Image Treadmill IMTL119050 User Manual

Model No. IMTL11905.0  
Serial No.  
USER'S MANUAL  
Write the serial number in the space  
above for future reference.  
Serial Number  
Decal  
QUESTIONS?  
As a manufacturer, we are com-  
mitted to providing complete  
customer satisfaction. If you  
have questions, or if parts are  
damaged or missing, PLEASE  
CONTACT OUR CUSTOMER  
SERVICE DEPARTMENT DI-  
RECTLY.  
CALL TOLL-FREE:  
1-800-753-4645  
Mon.–Fri., 6 a.m.–6 p.m. MST  
ON THE WEB:  
CAUTION  
Visit our website at  
Read all precautions and instruc-  
tions in this manual before using  
this equipment. Save this man-  
ual for future reference.  
new products, prizes,  
fitness tips, and much more!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT PRECAUTIONS  
WARNING:  
To reduce the risk of burns, fire, electric shock, or injury to persons, read the  
following important precautions and information before operating the treadmill.  
1. It is the responsibility of the owner to ensure  
that all users of this treadmill are adequately  
informed of all warnings and precautions.  
11. Failure to use a properly functioning surge  
suppressor could result in damage to the con-  
trol system of the treadmill. If the control sys-  
tem is damaged, the walking belt may change  
speed, accelerate, or stop unexpectedly,  
which may result in a fall and serious injury.  
2. Use the treadmill only as described in this  
manual.  
12. Keep the power cord and the surge suppres-  
sor away from heated surfaces.  
3. Place the treadmill on a level surface, with at  
least eight feet of clearance behind it and two  
feet on each side. Do not place the treadmill  
on any surface that blocks air openings. To  
protect the floor or carpet from damage, place  
a mat under the treadmill.  
13. Never move the walking belt while the power  
is turned off. Do not operate the treadmill if  
the power cord or plug is damaged, or if the  
treadmill is not working properly. (See  
BEFORE YOU BEGIN on page 5 if the tread-  
mill is not working properly.)  
4. Keep the treadmill indoors, away from mois-  
ture and dust. Do not put the treadmill in a  
garage or covered patio, or near water.  
14. Read, understand, and test the emergency  
stop procedure before using the treadmill (see  
TREADMILL OPERATION).  
5. Do not operate the treadmill where aerosol  
products are used or oxygen is administered.  
15. Never start the treadmill while you are stand-  
ing on the walking belt. Always hold the  
handrails while using the treadmill.  
6. Keep children under the age of 12 and pets  
away from the treadmill at all times.  
16. The treadmill is capable of high speeds.  
Adjust the speed in small increments to avoid  
sudden jumps in speed.  
7. The treadmill should not be used by persons  
weighing more than 400 pounds. Never allow  
more than one person on the treadmill at a time.  
17. The pulse sensors are not medical devices.  
Various factors, including the user's move-  
ment, may affect the accuracy of heart rate  
readings. The pulse sensors are intended  
only as exercise aids in determining heart  
rate trends in general.  
8. Wear appropriate exercise clothes when  
using the treadmill. Do not wear loose clothes  
that could become caught in the treadmill.  
Athletic support clothes are recommended  
for both men and women. Always wear ath-  
letic shoes. Never use the treadmill with bare  
feet, wearing only stockings, or in sandals.  
18. Never leave the treadmill unattended while it  
is running. Always remove the key, unplug  
the power cord and move the reset/off circuit  
breaker to the off position when the treadmill  
is not in use. (See the drawing on page 5 for  
the location of the circuit breaker.)  
9. When connecting the power cord (see page 9),  
plug the power cord into a surge suppressor  
(not included) and plug the surge suppressor  
into a grounded circuit capable of carrying 15  
or more amps. No other appliance should be on  
the same circuit. Do not use an extension cord.  
19. Do not attempt to raise, lower, or move the  
treadmill until it is properly assembled. (See  
ASSEMBLY on page 6, and HOW TO FOLD  
AND MOVE THE TREADMILL on page 25.)  
You must be able to safely lift 45 pounds (20  
kg) to raise, lower, or move the treadmill.  
10. Use only a single-outlet surge suppressor that  
meets all of the specifications described on  
page 11. To purchase a surge suppressor, see  
your local IMAGE dealer or call the toll-free  
telephone number on the front cover of this  
manual and order part number 146148, or see  
your local electronics store.  
20. When folding or moving the treadmill, make  
sure that the storage latch is fully closed.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
21. When using iFIT.com CDs and videos, an  
electronic “chirping” sound will alert you  
when the speed and/or incline of the treadmill  
is about to change. Always listen for the  
“chirp” and be prepared for speed and/or in-  
cline changes. In some instances, the speed  
and/or incline may change before the per-  
sonal trainer describes the change.  
24. Inspect and properly tighten all parts of the  
treadmill every three months.  
25. Never drop or insert any object into any open-  
ing.  
26.  
DANGER:  
Always unplug the power  
cord immediately after use, before cleaning  
the treadmill, and before performing the main-  
tenance and adjustment procedures de-  
scribed in this manual. Never remove the  
motor hood unless instructed to do so by an  
authorized service representative. Servicing  
other than the procedures in this manual  
should be performed by an authorized service  
representative only.  
22. When using iFIT.com CDs and videos, you can  
manually override the speed and incline set-  
tings at any time by pressing the speed and in-  
cline buttons. However, when the next “chirp”  
is heard, the speed and/or incline will change  
to the next settings of the CD or video program.  
23. Always remove iFIT.com CDs and videos from  
your CD player or VCR when you are not  
using them.  
27. The treadmill is intended for in-home use  
only. Do not use the treadmill in any  
commercial, rental, or institutional setting.  
WARNING:  
Before beginning this or any exercise program, consult your physician. This  
is especially important for persons over the age of 35 or persons with pre-existing health problems.  
Read all instructions before using. ICON assumes no responsibility for personal injury or property  
damage sustained by or through the use of this product.  
SAVE THESE INSTRUCTIONS  
The decals shown here have been placed on your treadmill. If a decal is missing,  
or if it is not legible, please call the toll-free telephone number on the front cover  
of this manual and order a free replacement decal. Apply the decal in the location  
shown. Note: The decals are not shown at actual size.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE YOU BEGIN  
Congratulations for purchasing the IMAGE® AD-  
VANCED 2400 treadmill. The ADVANCED 2400 tread-  
mill offers an impressive array of features to help you  
achieve your fitness goals in the convenience of your  
home. From the advanced console to the cushioned  
walking platform, the ADVANCED 2400 treadmill is de-  
signed to make each workout more effective and en-  
joyable. And when you’re not exercising, the treadmill  
can be folded away, taking less than half the floor  
space of conventional treadmills.  
reading this manual, please see the front cover of this  
manual. To help us assist you, note the product model  
number and serial number before calling. The model  
number of the treadmill is IMTL11905.0. The serial  
number can be found on a decal attached to the tread-  
mill (see the front cover of this manual for the location).  
To avoid a registration fee for any service needed  
under warranty, you must register the treadmill at  
For your benefit, read this manual carefully before  
you use the treadmill. If you have questions after  
Before reading further, please review the drawing  
below and familiarize yourself with the labeled parts.  
Book Holder  
Tray  
Fan  
Console  
Key/Clip  
Handrail  
Handgrip Pulse Sensor  
Reset/Off  
Circuit Breaker  
Walking Belt  
Foot Rail  
Power Cord  
Adjustable Cushioned  
Walking Platform  
(See page 24)  
RIGHT SIDE  
BACK  
Rear Roller  
Adjustment Bolts  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480.  
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not  
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is  
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the  
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-  
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,  
non-abrasive cleaner.  
Assembly requires a phillips screwdriver  
and the included allen wrench  
.
1. With the help of a second person, carefully raise the  
Uprights (65) to a vertical position.  
1
Console  
Assembly  
Have the second person hold the console assembly near  
the Uprights (65) as shown. Look under the console as-  
sembly and locate the Console Wire Harness (71).  
Cut the plastic ties securing the Upright Wire Harness  
(85) to the right Upright (65). Connect the Upright Wire  
Harness to the Console Wire Harness (71). Make sure to  
connect the connectors properly (see the inset draw-  
ing). The connectors should slide together easily and  
snap into place. If the connectors do not slide together  
easily and snap into place, turn one connector and try  
again. IF THE CONNECTORS ARE NOT CONNECTED  
PROPERLY, THE CONSOLE MAY BE DAMAGED  
WHEN THE POWER IS TURNED ON.  
71  
85  
65  
71  
85  
2. Insert the excess Wire Harnesses (71, 85) into the right  
Upright (65).  
2
Console  
Assembly  
Set the console assembly on the Uprights (65). While a  
second person holds the console assembly, attach the  
console assembly with four Console Bolts (133) and four  
Console Washers (69) as shown. Firmly tighten the  
Console Bolts.  
71, 85  
69  
69  
133  
133  
65  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. With the help of a second person, raise the treadmill  
Frame (55). Hold the Latch Housing (68) and the Latch  
Housing Cover (5) against the sides of the Frame as  
shown. Loosely thread the two blunt-tipped 1/2” Screws  
(132) into the Latch Housing Cover and the Latch Housing  
as shown. Do not tighten the Screws yet.  
3
Hole  
Knob  
132  
Remove the knob from the pin. Make sure that the collar  
and the spring are on the pin. The collar should be on the  
side of the spring shown. Insert the pin into the Latch  
Housing (68), and tighten the knob back onto it.  
87  
49  
5
68  
Small  
Holes  
Align the pin with the hole in the Left Handgrip (87) by slid-  
ing the Latch Housing (68) up or down. Make sure that the  
pin can be inserted fully into the hole. Hold the Latch  
Housing in place as you tighten two 1/2” Tek Screws (49)  
into the Latch Housing and the Frame (55). Then, tighten  
the 1/2” Screws (132). Note: It may be necessary to pull  
on the knob to access and tighten the Screws.  
Collar  
55  
Spring  
132  
Pin  
49  
4. Remove the backing from the indicated tape on the con-  
sole assembly. Press the Book Holder (50) firmly onto the  
tape. Note: The Book Holder may be preassembled.  
4
50  
Console  
Assembly  
Tape  
5. Make sure that all parts are properly tightened before you use the treadmill. Place a mat beneath the  
treadmill to protect the floor or carpet. Keep the included allen wrench in a secure place. The allen wrench  
is used to adjust the walking belt (see pages 26 and 27).  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO USE THE CHEST PULSE SENSOR  
HOW TO PUT ON THE CHEST PULSE SENSOR  
dried. If the chest pulse sensor is not dried after  
each use, it may remain activated longer than nec-  
essary, draining the battery prematurely.  
The chest pulse sensor consists of two components:  
the chest strap and the sensor unit (see the drawing  
below). Insert the tab on one end of the chest strap into  
one end of the sensor unit, as shown in the inset draw-  
ing. Press the end of the sensor unit under the buckle  
on the chest strap. The tab should be flush with the  
front of the sensor unit.  
• Store the chest pulse sensor in a warm, dry place.  
Do not store the chest pulse sensor in a plastic bag  
or other container that may trap moisture.  
• Do not expose the chest pulse sensor to direct  
sunlight for extended periods of time; do not expose  
it to temperatures above 122° Fahrenheit (50°  
Celsius) or below 14° Fahrenheit (-10° Celsius).  
• Do not excessively bend or stretch the sensor unit  
when using or storing the chest pulse sensor.  
Chest Strap  
Tabs  
• Clean the sensor unit using a damp cloth—never  
use alcohol, abrasives, or chemicals. The chest  
strap may be hand washed and air dried.  
Tab  
CHEST PULSE SENSOR TROUBLESHOOTING  
Sensor  
Unit  
Buckle  
Sensor Unit  
The instructions on the following pages explain  
how the chest pulse sensor is used with the con-  
sole. If the chest pulse sensor does not function  
properly, try the steps below.  
Next, wrap the  
chest pulse sen-  
sor around your  
chest and attach  
the other end of  
the chest strap to  
the sensor unit.  
Adjust the length  
of the chest strap,  
if necessary. The  
chest pulse sen-  
• Make sure that you are wearing the chest pulse sen-  
sor as described at the left. Note: If the chest pulse  
sensor does not function when positioned as de-  
scribed, move it slightly lower or higher on your chest.  
• Use saline solution such as saliva or contact lens  
solution to wet the two electrode areas on the  
sensor unit. If heart rate readings do not appear until  
you begin perspiring, re-wet the electrode areas.  
sor should be under your clothes, tight against your  
skin, and as high under the pectoral muscles or  
breasts as is comfortable. Make sure that the logo on  
the sensor unit is facing forward and is right-side-up.  
• As you walk or run on the treadmill, position your-  
self near the center of the walking belt. For the  
console to display heart rate readings, the user  
must be within arm’s length of the console.  
Pull the sensor unit away from your body a few inches  
and locate the two electrode areas on the inner side  
(the electrode areas are covered by shallow ridges).  
Using saline solution such as saliva or contact lens so-  
lution, wet both electrode areas. Return the sensor unit  
to a position against your chest.  
• The chest pulse sensor is designed to work with  
people who have normal heart rhythms. Heart rate  
reading problems may be caused by medical  
conditions such as premature ventricular contrac-  
tions (pvcs), tachycardia bursts, and arrhythmia.  
CHEST PULSE SENSOR CARE AND MAINTENANCE  
• The operation of the chest pulse sensor can be  
affected by magnetic interference caused by high  
power lines or other sources. If it is suspected that  
this is a problem, try relocating the treadmill.  
• Thoroughly dry the chest pulse sensor after each  
use. The chest pulse sensor is activated when the  
electrode areas are wetted and the heart rate  
monitor is put on; the chest pulse sensor shuts off  
when it is removed and the electrode areas are  
• The CR2032 battery may need to be replaced (see  
page 27).  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
TREADMILL OPERATION  
THE PRE-LUBRICATED WALKING BELT  
tric shock. This product is equipped with a cord having  
an equipment-grounding conductor and a grounding  
plug. Plug the power cord into a surge suppressor,  
and plug the surge suppressor into an appropriate  
outlet that is properly installed and grounded in  
accordance with all local codes and ordinances.  
Important: The treadmill is not compatible with  
GFCI-equipped outlets.  
Your treadmill features a walking belt coated with high-  
performance lubricant. IMPORTANT: Never apply sil-  
icone spray or other substances to the walking  
belt or the walking platform. Such substances will  
deteriorate the walking belt and cause excessive  
wear.  
HOW TO PLUG IN THE POWER CORD  
This product is for use on a nominal 120-volt circuit,  
and has a grounding plug that looks like the plug illus-  
trated in drawing 1 below. A temporary adapter that  
looks like the adapter illustrated in drawing 2 may be  
used to connect the surge suppressor to a 2-pole  
receptacle as shown in drawing 2 if a properly  
grounded outlet is not available.  
DANGER:  
Improper connection  
of the equipment-grounding conductor can  
result in an increased risk of electric shock.  
Check with a qualified electrician or service-  
man if you are in doubt as to whether the  
product is properly grounded. Do not modify  
the plug provided with the product—if it will  
not fit the outlet, have a proper outlet  
1
Grounded Outlet Box  
Surge Suppressor  
Grounding Pin  
installed by a qualified electrician.  
Your treadmill, like any other type of sophisticated  
electronic equipment, can be seriously damaged by  
sudden voltage changes in your home’s power.  
Voltage surges, spikes, and noise interference can  
result from weather conditions or from other appliances  
being turned on or off. To decrease the possibility of  
your treadmill being damaged, always use a surge  
suppressor with your treadmill (see drawing 1 at  
the right). To purchase a surge suppressor, see  
your local IMAGE dealer or call the toll-free tele-  
phone number on the front cover of this manual  
and order part number 146148, or see your local  
electronics store.  
Grounding Pin  
Grounded Outlet  
Grounding Plug  
2
Grounded Outlet Box  
Adapter  
Surge Suppressor  
Use only a single-outlet surge suppressor that is  
UL 1449 listed as a transient voltage surge sup-  
pressor (TVSS). The surge suppressor must have a  
UL suppressed voltage rating of 400 volts or less  
and a minimum surge dissipation of 450 joules.  
The surge suppressor must be electrically rated for  
120 volts AC and 15 amps. There must be a moni-  
toring light on the surge suppressor to indicate  
whether it is functioning properly. Failure to use a  
properly functioning surge suppressor could result  
in damage to the control system of the treadmill. If  
the control system is damaged, the walking belt  
may change speed, accelerate, or stop unexpect-  
edly, which may result in a fall and serious injury.  
Lug  
Metal Screw  
The temporary adapter should be used only until a  
properly grounded outlet (drawing 1) can be installed  
by a qualified electrician.  
The green-colored rigid ear, lug, or the like extending  
from the adapter must be connected to a permanent  
ground such as a properly grounded outlet box cover.  
Whenever the adapter is used it must be held in place  
by a metal screw. Some 2-pole receptacle outlet box  
covers are not grounded. Contact a qualified elec-  
trician to determine if the outlet box cover is  
grounded before using an adapter.  
This product must be grounded. If it should malfunc-  
tion or break down, grounding provides a path of least  
resistance for electric current to reduce the risk of elec-  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note: If there are thin sheets of clear  
plastic on the console, remove them.  
Key  
Clip  
FEATURES OF THE CONSOLE  
cable, you can connect the treadmill to your home  
stereo, portable stereo, computer, or VCR and play  
special iFIT.com CD and video programs (iFIT.com  
CDs and videocassettes are available separately).  
iFIT.com CD and video programs automatically control  
the speed and incline of the treadmill as a personal  
trainer coaches you through every step of your work-  
out. High-energy music provides added motivation. To  
purchase iFIT.com CDs or videocassettes, call the  
toll-free telephone number on the front cover of  
The treadmill console offers an impressive array of  
features designed to help you get the most from your  
workouts.  
When the manual mode of the console is selected, the  
speed and incline of the treadmill can be changed with  
a touch of a button. As you exercise, the console will  
display instant exercise feedback. You can even mea-  
sure your heart rate using the handgrip pulse sensor or this manual.  
the chest pulse sensor.  
With the treadmill connected to your computer, you  
The console also offers six personal trainer programs.  
Each program automatically controls the speed and in-  
cline of the treadmill as it guides you through an effec-  
tive workout. Two heart rate programs are also offered.  
Each program adjusts the speed and incline of the  
treadmill to keep your heart rate near a target heart rate  
while you exercise. You can even create custom pro-  
grams and save them in memory for future workouts.  
cess programs directly from the internet. Additional op-  
tions are soon to be available. See www.iFIT.com for  
more information.  
To use the manual mode of the console, follow the  
steps beginning on page 11. To use a personal trainer  
program, see page 13 To use a heart rate program,  
see page 15. To create and use a custom program,  
see pages 17 and 18. To use an iFIT.com CD or video  
The console also features new iFIT.com interactive  
technology. Having iFIT.com technology is like having a program, see page 21. To use an iFIT.com program  
personal trainer in your home. Using the included audio directly from our Web site, see page 23.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO TURN ON THE POWER  
If the Start button or the  
Speed increase button is  
Note: To prevent damage to the walking platform,  
always wear clean shoes when using the treadmill.  
pressed, the walking belt  
will begin to move at 1  
mph. As you exercise,  
Plug in the power cord (see  
page 9). Next, locate the  
change the speed of the  
walking belt as desired by pressing the Speed in-  
crease and decrease buttons. Each time a button  
is pressed, the speed setting will change by 0.1  
mph; if a button is held down, the speed setting  
will change in increments of 0.5 mph.  
Reset  
Position  
reset/off circuit breaker on  
the treadmill frame near the  
power cord. Make sure that  
the circuit breaker is in the  
reset position.  
If one of the Quick Start buttons is pressed, the  
walking belt will gradually increase in speed until it  
reaches the selected speed setting. Note: The  
console can display speed and distance in ei-  
ther miles or kilometres. For simplicity, all in-  
structions in this section refer to miles.  
Stand on the foot rails of the treadmill. Find the clip at-  
tached to the key (see the drawing on page 10) and  
slide the clip onto the waistband of your clothes. Next,  
route the cord attached to the clip under the handgrip  
pulse sensor, and insert the key into the console.  
After a moment, the displays and various indicators will  
light. Important: In an emergency situation, the key  
can be pulled from the console, causing the walk-  
ing belt to slow to a stop. Test the clip by carefully  
taking a few steps backward; if the key is not  
pulled from the console, adjust the position of the  
clip.  
To stop the walking belt, press the Stop button.  
The time will begin to flash in the Pace/Time dis-  
play. To restart the walking belt, press the Start  
button, the Speed increase button, or one of the  
twelve Quick Start buttons.  
Note: The first time the treadmill is used, observe  
the alignment of the walking belt, and align the  
walking belt if necessary (see page 27).  
HOW TO USE THE MANUAL MODE  
Change the incline of the treadmill as desired.  
Insert the key into the console.  
4
5
1
To change the incline of  
the treadmill, press the  
Incline increase and de-  
crease buttons. Each  
time a button is pressed,  
the incline will change by  
0.5%.  
See HOW TO TURN ON THE POWER above.  
Select the manual mode.  
2
When the key is in-  
serted, the manual  
mode will be selected  
and the indicator on the  
Manual Control button  
will light. If you have se-  
Follow your progress with the matrix and the  
displays.  
lected a program, reselect the manual mode by  
pressing the Manual Control button.  
The matrix—When the  
manual mode or the  
iFIT.com mode is se-  
lected, the matrix will  
Start the walking belt.  
3
display a 1/4-mile track.  
As you exercise, the in-  
dicators around the track  
will light in succession until the entire track is lit.  
The track will then darken and the indicators will  
again begin to light in succession.  
To start the walking belt, press the Start button,  
the Speed increase button, or one of the twelve  
Quick Start buttons.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Distance/Incline dis-  
play—This display  
shows the distance that  
you have walked or run  
Measure your heart rate if desired.  
6
Note: If you use  
the handgrip  
and the incline level of  
the treadmill. The display  
will change from one number to the other every  
few seconds. Note: Each time the incline changes,  
the display will show the incline setting for several  
seconds.  
pulse sensor and  
the chest pulse  
sensor at the  
same time, the  
console will not  
display your  
Contacts  
heart rate accu-  
Calories/Pulse  
display—This display  
shows the approximate  
number of calories you  
rately. Before using the handgrip pulse sensor, re-  
move the clear plastic film from the metal con-  
tacts. In addition, make sure that your hands are  
clean.  
have burned. The dis-  
play will also show your  
To use the handgrip pulse sensor, first make sure  
that your hands are clean. Next, stand on the  
foot rails and hold the handgrip pulse sensor,  
with your palms on the metal contacts. Avoid  
moving your hands. When your pulse is detected,  
two dashes (– –) will appear in the Calories/Pulse  
display, and then your heart rate will be shown.  
For the most accurate heart rate reading, con-  
tinue to hold the contacts for about 15 sec-  
onds.  
heart rate when you use the handgrip pulse sen-  
sor or the chest pulse sensor. The display will  
change from one number to the other every few  
seconds.  
Speed display—This  
display shows the  
speed of the walking  
belt.  
Turn on the fan if desired.  
7
8
Note: The console can  
display speed and dis-  
tance in either miles or  
kilometres. To find which  
unit of measurement is  
selected, hold down the  
Stop button while inserting the key into the con-  
sole. An “E” for English miles or an “M” for metric  
kilometres will appear in the Speed display. Press  
the Speed increase button to change the unit of  
measurement. When the desired unit of measure-  
ment is selected, remove the key.  
To turn on the fan, press the button below the fan.  
To turn on the fan at high speed, press the button  
a second time. To turn off the fan, press the but-  
ton a third time. Note: A few minutes after the  
walking belt is stopped, the fan will automatically  
turn off.  
When you are finished exercising, remove the  
key from the console.  
Step onto the foot rails, press the Stop button, and  
adjust the incline of the treadmill to the lowest  
setting. The incline must be at the lowest setting  
when the treadmill is folded to the storage posi-  
tion or the treadmill will be damaged. Next, re-  
move the key from the console and put it in a se-  
cure place. Note: If the displays and various indi-  
cators on the console remain lit after the key is  
removed, the console is in the “demo” mode.  
See page 24 and turn off the demo mode.  
Pace/Time display—  
When the manual mode  
or the iFIT.com mode is  
selected, this display will  
show your current pace,  
in minutes per mile, and  
the elapsed time. The display will change from  
one number to the other every few seconds.  
When a program is selected (except for the Self  
Select heart rate program), the display will show  
the elapsed time and the time remaining in the pro-  
gram.  
When you are finished using the treadmill,  
move the reset/off circuit breaker to the off po-  
sition and unplug the power cord.  
To reset the displays, press the Stop button, re-  
move the key, and then reinsert the key.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The speed setting for the  
first segment is shown in  
the flashing Current  
HOW TO USE PERSONAL TRAINER PROGRAMS  
Current Segment  
Segment column of the  
matrix. (The incline set-  
tings are not shown in  
the matrix.) The speed  
settings for the next  
Insert the key into the console.  
1
See HOW TO TURN ON THE POWER on page  
11.  
seven segments are  
shown in the seven columns to the right.  
Select one of the personal trainer programs.  
2
To select a personal  
When only three seconds remain in the first seg-  
ment of the program, both the Current Segment  
column and the column to the right will flash and a  
series of tones will sound. If the speed and/or in-  
cline of the treadmill is about to change, the Speed  
display and/or the Distance/Incline display will  
flash to alert you. When the first segment ends, all  
speed settings will move one column to the left.  
The speed setting for the second segment will then  
be shown in the flashing Current Segment column  
and the treadmill will automatically adjust to the  
speed and incline settings for the second segment.  
Note: If all of the indicators in the Current Segment  
column are lit after the speed settings have moved  
to the left, the speed settings may move downward  
so that only the highest indicators appear in the  
matrix. If some of the indicators in the Current  
Segment column are not lit when the speed set-  
tings move to the left again, the speed settings will  
move back up.  
trainer program, press  
one of the Walk, Jog, or  
Run buttons. The indi-  
cator on the button that  
you press will light.  
When a personal trainer program is selected, the  
Speed display will flash the maximum speed set-  
ting of the program for a few seconds, and the  
Distance/Incline display will flash the maximum in-  
cline setting. The Pace/Time display will show  
how long the program will last.  
The matrix will show  
the first seven speed  
settings of the program.  
Note: The diagrams on  
the Walk, Jog, and Run  
buttons show how the  
speed and incline of  
the treadmill will change during the personal  
trainer programs. For example, the diagram on  
the right Walk button shows that the speed and in-  
cline will gradually increase during the first half of  
the program and then gradually decrease during  
the last half.  
The program will continue in this way until the  
speed setting for the last segment is shown in the  
Current Segment column and the last segment  
ends. The walking belt will then slow to a stop.  
If the speed or incline setting is too high or too low  
at any time during the program, you can manually  
override the setting by pressing the Speed or  
Incline buttons. Every few times a Speed button is  
pressed, an additional indicator will light or darken  
in the Current Segment column. (If any of the  
columns to the right of the Current Segment col-  
umn have the same number of lit indicators as the  
Current Segment column, an additional indicator  
may light or darken in those columns as well.)  
Note: When the next segment of the program  
begins, the treadmill will automatically adjust  
to the speed and incline settings for the next  
segment.  
Press the Start button or the Speed increase  
button to start the program.  
3
A moment after the button is pressed, the tread-  
mill will automatically adjust to the first speed and  
incline settings of the program. Hold the handrails  
and begin walking.  
Each program is divided into several time seg-  
ments of different lengths. One speed setting and  
one incline setting are programmed for each seg-  
ment. Note: The same speed setting and/or in-  
cline setting may be programmed for two or more  
consecutive segments.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To stop the program at any time, press the Stop  
button. The time will begin to flash in the  
When you are finished exercising, remove the  
key from the console.  
7
Pace/Time display. To restart the program, press  
the Start button or the Speed increase button. The  
walking belt will begin to move at 1 mph. When the  
next segment of the program begins, the treadmill  
will automatically adjust to the speed and incline  
settings for the next segment.  
When the program has ended, make sure that  
the incline of the treadmill is at the lowest set-  
ting. Next, remove the key from the console and  
put it in a secure place. Note: If the displays and  
various indicators on the console remain lit  
after the key is removed, the console is in the  
“demo” mode. See page 24 and turn off the  
demo mode.  
Follow your progress with the displays.  
See step 5 on page 11.  
4
5
6
When you are finished using the treadmill,  
move the reset/off circuit breaker to the off po-  
sition and unplug the power cord.  
Measure your heart rate if desired.  
See step 6 on page 12.  
Turn on the fan if desired.  
See step 7 on page 12.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enter your age.  
HOW TO USE HEART RATE PROGRAMS  
4
5
When a heart rate pro-  
gram is selected, the  
word “AGE” and the cur-  
rent age setting will flash  
in the Calories/Pulse  
display. If you have al-  
ready entered your age, simply press the Enter  
button. If you have not entered your age, press  
the increase and decrease buttons below the  
Enter button to enter your age. Then, press the  
Enter button.  
CAUTION:  
If you have heart prob-  
lems, or if you are over 60 years of age and  
have been inactive, do not use the heart rate  
programs. If you are taking medication regu-  
larly, consult your physician to find whether  
the medication will affect your exercise heart  
rate.  
Put on the chest pulse sensor.  
Enter a maximum speed.  
1
You must wear the chest pulse sensor (see  
page 8) to use a heart rate program.  
After you have entered  
your age, the letters  
“SPd” and the maximum  
speed setting of the pro-  
Insert the key into the console.  
2
3
gram will flash in the  
Speed display. If de-  
sired, press the increase and decrease buttons  
below the Enter button to adjust the maximum  
speed setting. When the desired setting is shown,  
press the Enter button.  
See HOW TO TURN ON THE POWER on  
page 11.  
Select a heart rate program.  
To select a heart rate  
program, press the  
85% Max or Self Select  
button. The indicator on  
the button that you  
press will light.  
If the 85% Max program is selected, go to step  
7. If the Self Select program is selected, go to  
step 6.  
Enter a target heart rate.  
6
7
During the 85% Max program, your heart rate will  
reach approximately 85% of your estimated maxi-  
mum heart rate; during the Self Select program,  
your heart rate will remain near a level that you  
select. Note: Your estimated maximum heart rate  
is determined by subtracting your age from 220.  
For example, if you are 30 years old, your esti-  
mated maximum heart rate is 190 beats per  
minute (220 – 30 = 190).  
The letters “PLS” and  
the target heart rate set-  
ting for the program will  
flash in the Calories/  
Pulse display. If desired,  
press the increase and  
decrease buttons below the Enter button to adjust  
the target heart rate setting. When the desired  
setting is shown, press the Enter button.  
During heart rate pro-  
grams, the matrix will  
show a moving graphic  
that represents your  
heart rate. Each time a  
heartbeat is detected, a  
peak will appear.  
Press the Start button or the Speed increase  
button to start the program.  
A moment after the button is pressed, the tread-  
mill will automatically adjust to the first speed and  
incline settings of the program. Hold the handrails  
and begin walking.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Each heart rate program is divided into several time  
segments of different lengths. One target heart rate  
is programmed for each segment. Note: If the Self  
Select program is selected, the same target heart  
rate is programmed for all segments.  
the current target heart rate, the speed and/or in-  
cline of the treadmill may automatically change to  
bring your heart rate closer to the target heart rate.  
If your pulse is not detected during the program,  
the letters “PLS” will flash in the Calories/Pulse  
display and the speed and incline of the treadmill  
may automatically decrease until your pulse is de-  
tected. If this occurs, see the instructions on page  
8.  
During each segment, the console will regularly  
compare your heart rate to the current target heart  
rate. If your heart rate is too far below or above  
the target heart rate, a tone will sound and the  
speed of the treadmill will automatically increase  
or decrease to bring your heart rate closer to the  
target heart rate. If the speed reaches the maxi-  
mum speed setting of the program (see step 5 on  
page 14) and your heart rate is still too far below  
the current target heart rate, the incline of the  
treadmill will also increase to bring your heart rate  
closer to the target heart rate.  
To stop the program at any time, press the Stop  
button. Heart rate programs cannot be stopped  
temporarily and then restarted. To use a heart rate  
program again, reselect the program and start it at  
the beginning.  
Follow your progress with the displays.  
See step 5 on page 11.  
8
9
During the last three seconds of each segment, a  
series of tones will sound and the Speed display  
and the Distance/Incline display will flash.  
Turn on the fan if desired.  
See step 7 on page 12.  
The program will continue until the last segment  
ends. The walking belt will then slow to a stop.  
When you are finished exercising, remove the  
key from the console.  
If the speed or incline setting is too high or too low  
at any time during the program, you can adjust the  
setting with the Speed or Incline buttons. However,  
each time the console compares your heart rate to  
10  
See step 7 on page 14.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
in the matrix.) To program a speed setting and an  
incline setting for the first segment, simply adjust  
the speed and incline of the treadmill as desired  
by pressing the Speed and Incline buttons. Every  
few times one of the Speed buttons is pressed, an  
additional indicator will light or darken in the  
Current Segment column.  
HOW TO CREATE CUSTOM PROGRAMS  
Insert the key into the console.  
1
See HOW TO TURN ON THE POWER on page  
11.  
During the last three seconds of the first segment,  
both the Current Segment column and the column  
to the right will flash, a series of tones will sound,  
and the Speed display and the Distance/Incline  
display will flash. When the first segment ends, the  
current speed setting and the current incline set-  
ting will be saved in memory, and all speed set-  
tings in the matrix will move one column to the left.  
The speed setting for the second segment will  
then be shown in the flashing Current Segment  
column. Program a speed setting and an incline  
setting for the second segment as described  
above.  
Select one of the custom programs.  
2
To select a custom pro-  
gram, press the Custom  
Program 1 button or the  
Custom Program 2 but-  
ton. The indicator on the  
button that you press will  
light.  
Press the Start button or the Speed increase  
button and program the desired speed and in-  
cline settings.  
3
Continue programming speed and incline settings  
for as many segments as desired; custom pro-  
grams can have up to forty segments. When you  
are finished with your workout, press the Stop but-  
ton twice. The speed and incline settings that you  
have programmed and the number of segments  
that you have programmed will then be saved in  
memory.  
A moment after the button is pressed, the walking  
belt will begin to move. Hold the handrails and  
begin walking.  
See the matrix. Each  
custom program is di-  
vided into one-minute  
segments. One speed  
setting and one incline  
setting can be pro-  
Current Segment  
When the program is finished, remove the key.  
4
grammed for each seg-  
ment. The speed setting  
for the first segment will  
See step 7 on page 14.  
be shown in the flashing Current Segment column  
of the matrix. (The incline settings are not shown  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
column and the column to the right will flash, a se-  
ries of tones will sound, the Speed display and the  
Distance/Incline display will flash, and all speed  
settings will move one column to the left. The  
speed setting for the second segment will then be  
shown in the flashing Current Segment column  
and the treadmill will automatically adjust to the  
second speed and incline settings that you pro-  
grammed previously.  
HOW TO USE CUSTOM PROGRAMS  
Insert the key into the console.  
1
See HOW TO TURN ON THE POWER on  
page 11.  
Select one of the custom programs.  
2
The program will continue until the speed setting  
for the last segment is shown in the Current  
Segment column and the last segment ends. The  
walking belt will then slow to a stop.  
To select a custom pro-  
gram, press the Custom  
Program 1 button or the  
Custom Program 2 but-  
ton. The indicator on  
the button that you  
If desired, you can change the program while  
using it. To change the speed or incline setting  
for the current segment, simply press the Speed  
or Incline buttons. When the current segment ends,  
the new setting will be saved in memory. To in-  
crease the length of the program, first wait until  
the program ends. Then, press the Start button and  
program speed and incline settings for as many ad-  
ditional segments as desired. When you have  
added as many segments as desired, press the  
Stop button twice. To decrease the length of the  
program, press the Stop button twice at any time  
before the program ends.  
press will light. When a custom program is se-  
lected, the Speed display will flash the maximum  
speed setting of the program for a few seconds,  
and the Distance/Incline display will flash the max-  
imum incline setting. The Pace/Time display will  
show how long the program will last.  
The matrix will show  
the first seven speed  
settings of the program.  
To stop the program at any time, press the Stop  
button. The time will begin to flash in the  
Press the Start button or the Speed increase  
button to start the program.  
3
Pace/Time display. To restart the program, press  
the Start button or the Speed increase button. The  
walking belt will begin to move at 1 mph. When the  
next segment of the program begins, the treadmill  
will automatically adjust to the speed and incline  
settings for the next segment.  
A moment after the button is pressed, the tread-  
mill will automatically adjust to the first speed and  
incline settings that you programmed previously.  
Hold the handrails and begin walking.  
Follow your progress with the displays.  
See step 5 on page 11.  
Each custom program is  
4
5
6
7
divided into several one-  
minute segments. One  
speed setting and one  
incline setting are pro-  
grammed for each seg-  
ment. The speed setting  
for the first segment is  
shown in the flashing  
Current Segment column of the matrix. (The in-  
cline settings are not shown in the matrix.) The  
speed settings for the next seven segments are  
shown in the columns to the right.  
Current Segment  
Measure your heart rate if desired.  
See step 6 on page 12.  
Turn on the fan if desired.  
See step 7 on page 12.  
When you are finished exercising, remove the  
key from the console.  
When only three seconds remain in the first seg-  
ment of the program, both the Current Segment  
See step 7 on page 14.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO CONNECT YOUR PORTABLE STEREO  
HOW TO CONNECT THE TREADMILL TO  
YOUR CD PLAYER, VCR, OR COMPUTER  
Note: If your stereo has an RCA-type AUDIO OUT  
jack, see instruction A below. If your stereo has a  
3.5mm LINE OUT jack, see instruction B. If your  
stereo has only a PHONES jack, see instruction C.  
To use iFIT.com CDs, the treadmill must be con-  
nected to your portable CD player, portable stereo,  
home stereo, or computer with CD player. See pages  
19 and 20 for connecting instructions. To use iFIT.com  
videocassettes, the treadmill must be connected to  
your VCR. See page 21 for connecting instructions. To  
use iFIT.com programs directly from our Web site,  
the treadmill must be connected to your home com-  
puter. See page 20 for connecting instructions.  
A. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into the included adapter. Plug  
the adapter into an AUDIO OUT jack on your stereo.  
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER  
AUDIO OUT  
RIGHT  
LEFT  
Note: If your CD player has separate LINE OUT and  
PHONES jacks, see instruction A below. If your CD  
player has only one jack, see instruction B.  
Audio  
Cable  
Adapter  
A. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into the LINE OUT jack on  
your CD player. Plug your headphones into the  
PHONES jack.  
B. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into the LINE OUT jack on  
your stereo.  
A
PHONES LINE OUT  
LINE OUT  
PHONES  
B
Head-  
phones  
Audio  
Cable  
LINE OUT  
Audio  
Cable  
B. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into a 3.5mm Y-adapter  
(available at electronics stores). Plug the Y-adapter  
into the PHONES jack on your CD player. Plug your  
headphones into the other side of the Y-adapter.  
C. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into a 3.5mm Y-adapter  
(available at electronics stores). Plug the Y-adapter  
into the PHONES jack on your stereo. Plug your  
headphones into the other side of the Y-adapter.  
B
PHONES  
C
PHONES  
3.5mm  
Y-adapter  
Audio  
Cable  
PHONES  
3.5mm  
Y-adapter  
Audio  
Cable  
Headphones  
Headphones  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO CONNECT YOUR HOME STEREO  
HOW TO CONNECT YOUR COMPUTER  
Note: If your stereo has an unused LINE OUT jack,  
see instruction A below. If the LINE OUT jack is  
being used, see instruction B.  
Note: If your computer has a 3.5mm LINE OUT jack,  
see instruction A. If your computer has only a  
PHONES jack, see instruction B.  
A. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into the included adapter.  
Plug the adapter into the LINE OUT jack on your  
stereo.  
A. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into the LINE OUT jack on  
your computer.  
A
A
CD  
LINE OUT  
VCR  
Amp  
LINE OUT  
Audio  
Cable  
LINE OUT  
Audio  
Cable  
Adapter  
B. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into a 3.5mm Y-adapter  
(available at electronics stores). Plug the Y-adapter  
into the PHONES jack on your computer. Plug your  
headphones or speakers into the other side of the  
Y-adapter.  
B. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into the included adapter.  
Plug the adapter into an RCA Y-adapter (available  
at electronics stores). Next, remove the wire that is  
currently plugged into the LINE OUT jack on your  
stereo and plug the wire into the unused side of the  
Y-adapter. Plug the Y-adapter into the LINE OUT  
jack on your stereo.  
B
PHONES  
B
CD  
3.5mm  
Y-adapter  
Audio  
Cable  
VCR  
Amp  
LINE OUT  
Headphones/Speakers  
RCA Y-adapter  
Audio  
Adapter  
Cable  
Wire removed from  
LINE OUT jack  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO CONNECT YOUR VCR  
HOW TO USE IFIT.COM CD AND VIDEO  
PROGRAMS  
Note: If your VCR has an unused AUDIO OUT jack,  
see instruction A below. If the AUDIO OUT jack is  
being used, see instruction B. If you have a TV  
with a built-in VCR, see instruction B. If your VCR  
is connected to your home stereo, see HOW TO  
CONNECT YOUR HOME STEREO on page 20.  
To use iFIT.com CDs or videocassettes, the treadmill  
must be connected to your portable CD player, portable  
stereo, home stereo, computer with CD player, or  
VCR. See HOW TO CONNECT THE TREADMILL TO  
YOUR CD PLAYER, VCR, OR COMPUTER on page  
19. To purchase iFIT.com CDs or videocassettes,  
call the toll-free telephone number on the front  
cover of this manual.  
A. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into the included adapter.  
Plug the adapter into the AUDIO OUT jack on your  
VCR.  
Follow the steps below to use an iFIT.com CD or video  
program.  
A
ANT IN  
.
VIDEO AUDIO  
IN  
RF OUT  
CH  
3
4
OUT  
Insert the key into the console.  
1
AUDIO OUT  
RIGHT  
LEFT  
See HOW TO TURN ON THE POWER on page 11.  
Select the iFIT.com mode.  
Audio  
Cable  
2
Adapter  
To use an iFIT.com CD  
or video program, press  
the iFIT.com button. The  
indicator on the button  
will light.  
B. Plug one end of the audio cable into the jack on the  
front of the treadmill near the power cord. Plug the  
other end of the cable into the included adapter.  
Plug the adapter into an RCA Y-adapter (available  
at electronics stores). Next, remove the wire that is  
currently plugged into the AUDIO OUT jack on your  
VCR and plug the wire into the unused side of the  
Y-adapter. Plug the Y-adapter into the AUDIO OUT  
jack on your VCR.  
Insert the iFIT.com CD or videocassette.  
3
If you are using an iFIT.com CD, insert the CD into  
your CD player. If you are using an iFIT.com video-  
cassette, insert the videocassette into your VCR.  
Press the PLAY button on your CD player or  
VCR.  
4
A moment after the button is pressed, your per-  
sonal trainer will begin guiding you through your  
workout. Simply follow your personal trainer’s  
instructions. Note: If the time is flashing in the  
Pace/Time display, press the Start button or the  
Speed increase button on the console. The tread-  
mill will not respond to a CD or video program  
while the Pace/Time display is flashing.  
B
ANT IN  
.
VIDEO AUDIO  
IN  
RF OUT  
CH  
3
4
OUT  
RCA Y-adapter  
Adapter  
Audio  
Cable  
During the CD or video program, an electronic  
“chirping” sound will alert you when the speed  
and/or incline of the treadmill is about to change.  
CAUTION: Always listen for the “chirp” and be  
prepared for speed and/or incline changes. In  
some instances, the speed and/or incline may  
change before the personal trainer describes  
the change.  
Wire removed from  
AUDIO OUT jack  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If the speed or incline settings are too high or too  
low, you can manually override the settings by  
pressing the Speed or Incline buttons on the con-  
sole. However, when the next “chirp” is heard,  
the speed and/or incline will change to the  
next settings of the CD or video program.  
• Make sure that the audio cable is properly  
connected, that it is fully plugged in, and that  
it is not wrapped around a power cord.  
• If you are using your portable CD player and  
the CD skips, set the CD player on the floor or  
another flat surface instead of on the console.  
To stop the walking belt at any time, press the  
Stop button on the console. The time will begin to  
flash in the Pace/Time display. To restart the pro-  
gram, press the Start button or the Speed in-  
crease button. After a moment, the walking belt  
will begin to move at 1 mph. When the next  
“chirp” is heard, the speed and incline will  
change to the next settings of the CD or video  
program.  
Follow your progress with the LED track and  
the displays.  
5
See step 5 on page 11.  
Measure your heart rate if desired.  
See step 6 on page 12.  
6
7
8
When the CD or video program is completed, the  
walking belt will stop and the time will begin to flash  
in the Pace/Time display. Note: To use another  
CD or video program, press the Stop button or re-  
move the key and go to step 1 on page 21.  
Turn on the fan if desired.  
See step 7 on page 12.  
When you are finished exercising, remove the  
key from the console.  
Note: If the speed or incline of the treadmill  
does not change when a “chirp” is heard:  
See step 7 on page 14.  
• Make sure that the indicator on the iFIT.com  
button is lit and that the time is not flashing in  
the Pace/Time display. If the Pace/Time dis-  
play is flashing, press the Start button or the  
Speed increase button on the console.  
CAUTION: Always remove iFIT.com CDs and  
videocassettes from your CD player or VCR  
when you are finished using them.  
• Adjust the volume of your CD player or VCR.  
If the volume is too high or too low, the con-  
sole may not detect the program signals.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Return to the treadmill and stand on the foot  
rails. Find the clip attached to the key and slide  
the clip onto the waistband of your clothes.  
HOW TO USE PROGRAMS DIRECTLY FROM  
OUR WEB SITE  
7
When the on-screen countdown ends, the program  
will begin and the walking belt will begin to move.  
Hold the handrails, step onto the walking belt, and  
begin walking. During the program, an electronic  
“chirping” sound will alert you when the speed  
and/or incline of the treadmill is about to change.  
CAUTION: Always listen for the “chirp” and be  
prepared for speed and/or incline changes.  
programs directly from the internet. Additional options  
information.  
To use programs from our Web site, the treadmill must  
be connected to your home computer. See HOW TO  
CONNECT YOUR COMPUTER on page 20. In  
addition, you must have an internet connection and  
an internet service provider. A list of specific system re-  
quirements is found on our Web site.  
If the speed or incline settings are too high or too  
low, you can manually override the settings by  
pressing the Speed or Incline buttons on the con-  
sole. However, when the next “chirp” is heard,  
the speed and/or incline will change to the next  
settings of the program.  
Follow the steps below to use a program from our  
Web site.  
Insert the key into the console.  
To stop the walking belt at any time, press the  
Stop button on the console. The time will begin to  
flash in the Pace/Time display. To restart the pro-  
gram, press the Start button or the Speed in-  
crease button. After a moment, the walking belt  
will begin to move at 1 mph. When the next  
“chirp” is heard, the speed and incline will  
change to the next settings of the program.  
1
See HOW TO TURN ON THE POWER on page 11.  
Select the iFIT.com mode.  
2
To use an iFIT.com CD  
or video program, press  
the iFIT.com button.  
The indicator on the but-  
ton will light.  
When the program ends, the walking belt will stop  
and the time will begin to flash in the Pace/Time  
display. Note: To use another program, press the  
Stop button and go to step 5.  
Go to your computer and start an internet  
connection.  
3
Note: If the speed or incline of the treadmill  
does not change when a “chirp” is heard, make  
sure that the indicator on the iFIT.com button is  
lit and that the Pace/Time display is not flash-  
ing. In addition, make sure that the audio cable  
is properly connected, that it is fully plugged in,  
and that it is not wrapped around a power cord.  
Start your web browser, if necessary, and go to  
4
Follow the desired links on our Web site to se-  
lect a program.  
5
Read and follow the on-line instructions for using a  
program.  
Follow your progress with the LED track and  
the displays.  
8
9
Follow the on-line instructions to start the  
program.  
6
See step 5 on page 11.  
When you start the program, an on-screen count-  
down will begin.  
When you are finished exercising, remove the  
key from the console.  
See step 7 on page 14.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE INFORMATION MODE/DEMO MODE  
HOW TO ADJUST THE CUSHIONING SYSTEM  
The console features an information mode that keeps  
track of the total number of hours that the treadmill has  
been operated and the total number of miles or kilome-  
tres that the walking belt has moved. The information  
mode also allows you to switch the console from miles  
per hour to kilometres per hour. In addition, the infor-  
mation mode allows you to turn on and turn off the  
demo mode.  
The treadmill fea-  
tures a cushion-  
ing system that  
reduces the im-  
pact as you walk  
or run on the  
treadmill. To in-  
Adjustment  
Knob  
crease the firm-  
ness of the walk-  
ing platform, turn  
the adjustment  
knob counterclockwise. To decrease the firmness, turn  
the knob clockwise. Note: The faster you run on the  
treadmill, or the more you weigh, the firmer the  
walking platform should be.  
To select the information mode, hold down the Stop  
button while inserting the key into the console. When  
the information mode is selected, the following informa-  
tion will be shown:  
The Distance/Incline display  
will show the total number of  
miles (or kilometres) that the  
walking belt has moved.  
The Pace/Time display will  
show the total number of  
hours the treadmill has been  
used.  
An “E” for English miles or  
an “M” for metric kilometres  
will appear in the Speed dis-  
play. Press the Speed in-  
crease button to change the  
unit of measurement.  
IMPORTANT: The Calories/Pulse display should be  
blank. If a “d” appears in the display, the console is in  
the “demo” mode. This mode is intended to be used  
only when a treadmill is displayed in a store. When the  
console is in the demo mode, the power cord can be  
plugged in, the key can be removed from the console,  
and the displays and indicators on the console will au-  
tomatically light in a preset sequence, although the  
buttons on the console will not operate. If a “d” appears  
in the Calories/Pulse display when the information  
mode is selected, press the Speed decrease button  
so the display is blank.  
To exit the information mode, remove the key.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO FOLD AND MOVE THE TREADMILL  
HOW TO FOLD THE TREADMILL FOR STORAGE  
1
Before folding the treadmill, adjust the incline to the  
lowest position. If this is not done, the treadmill may be  
permanently damaged. Next, unplug the power cord.  
CAUTION: You must be able to safely lift 45 pounds (20  
kg) to raise, lower, or move the treadmill.  
1. Hold the treadmill in the locations shown at the right. To  
decrease the possibility of injury, bend your legs and  
keep your back straight. As you raise the treadmill,  
make sure to lift with your legs rather than your back.  
Raise the treadmill about halfway to the vertical position.  
2. Hold the treadmill frame firmly with your left hand. Using  
2
your right hand, pull the latch knob to the right and hold it.  
Raise the treadmill until the pin on the latch knob is  
aligned with the hole in the left handgrip. Then, release  
the latch knob. Make sure that the latch knob is fully  
released so that the pin is fully inserted into the hole  
in the left handgrip.  
Frame  
Latch  
Knob  
Latch  
Knob  
Pin  
To protect the floor or carpet from damage, place a  
mat under the treadmill. Keep the treadmill out of  
direct sunlight. Do not leave the treadmill in the stor-  
age position in temperatures above 85° Fahrenheit.  
Handgrip  
Pin  
Handgrip  
HOW TO MOVE THE TREADMILL  
Before moving the treadmill, convert the treadmill to the  
storage position as described above. Make sure that the  
pin on the latch knob is fully inserted into the hole in the  
left handgrip.  
1. Hold the handgrips and place one foot against one of the  
wheels.  
2. Tilt the treadmill back until it rolls freely on the wheels.  
Carefully move the treadmill to the desired location. To re-  
duce the risk of injury, use extreme caution while  
moving the treadmill. Do not attempt to move the  
treadmill over an uneven surface.  
Base  
3. Place one foot against a wheel, and carefully lower the  
treadmill until the base is resting in the storage position.  
Front Wheels  
HOW TO LOWER THE TREADMILL FOR USE  
1. See drawing 2 above. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left  
and hold it. Pivot the treadmill down until the frame is past the latch pin.  
2. See drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor.  
CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and  
follow the steps listed. If further assistance is needed, see the front cover of this manual.  
PROBLEM: The power does not turn on  
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor  
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor  
that meets all of the specifications described on page 9. Important: The treadmill is not compatible  
with GFCI-equipped outlets.  
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.  
c. Check the reset/off circuit breaker located on the  
c
treadmill frame near the power cord. If the switch  
protrudes as shown, the circuit breaker has tripped.  
To reset the circuit breaker, wait for five minutes  
Reset  
and then press the switch back in.  
Tripped  
PROBLEM: The power turns off during use  
SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see c.  
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.  
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for  
five minutes, and then plug it back in.  
c. Remove the key from the console. Reinsert the key fully into the console.  
d. If the treadmill still will not run, see the front cover of this manual.  
PROBLEM: The walking belt slows when walked on  
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.  
b. If the walking belt is overtightened, treadmill performance  
b
may decrease and the walking belt may be permanently  
damaged. Remove the key and UNPLUG THE POWER  
CORD. Using the included allen wrench, turn both rear  
roller adjustment bolts counterclockwise 1/4 of a turn.  
When the walking belt is properly tightened, you should  
be able to lift the edges of the walking belt 3 to 4 inches  
off the walking platform. Be careful to keep the walking  
belt centered. Plug in the power cord, insert the key, and  
run the treadmill for a few minutes. Repeat until the walk-  
ing belt is properly tightened.  
3–4”  
Rear Roller Adjustment Bolts  
c. If the walking belt still slows when walked on, see the front cover of this manual.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM: The walking belt is off-center or slips when walked on  
SOLUTION: a. If the walking belt is off-center, first remove the key and  
UNPLUG THE POWER CORD. If the walking belt has  
shifted to the left, use the allen wrench to turn the left  
rear roller bolt clockwise 1/2 of a turn; if the walking belt  
has shifted to the right, turn the left bolt counterclock-  
wise 1/2 of a turn. Be careful not to overtighten the walking  
belt. Plug in the power cord, insert the key, and run the  
treadmill for a few minutes. Repeat until the walking belt is  
centered.  
a
b. If the walking belt slips when walked on, first remove the  
key and UNPLUG THE POWER CORD. Using the allen  
wrench, turn both rear roller bolts clockwise, 1/4 of a turn.  
When the walking belt is correctly tightened, you should  
be able to lift each side of the walking belt 3 to 4 inches off  
the walking platform. Be careful to keep the walking belt  
centered. Plug in the power cord, insert the key, and care-  
fully walk on the treadmill for a few minutes. Repeat until  
the walking belt is properly tightened.  
b
PROBLEM: The displays of the console do not function properly  
SOLUTION: a. Remove the key from the console and UNPLUG THE  
POWER CORD. Next, remove the screws from the hood  
and carefully remove the hood. Locate the Reed Switch  
(17) and the Magnet (12) on the left side of the Pulley (11).  
Turn the Pulley until the Magnet is aligned with the Reed  
Switch. Make sure that the gap between the Magnet  
and the Reed Switch is about 1/8”. If necessary, loosen  
the indicated Screw (40), move the Reed Switch slightly,  
and then retighten the Screw. Re-attach the hood and run  
the treadmill for a few minutes to check for a correct speed  
reading.  
a
1/8”  
40  
11  
12  
17  
Top  
View  
PROBLEM: The chest pulse sensor does not function properly  
SOLUTION: a. If the chest pulse sensor does not function properly, see CHEST PULSE SENSOR TROU-  
BLESHOOTING on page 8.  
b
b. If the chest pulse sensor still does not function properly, the battery  
should be changed. To replace the battery, locate the battery cover  
on the back of the sensor unit. Insert a coin into the slot in the cover  
and turn the cover counterclockwise to the “open” position. Remove  
the cover.  
Battery Cover  
Battery  
Cover  
Remove the old battery from the sensor unit. Insert a new CR 2032  
battery, making sure that the writing is on top. In addition, make sure  
that the rubber gasket is in place in the sensor unit. Replace the bat-  
tery cover and turn it to the closed position.  
Battery  
Rubber  
Gasket  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXERCISE GUIDELINES  
ergy. Only after the first few minutes does your body  
begin to use stored fat calories for energy. If your goal  
is to burn fat, adjust the speed or incline of the tread-  
mill until your heart rate is near the lowest number in  
your training zone.  
WARNING:  
Before beginning this  
or any exercise program, consult your physi-  
cian. This is especially important for individu-  
als over the age of 35 or individuals with pre-  
existing health problems.  
For maximum fat burning, adjust the speed or incline  
of the treadmill until your heart rate is near the middle  
number in your training zone.  
The pulse sensors are not medical devices.  
Various factors, including the user's move-  
ment, may affect the accuracy of heart rate  
readings. The pulse sensors are intended  
only as exercise aids in determining heart rate  
trends in general.  
Aerobic Exercise  
If your goal is to strengthen your cardiovascular sys-  
tem, your exercise must be “aerobic.” Aerobic exercise  
is activity that requires large amounts of oxygen for  
prolonged periods of time. This increases the demand  
on the heart to pump blood to the muscles, and on the  
lungs to oxygenate the blood. For aerobic exercise,  
adjust the speed or incline of the treadmill until your  
heart rate is near the highest number in your training  
zone.  
The following guidelines will help you to plan your ex-  
ercise program. For more detailed exercise informa-  
tion, obtain a reputable book or consult your physician.  
EXERCISE INTENSITY  
Whether your goal is to burn fat or to strengthen your  
cardiovascular system, the key to achieving the  
WORKOUT GUIDELINES  
desired results is to exercise with the proper intensity.  
The proper intensity level can be found by using your  
heart rate as a guide. The chart below shows recom-  
mended heart rates for fat burning and aerobic exercise.  
Each workout should include the following three parts:  
A Warm-up—Start each workout with 5 to 10 minutes  
of stretching and light exercise. A proper warm-up in-  
creases your body temperature, heart rate and circula-  
tion in preparation for exercise.  
Training Zone Exercise—After warming up, increase  
the intensity of your exercise until your pulse is in your  
training zone for 20 to 60 minutes. (During the first few  
weeks of your exercise program, do not keep your  
pulse in your training zone for longer than 20 minutes.)  
Breathe regularly and deeply as you exercise—never  
hold your breath.  
To find the proper heart rate for you, first find your age  
near the bottom of the chart (ages are rounded off to  
the nearest ten years). Next, find the three numbers  
above your age. The three numbers define your “train-  
ing zone.” The lower two numbers are recommended  
heart rates for fat burning; the highest number is the  
recommended heart rate for aerobic exercise.  
A Cool-down—Finish each workout with 5 to 10 min-  
utes of stretching to cool down. This will increase the  
flexibility of your muscles and will help prevent post-ex-  
ercise problems.  
EXERCISE FREQUENCY  
To measure your heart rate during exercise, use the  
handgrip pulse sensor or the chest pulse sensor.  
To maintain or improve your condition, complete three  
workouts each week, with at least one day of rest be-  
tween workouts. After a few months, you may com-  
plete up to five workouts each week if desired. The key  
to success is to make exercise a regular and enjoyable  
part of your everyday life.  
Fat Burning  
To burn fat effectively, you must exercise at a relatively  
low intensity level for a sustained period of time.  
During the first few minutes of exercise, your body  
uses easily accessible carbohydrate calories for en-  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED STRETCHES  
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.  
1. Toe Touch Stretch  
Stand with your knees bent slightly and slowly bend forward from  
your hips. Allow your back and shoulders to relax as you reach  
down toward your toes as far as possible. Hold for 15 counts,  
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees  
and back.  
1
2. Hamstring Stretch  
Sit with one leg extended. Bring the sole of the opposite foot to-  
ward you and rest it against the inner thigh of your extended leg.  
Reach toward your toes as far as possible. Hold for 15 counts,  
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,  
lower back and groin.  
2
3. Calf/Achilles Stretch  
With one leg in front of the other, reach forward and place your  
hands against a wall. Keep your back leg straight and your back  
foot flat on the floor. Bend your front leg, lean forward and move  
your hips toward the wall. Hold for 15 counts, then relax. Repeat  
3 times for each leg. To cause further stretching of the achilles  
tendons, bend your back leg as well. Stretches: Calves, achilles  
tendons and ankles.  
3
4
4. Quadriceps Stretch  
With one hand against a wall for balance, reach back and grasp  
one foot with your other hand. Bring your heel as close to your  
buttocks as possible. Hold for 15 counts, then relax. Repeat 3  
times for each leg. Stretches: Quadriceps and hip muscles.  
5. Inner Thigh Stretch  
Sit with the soles of your feet together and your knees outward.  
Pull your feet toward your groin area as far as possible. Hold for  
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and  
hip muscles.  
5
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PART LIST—Model No. IMTL11905.0  
R1005A  
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.  
Key No. Qty.  
Description  
Key No. Qty.  
Description  
1
2
3
4
5
6
7
8
2
1
1
4
1
1
2
1
2
4
1
1
8
2
2
1
1
1
2
2
14  
1
1
1
1
1
4
1
1
1
1
2
1
1
1
1
1
1
1
70  
1
2
11  
2
1
1
1
2
2
1
Foot Rail  
Left Outside Housing  
Audio Wire  
Isolator  
Latch Housing Cover  
Platform  
Walking Platform Screw  
Walking Belt  
Frame Pivot Bolt  
Frame Pivot Washer  
Front Wheel/Pulley  
Magnet  
Front Roller Nut/Front Wheel Nut  
Spacer Insert  
Frame Pivot Spacer  
Reed Switch Clip  
Reed Switch  
Lift Frame  
Foot Rail Insert  
Gear Rack  
Foot Rail Screw  
Motor Belt  
Pulse Receiver  
Drive Motor  
Transformer  
Chest Pulse Strap  
Hood Bracket  
51*  
52  
53  
54  
55  
56  
57  
58  
59*  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
100  
2
2
2
1
1
1
2
1
1
1
1
4
1
1
1
4
1
1
4
1
1
1
2
1
2
2
2
2
1
1
1
1
2
4
1
1
1
2
1
1
1
1
2
1
2
1
5
2
1
1
Cushion Assembly  
Roller Adj. Washer  
Rear Roller Adjustment Bolt  
Left Rear Endcap  
Frame  
Allen Wrench  
Rear Platform Screw  
Rear Roller  
Idler Assembly  
Audio Wire Nut  
Pulse Bar  
Spring Nut  
Idler Arm  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
Idler Spring  
Upright/Base  
Belt Guide Screw  
Console Frame  
Latch Housing  
Console Washer  
Left Handgrip, Bottom  
Console Wire Harness  
iFIT.com Wire  
Incline Pivot Bolt  
Hood Cover  
Spring  
Spring Pad Screw  
Front Wheel  
Wheel Bolt  
Pulley Nut  
Ground Wire  
Chest Pulse Sensor  
Right Rear Endcap  
Lift Motor Bolt  
Motor Bolt  
Outlet Bracket  
Left Inside Housing  
Right Inside Housing  
Right Outside Housing  
Controller  
Controller Bracket  
Motor Hood  
3/4” Screw  
Motor Belly Pan  
Belt Guide  
3/4” Tek Screw  
Spring Plate  
Console  
Console Base  
Fan  
Spring Pad  
Belly Pan Screw  
Upright Wire Harness  
Shock  
Left Handgrip, Top  
Upright Endcap  
Filter Wire  
Latch Warning Decal  
Incline Motor  
Right Handgrip, Top  
Fan Screw  
Right Handgrip, Bottom  
Tie Holder  
Tie  
8” Cable Tie  
Base Pad  
Left Front Endcap  
Right Front Endcap  
Ground Screw  
Rear Foot  
1/2” Tek Screw  
Book Holder  
Idler Arm Bolt  
Reset/Off Circuit Breaker  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Key No. Qty.  
Description  
Key No. Qty.  
Description  
101  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118*  
119  
120  
121  
122  
1
1
1
2
2
1
1
2
1
1
1
2
1
2
1
4
1
1
4
2
2
1
Pulse Wire  
Power Cord  
Power Cord Grommet  
Warning Decal  
Spring Plate  
123  
124  
125  
126  
127  
128  
129  
130  
131  
132  
133  
134  
135  
136  
#
2
1
1
2
1
2
2
1
5
2
4
4
1
1
1
1
1
1
Cushion Adj. Rod  
Incline Bracket  
Incline Motor Bolt (Bottom)  
Controller Screw  
Key/Clip  
Cushion Adj. Gear  
Cushion Adj. Wheel  
Cushion Adj. Knob  
Cushion Adj. Screw  
1/2” Screw  
Jack  
iFIT.com Audio Cable  
Rear Roller Star Washer  
Pulley Washer  
Idler Pulley  
Pulley Spacer  
Outlet Bracket Star Washer  
Static Decal  
Wheel Housing  
Idler Pulley Bolt  
Spring Washer  
Console Back  
Latch Assembly  
Spring Bolt  
Cushion Adj. Pin  
Motor Bushing  
Idler Arm Nylon Washer  
Console Bolt  
Pulse Bar Screw  
Access Door  
Fan Housing  
8” Blue Wire, 2 F  
4” Blue Wire, 2 F  
Blue Wire, M/F  
User’s Manual  
#
#
#
* Includes all parts shown in the box  
# These parts are not illustrated  
Specifications are subject to change without notice  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO ORDER REPLACEMENT PARTS  
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give  
the following information:  
• The MODEL NUMBER of the product (IMTL11905.0)  
• The NAME of the product (IMAGE ADVANCED 2400 treadmill)  
• The SERIAL NUMBER of the product (see the front cover of this manual)  
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING in the center of  
this manual and the PART LIST on pages 30 and 31)  
LIMITED WARRANTY  
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and  
material under normal use and service conditions. The drive motor is warranted for twenty (20) years  
after the date of purchase. Parts and labor are warranted for one (1) year after the date of purchase.  
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to  
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All re-  
pairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a  
service center, freight charges to and from the service center will be the customer’s responsibility. For in-  
home service, the customer will be responsible for a minimal trip charge. This warranty does not extend  
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, im-  
proper or abnormal usage or repairs not provided by an ICON authorized service center; products used  
for commercial or rental purposes; or products used as store display models. No other warranty beyond  
that specifically set forth above is authorized by ICON.  
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-  
nection with the use or performance of the product or damages with respect to any economic loss, loss  
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other  
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-  
cidental or consequential damages. Accordingly, the above limitation may not apply to you.  
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of  
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set  
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the  
above limitation may not apply to you.  
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.  
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813  
Part No. 234254 R1005A  
Printed in USA © 2005 ICON IP, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Car Seat Child Restraint Booster Seat User Manual
Grizzly Welder H8154 User Manual
HannsG Computer Monitor JW197D User Manual
Harbor Freight Tools Vacuum Cleaner 94683 User Manual
Hasbro Handheld Game System 71 554 User Manual
Honeywell Cordless Telephone D7900 User Manual
Hotpoint Washer Wml 721 User Manual
HP Hewlett Packard Cell Phone rw6800 User Manual
HP Hewlett Packard Network Card Console Management Controller User Manual
Hubbell Work Light UE24 User Manual