Pivot.
B.) Attach the Backrest Supports (#10) to the Pivot. Secure it with one M10 x 7 ¼” Hex
Bolt (#41), two ∅ ¾” Washers (#45), and one M10 Aircraft Nut (#44). DO NOT
tighten the nut and bolt yet. Place the Backrest Incline Support (#9) in between the
two Backrest Supports (#10). Securely tighten the Nut (#44) and Bolt (#41).
C.) Place Backrest Board (#18) onto the Backrest Supports (#10). Secure it with four M6
x 1 3/8” Hex Bolts (#40) and ∅ ½” Washers (#47).
D.) Place the Seat Pad (#17) onto the Seat Bracket (#11). Secure the two back holes on
the Seat with two M8 x 5/8” Hex Bolts (#42) and ∅ 5/8” Washers (#46). Secure the
two front holes on the Seat with a Seat Incline Adjustment (#12), two M8 x 5/8” Hex
Bolts (#42) and two ∅ 5/8” Washers (#46). Insert a 4” L-shaped Pin (#25) into the
selected hole on the Seat Incline Adjustment to hold the desired seat incline. When
using the Uprights to do squat exercises, lift the Backrest Board to vertical position
and secure it with a 4” L-shaped Pin (#25). NOTE: The vertical support is not
designed to sustain any weight. The only purpose of it is to get the Backrest Board
out of the user’s way when doing squat.
DIAGRAM 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#14) to the bracket on top of the Leg Developer Holder (#5).
Secure it with an Axle (#48), two ∅ ¾” Washers (#45), and two M10 x 5/8” Allen Bolts
(#43). Slide the Olympic Sleeve (#55) onto the post on the Leg Developer. Attach a
Spring Clip (#21) to the Sleeve. Note: When using the decline position to do Ab
exercises, place at least 30lbs of weights on the Sleeve to hold down the Leg Developer.
B.) Insert one Foam Roll Tube (#15) halfway through the hole on the Leg Developer Holder.
Insert two Foam Roll Tubes (#15) halfway through the holes on the Leg Developer (#14).
Push six Foam Rolls (#16) onto the Tubes from both sides. Plug six Foam Roll End Caps
(#33) to the ends.
C.) Attach the Arm Curl Pad (#19) to the Arm Curl Stand (#13). Secure it with two M8 x 5/8”
Hex Bolts (#42) and ∅ 5/8” Washers (#46). Insert the Arm Curl Stand into the top opening
in front of the Seat.
D.) Attach the Curl Bar Holder (#49) to the Leg Developer (#14). Align the holes and secure it
with 2 ¾” L-shaped Pin (#53). Attach a ∅ 3/8” Spring Clip (#54) to the Pin. Attach two
Spring Clips (#21) to both ends of Curl Bar (#50). Place the Curl Bar on the Curl Bar
Holder for Arm Curl exercises.
DIAGRAM 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Upright Beam
Cross Brace
Main Seat Support
Backrest Adjustment Bar
Leg Developer Holder
Front Stabilizer
Q’ty
2
1
1
1
1
1
2
2
1
2
1
1
1
1
3
6
1
1
1
3
3
2
3
2
2
5
1
2
4
3
2
2
6
2
1
2
4
4
4
4
1
6
5
10
20
6
4
1
1
1
2
2
1
1
1
1
1
2
3
4
5
6
7
8
Crutch
Weight Post
9
Backrest Incline Support
Backrest Support
Seat Bracket
Seat Incline Adjustment
Arm Curl Stand
Leg Developer
Foam Roll Tube
Foam Roll
Seat Pad
Backrest Board
Arm Curl Pad
Bracket
Spring Clip
Rubber Bumper
Lock Knob
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
3 1/8” Sleeve
4” L-shaped Pin
∅ 1” Cone-shaped End Cap
∅ 1” End Cap
∅1 1/8” End Cap
2 3/8” Square End Cap
1” Square End Cap
2” Square End Cap
2 3/8” x 1 5/8” End Cap
Foam Roll End Cap
∅ 2 3/8” Bushing
2” Sleeve
Bushing
M10 x 1” Allen Bolt
M10 x 3 1/8” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M6 x 1 3/8” Hex Bolt
M10 x 7 ¼” Hex Bolt
M8 x 5/8” Hex Bolt
M10 x 5/8” Allen Bolt
M10 Aircraft Nut
∅ ¾” Washer
∅ 5/8” Washer
∅ ½” Washer
Axle
Curl Bar Holder
Curl Bar
Curl Bar Sleeve
∅ 2” Cone-shaped End Cap
2 ¾” L-shaped Pin
∅ 3/8” Spring Clip
Olympic Sleeve
M10 x 2 ½” Carriage Bolt
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused
by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not
provided by an IMPEX authorized service center or for products used for commercial or rental
purposes. No other warranty beyond that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic
loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal,
installation or other consequential damages or whatsoever natures. Some states do not allow the
exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may
not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties
of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to
state. Register on-line at www.impex-fitness.com
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-
8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard
time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|