NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
MARCY DIAMOND ELITE
POWER CAGE
MD PWR-8
Warranty
Ordering Parts
Model
MD PWR-8
Retain This
Manual for
Reference
08-27-05
OWNER'S
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Rear Base and Upper Frame. If the labels
are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the
labels in location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CAGE HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CAGE HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CAGE ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended this machine be assembled by two or more people to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Right Support (#5) to the Right Stabilizer (#1). Attach the Cross Brace (#3)
to the Right Support. Align the holes and secure them with two M10 x 3 ¾” Carriage
Bolts (#50), Ø ¾” Washers (#64), and M10 Aircraft Nuts (#66). Repeat the same step
to install the Left Support (#6) on the other side. NOTE: DO NOT tighten the Nuts
and Bolts yet.
B.) Cover the end of the Stabilizers with four 2” x 2 ¾” Stabilizer End Caps (#37).
DIAGRAM 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach an Upright Beam (#4) to the Right Stabilizer (#1) and the Right Support (#5). Secure
the Upright Beam to the Right Stabilizer with two M10 x 2 3/8” Carriage Bolts (#52), one 5
½” x 2” Bracket (#26), two Ø ¾” Washers (#64), and two M10 Aircraft Nuts (#66).
B.) Secure the Upright Beam to the Right Support with two M10 x ¾” Allen Bolts (#60) and Ø
¾” Washers (#64).
C.) Repeat Steps A and B above to install the other side.
D.) Place the Upper Frame (#8) onto the two Upright Beams. Secure each end with three M10
x 5/8” Allen Bolts (#61) and Ø ¾” Washers (#64).
DIAGRAM 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Rear Stabilizer (#21) to the Cross Brace (#3). Secure it with two M10 x 3 ½”
Carriage Bolts (#51), one 4 ¾” x 2” Bracket (#25), two Ø ¾” Washers (#64) and two M10
Aircraft Nuts (#66).
B.) Slide the Sliding Weight Post (#13) onto the Rear Vertical Frame (#7). Attach the Vertical
Frame to the Rear Stabilizer. Secure it with two M10 x 2 ½” Allen Bolts (#56), four Ø ¾”
Washers (#64), and two M10 Aircraft Nuts (#66). Slide two Ø 3” x ½” Spacers (#35) onto the
weight posts. Attach two Olympic Sleeves (#14) onto the posts.
C.) Attach four Olympic Weight Posts (#15) to the Right & Left Supports (#5 & 6). Secure each
Post with one M10 x 1 3/8” Allen Bolt (#59) and Ø ¾” Washer (#64). Slide four Olympic
Sleeves (#14) onto the weight Posts. Attach six Spring Clips (#31) onto the Olympic
Sleeves.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Lat Bar Frame Bracket (#20) to the top of the Rear Vertical Frame (#7).
Secure it with two M10 x 5/8” Allen Bolts (#61) and Ø ¾” Washers (#64).
B.) Attach the Left & Right Lat Bar Frames (#10 & 9) to the Lat Bar Frame Bracket (#20).
Secure them with two M10 x 5 1/4” Allen Bolts (#53), four Ø ¾” Washers (#64), and two
M10 Aircraft Nuts (#66).
C.) Secure each Lat Bar Frame to the Upper Frame (#8) with one M10 x 4 ½” Allen Bolt
(#54), two Ø ¾” Washers (#64) and one M10 Aircraft Nut (#66).
D.) Securely tighten all Nuts and Bolts previously installed.
E.) Attach a Pulley (#36) to the open slot on the Left Lat Bar Frame (#10). Secure it with one
M10 x 2 1/8” Allen Bolt (#57), two Pulley Bushings (#41), and one M10 Aircraft Nut (#66).
Repeat the same procedure to install the other side.
F.) Attach a Pulley to the bracket on the Lat Bar Frame Bracket (#20). Secure it with one
M10 x 1 ¾” Allen Bolt (#58), two Ø ¾” Washers (#64), and one M10 Aircraft Nut (#66).
G.)Insert the Right & Left Bar Catches (#16 & 18), Right & Left Safety Catches (#17 & 19)
into the selected holes on the Upright Beams to obtain the desired position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 283” Upper Cable (#48) to the swivel pulley pre-installed in the front of the
Right Lat Bar Frame (#9). Install a Ball Stopper (#46) onto the end of the Cable.
Attach the U-shaped Connector (#28) to the end of the Cable.
B.) Attach a Short Chain (#30) in between the openings on the Connector and secure it
with a M10 x 1 3/8” Allen Bolt (#59), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut
(#66).
C.) Draw the Cable over the Pulley and pull through the Cable sleeve on the Right Lat Bar
Frame. Draw the Cable along the Frame towards the back of the machine to the Pulley
previously installed. Draw the Cable around the Pulley then downward to the Double
Floating Pulley Bracket (#24).
D.) Attach two Pulleys (#36) to the Bracket. Secure them with a M10 x 2 ¾” Allen Bolt
(#55), two Ø ¾” Washers (#64), and one M10 Aircraft Nut (#66).
E.) Draw the Cable around the back Pulley then upward to the bottom of the Lat Bar Frame
Bracket (#20). Install a Pulley.
F.) Draw the Cable around the Pulley then back down to the Double Floating Pulley
Bracket (#24) again. Let the Bracket hanging for now.
G.) Draw the Cable around the front Pulley then upward towards the Pulley on the Left Lat
Bar Frame (#10).
H.) Draw the Cable over the Pulley then along the Left Lat Bar Frame (#10) towards the
front of the machine. Insert the Cable through the Cable sleeve and over the pre-
installed Pulley on the front of the Left Lat Bar Frame.
I.) Install a Ball Stopper (#46) at the end of the Cable and attach a U-shaped Connector
(#28) to the end. Attach a Short Chain (#30) in between the openings on the Connector
and secure it with a M10 x 1 3/8” Allen Bolt (#59), two ∅ ¾” Washers (#64), and one
M10 Aircraft Nut (#66).
J.) Connect the Lat Bar (#11) or Single Handles (#33) to the Short Chains using C-clips
(#32).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 5
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach the Ball end of the 205” Lower Cable (#49) to a Pulley (#36).
B.) Attach the Pulley to the open bracket on the Cross Brace (#3). Secure it with one M10 x
1 ¾” Allen Bolt (#58), two Ø ¾” Washers (#64), and one M10 Aircraft Nut (#66).
C.) Draw the Cable underneath the Pulley then upward to the hanging Double Floating
Pulley Bracket (#24) installed in Step-5. Install another Pulley.
D.) Draw the Cable downward to the open bracket on the Rear Stabilizer (#21). Install
another Pulley.
E.) Pull the Cable around the Pulley and upward to the Pulley previously installed on the top
of the Lat Bar Support Bracket (#20).
F.) Draw the Cable around the Pulley then downward to the bracket on the Sliding Weight
Post (#13). Secure the end of Cable to the bracket with one M10 x 1 3/8” Allen Bolt
(#59), two Ø ¾” Washers (#64), and one M10 Aircraft Nut (#66).
G.) Attach the Long Chain (#29) to the end of the Cable using a C-clip (#32). Attach the
Shiver Bar (#23) to the Chain using another C-clip.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 6
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DIAGRAM
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CAGE PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
9
Right Stabilizer
Left Stabilizer
Cross Brace
Upright Beam
Right Support
Left Support
Rear Vertical Frame
Upper Frame
1
1
1
2
1
1
1
1
1
1
1
2
1
6
6
1
1
1
1
1
1
2
1
1
1
2
8
2
1
2
6
4
2
4
2
11
4
1
1
6
4
2
4
4
8
2
1
1
1
4
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
M10 x 3 ½” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
M10 x 5 1/4” Allen Bolt
M10 x 4 ½” Allen Bolt
M10 x 2 ¾” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 2 1/8” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 1 3/8” Allen Bolt
M10 x ¾” Allen Bolt
M10 x 5/8” Allen Bolt
M6 x 5/8” Allen Bolt
M6 x ¼” Allen Screw
Ø ¾” Washer
2
4
2
2
1
2
2
7
7
4
8
1
8
60
1
Right Lat Bar Frame
10 Left Lat Bar Frame
11 Lat Bar
12 Chrome Panel
13 Sliding Weight Post
14 Olympic Sleeve
15 Olympic Weight Post
16 Right Bar Catch
17 Right Safety Catch
18 Left Bar Catch
19 Left Safety Catch
20 Lat Bar Frame Bracket
21 Rear Stabilizer
22 Swivel Pulley Bracket
23 Shiver Bar
24 Double Floating Pulley Bracket
25 4 ¾” x 2” Bracket
26 5 ½” x 2” Bracket
27 Chrome Panel Screw
28 U-shaped Connector
29 Long Chain
30 Short Chain
31 Spring Clip
32 C-Clip
33 Single Handle
34 Handle Grip
35 Ø 3” x ½” Spacer
36 Pulley
37 2” x 2 ¾” Stabilizer End Cap
38 2” End Cap
39 2” End Cap
40 1 5/8” x 2 3/8” End Cap
41 Ø 5/8” Pulley Bushing
42 Sleeve
43 Ø 1 ½” Bushing
44 Ring Cap
45 Ø 1” End Cap
46 Ball Stopper
47 Ø 1 ½” x 5/8” Rubber Bumper
48 283” Upper Cable
49 205” Lower Cable
50 M10 x 3 ¾” Carriage Bolt
Ø ½” Washer
M10 Aircraft Nut
29
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI-PURPOSE BENCH HARDWARE PACK
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended this machine be assembled by two or more people to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with two
M10 x ¾” Allen Bolts (#35) and ∅ ¾” Washers (#41). Attach a Lock Knob (#23) to the hole
underneath the Main Frame.
B.) Slide the Sliding Block (#8) onto the Incline Adjustment Bar (#9). Align the hole then secure it
with a Lock Knob (#23) to hold the Sliding Block in position.
C.) Attach the Incline Adjustment Bar (#9) to the brackets on the Main Frame. Secure each end
with one M10 x 2 ½” Carriage Bolt (#34), ∅ ¾” Washer (#41), and M10 Aircraft Nut (#43).
DIAGRAM 1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach four Bushings (#26) to a Seat Support Frame (#6).
B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and
secure them with one M10 x 1 ¾” Allen Bolt (#36) and ∅ ¾” Washer (#41). Repeat the same
procedure to install the other side.
C.) Attach two Bushings (#26) to the pivot on the Sliding Block (#8). Attach two Bushings to each
Backrest Supports (#7). Align the holes and secure them with one M10 x 6 ¾” Allen Bolt (#37), two
∅ ¾” Washers (#41), and one M10 Aircraft Nut (#43). Do not over tighten the nut and bolt. The
Supports need to swivel on the Bolt.
D.) Attach two Bushings to the pivot on the Main Frame (#1). Loosen and pull the Lock Knob on the
Sliding Block (#8). The Sliding Block needs to be able to slide on the Chromed Incline Adjustment
Bar (#9). Align the two Seat Support Frames (#6) to both ends of the pivot on Main Frame. Secure
them with one M10 x 8 ¼” Allen Bolt (#38), two ∅ ¾” Washers (#41), and one M10 Aircraft Nut
(#43).
E.) Use the Lock Knob on the Sliding Block (#8) to adjust and secure the backrest incline position.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with
four M8 x 2” Allen Bolts (#39) and ∅ 5/8” Washers (#42).
B.) Place the Seat Pad (#13) onto the Seat Support Frames (#6). Secure it with
four M8 x 2” Allen Bolts (#39) and Ø 5/8” Washers (#42).
DIAGRAM 3
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with
an Axle (#17), two M10 x ¾” Allen Bolts (#35), and two ∅ ¾” Washers (#41).
B.) Insert one Foam Tube (#10) halfway through the hole on the Main Frame. Insert two Foam
Tubes halfway through the holes on the Leg Developer (#5). Push six Foam Rolls (#24)
onto the Tubes from both ends. Plug six Foam Roll End Caps (#25) into the ends.
C.) Slide the Olympic Sleeve (#20) onto the weight post on the Leg Developer. Attach a
Spring Clip (#22) to the Sleeve.
DIAGRAM 4
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8”
Allen Bolts (#40) and two ∅ 5/8” Washers (#42). Insert the Arm Curl Stand into the front
opening on the Main Frame (#1). Use the Lock Knob to hold the desired Arm Curl height.
B.) Attach the Curl Bar Support Frame (#11) to the open bracket on the Leg Developer (#5).
Lock it with a L-shaped Pin (#21).
C.) Remove the Pin, Curl Bar Handle and Arm Curl when using the Leg Developer to exercise.
DIAGRAM 5
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI-PURPOSE BENCH PARTS LIST
KEY NO.
1
DESCRIPTION
Main Frame
Q’ty
1
2
Front Stabilizer
1
3
Rear Stabilizer
1
4
5
Arm Curl Stand
Leg Developer
1
1
6
7
8
Seat Support Frame
Backrest Support
Sliding Block
2
2
1
9
Incline Adjustment Bar
Foam Tube
1
3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Curl Bar Support Frame
Curl Bar Handle
Seat Pad
Backrest Board
Arm Curl Pad
Curl Bar Handle Grip
Axle
Ø 2 3/8” Bushing
Ø 1 3/8” Bushing
Olympic Sleeve
L-shaped Pin
Spring Clip
Lock Knob
Foam Roll
Foam Roll End Cap
Bushing
1
1
1
1
1
2
1
2
2
1
1
1
2
6
6
16
1
1
1
2
12
3
4
2
6
2
1
1
8
2
14
10
4
3 1/8” x 1 5/8” End Cap
Ø 1” Cone-shaped End Cap
Ø 1” End Cap
1 5/8” x 2 3/8” End Cap
1 5/8” x ¾” End Cap
2” Sliding Block Sleeve
Stabilizer End Cap
M10 x 2 ½” Carriage Bolt
M10 x ¾” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 6 ¾” Allen Bolt
M10 x 8 ¼” Allen Bolt
M8 x 2” Allen Bolt
M8 x 5/8” Allen Bolt
Ø ¾” Washer
Ø 5/8” Washer
M10 Aircraft Nut
25
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal
use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty
extends only to the original purchaser.
repairing, at IMPEX's option.
IMPEX's obligation under this Warranty is limited to replacing or
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that specifically
set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential
damages or whatsoever natures.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.Model
2.Description of Parts
3.Part Number
4.Date of Purchase
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|