NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY DIAMOND
OLYMPIC BENCH
Hardware Identifier
Assembly Instruction
Parts List
MD-8861
Warranty
Ordering Parts
Model
MD-8861
Retain This
Manual for
Reference
07-03-08
IMPEX® INC.
OWNER'S
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
14. Maximum weight on uprights: 600 lbs.
15. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Left Upright Beam. If the label is missing or
illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Connect the Right and Left Upright Beams (#1 & #2) with a Cross Brace (#3) in the mid-span.
Secure each end with two M10 x 4 ¾” Carriage Bolts (#54), one 5 ½” x 2” Bracket (#46), two Ø
¾” Washers (#64), and two M10 Aircraft Nuts (#67).
B.) Attach a Weight Post (#14) to the rear diagonal support on the Left Upright Beam. Secure it
with one M10 x ¾” Allen Bolt (#59) and ∅ ¾” Washer (#64). Slide an Olympic Sleeve (#44)
onto the Weight post. Attach a Spring Clip (#48) to the Sleeve. Repeat the same procedure to
install the other side.
C.) Place the Backrest Adjustment Bar (#29) onto the selected slot on the Upright Beams.
D.) Attach the Left & Right Squat Bar Catches (#11 & #12) onto the two Upright Beams. Insert the
Right & Left Bar Catches (#7 & #8), Right & Left Safety Catches (#9 & #10) into the selected
holes on the two Upright Beams.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Slide the Sliding Block (#6) onto the Main Seat Support (#4). Thread a M18 x ∅ 5/8” Lock
Knob (#47) into the selected hole to hold the Sliding Block in position.
B.) Attach the Main Seat Support to the Cross Brace (#3).
C.) Secure it from the rear of the Cross Brace with two M10 x 2 ¾” Allen Bolts (#58), one 2 ½”
x 2” Bracket (#21), and two ∅ ¾” Washers (#64).
D.) Secure it from the top of Cross Brace and Main Seat Support with two M10 x 3 ½” Carriage
Bolts (#55), two M10 x 2 3/8” Carriage Bolts (#56), two Triangular Brackets (#15), four Ø
¾” Washers (#64), and four M10 Aircraft Nuts (#67).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the brackets at the end of the Backrest Supports (#32) to the pivot on the Sliding
Block (#6). Align the holes on the Seat Support (#16) to the brackets on the Backrest
Supports. Secure them together with one M12 x 7 5/8” Allen Bolt (#60), two ∅ 1”
Washers (#66) and one M12 Aircraft Nut (#69).
B.) Attach the Backrest Board (#26) to the Backrest Supports. Secure it with four M8 x 1 5/8”
Allen Bolts (#62) and Ø 5/8” Washers (#65). Place the other end of Backrest Board rest
against the Backrest Adjustment Bar.
C.) Place the Seat Pad (#27) onto the Seat Support (#16). Secure it with four M8 x 1 5/8”
Allen Bolts (#62) and Ø 5/8” Washers (#65).
D.) Insert a 4 ¾” Lock Pin (#36) into the selected hole on the Seat Support to obtain the
desired Seat inclined position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Insert two M10 x 2 3/8” Carriage Bolts (#56) all the way through the holes on the Leg
Developer Holder (#5), then insert the two Bolts through the holes on the Main Seat
Support (#4). Attach the Leg Developer Holder to the Main Seat Support. Secure them with
the two M10 x 2 3/8” Carriage Bolts, one 4 ¾” x 2” Bracket (#45), two Ø ¾” Washers (#64),
and two M10 Aircraft Nuts (#67). Thread a M18 x Ø 5/8” Lock Knob (#47) into the nut on
the Leg Developer Holder.
B.) Attach the Leg Developer (#13) to the Leg Developer Holder. Secure it with one M10 x 3
½” Allen Bolt (#57), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut (#67).
C.) Insert two Foam Tubes (#18) halfway through the holes on the Leg Developer. Push four
Foam Rolls (#37) onto the Tubes from both ends. Plug four Foam Roll End Caps (#43)
into the ends.
D.) Slide an Olympic Sleeve (#44) onto the weight post on the Leg Developer. Attach a Spring
Clip (#48) to the Sleeve.
E.) Attach the Arm Curl Handle (#30) to the back holes on the Leg Developer. Secure it with
one 3” Lock Pin (#35). Attach the Abdominal Strap (#31) to the front holes on the Leg
Developer. Secure it with another 3” Lock Pin.
DIAGRAM 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Arm Curl Pad (#28) to the Arm Curl Bracket (#34). Secure it with two M8 x 5/8”
Allen Bolts (#61) and Ø 5/8” Washers (#65). Attach the Arm Curl Bracket to the bracket on
the Arm Curl Stand (#17). Insert the M8 x 3 ½” Allen Bolt (#63) through the open track on
the Arm Curl Stand and the holes on the Arm Curl Bracket then secure the Bolt with two ∅
5/8” Washers (#65), and one M8 Aircraft Nut (#68). Do not over tighten the Nut and Bolt.
The Bolt needs to be able to slide on the rack freely.
B.) Insert the Arm Curl Stand into the top opening on the Leg Developer Holder. Use the M18
x Ø 5/8” Lock Knob (#47) installed in Step-4 to secure the Stand.
C.) Pull up and Flip the Arm Curl Pad along the track facing the back when doing Abdominal
exercises using the Abdominal Straps.
D.) Remove the Arm Curl Stand and Abdominal Strap when doing Leg Developer exercises.
DIAGRAM 5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Right Upright Beam
Left Upright Beam
Cross Brace
Main Seat Support
Leg Developer Holder
Sliding Block
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
4
2
1
1
2
2
2
1
1
1
1
1
1
2
2
1
2
1
4
1
1
4
1
1
4
3
1
2
2
3
4
6
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
1” Square End Cap
Ø ¾” Cone-shaped End Cap
6” Arm Curl Handle Grip
M10 x 4 ¾” Carriage Bolt
M10 x 3 ½” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
M10 x 3 ½” Allen Bolt
M10 x 2 ¾” Allen Bolt
M10 x ¾” Allen Bolt
M12 x 7 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
M8 x 1 5/8” Allen Bolt
M8 x 3 ½” Allen Bolt
Ø ¾” Washer
Ø 5/8” Washer
Ø 1” Washer
M10 Aircraft Nut
M8 Aircraft Nut
M12 Aircraft Nut
M6 x 5/8” Philips Screw
4
12
2
4
2
4
1
2
2
1
2
8
1
16
12
2
11
1
Right Bar Catch
Left Bar Catch
9
Right Safety Catch
Left Safety Catch
Left Squat Catch
Right Squat Catch
Leg Developer
Weight Post
Triangular Bracket
Seat Support
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Arm Curl Stand
Foam Tube
3 ¾” x 3 3/8” Rubber Bumper
3 ¾” x 5 ¾” Rubber Bumper
2 ½” x 2” Bracket
2 3/8” x Ø 1 ¾” Sleeve
4” x 2” Sleeve
4” x 2” End Cap
2 3/8” End Cap
Backrest Board
Seat Pad
1
1
1
Arm Curl Pad
Backrest Adjustment Bar
Arm Curl Handle
Abdominal Strap
Backrest Support
Panel
Arm Curl Bracket
3” Lock Pin
4 ¾” Lock Pin
Foam Roll
Abdominal Strap Connector
Strap Buckle
Ø 1” Bushing
Ø 1 ½” x 5/8” Rubber Bumper
2” End Cap
Foam Roll End Cap
Olympic Sleeve
4 ¾” x 2” Bracket
5 ½” x 2” Bracket
M18 x Ø 5/8” Lock Knob
Spring Clip
Ø 1” End Cap
Rivet
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
®"
IMPEX Inc. ("IMPEX ) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of two years on the Frame from
the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation
under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line at www.impex-fitness.com
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|