NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY® CLASSIC
MID-SIZE BENCH
MCB 880-MG
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MCB-880MG
Retain This
Manual for
Reference
07-16-08
OWNER'S
MANUAL
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the same station.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Rear Stabilizer, Base Frame, and Lat Bar
Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for
replacements. Apply the labels in location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended two or people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Attach the two Base Frames (#65) together on a flat surface. Attach the Left & Right Upright
Beams (#67 & #68) onto the two Base Frames. Secure each Upright with two M10 x 3 ¾”
Carriage Bolts (#46), Ø ¾” Washers (#39), and M10 Aircraft Nuts (#51). Do NOT tighten the
nuts and bolts yet.
B.) Connect the two Upright Beams with the Cross Brace (#69) in the mid-span. Secure each end
with two M10 x 3 ¾” Carriage Bolts (#46), one Curve Bracket (#76), two Ø ¾” Washers (#39),
and two M10 Aircraft Nuts (#51).
C.) Insert two Crutches (#73) into the openings on the Upright Beams. Use the M18 Lock Knobs
(#54) to secure the Crutches in position.
D.) Attach the Right & Left Safety Hooks (#63 & #64) to the two Crutches. Secure each Hook with
a M8 Aircraft Nut (#52).
E.) Attach two Weight Posts (#78) to the Cross Brace. Secure each Weight Post with one M10 x
¾” Allen Bolt (#32) and Ø ¾” Washer (#39). Attach an Olympic Sleeve (#14) to each Weight
Post. Attach a Spring Clip (#15) to each Sleeve.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Lat Bar Frame Support (#66) onto the joint of the two Base Frames (#65).
Align the holes and secure them together with two M10 x 3 ¾” Carriage Bolts (#46), Ø ¾”
Washers (#39) and M10 Aircraft Nuts (#51).
B.) Attach the Lat Bar Frame Support (#66) to the bracket on the Cross Brace (#69). Attach
the Rear Diagonal Support Frame (#77) to the back of Lat Bar Frame. Align the holes
and secure them together with one M10 x 2 ¾” Carriage Bolt (#47), Ø ¾” Washer (#39)
and M10 Aircraft Nut (#51) to the top holes, one M10 x 2 ¾” Allen Bolt (#20), two Ø ¾”
Washers (#39) and one M10 Aircraft Nut (#51) to the bottom holes.
C.) Slide the Sliding Weight Post (#71) onto the Lat Bar Frame (#70) from the bottom. Insert
the Lat Bar Frame (#70) into the Lat Bar Frame Support (#66). Secure it with two M10 x 2
3/8” Allen Bolts (#48), four Ø ¾” Washers (#39) and two M10 Aircraft Nuts (#51).
D.) Attach an Olympic Sleeve (#14) onto the Sliding Weight Post. Attach a Spring Clip (#15)
onto the Sleeve. Securely tighten all Nuts and Bolts previously installed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the 57” Cable (#74) to a Pulley (#57). Attach the Pulley to the top opening on the
Lat Bar Frame (#70). Secure it with a M10 x 2 3/8” Allen Bolt (#48), two Pulley Bushings
(#59), and one M10 Aircraft Nut (#51). Make sure the ball stopper on the Cable is
underneath the opening.
B.) Draw the Cable over the Pulley to the open bracket on the rear of the Lat Bar Frame.
Attach a Pulley and secure it with one M10 x 2” Allen Bolt (#49), one L-shaped Cable
Retainer (#75), two Ø ¾” Washers (#39), and one M10 Aircraft Nut (#51).
C.) Draw the Cable around the Pulley then downward to the bracket on the Sliding Weight
Post (#71). Secure it with one M10 x ¾” Allen Bolt (#32), two Ø ¾” Washers (#39), and
one M10 Aircraft Nut (#51).
D.) Insert a M8 x 2 1/8” Allen Bolt (#50) through the holes on the Lat Bar Frame and secure
it with a M8 Aircraft Nut (#52).
E.) Connect the Lat Bar (#72) to the Cable with two C-clips (#62) and one Chain (#61).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Main Frame (#1) onto the Front & Rear Stabilizers (#2 & #6). Secure each end
with two M10 x ¾” Allen Bolts (#32) and Ø ¾” Washers (#39).
DIAGRAM 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the two Backrest Supports (#3) to the pivot on the Main Frame (#1). Secure it with
one M12 x 5 ¾” Allen Bolt (#31), two Ø1” Washers (#38), and one M12 Aircraft Nut (#36).
Do not over tighten the nut and bolt. Make sure the Backrest Supports are able to swivel.
B.) Attach the Backrest Incline Support (#4) in between the two Backrest Supports. Secure it
with one M12 x 5 ¾” Allen Bolt (#31), two Ø 1” Washers (#38), and one M12 Aircraft Nut
(#36). Attach the other end of the Backrest Incline Support to a selected slot on the Main
Frame to obtain the desired backrest incline position.
C.) Place the Backrest Board (#12) to the Backrest Supports. Secure it with four M8 x 1 5/8”
Allen Bolts (#34) and Ø 5/8” Washers (#40).
D.) Place the Seat (#11) onto the Main Frame. Secure it with four M8 x 1 5/8” Allen Bolts
(#34) and Ø 5/8” Washers (#40).
DIAGRAM 5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6)
A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it
with one Axle (#42), two M10 x 5/8” Allen Bolts (#30), and two Ø ¾” Washers (#39).
Do not over tighten the bolts. Make sure the Leg Developer is able to swivel.
B.) Insert the U-shaped Pin (#10) into the tube in front of the Main Frame. Secure it with
one Spring (#29), Ø ½” Washer (#28), and M6 x 5/8” Philips Screw (#41).
C.) Insert three Foam Tubes (#9) halfway through the holes on the Main Frame and Leg
Developer. Push six Foam Rolls (#26) onto the Tubes from both ends. Plug six Foam
Roll End Caps (#21) into the Tubes from both ends.
D.) Attach the Curl Bar Handle Support (#45) to the bracket on the Leg Developer.
Secure it with a L-shaped Pin (#27).
E.) Attach an Olympic Sleeve (#14) onto the weight post on the Leg Developer. Attach a
Spring Clip (#15) to the Sleeve.
DIAGRAM 6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7)
A.) Attach the Arm Curl Pad (#13) to the Arm Curl Stand (#7). Secure it with two M8 x ¾” Allen
Bolts (#33) and Ø 5/8” Washers (#40).
B.) Insert the Arm Curl Stand into the front opening on the Main Frame. Use a Lock Knob (#16)
to secure the Stand at desired height.
C.) The Leg Developer can be locked when doing sit up exercises. Simply pull the U-shaped Pin
(#10) out and drop into the hole on the Leg Developer. Remove the Pin when doing Leg
Developer exercises.
D.) Remove the Arm Curl Stand and Curl Bar Handle when using Leg Developer.
DIAGRAM 7
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DIAGRAM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
M10 x 3 ¾” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2” Allen Bolt
M8 x 2 1/8” Allen Bolt
M10 Aircraft Nut
M8 Aircraft Nut
¼” Philips Screw
M18 Lock Knob
1 ¾” Square End Cap
1 ½” x 3” End Cap
Pulley
10
1
3
1
1
17
3
2
2
1
2
2
2
2
2
1
2
1
1
2
1
1
1
1
1
1
1
2
1
1
2
1
2
1
2
3
4
5
6
7
8
Main Frame
1
1
2
1
1
1
1
1
3
1
1
1
1
4
4
1
2
2
5
1
6
2
3
4
1
6
1
1
1
2
2
7
2
8
1
2
2
4
29
10
1
1
2
2
1
Front Stabilizer
Backrest Support
Backrest Incline Support
Leg Developer
Rear Stabilizer
Arm Curl Stand
Curl Bar
Foam Tube
U-shaped Pin
Seat Pad
Backrest Board
Arm Curl Pad
Olympic Sleeve
Spring Clip
Lock Knob (Impex Logo)
2 3/8” x 1 5/8” End Cap
1” Square End Cap
Ø 1” End Cap
M10 x 2 ¾” Allen Bolt
Foam Roll End Cap
Ø 2 3/8” Bushing
2” Sleeve
Stabilizer End Cap
Rubber Bumper
Foam Roll
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Ø 3” Sleeve
Pulley Bushing
Lat Bar Handle Grip
Chain
C-clip
Right Safety Hook
Left Safety Hook
Base Frame
Lat Bar Frame Support
Left Upright Beam
Right Upright Beam
Cross Brace
Lat Bar Frame
Sliding Weight Post
Lat Bar
Crutch
57” Cable
L-shaped Cable Retainer
Curve Bracket
Rear Diagonal Support Frame
Weight Post
L-shaped Pin
Ø ½” Washer
Spring
M10 x 5/8” Allen Bolt
M12 x 5 ¾” Allen Bolt
M10 x ¾” Allen Bolt
M8 x ¾” Allen Bolt
M8 x 1 5/8” Allen Bolt
M6 x ½” Philips Screw
M12 Aircraft Nut
Ø 1 ½” Bushing
Ø 1” Washer
Ø ¾” Washer
Ø 5/8” Washer
M6 x 5/8” Philips Screw
Axle
Curl Bar Handle Grip
Ø ¾” Bushing
Curl Bar Handle Support
15
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of two years on the Frame from
the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation
under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state.
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|