NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
EVERLAST
SMITH BENCH
EVE-890
Warranty
Ordering Parts
Model
EVE-890
Retain This
Manual for
Reference
08-16-05
OWNER'S
MANUAL
Made under license from trademark owner Everlast Worldwide
Inc., New York.
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning label shown here has been placed on the Cross Brace. If the label is missing or illegible,
please call customer service at 1-800-888-8899 for replacement. Apply the label in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Note: Do not tighten the nuts and bolts until instructed to do so.
B.) Plug four 2” Stabilizer End Caps (#24) onto the end of the two Stabilizers (#1).
C.) Connect the two Stabilizers (#1) by a Cross Brace (#4) in the mid-span. Align the holes
and secure each end with one 6 ¼” x 2” Bracket (#13), two M10 x 2 ¾” Carriage Bolts
(#18), two ∅ ¾” Washers (#14), and two M10 Aircraft Nuts (#17).
D.) Place an Upright Beam (#3) onto a Stabilizer. Secure it with one 4 ¾” x 2” Bracket (#12),
two M10 x 2 ¾” Carriage Bolts (#18), two Ø ¾” Washers (#14), and two M10 Aircraft Nuts
(#17). Repeat the same step to install the other Upright Beam.
E.) Attach a Rear Support (#2) to a Stabilizer and an Upright Beam. Secure the Support to
the Stabilizer with one 4 ¾” x 2” Bracket (#12), two M10 x 2 ¾” Carriage Bolts (#18), two Ø
¾” Washers (#14), and two M10 Aircraft Nuts (#17). Secure the Support to the Upright
Beam with one M10 x 2 ½” Allen Bolt (#19), two Ø ¾” Washers (#14), and one M10
Aircraft Nut (#17). Repeat the same step to install the other side.
F.) Place a Cross Brace (#4) in between the two Rear Supports (#2). Secure each end with
one Weight Storage Post (#11), two M10 x 2 ¾” Carriage Bolts (#18), two Ø ¾” Washers
(#14), and two M10 Aircraft Nuts (#17). Attach a Spring Clip (#29) to each Weight Post.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Slide both a Rubber Bumper (#26) and Safety Stop (#6) onto a Guide Rod (#5).
B.) Slide a Sliding Bar Catch (#8) onto the Guide Rod.
C.) Insert the bottom of the Guide Rod into the ring cap on the left Stabilizer. Insert the top
of Guide Rod into the ring cap on top of the left Upright Beam. Use the two M8 x ½”
Allen Screws (#16) on the caps to secure the Guide Rod.
D.) Attach a Safety Hook (#7) to the bracket on the Safety Stop. Secure it with one M10 x 1
5/8” Allen Bolt (#20), two Ø ¾” Washers (#14), and one M10 Aircraft Nut (#17).
E.) Attach the Safety Hook to the selected hole on the Upright Beam to obtain the desired
height for safety catch.
F.) Repeat Steps A, B, C, D and E above to install the other side.
G.)Securely tighten all nuts and bolts previously installed.
DIAGRAM 2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) NOTE: Help of another person is strongly recommended for this step. Place the
Lifting Sleeve (#10) in between the two Sliding Bar Catches (#8). Align the holes
and insert the Weight Bar (#9) into the Bar Catch from one end and through the
Lifting Sleeve to the other Bar Catch on the opposite end. Center the Weight Bar
and secure it to each Bar Catch with one M10 x 5/8” Allen Bolt (#15).
B.) Turn the hook on the Lifting Sleeve into the selected holes on the Upright Beams to
secure the Weight Bar position.
C.) Slide a Ø3” Rubber Spacer (#25) onto the Weight Bar. Push one Long Olympic
Sleeve (#27) onto the Weight Bar. Secure the Olympic Sleeve with a M8 x ½” Allen
Screw (#16). Attach a Spring Clip (#29) onto the Sleeve.
D.) Repeat Step C above to install the other side.
E.) Attached the Shoulder Pad (#28) to the Lift Sleeve (#10).
DIAGRAM 3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Plug four Stabilizer End Caps (#24) onto each end of the Front and Rear Stabilizers
(#35 & #36).
B.) Attach the Main Seat Support (#30) to the Rear & Front Stabilizers (#35 & #36).
Secure each end with one 4 ¾” x 2” Bracket (#12), two M10 x 2 ¾” Carriage Bolts
(#18), two Ø ¾” Washers (#14), and two M10 Aircraft Nuts (#17).
DIAGRAM 4
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the side-holes on the Backrest Supports (#33) to the long pivot on the Main
Seat Support (#30). Insert one M10 x 7 ¼” Allen Bolt (#47) through the holes and
secure it with two Ø ¾” Washers (#14), and one M10 Aircraft Nut (#17).
B.) Place the Backrest Incline Support (#34) in between the two Backrest Supports (#33).
Align the holes and secure it with one M10 x 7 ¼” Allen Bolt (#47), two Ø ¾” Washers
(#14), and one M10 Aircraft Nut (#17). Do not tighten the Nuts and Bolts yet. Attach
the other end to a selected slot on the Main Seat Support.
C.) Attach the Seat Incline Support (#42) to the short pivot on the Main Seat Support.
Secure it with a M10 x 4 ¾” Allen Bolt (#48), two Ø ¾” Washers (#14), and one M10
Aircraft Nut (#17).
D.) Attach the Leg Developer (#39) to the open bracket on the Main Seat Support. Secure
it with one M10 x 3 1/8” Allen Bolt (#52), two Ø ¾” Washers (#14) and one M10
Aircraft Nut (#17).
E.) Tighten all Nuts and Bolts previously installed but make sure the Backrest Incline
Support, Backrest Support, Seat Incline Support, and Leg Developer are able to
swivel on the pivots.
DIAGRAM 5
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6)
A.) Place the Backrest Board (#32) onto the Backrest Supports. Secure it with four M6 x 2
1/8” Hex Bolts (#50) and ؽ” Washers (#49).
B.) Place the Seat (#34) onto the Seat Incline Support. Secure it with four M6 x 5/8” Hex
Bolts (#53) and Ø ½” Washers (#49). Insert a L-shaped Pin (#41) to lock the Seat in
desired Incline position.
C.) Insert three Foam Tubes (#37) halfway through the holes on the Leg Developer and
the Main Seat Support. Push six Foam Rolls (#38) onto the Tubes from both ends.
Plug six Foam Roll End Caps (#43) into the Tubes from each end.
D.) Attach the Olympic Sleeve (#55) onto the weight post on the Leg Developer. Secure it
with the M8 x ½” Allen Screw (#16). Attach a Spring Clip (#29) to the Sleeve.
DIAGRAM 6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Stabilizer
Rear Support
Upright Beam
Cross Brace
Guide Rod
Safety Stop
Safety Hook
Sliding Bar Catch
Weight Bar
2
2
2
2
2
2
2
2
1
1
2
6
2
36
2
7
28
20
2
2
2
12
4
8
2
2
2
1
5
1
1
1
2
1
1
1
3
6
1
2
1
1
6
3
4
1
2
1
8
4
2
1
4
1
1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Lifting Sleeve
Weight Storage Post
4 ¾” x 2” Bracket
6 ¼” x 2” Bracket
∅ ¾” Washer
M10 x 5/8” Allen Bolt
M8 x ½” Allen Screw
M10 Aircraft Nut
M10 x 2 ¾” Carriage Bolt
M10 x 2 ½” Allen Bolt
M10 x 1 5/8” Allen Bolt
∅ 2” End Cap
∅ 1 ½” Spacer
1” x 2” End Cap
2” Stabilizer End Cap
∅ 3” Rubber Spacer
∅ 2 ½” x 1” Rubber Bumper
Long Olympic Sleeve
Shoulder Pad
Spring Clip
Main Seat Support
Seat Pad
Backrest Board
Backrest Support
Backrest Incline Support
Rear Stabilizer
Front Stabilizer
Foam Tube
Foam Roll
Leg Developer
Ø 2” End Cap
L-shaped Pin
Seat Incline Support
Foam Roll End Cap
∅ 1” End Cap
¾” x 1 5/8” End Cap
1 ½” Square End Cap
M10 x 7 ¼” Allen Bolt
M10 x 4 ¾” Allen Bolt
∅ ½” Washer
M6 x 2 1/8” Hex Bolt
Leg Developer Bushing
M10 x 3 1/8” Allen Bolt
M6 x 5/8” Hex Bolt
2” Square End Cap
Olympic Sleeve
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|