NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
IRON GRIP STRENGTH
WEIGHT BENCH
IGS-705
Warranty
Ordering Parts
Model
IGS-705
Retain This
Manual for
Reference
07-30-08
OWNER'S
MANUAL
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
3. Maximum weight capacity on the uprights: 200 lbs.
4. Maximum user’s weight: 300 lbs.
5. Maximum weight capacity on the leg developer: 100 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WRANING LABEL REPLACEMENT
The warning label shown here have been placed on the Cross Brace. If the label is missing or illegible,
please call customer service at 1-800-888-8899 for replacements. Apply the label in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Pack
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span.
B.) Secure each end of Cross Brace to each Upright Beam with two M10 x 3 1/8” Carriage
Bolts (#26), one Weight Post (#10), two Ø ¾” Washers (#35), and two M10 Aircraft
Nuts (#33).
DIAGRAM 1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Do not tighten the Nuts and Bolts until instructed to do so.
B.) Attach the Main Seat Support (#1) to Cross Brace (#2). Secure it with two M10 x 3 1/8”
Carriage Bolt (#26), one Bracket (#14), two Ø ¾” Washer (#35), and two M10 Aircraft
Nut (#33).
C.) Attach the Leg Developer Holder (#4) to the Main Seat Support. Secure it with three
M10 x 5/8” Allen Bolts (#27) and three Ø ¾” Washers (#35).
D.) Attach the Diagonal Support (#11) to the Main Seat Support and Leg Developer Holder.
Secure each end with one M8 x 5/8” Allen Bolt (#28) and Ø 5/8” Washer (#36).
E.) Securely tighten all Nuts and Bolts.
DIAGRAM 2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#5) to the Leg Developer Holder (#4). Secure it with one
M8 x 2 ¾” Allen Bolt (#29), two Ø 5/8” Washers (#36), and one M8 Aircraft Nut
(#34). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is
able to swivel.
B.) Insert two Foam Tubes (#12) halfway through the holes on Leg Developer. Push
four Foam Rolls (#13) onto the Tubes from each end.
DIAGRAM 3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Sliding Block (#7) to the Main Seat Support (#3). Secure it with one M10
x 4” Hex Bolt (#30), one Ø ¾” Washer (#35), and one M10 Aircraft Nut (#33).
B.) Attach the pivot on the Backrest Support (#9) to the bracket on Main Seat Support.
Secure it with one M10 x 3” Hex Bolt (#31), one Ø ¾” Washer (#35), and one M10
Aircraft Nut (#33).
C.) Insert the Incline Adjustment Frame through the Sliding Block. Use the T-shaped
Lock Pin (#23) to hold the Frame at the selected Incline.
D.) Attach the Incline Adjustment Frame to the Backrest Support. Secure them together
with one M10 x 4” Hex Bolt (#30), Ø ¾” Washer (#35), and one M10 Aircraft Nut
(#33).
DIAGRAM 4
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Step-5 (See Diagram 5)
A.) Attach the Backrest Board (#18) to Backrest Support (#9). Secure it with four M6 x ¾” Hex
Bolts (#38) and four Ø ½” Washers (#37).
B.) Attach the Seat Pad (#39) onto the Main Seat Support (#3). Secure it with four M6 x 1 ¼” Hex
Bolts (#32) and four Ø ½” Washers (#37).
C.) Attach the two Bar Catches (#6) to the two Upright Beams (#1).
DIAGRAM 5
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Upright Beam
Cross Brace
Main Seat Support
Leg Developer Holder
Leg Developer
Bar Catch
2
1
1
1
1
2
1
1
1
2
1
2
4
1
3
4
1
1
1
2
2
4
1
2
12
6
3
2
1
2
1
4
9
1
12
4
8
4
1
Sliding Block
Incline Adjustment Frame
Backrest Support
Weight Post
Diagonal Support
Foam Tube
Foam Roll
Bracket
1 1/8” x 2 3/8” End Cap
Ø ¾” End Cap
2” Square End Cap
Backrest Board
1” x 2” End Cap
¾” x 1 5/8” End Cap
2” Sleeve
Ø 1” End Cap
T-shaped Lock Pin
Bushing
Ø 5/8” End Cap
M10 x 3 1/8” Carriage Bolt
M10 x 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
M8 x 2 ¾” Allen Bolt
M10 x 4” Hex Bolt
M10 x 3” Hex Bolt
M6 x 1 ¼” Hex Bolt
M10 Aircraft Nut
M8 Aircraft Nut
Ø ¾” Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Ø 5/8” Washer
Ø ½” Washer
M6 x ¾” Hex Bolt
Seat Pad
11
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|