NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY CLASSIC
WEIGHT BENCH
Hardware Identifier
Assembly Instruction
Parts List
MCB-5693
Warranty
Ordering Parts
Model
MCB-5693
Retain This
Manual for
Reference
07-23-08
OWNER'S
MANUAL
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
14. Maximum weight on uprights: 600 lbs.
15. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible,
please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Plug four 2 ¾” x 2” End Cap (#21) onto the Left and Right Upright Beams (#1) & (#2).
B.) Connect the Left and Right Upright Beams with a Cross Brace (#3) in the mid-span. Secure
each end of the Cross Brace with two M10 x 2 ¾” Carriage Bolts (#42), one 4 ¾” x 2 ¾”
Bracket (#17), two Ø ¾” Washers (#39), and two M10 Aircraft Nuts (#50).
C.) Place the Backrest Adjustment Bar (#8) onto the selected slot on the Upright Beams to obtain
desired backrest incline.
D.) Insert the two Crutches (#7) into the two Upright Beams. Use the Lock Knob (#26) to lock the
Crutch in desired position.
DIAGRAM 1
Download from Www.Somanuals.com. All Manuals Search And Download.
6
STEP 2 (See Diagram 2)
A.) Attach the Main Seat Support (#4) to the Leg Developer Holder (#5). Secure it with two
M10 x 2 ½” Carriage Bolts (#41), two Ø ¾” Washers (#39), and two M10 Aircraft Nuts
(#50). Do not tighten the Nuts and Bolts yet.
B.) Attach the Main Seat Support to the Cross Brace (#3). Secure it with two M10 x 2 ½”
Carriage Bolts (#41), two Ø ¾” Washers (#39), and two M10 Aircraft Nuts (#50).
C.) Securely tighten all Nuts and Bolts.
DIAGRAM 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the side-holes on the end of the Backrest Supports (#11) to the pivot on the Main
Seat Support (#4). Secure them together with one M12 x 7 ¼” Hex Bolt (#43), two ∅ 1”
Washers (#40) and one M12 Aircraft Nut (#51).
B.) Attach the Backrest Board (#13) to the Backrest Supports. Secure it with four M8 x 1 ½”
Allen Bolts (#47) and Ø 5/8” Washers (#38). Place the other end of Backrest Board rest
against the Backrest Adjustment Bar.
C.) Attach the two Seat Brackets (#6) onto the Main Seat Support. Secure each Seat Bracket
with one M10 x 2 ½” Allen Bolts (#44), two Ø ¾” Washers (#39), and one M10 Aircraft
Nut (#50).
D.) Place the Seat Pad (#14) onto the Seat Brackets. Secure it with four M8 x 1 ½” Allen
Bolts (#47) and Ø 5/8” Washers (#38).
DIAGRAM 3
Download from Www.Somanuals.com. All Manuals Search And Download.
8
STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#9) to the Leg Developer Holder (#5). Secure it with one Axle
(#54), two M10 x 5/8” Allen Bolts (#45), and two ∅ ¾” Washers (#39).
B.) Insert two Foam Tubes (#12) halfway through the holes on the Leg Developer. Push four
Foam Rolls (#19) onto the Tubes from both ends. Plug four Foam Roll End Caps (#29)
into the ends.
C.) Slide an Olympic Sleeve (#28) onto the weight post on the Leg Developer. Attach a Spring
Clip (#20) to the Sleeve.
D.) Attach the Arm Curl Handle (#36) to the back holes on the Leg Developer. Secure it with
one Lock Pin (#30). Attach the Abdominal Strap (#33) to the front holes on the Leg
Developer. Secure it with another Lock Pin.
E.) Attach the Arm Curl Pad (#15) to the Arm Curl Bracket (#37). Secure it with two M8 x 5/8”
Allen Bolts (#46) and two Ø 5/8” Washers (#38). Attach the Arm Curl Bracket to the bracket
on Arm Curl Stand (#10). Insert the M8 x 3 ½” Allen Bolt (#48) through the open track on
the Arm Curl Stand and the hole on Arm Curl Bracket then secure with two Ø 5/8” Washers
(#38) and one M8 Aircraft Nut (#49). Do not over tighten the Nut and Bolt. Make sure
the Bolt slides on the track freely.
F.) Insert the Arm Curl Stand into the Leg Developer Holder. Use the Lock Knob (#22) to lock
the Arm Curl Stand in position.
G.)Pull and flip up the Arm Curl Pad along the track facing the back when doing Abdominal
exercises using the Abdominal Strap.
H.) Remove Abdominal Strap and Arm Curl Handle when doing Leg Developer exercises.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Q’ty
PARTS LIST
KEY NO. DESCRIPTION
46
47
48
49
50
51
52
53
54
55
M8 x 5/8” Allen Bolt
M8 x 1 ½” Allen Bolt
M8 x 3 ½” Allen Bolt
M8 Aircraft Nut
M10 Aircraft Nut
M12 Aircraft Nut
ST2.9 Screw
Ø 2 3/8” Bushing
Axle
Ø 1” End Cap
2
8
1
1
10
1
4
2
1
1
1
2
1
2
3
Left Upright Beam
Right Upright Beam
Cross Brace
1
1
1
1
1
2
2
1
1
1
2
2
1
1
1
1
2
1
4
1
4
3
2
2
2
1
2
1
4
2
4
2
1
1
1
1
1
12
14
2
4
4
1
2
2
4
5
6
Main Seat Support
Leg Developer Holder
Seat Bracket
7
Crutch
8
9
Backrest Adjustment Bar
Leg Developer
#5 Allen Wrench (Tool)
#6 Allen Wrench (Tool)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Arm Curl Stand
Backrest Support
Foam Tube
Backrest Board
Seat Pad
Arm Curl Pad
4 3/8” x 1 ¾” Bracket
4 ¾” x 2 ¾” Bracket
Ø 1 ¼” x Ø 1” End Cap
Foam Roll
Spring Clip
2 ¾” x 2” End Cap
Lock Knob
Crutch Sleeve
3” x 2 ¼” End Cap
1” Square End Cap
2” Arm Curl Stand Sleeve
1 ¾” End Cap
Olympic Sleeve
Foam Roll End Cap
Lock Pin
Ø 1” Bushing
Grip
Abdominal Strap
Strap Buckle
Abdominal Strap Connector
Arm Curl Handle
Arm Curl Bracket
Ø 5/8” Washer
Ø ¾” Washer
Ø 1” Washer
M10 x 2 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M12 x 7 ¼” Hex Bolt
M10 x 2 ½” Allen Bolt
M10 x 5/8” Allen Bolt
11
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
®"
IMPEX Inc. ("IMPEX ) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of two years on the Frame from
the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation
under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line at www.impex-fitness.com
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|