NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
MARCY OLYMPIC BENCH
MWB-855
Warranty
Ordering Parts
Model
MWB 855
Retain This
Manual for
Reference
07-25-03
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Align the
holes and secure each end of the Cross Brace with two M10 x 3 1/8” Carriage Bolts
(#44), one 4 ¾” x 2” Bracket (#21), two ∅ ¾” Washers (#52), and two M10 Aircraft
Nuts (#51).
B.) Insert two Crutches (#10) into the top openings on the Upright Beams. Secure them
with two Lock Knobs (#38) through selected holes to obtain desired height of the
Supports.
C.) Place the Backrest Adjustment Bar (#8) onto the selected slot on Upright Beams to
hold the desired incline.
D.) Insert one Weight Post (#11) to each Upright Beam. Secure it with one M10 x 1” Allen
Bolt (#46) and ∅ ¾” Washer (#52). Attach one Olympic Sleeve (#36) to each Post.
Secure the Sleeve to the post with one M8 x ½” Allen Screw (#55). Attach a Spring
Clip (#25) to each Sleeve.
DIAGRAM 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Leg Developer Holder (#5) to the Front Stabilizer (#4). Secure it with three
M10 x 5/8” Allen Bolts (#47) and ∅ ¾” Washers (#52).
B.) Attach the Main Seat Support (#3) to the Leg Developer Holder (#5). Secure it with
three M10 x 2 ¾” Carriage Bolts (#45), M10 Aircraft Nuts (#51) and ∅ ¾” Washers
(#52).
C.) Attach the Main Seat Support (#3) to the Cross Brace (#2). Secure it with two M10 x 2
¾” Carriage Bolts (#45), one 4 ¾” x 2” Bracket (#21), two ∅ ¾” Washers (#52), and two
M10 Aircraft Nuts (#51).
DIAGRAM 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Seat Bracket (#13) to the pivot on the Main Seat Support (#3). Push two
Bushings (#22) through the holes on the Seat Bracket into both ends of the pivot.
B.) Attach Backrest Incline Support (#7) in between the two Backrest Supports (#6) and
insert both ends into the side-holes on the Backrest Supports. Attach the Backrest
Supports to the Bushings. Secure it with one M10 x 7 ¼” Allen Bolt (#43), two ∅ ¾”
Washers (#52), and one M10 Aircraft Nut (#51).
C.) Place the other end of Backrest Support rest against the Backrest Adjustment Bar.
D.) When using the Squat exercise, lift up the Backrest Board to a near vertical position
and secure the Backrest Incline Support with a 4” L-shaped Pin (#23) into the open
slot on the Main Seat Support. Please note the only purpose of the Backrest Incline
Support and Pin is to get the Backrest Board out of the way while doing squat exercise
from the rear of the machine. They are not designed to support any weight or perform
any exercise.
E.) Place the Backrest Board (#17) onto Backrest Supports (#6). Secure it with four M6 x 1
3/8” Hex Bolts (#49) and Ø ½” Washers (#54).
F.) Attach the Seat Incline Adjustment (#20) to the Seat Bracket from bottom. Place the
Seat (#18) onto the Seat Bracket (#13). Secure the Seat with four M6 x 5/8” Hex Bolts
(#50) and ∅ ½” Washers (#54). Insert a 4” L-shaped Pin (#23) into selected hole on
Seat Incline Adjustment to obtain the desired height of Seat Pad.
G.) Attach the Arm Curl Pad (#19) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8”
Allen Bolts (#48) and Ø 5/8” Washers (#53). Insert the Arm Curl Stand into the top
opening on the Leg Developer Holder. Secure it with a Lock Knob (#38).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#14) to the Leg Developer Holder (#5). Secure it with an
Axle (#39), two M10 x 5/8” Allen Bolts (#47), and two Ø ¾” Washers (#52).
B.) Insert one Foam Tube (#12) halfway through the hole on the Leg Developer Holder.
Insert two Foam Tubes halfway through the holes on the Leg Developer.
C.) Push six Foam Rolls (#37) onto the Tubes from both ends. Plug six Foam Roll End
Caps (#32) into the ends.
D.) Attach the Curl Bar Handle Support (#15) to the bracket on the Leg Developer and
secure it with a 3” L-shaped Pin (#24). When using the Leg Developer, remove the
Pin, Curl Bar, and the Arm Curl Stand.
E.) Attach an Olympic Sleeve (#36) onto the weight post on the Leg Developer. Secure it
with a M8 x ½” Allen Screw (#55). Attach a Spring Clip (#25) to the Sleeve.
DIAGRAM 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Upright Beam
Cross Brace
Main Seat Support
Front Stabilizer
Leg Developer Holder
Backrest Support
Backrest Incline Support
Backrest Adjustment Bar
Arm Curl Stand
Crutch
Weight Post
Foam Tube
Seat Bracket
2
1
1
1
1
2
1
1
1
2
2
3
1
1
1
1
1
1
1
1
3
2
2
1
3
2
1
4
2
2
2
6
1
3
2
3
6
3
1
2
2
2
1
4
5
2
5
2
4
4
10
18
2
8
3
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Leg Developer
Curl Bar Handle Support
Curl Bar Handle
Backrest Board
Seat
Arm Curl Pad
Seat Incline Adjustment
4 ¾” x 2” Bracket
Bushing
4” L-shaped Pin
3” L-shaped pin
Spring Clip
2 3/8” x 2” Crutch Sleeve
2” x 1 ¾” Sleeve
2 3/8” Square End Cap
2” Square End Cap
1 5/8” x 2 3/8” End Cap
∅ 1” Cone-shaped End Cap
Foam Roll End Cap
∅ 1” End Cap
1” Square End Cap
∅ 1 1/8” x 1” End Cap
Olympic Sleeve
Foam Roll
Lock Knob
Axle
∅ 2 3/8” Axle Bushing
∅ 1 3/8” Spacer
Curl Bar Handle Grip
M10 x 7 ¼” Allen Bolt
M10 x 3 1/8” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 1” Allen Bolt
M10 x 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
M6 x 1 3/8” Hex Bolt
M6 x 5/8” Hex Bolt
M10 Aircraft Nut
∅ ¾” Washer
∅ 5/8” Washer
∅ ½” Washer
M8 x ½” Allen Screw
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|