NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY DIAMOND ELITE
OLYMPIC BENCH
Hardware Identifier
Assembly Instruction
Parts List
MD-857
Warranty
Ordering Parts
Model
MD-857
Retain This
Manual for
Reference
08-05-09
OWNER'S
MANUAL
IMPEX® INC.
2801 S. Towne Ave., Pomona, CA 91766
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
3. Maximum on Bar Catch: 300 lbs
4. Maximum weight on Leg Developer: 100 lbs
5. Maximum user weights: 300 lbs
4. Maximum weight capacity 600 lbs (include user’s weight).
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL PLACEMENT
The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible,
please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten all nuts and bolts until instructed to do so.
B.) Attach the Left Upright Beam (#1) to a Rear Stabilizer (#3). Secure it with two M10 x 5/8” Allen
Bolts (#63), and two Ø ¾” Washers (#66).
C.)Attach the bottom of the Rear Diagonal Support (#8) to the Rear Stabilizer. Secure it with one
M10 x 3 ¾” Allen Bolt (#60), two Ø ¾” Washers (#66), and one M10 Aircraft Nut (#68). Attach
the top of the Rear Diagonal Support (#8) to the Left Upright Beam (#1). Secure it with two
M10 x 5/8” Allen Bolts (#63) and Ø ¾” Washers (#66).
D.)Repeat Steps A, B, and C above to install the Right side.
E.) Connect the Left & Right Upright Beams with a Cross Brace (#5) in the mid-span. Secure each
end of Cross Brace with two M10 x 3 ½” Carriage Bolts (#56), one 4 ¾” x 2” Bracket (#23), two
Ø ¾” Washer (#66), and two M10 Aircraft Nut (#68). Place the Backrest Adjustment Bar (#6)
onto the selected slot between the Upright Beams.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Leg Developer Support (#13) to the Front Stabilizer (#14). Secure it with three
M10 x 5/8” Allen Bolts (#63) and ¾” Washers (#66).
C.)Slide the Sliding Block (#15) onto the Main Seat Support (#4). Thread a M18 Lock Knob
(#42) into the selected hole to hold the Sliding Block in position.
D.)Attach the Main Seat Support (#4) to the Leg Developer Support (#13). Secure it with one
M10 x 2 ½” Carriage Bolt (#58) from the top, two M10 x 2 ¾” Carriage Bolts (#57) from the
side, three ¾” Washers (#66) and three M10 Aircraft Nuts (#68).
E.) Attach the Main Seat Support (#4) to the Cross Brace (#5). Secure it with two M10 x 2 3/8”
Carriage Bolts (#59), one 4 ¾” x 2” Bracket (#23), two ¾” Washers (#66), and two M10
Aircraft Nuts (#68).
F.) Securely tighten all Nuts and Bolts installed in Step-1 and Step-2.
G.)Attach the two Squat Bar Catches (#7) to the back of the two Upright Beams. Secure each
Catch with a 4 ½” L-shaped Pin (#51).
H.)Insert a Weight Post (#24) into the hole on the Rear Diagonal Support (#8). Secure it with
one M10 x ¾” Allen Bolt (#62) and Ø ¾” Washer (#66). Slide an Olympic Sleeve (#30) onto
the Weight Post. Repeat for the other side.
I.) Insert the Left & Right Bar Catches (#16 ), Left & Right Safety Catches (#18 )
into the selected holes on the Upright Beams (#1 & #2).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the holes on the end of the Backrest Supports (#21) to the long pivot on the Sliding
Block (#15). Attach the Backrest Board (#26) to the Backrest Supports. Secure it with
four M8 x 1 5/8” Allen Bolts (#65) and Ø5/8” Washers (#67). Place the Backrest Board
against the Backrest Adjustment Bar.
B.) Attach the Seat Bracket (#20) to the short pivot on the Sliding Block. Secure it with one
M10 x 4 ¾” Allen Bolt (#61), two Ø ¾” Washers (#66), and one M10 Aircraft Nut (#68).
C.) Place the Seat Pad (#27) onto the Seat Bracket. Secure it with four M8 x 5/8” Allen Bolts
(#64) and Ø 5/8” Washers (#67).
D.) Insert a 4” L-shaped Pin (#53) into the selected hole on the Seat Bracket to obtain the
desired Seat inclined position.
DIAGRAM 3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Insert the U-shaped Pin (#49) into the open slot on the Leg Developer Support (#13).
Secure it with one M6 x ½” Philips Screw (#47), Ø ½” Washer (#48), and Spring (#50).
B.) Attach the Leg Developer (#10) to the Leg Developer Support. Secure it with an Axle (#55),
two M10 x 5/8” Allen Bolts (#63) and two ¾” Washers (#66).
C.)Insert one Foam Tube (#22) halfway through the hole on the Leg Developer Holder. Insert
two Foam Tubes halfway through the holes on the Leg Developer. Push six Foam Rolls
(#31) onto the Tubes from both ends. Plug six Foam Roll End Caps (#32) into the ends.
D.)Slide an Olympic Sleeve (#30) onto the weight post on the Leg Developer. Attach a Spring
Clip (#54) to the Sleeve.
DIAGRAM 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Arm Curl Pad (#28) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8”
Allen Bolts (#64) and Ø 5/8” Washers (#67).
B.) Insert the Arm Curl Stand into the top opening on the Leg Developer Support. Use a M18
Lock Knob (#42) to secure the Stand.
C.)Attach the Curl Bar Handle Support (#11) to the bracket on the Leg Developer (#10).
Secure it with a 3 7/8” Lock Pin (#52). The Leg Developer can be locked when doing Sit Up
exercises. Simply pull the U-shaped Pin out and drop into the hole on the Leg Developer.
Remove the Pin when doing Leg Developer exercises.
D.)Remove the Arm Curl Stand and the Curl Bar Handle when using the Leg Developer.
DIAGRAM 5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Left Upright Beam
Right Upright Beam
Rear Stabilizer
Main Seat Support
Cross Brace
Backrest Adjustment Bar
Squat Bar Catch
Rear Diagonal Support
Arm Curl Stand
Leg Developer
Curl Bar Handle Support
Curl Bar Handle
Leg Developer Support
Front Stabilizer
Sliding Block
1
1
2
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
3
3
2
2
1
1
1
14
3
6
6
2
2
6
2
1
8
2
2
1
2
2
2
2
2
1
1
1
1
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
4 ½” L-shaped Pin
3 7/8” Lock Pin
4” L-shaped Pin
Spring Clip
Axle
M10 x 3 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
M10 x 3 ¾” Allen Bolt
M10 x 4 ¾” Allen Bolt
M10 x ¾” Allen Bolt
M10 x 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
M8 x 1 5/8” Allen Bolt
Ø ¾” Washer
2
1
1
1
1
4
2
1
2
2
1
2
13
6
4
30
10
12
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Left Bar Catch
Right Bar Catch
Left Safety Catch
Right Safety Catch
Seat Bracket
Backrest Support
Foam Tube
4 ¾” x 2” Bracket
Weight Post
Panel
Backrest Board
Seat Pad
Arm Curl Pad
Rivet
Olympic Sleeve
Foam Roll
Foam Roll End Cap
1 5/8” x 2 3/8” End Cap
2” Square End Cap
2 ¾” x 2” End Cap
1” Square End Cap
1 5/8” x ¾” End Cap
Ø 1” End Cap
Ø 2 3/8” Bushing
2 3/8” x 2” Sleeve
2” x 1 ¾” Sleeve
M18 Lock Knob
Rubber Bumper
Ø 1 ½” Plastic Ring
Ø ½” Bushing
Ø 5/8” Washer
M10 Aircraft Nut
Curl Bar Handle Grip
M6 x ½” Philips Screw
Ø ½” Washer
U-shaped Pin
Spring
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of two years on the Frame from
the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation
under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage. No other warranty beyond that specifically set forth above is authorized by
IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do
not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the
above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from
state to state. Register on-line at www.impex-fitness.com
IMPEX® INC.
2801 S. Towne Ave.
Pomona, CA 91766
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-
800-999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm
Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|