NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY® PLATINUM
CORNER GYM
MP-4500
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MP-4500
Retain This
Manual for
Reference
10-25-06
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply whenever
you operate a piece of exercise equipment. Be sure to read the entire manual before you
assemble or operate your machine. In particular, note the following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the same station.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING:
BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF
35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS
BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC. ASSUMES NO
RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR
THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Left Base Frame and Left Upper Frame. If the labels
are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in
location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended two or people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Place the Right Base Frame (#31) on a flat surface. Make sure there is enough space
around to assemble the machine.
B.) Insert four Guide Rods (#16) into the holes on the Right Base Frame. Secure each
Guide Rod from bottom with a M10 x ¾” Allen Bolt (#95) and Ø ¾” Washer (#100).
C.) Attach four Ø 2 3/8” x 1” Rubber Bumpers (#52) to top of the Guide Rods then slid down
to the stopper on the Guide Rods.
D.) Attach the Right Vertical Frame (#4) onto the Right Base Frame. Secure it with two M10
x 2 ¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100),
and two M10 Aircraft Nuts (#102).
E.) Attach the Butterfly Base (#13) to the Right Base Frame (#31). Attach the Front Base
Frame (#12) to the Butterfly Base (#13) from the front. Align the holes and secure them
together with two M10 x 3 ¾” Carriage Bolts (#97) from side, two M10 x 2 ¾” Carriage
Bolts (#98) from the bottom, four Ø ¾” Washers (#100), and four M10 Aircraft Nuts
(#102).
F.) Slide fourteen Weight Plates (#80) onto the rear set of Guide Rods. Make sure the
groove on the plates all face toward the back of the machine.
G.) Insert a Selector Rod (#28) into the center holes. Slide a Selector Stem (#81) onto the
two Guide Rods.
H.) Insert a Weight Selector Pin (#74) to select the number of weight plates. Each Weight
Plate weights approximately 10 lbs. Please refer to the Weight Resistance Chart in page
35.
I.) Repeat procedures F, G and H above to install the other fourteen Weight Plates onto the
front two Guide Rods.
J.) Attach the Foot Plate (#17) to the Front Base Frame (#12). Secure it with the Foot Plate
Axle (#18).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Right Upper Frame (#1) onto the Right Vertical Frame (#4). Secure it with two M10 x 2
¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and two M10
Aircraft Nuts (#102). Do not tighten the Nuts and Bolts yet.
B.) Attach the Right Upper Frame to the four Guide Rods (#16). Secure it to each Guide Rod with
one M10 x ¾” Allen Bolt (#95) and Ø ¾” Washer (#100).
C.) Securely tighten the Nuts and Bolts previously installed.
D.) Attach the Right Seat Support (#7) to the Right Vertical Frame (#4). Secure it with two M10 x 2 ¾”
Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and two M10
Aircraft Nuts (#102).
E.) Attach the Leg Developer (#8) to the open bracket on the Right Seat Support. Secure it with one
Axle (#15), two M10 x ¾” Allen Bolts (#95), and two Ø ¾” Washers (#100).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Front Press Base (#2) to the Right Upper Frame (#1). Secure it with one 6 ¾”
Front Press Base Axle (#29), two Ø 1 ¼” x Ø 3/8” Washers (#70), and two M10 Aircraft
Nuts (#102). Do not over tighten the Nuts; make sure the Base is able to swivel.
B.) Attach the Front Press (#3) to the Front Press Base (#2). Secure it with one 7 5/8” Front
Press Axle (#30), two Ø 1 ¼” x Ø 3/8” Washers (#70), and two M10 Aircraft Nuts (#102).
Do not over tighten the Nuts; make sure the Press Arm is able to swivel.
C.) Thread the Short T-shaped Lock Pin (#78) into the tube on the Front Press to obtain the
desired Front Press position.
D.) Attach the Backrest Board (#43) to the Backrest Support Frame (#5). Secure it with two M8
x 1 5/8” Allen Bolts (#85) and Ø 5/8” Washers (#101).
E.) Attach the Backrest Support Frame (#5) to the Right Vertical Frame (#4). Secure it with one
M10 x 4 3/8” Allen Bolt (#89), two Ø ¾” Washers (#100), and one M10 Aircraft Nut (#102).
F.) Thread a Long T-shaped Lock Pin (#77) into the hole on the Right Vertical Frame to obtain
the desired Backrest position.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Seat Pad (#42) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen
Bolts (#85) and Ø 5/8” Washers (#101).
B.) Insert the Seat Post into the opening on the Right Seat Support (#7). Secure it with a
Lock Knob (#73) to lock the Seat Post at desired height.
C.) Insert the Foam Tube (#23) halfway through the hole on the Leg Developer (#8). Push
two Foam Rolls (#58) onto the Tube from both ends. Plug a Foam Roll End Cap (#59)
into each end of the Tube.
DIAGRAM 4
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Right Butterfly (#10) onto the axle on the Butterfly Base (#13).
B.) Insert the Butterfly Handle (#9) into the pivot on the Right Butterfly. Secure it with one M10 x
¾” Allen Bolt (#95) and Ø 1 ¼” x Ø 3/8” Washer (#70) from the bottom. Do not over tighten
the Bolt; make sure the handle is able to swivel.
C.) Repeat Procedure A & B above to install the Left Butterfly (#11).
DIAGRAM 5
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6)
A.) Do not tighten all Nuts and Bolts in this Step until instructed to do so.
B.) Attach the Left Vertical Frame (#33) onto the Left Base Frame (#32). Secure it with two M10
x 2 ¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and
two M10 Aircraft Nuts (#102).
C.) Attach the Left Base Frame (#32) to the Right Base Frame (#31). Secure it with two M10 x 3
½” Carriage Bolts (#99), one 4 ½” x 2” Bracket (#26), two Ø ¾” Washers (#100), and two
M10 Aircraft Nuts (#102).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7)
A.) Attach the Left Upper Frame (#34) onto the Left Vertical Frame (33). Secure it with two M10
x 2 ¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and
two M10 Aircraft Nuts (#102). Do not tighten the Nuts and Bolts yet.
B.) Attach the rear of Left Upper Frame to the Right Upper Frame (#1). Secure it with two M10 x
3 ½” Carriage Bolts (#99), one 4 ½” x 2” Bracket (#26), two Ø ¾” Washers (#100), and two
M10 Aircraft Nuts (#102).
C.) Securely tighten all Nuts and Bolts previously installed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8)
A.) Attach the Left Seat Support (#35) onto the Left Base Frame (#32). Secure it with one M10 x 3 ½”
Carriage Bolt (#99), Ø ¾” Washer (#100), and M10 Aircraft Nut (#102).
B.) Attach the Left Seat Support to the Left Vertical Frame (#33). Secure it with two M10 x 2 ¾”
Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and two M10
Aircraft Nuts (#102).
C.) Attach the Right & Left Handle (#37& 38) to the Left Seat Support from each side. Secure them
together with two M10 x 2 ¾” Carriage Bolts (#98), Ø ¾” Washers (#100), and M10 Aircraft Nuts
(#102).
D.) Attach a Seat Pad (#42) to the Left Seat Support. Secure it with two M8 x 2 ½” Allen Bolts (#86)
and Ø 5/8” Washers (#101).
E.) Attach a Backrest Board (#43) to the Left Vertical Frame. Secure it with two M8 x 2 ½” Allen Bolts
(#86) and Ø 5/8” Washers (#101).
DIAGRAM 8
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) Attach the Leg Press Frame (#36) to the bracket on the Left Base Frame (#32). Secure it with an
Axle (#15), two M10 x ¾” Allen Bolts (#95), and two Ø ¾” Washers (#100).
B.) Insert the Leg Press Adjustment Frame (#40) into the Leg Press Frame. Thread a Lock Knob (#73)
into the Leg Press Frame to obtain the desired leg press exercise position.
C.) Attach the Leg Press Plate (#39) to the Leg Press Adjustment Frame. Secure it with one M10 x 2
5/8” Allen Bolt (#92), two Ø ¾” Washers (#100), and one M10 Aircraft Nut (#102).
DIAGRAM 9
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 10 (See Diagram 10 & Front Press Cable Loop Diagram)
A.) Attach one end of the 140” Front Press Cable (#48) to the bracket underneath the Right
Upper Frame (#1). Secure it with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers
(#100), and one M10 Aircraft Nut (#102).
B.) Draw the Cable to the opening on the Front Press Base (#2). Attach a Pulley (#67) to
the upper opening. Secure it with one M10 x 6 ¼” Allen Bolt (#88), two Ø ¾” Washers
(#100), and one M10 Aircraft Nut (#102).
C.) Draw the Cable around the Pulley to the opening on the Right Vertical Frame (#4).
Install a Pulley to the upper opening with M10 x 3 ½” Allen Bolt (#90), two Ø 7/8” x 1”
Pulley Bushings (#53), and one M10 Aircraft Nut (#102).
D.) Draw the Cable around the Pulley and back to the lower opening on the Front Press
Base. Repeat Procedure B above to install a Pulley.
E.) Draw the Cable around the Pulley to the lower opening on the Right Vertical Frame.
Repeat Procedure C above to install another Pulley.
F.) Draw the Cable underneath the Pulley then upward to the opening on the Right Upper
Frame (#1). Repeat Procedure C above to install a Pulley.
G.)Draw the Cable around the Pulley then downward. Attach a Pulley to the top hole on the
two Double Floating Pulley Brackets (#22).
H.) Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾” Washers (#100), and
one M10 Aircraft Nut (#102). Draw the Cable around the Pulley and upward. Let the
Brackets hanging for now.
I.) Draw the Cable upward to the open bracket underneath the Right Upper Frame. Repeat
Procedure H above to install a Pulley.
J.) Draw the Cable around the Pulley then downward in between the two Guide Rods to the
Selector Rod (#28). Fully thread the Bolt on the end of the Cable into the Selector Rod.
Use the Nut at the end of the Cable to tighten the Bolt.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 10
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Press Cable Loop Diagram
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 11 (See Diagram 11 & Lower Cable Loop Diagram)
A.) Attach the 157” Lower Cable (#46) to the lower opening on the Leg Developer (#8).
Attach a Pulley (#67) to the opening. Secure it with one M10 x 2 5/8” Allen Bolt (#92),
two Ø 7/8” x 5/8” Pulley Bushings (#56), and one M10 Aircraft Nut (#102).
B.) Draw the Cable underneath the Pulley to the open bracket on the Right Base Frame
(#31). Attach a Pulley to the bracket and secure it with one M10 x 1 ¾” Allen Bolt (#93),
two Ø ¾” Washes (#100), and one M10 Aircraft Nut (#102).
C.) Draw the Cable underneath the Pulley through the bottom opening on the Right Vertical
Frame (#4) to another open bracket on the Right Base Frame. Repeat Procedure B
above to install a Pulley.
D.) Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket
(#22) previously installed in Step-10. Install a Pulley to the Brackets on selected hole.
After completing Step-12, come back to this step and check the tension of the Cable
loop system. If the cables are too loose, move up the Pulley on the Bracket. Move
down the Pulley if the Cables are too tight.
E.) Draw the Cable around the Pulley then downward. Install a Pulley to an Angled Double
Floating Pulley Bracket (#27).
F.) Draw the Cable around the Pulley then upward to the bracket on the back of Right
Vertical Frame. Secure the Cable to the bracket with one M10 x 1” Allen Bolt (#94), two
Ø ¾” Washers (#100), and one M10 Aircraft Nut (#102). Let the Bracket hanging for
now.
G.)Connect the Shiver Bar (#19) to the Cable with a Chain (#75) and two Hooks (#76).
Replace Shiver Bar with Single Handle (#83) or Ankle Strap (#84) for various exercises.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 11
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Lower Cable Loop Diagram
23
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 12 (See Diagram 12 & Butterfly Cable Loop Diagram)
A.) Clip one end of the 96” Butterfly Cable (#45) to the open slot on the Right Butterfly (#10).
B.) Draw the Cable to the open bracket on the right side of the Right Vertical Frame (#4).
Attach a Small Pulley (#68) to the bracket.
C.) Secure it with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾” Washers (#100), and one M10
Aircraft Nut (#102).
D.) Draw the Cable around the Small Pulley to the right open bracket on the Right Base
Frame (#31). Repeat Procedure C above to install a Pulley.
E.) Draw the Cable around the Pulley then upward to the Angled Double Floating Pulley
Bracket (#27) previously installed in Step –11. Repeat Procedure C above to install a
Pulley.
F.) Draw the Cable around the Pulley then downward to the left open bracket on the Right
Base Frame. Repeat Procedure C above to install another Pulley.
G.)Draw the Cable around the Pulley to the left open bracket on the Right Vertical Frame.
Install a Small Pulley to the bracket.
H.) Draw the Cable around the Small Pulley then clip the end of the Cable to the open slot on
the Left Butterfly.
I.) Attach the Butterfly Base Cover (#21) to the Butterfly Base (#13) to cover the left and right
pivot on the Butterfly Base. Secure the Cover to the Pivot with two M10 x ¾” Allen Bolts
(#95) and Ø ¾” Washers (#100).
J.) Align the holes and secure the Cover to the Butterfly Base with two M10 x 3 3/8” Allen
Bolts (#91), four Ø ¾” Washers (#100), and two M10 Aircraft Nuts (#102).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Butterfly Cable Loop Diagram
26
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 13 (See Diagram 13 and Upper Cable Loop Diagram)
A.) Attach the 130’” Upper Cable (#44) to the front opening on the Left Upper Frame (#34).
Attach a Pulley (#67) to the opening. Secure it with one M10 x 3 ½” Allen Bolt (#90), two
Ø 7/8” x 1” Pulley Bushings (#53), and one M10 Aircraft Nut (#102).
B.) Draw the Cable over the Pulley along the Left Upper Frame towards the back of the
machine. Make sure the Ball Stopper on the Cable is underneath the Left Upper Frame.
C.) Draw the Cable to the opening on the back of Left Upper Frame. Repeat Procedure A
above to install a Pulley.
D.) Draw the Cable around the Pulley then downward. Attach a Pulley to a Single Floating
Pulley Bracket (#14).
E.) Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾” Washers (#100), and
one M10 Aircraft Nut (#102). Let the Bracket hanging for now.
F.) Draw the Cable around the Pulley then upward to the first open bracket underneath the
Right Upper Frame (#1). Repeat Procedure E above to install a Pulley.
G.)Draw the Cable over the Pulley to the second open bracket under the Right Upper Frame.
Repeat Procedure E above to install another Pulley.
H.) Draw the Cable around the Pulley then downward between the two Guide Rods (#16) to
the Selector Rod (#28). Fully thread the Bolt on the end of the Cable into the Selector
Rod. Use the Nut on the end to tighten the Bolt.
I.) Connect the Lat Bar (#24) to the Upper Cable with a Chain (#75), and two Hooks (#76).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 13
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Upper Cable Loop Diagram
29
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 14 (See Diagram 14)
A.) Attach the end of the 103” Leg Press Cable (#47) to the bracket on the Leg Press
Frame (#36). Secure it with a M10 x 1 ¾” Allen Bolt (#94), two Ø ¾” Washers (#100),
and one M10 Aircraft Nut (#102).
B.) Draw the Cable to the first open bracket on the front of Left Base Frame (#32).
C.) Install a Pulley (#67) to the bracket with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾”
Washers (#100), and one M10 Aircraft Nut (#102).
D.) Draw the Cable to the opening on the bottom of Leg Press Frame. Install a Pulley to the
opening with one M10 x 2 5/8” Allen Bolt (#92), two Ø 7/8” x 5/8” Pulley Bushings (#5),
and one M10 Aircraft Nut (#102).
E.) Draw the Cable over the Pulley to the second open bracket on the Left Base Frame.
Repeat Procedure C above to install a Pulley.
F.) Draw the Cable underneath the Pulley then through the bottom of Left Seat Support
(#35) and Left Vertical Frame (#33) to the open bracket on the back of Left Base
Frame. Repeat Procedure C above to install a Pulley
G.)Draw the Cable around the Pulley then upward to the Single Floating Pulley Bracket
(#14) installed in Step-13.
H.) Connect the end of Cable to a Chain (#75) with a Hook (#76). Secure the Chain to the
Bracket with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers (#100), and one M10
Aircraft Nut (#102).
I.) Adjust the length of the Chain to adjust the tension of the Cable System.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 14
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Leg Press Cable Loop Diagram
32
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 15 (See Diagram 15)
A.) Attach four Weight Stack Covers (#41) to the Right Upper Frame (#1) and Right Base Frame (#31).
B.) Secure each Weight Stack Cover with two M10 x 5/8” Allen Bolts (#96) and Ø ¾” Washers (#100).
DIAGRAM 15
33
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
1
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
Ø 7/8” x 5/8” Pulley Bushing
5 ½” Butterfly Handle Grip
Foam Roll
Foam Roll End Cap
Ø 1 ½” x 1” Washer
5 3/8” Grip
1” Square End Cap
2” x 2” End Cap
2” x 1” End Cap
4
2
2
2
2
8
4
3
4
4
3
24
2
1
6
2
4
2
2
3
5
1
1
2
28
2
2
1
1
4
4
3
2
1
1
Right Upper Frame
Front Press Base
Front Press
2
3
1
4
5
6
7
8
9
Right Vertical Frame
Backrest Support Fame
Seat Post
Right Seat Support
Leg Developer
Butterfly Handle
Right Butterfly
Left Butterfly
Front Base Frame
Butterfly Base
Single Floating Pulley Bracket
Axle
Guide Rod
Foot Plate
Foot Plate Axle
Shiver Bar
Shiver Bar Handle
Butterfly Base Cover
Double Floating Pulley Bracket
Foam Tube
Lat Bar
4 ¾” x 2 ¾” Bracket
4 ½” x 2” Bracket
1
1
1
1
1
2
1
1
1
1
1
2
4
1
1
1
1
1
2
1
1
6
2
2 ¾” x 1” End Cap
2” x 2 ¾” End Cap
Pulley
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Small Pulley
Ø 1 ¾” x 1 5/8” Rubber Bumper
Ø 1 ¼” x Ø 3/8” Washer
Ø 1” Rubber Bumper
6” Grip
Lock Knob
Weight Selector Pin
Chain
Hook
Long T-shaped Lock Pin
Short T-shaped Lock Pin
Ø 2” End Cap
Weight Plate
Selector Stem
Ø 1” End Cap
Single Handle
Ankle Strap
M8 x 1 5/8” Allen Bolt
M8 x 2 ½” Allen Bolt
M6 x 5/8” Philips Screw
M10 x 6 ¼” Allen Bolt
M10 x 4 3/8” Allen Bolt
M10 x 3 ½” Allen Bolt
M10 x 3 3/8” Allen Bolt
M10 x 2 5/8” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 1” Allen Bolt
M10 x ¾” Allen Bolt
M10 x 5/8” Allen Bolt
M10 x 3 ¾” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 3 ½” Carriage Bolt
Angled Double Floating Pulley Bracket 1
Selector Rod
2
1
1
1
1
1
1
1
1
1
1
1
1
4
2
2
1
1
1
1
1
2
2
8
4
10
12
2
6 ¾” Front Press Base Axle
7 5/8” Front Press Axle
Right Base Frame
Left Base Frame
Left Vertical Frame
Left Upper Frame
Left Seat Support
Leg Press Frame
Right Handle
Left Handle
5
2
3
17
4
18
8
2
16
5
101
8
Leg Press Plate
Leg Press Adjustment Frame
Weight Stack Cover
Seat Pad
Backrest Board
130” Upper Cable
96” Butterfly Cable
157” Lower Cable
103” Leg Press Cable
140” Front Press Cable
Ø 1 ½” x 5/8” Rubber Bumper
Ø 1” Bushing
Ø 1 ½” x Ø 1” Washer
Ø 2 3/8” x 1” Rubber Bumper
Ø 7/8” x 1” Pulley Bushing
Ø 1” x Ø 5/8” Washer
Ø 1 ¼” x Ø 5/8” Bushing
100 Ø ¾” Washer
101
102
Ø 5/8” Washer
M10 Aircraft Nut
61
34
Download from Www.Somanuals.com. All Manuals Search And Download.
MP-4500 WEIGHT RESISTANCE CHART
WEIGHT PLATE
Station
Low Pulley
Lat Pull
1
2
3
4
5
6
7
22 33
30 40
44
50
50
55
60
62
66
70
74
77
80
86
88
90
98
Leg Developer 26 38
Leg Press
Front Press
Butterfly
36 60
20 34
10 16
84 108 132 156 180
48
22
62
28
76
34
90 104
40
46
WEIGHT PLATE
10 11 12
Station
Low Pulley
Lat Pull
8
9
13
14
99 110 121 132 143 154 165
100 110 120 130 140 150 160
110 122 134 146 158 170 182
204 228 252 276 300 324 348
118 132 146 160 174 188 202
Butterfly
Leg Press
Front Press
Butterfly
52
58
64
70
76
82
88
*Numbers are approximate. Actual weight may vary.
*Value for butterfly is for each arm.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of two years on the Frame from
the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation
under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state.
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|