NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
COMPETITOR BENCH
CB-359
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
CB 359
Retain This
Manual for
Reference
08-06-04
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the Left Upright Beam (#1) and Right Upright Beam (#2) by a Cross Brace
(#3) in the mid-span. Align the holes and secure each end of the Cross Brace with one
4 ¾” x 2” Bracket (#16), two M10 x 3 ½” Carriage Bolts (#33), two ∅ ¾” Washers
(#43), and two M10 Aircraft Nuts (#47).
B.) Place the Backrest Adjustment Bar (#5) in between the two Upright Beams on the
selected bar holder to obtain desired incline of Backrest Board.
C.) Insert two Crutches (#7) into the top openings on the Upright Beams. Push down the
Plastic Sleeve (#31) until it locks in place. Secure the Crutches with two Lock Knobs
(#30) through selected holes to obtain desired height of the Supports.
DIAGRAM 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Main Stabilizer (#13) to the Cross Brace (#3). Secure it with a 4 3/8” x 1 ½”
Bracket (#15), two M10 x 2 1/8” Carriage Bolts (#35), ∅ ¾” Washers (#43), and M10
Aircraft Nuts (#47).
B.) Attach the Front Support (#10) to the Main Stabilizer (#13). Secure it with one M10 x 2
3/8” Allen Bolt (#38) and ∅ ¾” Washer (#43).
C.) Attach one end of Man Seat Support (#4) to the Main Stabilizer (#13). Secure it with two
M10 x 2 ½” Carriage Bolts (#34), ∅ ¾” Washers (#43), and M10 Aircraft Nuts (#47).
D.) Attach the other end of Main Seat Support (#4) to the Front Support (#10). Secure it
with two M10 x 1” Carriage Bolts (#36), ∅ ¾” Washers (#43), and M10 Aircraft Nuts
(#47).
DIAGRAM 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the hole-side of Backrest Supports (#9) to the pivot on the Main Seat Support
(#4). Secure it with one M12 x 6” Hex Bolt (#40), two Ø1” Washers (#42), and one
M12 Aircraft Nut (#46). Place the other end of Backrest Supports rest against the
Backrest Adjustment Bar.
B.) Place the Backrest Board (#17) onto the Backrest Supports (#9). Secure it with four
M6 x 1 3/8” Hex Bolts (#41) and ∅½” Washers (#45).
C.) Place the Seat (#18) onto the Main Seat Support (#4). Secure it with four M6 x 1 3/8”
Hex Bolts (#41) and ∅ ½” Washers (#45).
DIAGRAM 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#6) to the open bracket on the Front Support (#10).
Secure it with one M10 x 2 7/8” Allen Bolt (#37), two ∅ ¾” Washers (#43), and one
M10 Aircraft Nut (#47). Do not over tighten the Nut and Bolt. Make sure the Leg
Developer is able to swivel.
B.) Insert two Foam Tubes (#8) halfway through the holes on the Leg Developer. Push
four Foam Rolls (#20) onto the Foam Tubes.
C.) Attach the Bar Holder (#12) to the Leg Developer (#6). Secure it with a L-shaped
Pin (#48). Remove the Bracket when using the Leg Developer.
D.) Attach the Arm Curl Pad (#19) to the Arm Curl Stand (#11) then secure it with two
M8 x 5/8” Allen Bolts (#39) and two ∅ 5/8” Washers (#44).
E.) Insert the Arm Curl Stand (#11) into the top opening on the Front Support (#10).
Secure it with a Lock Knob (#30). Use the Lock Knob to select the Arm Curl height.
F.) Attach a Spring Clip (#49) to the weight post on the Leg Developer. Attach two
Spring Clips (#49) to the Curl Bar (#14).
DIAGRAM 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Left Upright Beam
Right Upright Beam
Cross Brace
Main Seat Support
Backrest Adjustment Bar
Leg Developer
Crutch
Foam Tube
Backrest Support
Front Support
Arm Curl Stand
Bar Holder
Main Stabilizer
Curl Bar
4 3/8” x 1 ½” Bracket
4 ¾” x 2” Bracket
Backrest Board
Seat
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
2
1
1
1
4
2
2
2
1
3
4
4
1
2
3
2
2
4
2
2
2
1
1
2
1
8
2
13
2
8
1
11
1
3
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Arm Curl Pad
Foam
1 ¾” Square End Cap
1 ½” Square End Cap
1” Square End Cap
∅ 1” End Cap
∅ 1” Cone-shape End Cap
∅ ¾” Cone-shape End Cap
2 ¾” x 2” End Cap
1 ¾” x 1 ½” Sleeve
Plastic Bushing
Lock Knob
3” x 2 ¼” Sleeve
Crutch End Cap
M10 x 3 ½” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M10 x 2 1/8” Carriage Bolt
M10 x 1” Carriage Bolt
M10 x 2 7/8” Allen Bolt
M10 x 2 3/8” Allen Bolt
M8 x 5/8” Allen Bolt
M12 x 6” Hex Bolt
M6 x 1 3/8” Hex Bolt
Ø 1” Washer
Ø ¾” Washer
Ø 5/8” Washer
Ø ½” Washer
M12 Aircraft Nut
M10 Aircraft Nut
L-shaped Pin
Spring Clip
Philips Screw
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|