Model No. IMTL39105.0
Serial No.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-800-753-4645
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
TROUBLESHOOTING on page 17 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 275 pounds. Never allow
more than one person on the treadmill at a time.
16. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the circuit breaker.)
9. When connecting the power cord (see page 10),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 16.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
10. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 10. To purchase a surge suppressor, see
your local IMAGE dealer or call the toll-free
telephone number on the front cover of this
manual and order part number 146148, or see
your local electronics store.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Inspect and properly tighten all parts of the
treadmill every three months.
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
21. Never drop or insert any object into any open-
ing.
22.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
23. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on your treadmill. If a decal is missing, or
if it is not legible, please call the toll-free telephone number on the front cover of
this manual and order a free replacement decal. Note: The decals are not shown at
actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new IMAGE® 15.0 R tread-
mill. The IMAGE 15.0 R treadmill offers a selection of
features designed to make your workouts at home
more enjoyable and effective. And when you’re not ex-
ercising, the unique IMAGE 15.0 R treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
number and serial number before calling. The model
number of the treadmill is IMTL.39105.0. The serial
number can be found on a decal attached to the tread-
mill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Accessory Tray
Console
Key/Clip
Handrail
Upright
Storage Latch
Reset/Off
Circuit Breaker
Power Cord
Walking Belt
Foot Rail
RIGHT SIDE
Cushioned Walking Platform
for maximum exercise comfort
BACK
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own Phillips screwdriver
and needlenose pliers
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
For help identifying assembly hardware, see the drawings below.
Silver Ground Screw
(75)–1
2” Bolt (64)–2
5/16” Star
Wheel Nut (32)–2
3/4” Screw (2)–6
Washer (97)–6
1/2” Screw (48)–6
3” Bolt (37)–6
1” Tek Screw (39)–4
4” Bolt (98)–2
1. Make sure that the power cord is unplugged.
1
86
With the help of a second person, carefully tip the tread-
mill onto its left side as shown. Partially fold the Frame
(86) so that the treadmill is more stable. IMPORTANT:
Do not fully fold the treadmill until it is completely
assembled.
57
64
57
39
Attach four Base Pads (57) (only three shown) to the
bottom of the Base (69) with four 1” Tek Screws (39).
66
32
69
39
Attach a Wheel (66) to the Base (69) with a 2” Bolt (64)
and a Wheel Nut (32) as shown. Do not overtighten the
Wheel Nut; the Wheel should turn freely.
57
39
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Identify the Right Upright (9) and the Left Upright (61).
2
42
Straighten the Upright Wire (42), and feed it into the lower
end of the Right Upright (9) and out of the upper end.
Next, hold the Right Upright against the right side of the
Base (69); make sure that the Right Upright is turned
so that the upper end is angled in the direction
shown. Hand tighten two 3” Bolts (37) with two 5/16” Star
Washers (97) into the Base and the Right Upright; be
careful not to damage the Upright Wire. Do not
tighten the Bolts yet.
9
69
97
Small
Holes
37
With the help of a second person, carefully tip the tread-
mill onto its other side. Attach the other Wheel (not
shown) as described in step 1, and then attach the Left
Upright (61) as described above. Make sure that the
two small holes in the Left Upright are in the posi-
tion shown. Note: There is not an upright wire on the
left side.
61
72
3. With the help of a second person, carefully tip the tread-
mill back to the upright position.
3
71
Identify the Right Handrail (72), which has a large hole in
the left side. Feed the Upright Wire (42) into the hole in
the bottom of the Right Handrail and out of the large hole
in the side. Note: It may be helpful to use needlenose pli-
ers to pull the Upright Wire out of the hole.
37
42
Hole
37
Hole
9
Attach the upper end of the Right Handrail (72) to the
Right Upright (9) with a 3” Bolt (37); do not tighten the
Bolt yet. Attach the lower end of the Right Handrail with
a 4” Bolt (98) and a 5/16” Star Washer (97). Then,
tighten the 3” Bolt and the 4” Bolt.
61
98
Attach the Left Handrail (71) in the same way. Note:
There is not a wire harness on the left side.
97
98
97
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Hold the Console Base (47) near the Left Handrail (71).
Attach the end of the ground wire on the Console Base
to the indicated small hole in the Left Handrail with the
Silver Ground Screw (75).
4
Ground
Wire
47
Small
Hole
75
71
5. Touch the Right Handrail (72) to discharge any static.
Slide the sleeve off the connector on the Upright Wire
(42) as shown in the inset drawing. Next, press the end of
the Upright Wire into the socket in the bottom of the
Console Base (47). The connector should slide easily
into the socket and snap into place. If the connector
does not slide easily and snap into place, turn the connec-
tor and then insert it. Then, slide the sleeve back over the
connector.
5
72
47
42
Connector
Sleeve
42
6. Set the Console Base (47) on the Handrails ( 71, 72).
Attach the Console Base with four 3/4” Screws (2). Start
all four Screws before tightening them; do not over-
tighten the Screws.
6
47
71
72
See the lower drawing. Make sure that the Upright Wire
(42) is routed below the two indicated round posts (A).
Next, press the Upright Wire into the slot between the
square post (B) and the Console Base (47).
2
2
A
B
42
47
8
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Cover the Upright Wire (42) with the Right Grip Plate
(36). Be careful not to pinch the Upright Wire. Tighten
three 1/2” Screws (48) into the Right Grip Plate and the
Console Base.
7
47
Ground
Wire
Attach the Left Grip Plate (34) over the ground wire and
the other wires with three 1/2” Screws (48). Be careful
not to pinch any of the wires.
42
36
34
48
48
8. Lower the Uprights (9, 61) until the handrails are touch-
ing the floor.
8
See the lower drawing. Position the Uprights (9, 61) so
that the treadmill Frame (86) is centered between them.
See the upper drawing. Firmly tighten the four 3” Bolts
(37). Then, raise the Uprights (9, 61) back to the vertical
position.
Handrail
37
9, 61
Top View
61
9
9
86
9. Attach the Storage Latch (29) and the Latch Spacer (44)
to the Left Upright (61) with two 3/4” Screws (2) as shown.
Do not overtighten the Screws.
61
29
44
2
10. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking
belt (see page 18). To protect the floor or carpet, place a mat under the treadmill.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local IMAGE dealer or call the toll-free tele-
phone number on the front cover of this manual
and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Note: If there are thin sheets of plastic
on the console, remove the plastic.
Key
Clip
FEATURES OF THE CONSOLE
Preset Programs
The console also features four preset programs. Each
program automatically controls the speed and incline
of the treadmill as it guides you through an effective
workout.
The treadmill console offers a selection of features
designed to make your workouts more effective. When
the manual mode of the console is selected, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
To use the manual mode of the console, follow the
steps beginning on page 12. To use the MyTracks™
StepCounter program, see page 13. To use a preset
program, see page 14.
MyTracks™ StepCounter
Walking is one of the most popular exercises world-
wide. Walking does not require advanced conditioning
or special skills, yet it produces numerous benefits,
such as increased calorie burning, a slimmer waist,
toned muscles, enhanced energy and stamina, lower
blood pressure, and reduced stress.
HOW TO TURN ON THE POWER
Plug in the power cord (see
page 10). Next, locate the
reset/off circuit breaker lo-
cated on the treadmill frame
near the power cord. Make
sure that the circuit breaker
is in the “reset” position.
Reset
To track your walking exercise, the console features a
new MyTracks™ StepCounter that counts the number
of steps that you take during each workout. In addition,
the console offers a MyTracks™ StepCounter program
that allows you to enter the number of steps that you
plan to walk, and counts down the steps as you
exercise.
Next, stand on the foot rails of the treadmill. Locate the
clip attached to the key (see the drawing above), and
slide the clip securely onto the waistband of your
clothes. Then, insert the key into the console. After a
moment, the displays will light. Test the clip by care-
fully taking a few steps backward until the key is
pulled from the console. If the key is not pulled
from the console, adjust the position of the clip.
More reliable than conventional pedometers, the
MyTracks™ StepCounter is highly accurate with most
users. For the best results, try to maintain a steady
pace, a uniform stride length, and a consistent position
on the treadmill as you walk. Lighter users may also
find it helpful to reduce the incline of the treadmill or to
increase the speed of the walking belt.
Note: To prevent damage to the walking platform,
always wear clean shoes when using the treadmill.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Change the incline of the treadmill as desired.
HOW TO USE THE MANUAL MODE
4
5
To change the incline of the treadmill, press the
Incline increase and decrease buttons. Each time
a button is pressed, the incline setting will change
by 0.5%; if a button is held down, the incline set-
ting will change quickly.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
11.
Follow your progress with the three displays.
Select the manual mode.
2
The left display—This
When the key is in-
display will show the
serted, the manual
speed of the walking
mode will be selected.
belt, the incline level of
If a program has been
the treadmill, and the
selected, press the
approximate number of
Program button repeat-
edly until the right display shows a time of 0:00.
calories you have burned during your workout.
The display will change from one number to the
next every few seconds. This display will also
show your heart rate when you use the pulse sen-
sor (see step 6 on page 13).
Start the walking belt.
3
To start the walking belt, press the Start button,
the Speed increase button, or one of the buttons
numbered 1 through 10.
The MyTracks™
StepCounter
display—When the
manual mode or a
preset program is
selected, this display
If the Start button or
the Speed increase
button is pressed, the
walking belt will begin
will show the number of steps you have walked or
run during your workout. When the MyTracks™
StepCounter program is selected, this display will
show the number of steps still to be taken.
to move at 1 mph. As
you exercise, change
the speed of the walking belt as desired by press-
ing the Speed increase and decrease buttons.
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph.
Note: For the treadmill to count your steps accu-
rately, correct walking form is important. As you
walk, try to maintain a steady pace, a uniform
stride length, and a consistent position on the
treadmill. Lighter users may also find it helpful to
reduce the incline of the treadmill or to increase
the speed of the walking belt. IMPORTANT:
Always walk at a speed that is comfortable for
you.
If one of the ten numbered buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting. Note: The
console can display speed and distance in ei-
ther miles or kilometers (see THE INFORMA-
TION MODE on page 15). For simplicity, all in-
structions in this section refer to miles.
The right display—
This display will show
the elapsed time, the
distance that you have
walked or run during
your workout, and your
pace (pace is shown in minutes per mile). Note:
When a preset program is selected, the right dis-
play will show the time remaining in the program
instead of the elapsed time.
To stop the walking belt, press the Stop button.
The time will begin to flash in the right display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the ten num-
bered buttons.
Note: The first time you use the treadmill, periodi-
cally inspect the alignment of the walking belt, and
align it if necessary (see page 18).
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Measure your heart rate if desired.
HOW TO USE THE MYTRACKS™
STEPCOUNTER PROGRAM
6
To measure
your heart rate,
stand on the
foot rails and
place your left
thumb on the
pulse sensor.
Do not press
too hard, or
Pulse Sensor
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
11.
Select the MyTracks™ StepCounter program.
2
the circulation in your thumb will be restricted
and your pulse will not be detected. When your
pulse is detected, a heart-shaped indicator in the
left display will flash each time your heart beats,
and then your heart rate will be shown. For the
most accurate heart rate reading, hold your
thumb on the pulse sensor for 15 seconds.
Press the 10,000 Steps
Program button; a goal
of 10,000 steps will ap-
pear in the MyTracks™
StepCounter display.
Note: If the walking belt
is moving when the 10,000 Steps Program button
is pressed, the walking belt will slow to a stop.
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb off the pulse sensor for a few seconds.
Then, reposition your thumb on the pulse sensor.
Remember to stand still while measuring your
heart rate.
Depending on your fitness level, you may desire
to walk fewer than or more than 10,000 steps. To
change the goal, press the increase and decrease
buttons beside the 10,000 Steps Program button.
Each time a button is pressed, the goal will change
by 500 steps. Note: The goal can be changed
either before or after the program is started.
Turn on the workout fan if desired.
7
8
To turn on the workout fan at low, medium, or high
speed, press the Workout Fan button once, twice,
or three times. To turn off the fan, press the button
a fourth time. Note: If the fan is left on when the
walking belt is stopped, the fan will automatically
turn off after a few minutes.
Note: To find an appropriate starting goal, walk on
the treadmill with the manual mode selected (see
page 12), and note the number of steps that you
walk during your workout. Then, round that num-
ber up to the nearest 500 steps. This can be a
starting goal. As your fitness level improves, you
can increase the goal by 500 steps every few
weeks. IMPORTANT: Always exercise at an in-
tensity level and for a length of time that is
comfortable for you.
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion, or the treadmill will be damaged. Next, re-
move the key from the console and put it in a se-
cure place. Note: If the displays remains lit after
the key is removed, the console is in the
“demo” mode. See page 15 and turn off the
demo mode.
Press the Start button or the Speed increase
button to start the program.
3
A moment after the button is pressed, the walking
belt will begin to move at 2 mph. Hold the
handrails and begin walking.
As you exercise, adjust the speed and incline of
the treadmill as desired by pressing the Speed
and Incline buttons.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
During the program, the MyTracks™ StepCounter
display will show the number of steps still to be
taken. When only ten steps remain, the
MyTracks™ StepCounter display will flash and a
tone will sound repeatedly until you reach the
goal. The walking belt will then slow to a stop.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the program temporarily, press the Stop
button. The time will begin to flash in the right dis-
play. To restart the program, press the Start button
or the Speed increase button. The walking belt will
begin to move at 2 mph. To end the program,
press the Stop button, remove the key, and then
reinsert the key.
HOW TO USE A PRESET PROGRAM
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
11.
Follow your progress with the displays.
See step 5 on page 12.
Select a preset program.
4
5
6
7
2
To select a preset pro-
gram, press the
Programs button re-
peatedly. When a pre-
set program is selected,
the left display will flash
the maximum speed setting of the program for a
few seconds, and the right display will show how
long the program will last. Note: If the walking belt
is moving when the Programs button is pressed,
the walking belt will slow to a stop.
Measure your heart rate if desired.
See step 6 on page 13.
Turn on the workout fan if desired.
See step 7 on page 13.
When the program is completed, remove the
key from the console.
Press the Start button or the Speed increase
button to start the program.
3
See step 8 on page 13.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several time periods
of different lengths. One speed setting and one in-
cline setting are programmed for each period.
Note: The same speed setting and/or incline setting
may be programmed for two or more consecutive
periods.
When only three seconds remain in the first period
of the program, the left display will flash and a se-
ries of tones will sound. The treadmill will then au-
tomatically adjust to the speed and incline settings
for the second period.
Note: If the speed setting and/or incline setting for
the current period is too high or too low, you can
manually override the setting by pressing the
speed and incline buttons. However, when the
next period of the program begins, the tread-
mill will automatically adjust to the speed and
incline settings for the next period.
The program will continue until no time remains in
the right display. The walking belt will then slow to
a stop.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the program temporarily, press the Stop
button. The time will begin to flash in the right dis-
play. To restart the program, press the Start button
or the Speed increase button. The walking belt will
begin to move at 1 mph. When the next period of
the program begins, the treadmill will automatically
adjust to the speed and incline settings for the
next period. To end the program, press the Stop
button, remove the key, and then reinsert the key.
THE INFORMATION MODE
The console features an information mode that keeps
track of treadmill usage information and allows you to
select a unit of measurement for the console.
To select the information mode, insert the key into the
console while holding down the Stop button, and then
release the Stop button. When the information mode is
selected, the following information will be shown:
Follow your progress with the displays.
See step 5 on page 12.
4
5
6
7
An “E” (for English) or an “M”
(for metric) will appear in the
left display. Press the Speed
increase button to change
the unit of measurement, if
desired. IMPORTANT: If a
“d” appears in the left display, the console is in the
“demo” mode. This mode is intended to be used only
when a treadmill is displayed in a store. When the con-
sole is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the displays will remain lit, although the buttons will
not operate. If a “d” appears when the information
mode is selected, press the Speed decrease button
so the “d” disappears.
Measure your heart rate if desired.
See step 6 on page 13.
Turn on the workout fan if desired.
See step 7 on page 13.
When the program is completed, remove the
key from the console.
See step 8 on page 13.
The MyTracks™
StepCounter display will
show the total number of
steps taken by all users of
the treadmill. Note: If the total
number exceeds 99,999, a
“K” will appear in the display and the display will show
the number of thousands of steps taken.
The right display will show
the total number of hours
that the treadmill has been
used and the total number of
miles (or kilometers) that the
walking belt has moved.
To exit the information mode, remove the key from the
console.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be per-
manently damaged. Next, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) to raise,
lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown by
the arrow at the right. Raise the treadmill about halfway to the
vertical position. To decrease the possibility of injury,
bend your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather than
your back.
2. Move your right hand to the position shown and hold the
2
treadmill firmly. Using your left thumb, press the storage latch
to the left. Raise the treadmill until the storage latch closes
over the catch. Make sure that the storage latch is fully
engaged over the catch.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sun-
light. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Engaged
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the storage latch
is fully engaged over the catch.
1. Hold the upper ends of the handrails, and place one foot
against one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while mov-
ing the treadmill. Do not move the treadmill over an un-
even surface.
Front Wheels
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the upper end of the treadmill with your right hand. Press the storage latch to the
left. Pivot the treadmill down until the frame and the foot rail are past the storage latch.
2. See drawing 1. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not drop the
treadmill. To decrease the possibility of injury, bend your legs and keep your back straight.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call the toll-free telephone number on the
front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 10. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
Tripped
Reset
and then press the switch back in.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still does not run, see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
49
POWER CORD. Remove the Screws (49) from the
Hood (1), and carefully pivot the Hood off.
1
Locate the Reed Switch (10) and the Magnet (18) on
the left side of the Pulley (17). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 1/8”. If necessary, loosen the
Screw (49), move the Reed Switch slightly, and then
retighten the Screw. Reattach the Hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
1/8”
49
17
18
10
Top
View
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 10.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
2”–3”
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller bolts counterclockwise, 1/4 of a turn. When
the walking belt is properly tightened, you should be
able to lift each side of the walking belt 2 to 3 inches
off the walking platform. Be careful to keep the walk-
ing belt centered. Plug in the power cord, insert the
key, and run the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
a
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
left bolt counterclockwise 1/2 of a turn. Be careful not
to overtighten the walking belt. Plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
b
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the walk-
ing belt 2 to 3 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
PROBLEM: The treadmill does not count your steps accurately
SOLUTION: a. For the treadmill to count your steps accurately, correct walking form is important. As you walk,
try to maintain a steady pace, a uniform stride length, and a consistent position on the treadmill.
Lighter users may also find it helpful to reduce the incline of the treadmill or to increase the speed
of the walking belt. IMPORTANT: Always walk at a speed that is comfortable for you. Note:
The treadmill, like pedometers and other step counting devices, may not count your first few
steps each time you begin walking and may occasionally not count a step while you are walking.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, reinsert the key. The treadmill will rise to the maximum in-
cline level and then return to the minimum level. This will recalibrate the incline system.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
WORKOUT GUIDELINES
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
To measure your heart rate during exercise, use the
pulse sensor.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. IMTL39105.0
R0605A
To locate the parts listed below, see the EXPLODED DRAWING.
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
1
19
1
1
5
2
1
1
1
1
1
2
7
Hood
3/4” Screw
Motor Belt
Motor Tension Bolt
3/8” Washer
Motor Star Washer
Flywheel
37
38
39
40
41
42
43
44
45
46
47
48
49
2
2
4
4
1
1
1
1
2
1
1
10
14
3” Bolt
Washer
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
#
1
1
2
4
1
1
1
1
2
4
1
1
1
1
1
1
1
1
2
1
1
1
1
6
2
1
1
1
1
1
1
Left Foot Rail Endcap
Silver Ground Screw
Handrail Endcap
Wire Tie
Reset/Off Switch
Power Cord
Power Cord Grommet
Belly Pan
Belt Guide
1” Tek Screw
Fan Cover Screw
Small Star Washer
Upright Wire
Console
Latch Spacer
Isolator
Photo Switch
Console Base
1/2” Screw
Drive Motor
Right Upright
Reed Switch
Latch Warning Decal
Frame Spacer
Frame Pivot
Nut/Motor Nut
Frame Pivot Bolt
Walking Platform
Screw
Foot Rail
Front Roller/Pulley
Magnet
Motor Pivot Bolt
Motor Bracket Bolt
Right Foot Rail
Endcap
Belly Pan Clip
Optic Disk
Isolator Screw
Ground Screw
Platform Nut
Fan Grill, Back
Motor Tension Nut
Storage Latch
Latch Catch
Rear Endcap Pad
Wheel Nut
Static Decal
Belt Guide Screw
Fan
Rear Roller
Hood Screw/
Deck Rail Screw
Key/Clip
Frame
Walking Platform
Warning Decal
Cable Tie Clamp
Inlet Plate
14
15
2
4
50
51
52
53
1
1
1
1
Incline Motor
Incline Bracket
Incline Motor
Bolt (lower)
Incline Pivot Bolt
Motor Mount Bracket
Motor Controller Wire
Base Pad
3/4” Tek Screw
Controller
Lift Frame
Left Upright
Warning Decal
Isolator Cushion
2” Bolt
Base Endcap
Wheel
16
17
18
19
20
21
2
1
1
1
2
1
Sensor Clip
Roller Adjustment Bolt
Right Rear Endcap
Allen Wrench
Left Rear Endcap
Walking Belt
5/16” Star Washer
4” Bolt
Filter Wire
Inlet Plate Screw
8” Black Wire, R/R
6” Black Wire, R/R
4” Black Wire, F/F
4” Black Wire, M/F
4” Blue Wire, F/F
4” Red Wire, M/F
8” Green Wire, F/R
User’s Manual
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
3
1
1
4
11
1
1
1
2
2
2
2
2
4
4
1
1
1
1
1
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
3
1
4
5
2
1
2
1
1
2
2
2
1
1
1
#
#
#
#
#
#
#
U-nut
8” Cable Tie
Base
1
1
1
Grommet
Left Grip Plate
Small Nut
Right Grip Plate
Left Handrail
Right Handrail
Small Nut
#These parts are not illustrated.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
the following information:
• the MODEL NUMBER of the product (IMTL39105.0)
• the NAME of the product (IMAGE 15.0 R treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST and the EXPLODED DRAWING
in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The motor is warranted for three (3) years after the
date of purchase. Parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For in-
home service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, im-
proper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 226024 R0605A
Printed in USA © 2005 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|