NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY HOME GYM
MWM-1100
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-1100
Retain This
Manual for
Reference
08-10-09
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Do not intend to insert weight selector pin while the weight stack or top plate
is in elevated position.
14. Be certain the weight Selector Pin is completely inserted.
15. Never use dumbbells or other means to increase the weight resistance. Use only weight
plates provided by manufacturer.
16. This machine is designed and intended for home and consumer use only, not for
commercial use.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels
are missing or illegible, please call customer service at 1-800-999-8899 for replacements. Apply the labels
in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches and
Allen Wrenches. NOTE: It is strongly recommended that this machine to be
assembled by two or more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Slide two Ø 2 ½” x 1” Rubber Bumpers (#35) onto the two Guide Rods (#5). Insert
the two Guide Rods into the holes on the Rear Stabilizer (#2). Secure each Guide
Rod with one M10 x 1” Allen Bolt (#62) and one ∅ ¾” Washer (#70) from the
bottom.
B.) Do not tighten Nuts and Bolts starting from this step until instructed to do
so.
C.) Attach the rear of Main Base Frame (#1) to the Rear Stabilizer. Secure them with
two M10 x 2 ½” Carriage Bolts (#60), one 4 3/8” x 1 ¾” Bracket (#22), two Ø ¾”
Washers (#70), and two M10 Aircraft Nuts (#72).
D.) Attach the Vertical Frame (#3) onto the Main Base Frame. Secure them with two
M10 x 2 ½” Carriage Bolts (#60), one 4 3/8” x 1 ¾” Bracket (#22), two Ø ¾”
Washers (#70), and two M10 Aircraft Nuts (#72).
DIAGRAM 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Slide 9 Weight Plates (#50) onto the Guide Rods (#5). Make sure the deep groove on the
Weight Plate are facing down and toward the back of the Machine.
B.) Align the holes on the Weight Plates. Insert a Selector Rod (#16) through the center hole.
Use the L-shaped Pin (#57) to select the number of Weight Plates for exercise. Each Plate
weighted approx. 10lbs. Please refer to the Weight Resistance Chart in page 21.
C.) Slide Selector Stem (#49) down the Guide Rods.
D.) Attach the holes on the Upper Frame (#4) onto the Guide Rods. Place the Upper Frame
onto the Vertical Frame (#3).
E.) Secure the Upper Frame to the Guide Rods with two M10 x 1” Allen Bolts (#62) and two Ø
¾” Washers (#70).
F.) Secure the Upper Frame to the Vertical Frame with two M10 x 2 ½” Carriage Bolts (#60),
one 4 3/8” x 1 ¾” Bracket (#22), two ∅ ¾” Washers (#70), and two M10 Aircraft Nuts (#72).
G.)Securely tighten all Nuts and Bolts installed in Step-1 and Step-2.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Seat Support (#9) to the Vertical Frame (#3). Secure it with two M10 x 2 ½”
Carriage Bolts (#60), one 5 1/8” x 1 5/8” Bracket (#21), two Ø ¾” Washers (#70), and two
M10 Aircraft Nuts (#72).
B.) Place the Seat Pad (#25) onto the Seat Support. Secure it with two M8 x 2 3/8” Allen Bolts
(#68) and two Ø 5/8” Washers (#69).
C.) Attach two ∅ ¾” Leg Developer Bushings (#54) to the Leg Developer (#9). Attach the Leg
Developer to the bracket on the Seat Support. Secure it with one M10 x 3 1/8” Allen Bolt
(#67), two Ø ¾” Washers (#70), and one M10 Aircraft Nut (#72). Do not over tighten the
Bolt and Nut. Make sure the Leg Developer is able to swivel freely on the Bolt.
D.) Insert two Foam Tubes (#15) halfway through the holes on the Seat Support and Leg
Developer. Push four Foam Rolls (#33) onto the Tubes from both ends. Cover each end
with a Foam Roll End Cap (#48).
DIAGRAM 3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach two Ø 1” x Ø ½” Bushings (#53) to the holes on Upper Frame (#4). Attach the Front
Press Base (#6) to the two Bushings. Secure it with one M12 x 3 3/8” Hex Bolt (#61), two Ø
1” Washers (#71), and one M12 Aircraft Nut (#73). Do not over tighten the Nut and Bolt.
B.) Insert the axle on the Right Butterfly (#8) through the hole on the Front Press Base from the
bottom. Slide a Lock Ring (#41) onto the axle. Align the holes and secure it with one M6 x 1
3/8” Allen Bolt (#58) and one M6 Aircraft Nut (#23).
C.) Slide the Butterfly Large Foam Roll (#32) onto the Right Butterfly.
D.) Insert a Front Press Handle (#11) to Right Butterfly. Secure it with one M10 x 1” Allen Bolt
(#62) and one Ø ¾” Washer (#70).
E.) Repeat the same step B to D install the Left Butterfly (#7).
F.) Attach the Swivel Pulley Bracket Frame (#19) to the back of the Vertical Frame (#3). Secure
it with one M10 x 3 ½” Allen Bolt (#66), two Ø ¾” Washers (#70), and one M10 Aircraft Nut
(#72).
G.)Attach a Swivel Pulley Bracket (#17) to each end of Swivel Pulley Bracket Frame (#19).
Secure each Bracket with one M10 x 2 ½” Allen Bolt (#65), two Ø ¾” Washers (#70), and
one M10 Aircraft Nut (#72).
H.) Attach the Backrest Board (#24) to the Vertical Frame. Secure it with two M8 x 2 3/8” Allen
Bolts (#68) and two Ø 5/8” Washers (#69).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 4
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 136” Upper Cable (#26) to the front opening on the Upper Frame (#4).
NOTE: The Ball Stopper on the Cable needs to be underneath the Frame.
B.) Attach a Pulley (#38) to the forward most opening. Secure it with one M10 x 2 3/8”
Allen Bolt (#64), two Ø 1” x ½” Pulley Bushings (#39), and one M10 Aircraft Nut
(#72).
C.) Draw the Cable towards the back of the machine to the second opening on the
Upper Frame. Repeat Step B above to install a Pulley.
D.) Draw the Cable around the Pulley then pull back to the open bracket on the back
of Front Press Base (#6).
E.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#63), two
Ø ¾” Washers (#70), and one M10 Aircraft Nut (#72).
F.) Draw the Cable around the Pulley then to the opening on the Vertical Frame (#3).
Repeat Step B to install a Pulley.
G.) Draw the Cable over the Pulley and pull the Cable downwards. Attach a Pulley to
the upper holes on the two Double Floating Pulley Brackets (#20). Repeat Step E
above to install the Pulley. Attach a Pulley to a selected lower hole and repeat
Step E to install this Pulley. Let the Brackets hanging just for now.
H.) Draw the Cable around the Pulley then pull upwards to the open bracket
underneath the Upper Frame. Repeat Step E to install another Pulley.
I.) Pull the Cable downwards between the two Guide Rods to the Selector Rod (#16).
Securely thread the bolt on the end of the Cable into the Selector Rod.
J.) Attach an 8-link Chain (#30) to the Cable using a C-clip (#31). Attach the Lat Bar
(#13) to the Chain using a C-clip. Adjust the length of Chain to obtain the desired
Lat Bar exercise.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
DIAGRAM 5
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 108” Butterfly Cable (#27) to the hook on the Right Butterfly (#8). Draw
the Cable towards the right open Swivel Pulley Bracket (#17).
B.) Attach a Pulley (#38) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#63), two ∅ ¾”
Washers (#70), and one M10 Aircraft Nut (#72).
C.) Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double
Floating Pulley Bracket (#18). Install a Pulley as described in Step B. Let the Bracket hang for
now.
D.) Draw the Cable around the Pulley and pull upward to the left open Swivel Pulley Bracket.
Install another Pulley as described in Step B above.
E.) Draw the Cable over the Pulley and attach the end to the open hook on the Left Butterfly (#7).
DIAGRAM -6
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the 142” Lower Cable (#28) to the opening on the bottom of the Leg
Developer (#10).
B.) Attach a Pulley (#38) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt
(#64), two ∅ 1” x ½” Pulley Bushings (#39), and one M10 Aircraft Nut (#72).
C.) Draw the Cable underneath the Pulley towards the back of the machine to the
opening on the bottom of Vertical Frame (#3).
D.) Repeat Step B to install a Pulley.
E.) Pull the Cable upward to the Angled Double Floating Pulley Brackets (#18)
previously installed in Step-6.
F.) Attach a Pulley to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#63),
two Ø ¾” Washers (#70), and one M10 Aircraft Nut (#72).
G.) Draw the Cable around the Pulley then pull downward to the open bracket on the
Main Base Frame (#1). Repeat Step F to install a Pulley.
H.) Draw the Cable around the Pulley then pull upward to the Pulley on Double
Floating Pulley Bracket (#20) previously installed in Step-5.
I.) Draw the Cable around the Pulley then pull downward to the bracket on the rear
of Vertical Frame. Secure the other end of the Chain to the bracket with a M10 x
1” Allen Bolt (#62), two ∅ ¾” Washers (#70) and one M10 Aircraft Nut (#72).
J.) Adjust the tension of the Cable System by adjusting the position of the Pulley on
the bottom half of the hanging bracket (multi-holes). If the Cables are too loose
then move the Pulley up one hole on the Double Floating Pulley Bracket. If the
cable tension is too tight, move the pulley down one hole on the bracket.
K.) Attach the 15-link Chain (#29) to the end of the Cable by using a C-clip (#31).
Attach the Arm Curl Handle (#14) to the Chain by using another C-clip. Replace
Arm Curl Handle with the Ankle Strap (#51) or Single Handle (#52) for various
exercises. Adjust the length of Chain to obtain the desired exercise. Remove the
Arm Curl Handle, Ankle Strap, or Single Handle when using the Leg Developer.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 7
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Main Base Frame
Rear Stabilizer
Vertical Frame
Upper Frame
Guide Rod
Front Press Base
Left Butterfly
Right Butterfly
Seat Support
Leg Developer
Front Press Handle
Rotate Ring
Lat Bar
Arm Curl Handle
Foam Tube
Selector Rod
Swivel Pulley Bracket
Angled Floating Pulley Bracket
Swivel Pulley Bracket Frame
Double Floating Pulley Bracket
5 1/8“ x 1 5/8“ Bracket
4 3/8“ x 1 ¾“ Bracket
M6 Aircraft Nut
Backrest Board
Seat Pad
136” Upper Cable
108” Butterfly Cable
142” Lower Cable
15-link Chain
8-link Chain
C-clip
Butterfly Large Foam Roll
Foam Roll
Front Press Handle Grip
Ø 2 ½” x 1” Rubber Bumper
Ø 1 ½” x 5/8” Rubber Bumper
Ø 1 ¾” x 1 5/8” Rubber Bumper
Pulley
Ø 1” x ½” Pulley Bushing
Ø 1 1/8” x 3 1/4” Sleeve
Lock Ring
2” Square End Cap
1 ¾” Square End Cap
1 5/8” x 2 3/8” End Cap
Ø 1 ½” End Cap
Ø 1” End Cap
Ø 1” Cone-shaped End Cap
Foam Roll End Cap
Selector Stem
1
1
1
1
2
1
1
1
1
1
2
2
1
1
2
1
2
1
1
2
1
3
2
1
1
1
1
1
1
1
4
2
4
2
2
1
1
14
10
2
2
2
6
3
4
4
1
4
1
9
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
Ankle Strap
Single Handle
Ø 1” x Ø ½” Bushing
Ø ¾” Leg Developer Bushing
Plastic Ring
1
1
2
2
4
4
1
2
2
8
1
7
9
5
2
1
1
4
4
42
2
27
1
1
1
Rivet
L-shaped Pin
M6 x 1 3/8” Allen Bolt
M6 x 5/8” Philips Screw
M10 x 2 ½” Carriage Bolt
M12 x 3 3/8” Hex Bolt
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 2 ¾” Allen Bolt
M10 x 3 1/8” Allen Bolt
M8 x 2 3/8” Allen Bolt
Ø 5/8“ Washer
Ø ¾“ Washer
Ø 1” Washer
M10 Aircraft Nut
M12 Aircraft Nut
#5 Allen Wrench (Tool)
#6 Allen Wrench (Tool)
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Weight Plate
20
Download from Www.Somanuals.com. All Manuals Search And Download.
WEIGHT RESISTANCE CHART
STATION
FRONT PRESS
BUTTERFLY
1
2
3
4
5
6
7
8
9
30 42 54 66 78 90 102 114 126
15 20 25 30 35 40 45 50 55
30 40 50 60 70 80 90 100 110
30 40 50 60 70 80 90 100 110
30 40 50 60 70 80 90 100 110
LAT PULL
LOW PULLEY
LEG DEVELOPER
Note: Each plate weights 10 lbs.
Numbers are approximate. Actual weights may vary.
Values for Butterfly are for each arm.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® Inc.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of one year on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to
replacing or repairing, at IMPEX's option.
All returns must be pre-authorised by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused by
or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an
TFG authorised service center or for products used for commercial or rental purposes. No other warranty
beyond that specifically set forth above is authorised by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein.
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9am – 5pm.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|