NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY WEIGHT BENCH
MWB -558
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MWB 558
Retain This
Manual for
Reference
09-12-03
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Attach two Ø 2 3/8” End Caps (#20) to the bottom of two Upright Beams (#1 & #2).
B.) Connect the Left & Right Upright Beams (#1) & (#2) by the Cross Brace (#3) in the mid-span.
Align the holes then secure each end of Cross Brace with one Bent Bracket (#13), two M10 x
3 1/8” Carriage Bolts (#28), two ∅ ¾” Washers (#29), and two M10 Aircraft Nuts (#30).
C.) Insert two Bar Holders (#4) into the top opening on the Upright Beams. Secure them with two
M16 Lock Knobs (#18) through selected hole to obtain desired height of the Holders.
D.) Place the Backrest Adjustment Bar (#5) in between the two Upright Beams.
DIAGRAM 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach a Ø 2 3/8” End Cap (#20) to the bottom of the Leg Developer Holder (#8).
B.) Attach the Leg Developer Holder to the front of the Main Seat Support (#6). Secure it with
three M8 x 5/8” Allen Bolts (#38) and Ø 5/8” Washers (#33).
C.) Attach the top of Diagonal Support (#7) to the Main Seat Support (#6). Secure it with one M8
x 2 1/8” Allen Bolt (#32), two Ø 5/8” Washers (#33) and one M8 Aircraft Nut (#34). Attach the
bottom of the Diagonal Support to the Leg Developer Holder. Secure it with one M8 x 5/8”
Allen Bolt (#38) and Ø 5/8” Washer (#33).
D.) Attach the Rear of the Main Seat Support (#6) to the Cross Brace (#3). Secure it with one
Flat Bracket (#14), two M10 x 2 ½” Carriage Bolts (#31), two ∅ ¾” Washers (#29), and two
M10 Aircraft Nuts (#30).
DIAGRAM 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#9) to the Leg Developer Holder (#8). Secure it with one M8 x 3
1/8” Allen Bolt (#37), two ∅ 5/8” Washers (#33), and one M8 Aircraft Nut (#34).
B.) Insert one Foam Tube (#10) halfway through the hole on the Leg Developer Holder and two
Foam Tubes halfway through the two holes on the Leg Developer (#9).
C.) Push six Foam Rolls (#21) onto the Tubes from both ends. Attach a Spring Clip (#27) onto
the weight post on the Leg Developer.
DIAGRAM 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the hole-side of the Backrest Supports (#12) to the pivot on the Main Seat Support
(#6). Place the other end of Backrest Supports rest against the Backrest Adjustment Bar
(#5). Place the Backrest Board (#15) onto the Backrest Supports. Secure it with four M6 x 1
3/8” Hex Bolts (#35) and ∅ ½” Washers (#36).
B.) Place the Seat (#16) onto the Main Seat Support (#6). Secure it with four M6 x 1 3/8” Hex
Bolts (#35) and Ø ½” Washers (#36).
DIAGRAM 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Arm Curl Pad (#17) to the Arm Curl Stand (#11). Secure it with two M8 x 5/8”
Allen Bolts (#38) and Ø 5/8” Washers (#33).
B.) Insert the Arm Curl Stand into the opening on top of the Leg Developer Holder. Use a
M10 Lock Knob (#22) to secure the desired height.
DIAGRAM 5
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Left Upright Beam
Right Upright Beam
Cross Brace
1
1
1
2
1
1
1
1
1
3
1
2
2
1
1
1
1
3
3
3
6
6
2
6
2
2
3
4
6
6
2
1
10
2
8
8
1
6
1
Bar Holder
Backrest Adjustment Bar
Main Seat Support
Diagonal Support
Leg Developer Holder
Leg Developer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Foam Tube
Arm Curl Stand
Backrest Support
Bent Bracket
Flat Bracket
Backrest Board
Seat
Arm Curl Pad
M16 Lock Knob
Ø 2 3/8” Sleeve
Ø 2 3/8” End Cap
Foam Roll
Ø 1” End Cap
Bushing
Ø 1” Cone-shaped End Cap
Ø 2” End Cap
1” Square End Cap
Spring Clip
M10 x 3 1/8” Carriage Bolt
Ø ¾” Washer
M10 Aircraft Nut
M10 x 2 ½” Carriage Bolt
M8 x 2 1/8” Allen bolt
Ø 5/8” Washer
M8 Aircraft Nut
M6 x 1 3/8” Hex Bolt
Ø ½” Washer
M8 x 3 1/8” Allen Bolt
M8 x 5/8” Allen Bolt
Weight Bar
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to
replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused by
or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an
IMPEX authorized service center or for products used for commercial or rental purposes. No other warranty
beyond that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1. Model
2. Description of Parts
3. Part Number
4. Date of Purchase
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|