Model No. IMBE53901
Serial No.
USER’S MANUAL
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
you complete satisfaction
through direct assistance from
our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
11. The weight bench is designed to support a
maximum of 550 pounds, including the user,
a barbell, and weights. Do not place more
than 300 pounds, including the barbell, on
the weight gliders and safety spotters.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
12. Always set both safety spotters at the same
height.
3. The weight bench is intended for home use
only. Do not use the weight bench in a com-
mercial, rental, or institutional setting.
13. Always wear athletic shoes for foot protec-
tion while exercising.
4. Use the weight bench only on a level surface. 14. Always move the bench out of the way when
Cover the floor beneath the weight bench to
protect the floor.
performing an exercise that does not use the
bench.
5. Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately.
15. The decals shown below have been placed
on the weight bench. If a decal is missing or
illegible, please call our Customer Service
Department toll-free at 1-800-999-3756,
Monday through
6. Keep children under 12 and pets away from
the weight bench at all times.
Friday, 6 a.m. until 6
p.m. Mountain Time,
to order a free
replacement decal.
Apply the decal in the
location shown on
page 4.
!
WARNING
7. Keep hands and feet away from moving
parts.
• Misuse of this
product may result in
serious injury.
8. Always secure your weights (not included)
with weight clips when they are mounted on
the barbell.
• Read user’s manual
and follow all warnings
and operating instruc-
tions prior to use.
• Do not allow children
on or around machine.
9. Always make sure that there is an equal
amount of weight on each side of the barbell.
Keep hands and
fingers clear of
this area.
• Replace label if
damaged, illegible,
or removed.
10. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
Decal 1
Decal 2
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the versatile IMAGE® 4.5
toll-free at 1-800-999-3756, Monday through Friday, 6
weight bench. The IMAGE® 4.5 is designed to help you a.m. until 6 p.m. Mountain Time (excluding holidays).
develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic mus-
cle size and strength, or a healthier cardiovascular
To help us assist you, please note the product model
number and serial number before calling. The model
number is IMBE53901. The serial number can be
system, the IMAGE® 4.5 will help you achieve the spe- found on a decal attached to the weight bench (see
cific results you want.
the front cover of this manual).
For your benefit, read this manual carefully before
using the IMAGE® 4.5. If you have additional ques-
tions, please call our Customer Service Department
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Note: The terms “right side” and “left side”
are determined relative to a person sitting
on the bench; they do not refer to right and
left on the drawings in this manual.
Pull-up Bar
Right Side
Weight Guide
Left Side
Upright
Barbell
Dumbbell
Storage
Rack
Weight Glider
Weight
Storage
Tube
Safety Spotter
Backrest
Seat
Backrest
Adjustment
Bracket
Leg Lever
Warning Decal 2
Warning Decal 1
Curl Pad
Warning Decal 1 has been placed in the indi-
cated position, on both sides of the bench.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
R1200A
Part Identification Chart—Model No. IMBE53901
M6 x 16mm Screw (3)
M8 x 20mm Bolt (75)
M10 Washer (6)
Large Washer (70)
M10 x 25mm Bolt (76)
M6 Washer (30)
M8 Washer (77)
M10 x 25mm Button Head Bolt (69)
M8 x 30mm Bolt (64)
M6 x 35mm Bolt (34)
M10 Nylon Locknut (11)
M8 Nylon Locknut (42)
M6 x 55mm Screw (4)
M8 x 60mm Bolt (65)
M10 x 60mm Button Head Bolt (12)
M8 x 65mm Carriage Bolt (71)
M10 x 65mm Bolt (68)
M10 x 70mm Bolt (21)
M10 x 65mm Carriage Bolt (66)
M8 x 70mm Bolt (41)
M10 x 80mm Bolt (31)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Before beginning assembly, carefully read the
following information and instructions:
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
In addition to the included allen wrench
assembly requires the following tools (not
included):
,
Make Things Easier for Yourself!
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. By setting aside plenty of time, and
by deciding to make the task enjoyable,
assembly will go smoothly.
• Two (2) adjustable wrenches
• One (1) rubber mallet
• Assembly requires two people.
• One (1) standard screwdriver
• One (1) phillips screwdriver
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches or a set of ratchet wrenches.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5. Note:
Some small parts may be pre-assembled.
1. Before beginning, make sure that you understand
the information in the box above. Note: Some
parts described in the assembly steps may be
pre-assembled.
1
Decal
42
20
54
42
50
Press a 50mm Square Outer Cap (20) onto each end
of a Base (46). Turn the Base so the large hole is in
the position shown. Insert two M8 x 65mm Carriage
Bolts (71) and two M10 x 65mm Carriage Bolts (66)
up into the indicated holes in the Base. Place the
Base flat on the floor.
Large Hole
41
46
20
71
Turn the Base Crossbar (54) so the warning decal is
on top. Attach the Base (46) to the Base Crossbar
with two M8 x 70mm Bolts (41), a Large Support
Plate (50), and two M8 Nylon Locknuts (42). Do not
tighten the Nylon Locknuts yet.
66
2
20
50
41
2. Press a 50mm Square Outer Cap (20) onto each end
of the other Base (46). Turn the Base so the large
hole is in the position shown. Insert two M8 x 65mm
Carriage Bolts (71) and two M10 x 65mm Carriage
Bolts (66) up into the indicated holes in the Base.
Place the Base flat on the floor.
42
Large Hole
46
42
20
71
Attach the Base (46) to the Base Crossbar (54) with
two M8 x 70mm Bolts (41), a Large Support Plate
(50), and two M8 Nylon Locknuts (42). Do not tighten
the Nylon Locknuts yet.
54
66
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Slide a Brace (44) onto the bracket on one of the
Uprights (43). Attach the Brace to the Upright with
two M10 x 65mm Bolts (68), four M10 Washers (6),
and two M10 Nylon Locknuts (11). Do not tighten
the Nylon Locknuts yet.
3
43
6
Slide the Upright (43) and the Brace (44) onto the
M10 x 65mm Carriage Bolts (66) and the M8 x 65mm
Carriage Bolts (71) in the left Base (46). Attach the
Upright with two M10 Nylon Locknuts (11). Attach the
Brace with two M8 Washers (77) and two M8 Nylon
Locknuts (42). Do not tighten the Nylon Locknuts
yet.
11
44
6
Repeat this step on the right Base (46) with the other
Upright (43) and Brace (44).
68
42
Bracket
77
11
66
71
46
4. Press a 25mm Round Inner Cap (39) into the end of
a Weight Storage Tube (55).
4
44
While a second person holds the Middle Crossbar
(47) in the position shown, insert two M10 x 70mm
Bolts (21) through the bracket on the Weight Storage
Tube (55), the left Brace (44), and the bracket on the
Middle Crossbar. Thread an M10 Nylon Locknut (11)
onto each Bolt. Do not tighten the Nylon Locknuts
yet.
47
55
21
11
21
39
5. Press a 25mm Round Inner Cap (39) into the end of
the other Weight Storage Tube (55).
39
5
21
55
While a second person continues to hold the Middle
Crossbar (47), insert two M10 x 70mm Bolts (21)
through the bracket on the Weight Storage Tube (55),
the right Brace (44), and the bracket on the Middle
Crossbar. Thread an M10 Nylon Locknut (11) onto
each Bolt. Do not tighten the Nylon Locknuts yet.
21
47
44
11
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Have a second person hold the Top Crossbar (48) so
that the pull-up bar faces away from the rack, as
shown.
6
11
21
Attach the Top Crossbar (48) to the left Upright (43)
with two M10 x 70mm Bolts (21), a Small Support
Plate (51), and two M10 Nylon Locknuts (11). Do not
tighten the Nylon Locknuts yet.
51
48
11
11
21
Attach the Top Crossbar (48) to the right Upright (43)
with two M10 x 70mm Bolts (21), a Small Support
Plate (51), and two M10 Nylon Locknuts (11). Do not
tighten the Nylon Locknuts yet.
Pull-up
Bar
11
51
21
43
43
21
7. Press a 25mm Bushing (73) into each end of the
Locking Bar (62).
7
Insert the Barbell (63) through the Locking Bar (62)
until the Barbell is centered in the Locking Bar.
73
62
63
73
8. Identify the Left Weight Glider (60) by looking at the
position of the round tube.
8
Press a 38mm Bushing (58) into each end of the
round tube on the Left Weight Glider (60).
Slide the Left Weight Glider (60) onto the left end of
the Barbell (63). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 20mm Bolt (75).
Look at the drawing on page 4 to make sure that
you have correctly identified the left end. The Left
Weight Glider must be turned as shown in the
drawing.
60
58
63
75
58
Repeat this step with the Right Weight Glider (not
shown).
Round tube
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Identify the Left Safety Spotter (57) by the position of
the handle and the Left Spotter Hook (45). Place the
Left Safety Spotter on the left Base (46) so it is cen-
tered over the indicated hole.
9
53
Have a second person hold the Locking Bar (62) so
that the Left Weight Glider (60) rests on top of the
Left Safety Spotter (57). Insert a Weight Guide (53)
into the Left Weight Glider, the Left Safety Spotter,
and the hole in the Base (46). Note: Tilt the Weight
Guide away from the Upright (43) as you insert it.
43
62
60
Handle
Attach the Weight Guide (53) to the Base (46) with an
M8 x 60mm Bolt (65), two M8 Washers (77), and an
M8 Nylon Locknut (42). Do not tighten the Nylon
Locknut yet.
45
57
46
42
77
Hole
65
10. Place the Right Safety Spotter (56) on the right Base
(46) and center it over the indicated hole. Note: The
handle must point toward the center of the rack.
10
Have a second person hold the Locking Bar (62) so
that the Right Weight Glider (59) rests on top of the
Right Safety Spotter (56). Insert a Weight Guide (53)
into the Right Weight Glider, the Right Safety Spotter,
and the hole in the Base (46). Note: Tilt the Weight
Guide away from the Upright (43) as you insert it.
53
59
1
Attach the Weight Guide (53) to the Base (46) with an
M8 x 60mm Bolt (65), two M8 Washers (77), and an
M8 Nylon Locknut (42). Do not tighten the Nylon
Locknut yet.
46
Handle
56
65
11. Note: If you are not planning to use Olympic
weights with the weight rack, you do not need to
perform this step. Keep the two Weight Adapters
(61) in a safe place in case you need them in the
future.
Hole
77
62
42
Fully engage the indicated hook on both sides of
the weight rack before beginning this step.
11
Insert a 50mm Bushing (72) into the end of a Weight
Adapter (61). With a second person holding the
Barbell (63) so that it cannot turn, use the allen
wrench to secure the Weight Adapter to the Barbell
with a Large Washer (70) and an M10 x 25mm Button
Head Bolt (69). Note: The Large Washer must fit
into the indentation in the 50mm Bushing in the
Weight Adapter.
Hook
63
61
72
70
Pull the remaining length of the Barbell (63) in the
direction shown. Next, tighten the M8 x 20mm
Screws used in steps 9 and 10. Attach the other
Weight Adapter (61) to the other end of the Barbell in
the same manner.
69
9
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Attach the upper end of one of the Weight Guides
(53) to the bracket on the Upright (43) with an M8 x
30mm Bolt (64) and an M8 Washer (77).
12
64
Attach the other Weight Guide (53) to the other
Upright (43) in the same manner.
77
Tighten all of the Nylon Locknuts used in steps 1
to 12.
53
43
13. Press a 50mm x 70mm Outer Cap (10) onto each
end of the Stabilizer (13).
13
11
13
Attach the Stabilizer (13) to the Bench Frame (5)
with two M10 x 60mm Button Head Bolts (12) and
two M10 Nylon Locknuts (11). Note: Position the
Stabilizer so that the warning decal is in the
position shown.
10
5
Decal
Note: Do not tighten the Nylon Locknuts yet.
12
10
14. Press a 50mm Square Outer Cap (20) onto each
end of the Bench Base (7).
Welded Nut
1
14
6
Attach the Bench Base Joint Plate (19) to the Bench
Base (7) with two M10 x 70mm Bolts (21), two M10
Washers (6), and two M10 Nylon Locknuts (11).
21
6
11
7
6
Attach the Bench Leg (1) to the Bench Base Joint
Plate (19) with two M10 x 70mm Bolts (21), two M10
Washers (6), and two M10 Nylon Locknuts (11).
19
20
Be sure the welded nut is in the position shown.
Note: Do not tighten the Nylon Locknuts yet.
6
21
20
15. Attach the Bench Leg (1) to the Bench Frame (5)
with two Bench Joint Plates (18), four M10 x 70mm
Bolts (21), and four M10 Nylon Locknuts (11).
15
21
18
5
Note: Tighten all the Nylon Locknuts used in
steps 13-15.
18
1
11
10
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Press two 25mm x 40mm Inner Caps (28) into each
Backrest Tube (27). Press two 25mm x 40mm Inner
Caps into the Backrest Adjustment Bracket (35).
16
Lubricate
28
27
6
22
Holes
Lubricate an M10 x 190mm Bolt (22). Attach the
Backrest Tubes (27) to the welded tube on the
Backrest Adjustment Bracket (35) with the Bolt, two
M10 Washers (6), and an M10 Nylon Locknut (11).
Make sure that the Backrest Tubes are turned as
shown. The indicated holes are not centered in
the Backrest Tubes but are closer to one side.
Turn the Backrest Tubes so the holes are closer
to the floor. Do not over tighten the Nylon
11
6
28
35
Welded
Tube
28
Locknut; the Backrest Tubes must pivot easily.
17. Lubricate an M10 x 190mm Bolt (22). Attach the
Backrest Tubes (27) to the welded tube on the
Bench Frame (5) with the Bolt, two M10 Washers
(6), and an M10 Nylon Locknut (11). Note: Do not
over tighten the Nylon Locknut; the Backrest
Tubes must pivot easily.
17
Lubricate
6
22
6
27
Welded Tube
5
11
18. Attach the Backrest (15) to the Backrest Tubes (27)
with four M6 x 55mm Screws (4) and four M6
Washers (30).
18
15
27
19. See the inset drawing. Press the 20mm x 50mm Inner
Cap (33) into the open end of the Seat Mounting
Bracket (23).
30
See the inset drawing. Lubricate an M8 x 70mm Bolt
(41). Attach the Seat Adjustment Bracket (36) to the
indicated side of the Seat Mounting Bracket (23) with
the Bolt and an M8 Nylon Locknut (42). Note: Do not
over tighten the Nylon Locknut; the Seat
4
19
23
Adjustment Bracket must pivot easily.
Place the Seat Mounting Bracket (23) on the Bench
Frame (5) so that the Seat Adjustment Bracket (36)
fits over the welded pin on the side of the Bench
Frame.
36
Lubricate
31
Lubricate
41
Lubricate an M10 x 80mm Bolt (31). Attach the Seat
Mounting Bracket (23) to the indicated bracket on the
Bench Frame (5) with the Bolt and a M10 Nylon
Locknut (11). Note: Do not over tighten the Nylon
Locknut; the Seat Mounting Bracket must pivot
easily.
23
36
Welded
Pin
5
11
42
33
11
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Turn the Seat (14) as shown. Attach the wide end
of the Seat to the bracket on the Seat Mounting
Bracket (23) with two M6 x 16mm Screws (3).
20
14
Tilt the Seat Mounting Bracket (23) upwards and
attach the narrow end of the Seat (14) to the Seat
Mounting Bracket with an M6 x 35mm Bolt (34) and
an M6 Washer (30).
Bracket
23
30
3
34
21. Attach the Adjustable Bench Leg (2) to the Bench
Leg (1) with the Adjustment Knob (37).
21
40
2
Insert a 45mm Square Inner Cap (40) into the top
of the Adjustable Bench Leg (2).
37
1
22. Insert three 45mm Square Inner Caps (40) into the
ends of the Leg Lever (17). Insert a 25mm Round
Inner Cap (39) into the weight tube on the Leg Lever.
Press a 25mm Angled Outer Cap (38) onto the other
end of the weight tube.
22
21
40
2
Attach the Leg Lever (17) to the Adjustable Bench
Leg (2) with an M10 x 70mm Bolt (21) and an M10
Nylon Locknut (11). Note: Do not over tighten the
M10 Nylon Locknut; the Leg Lever must pivot
easily.
40
11
Weight
Tube
38
39
17
2
40
23. Insert 19mm Round Inner Caps (26) into the ends of
the three Pad Tubes (16).
23
25
26
25
Insert two Pad Tubes (16) through the holes in the
Leg Lever (17). Slide a Foam Pad (25) onto each
side of the Pad Tubes.
16
26
Insert a Pad Tube (16) through the upper tube on the
Adjustable Bench Leg (2). Slide a Foam Pad (25)
onto each side of the Pad Tube.
25
25
17
26
25
12
Download from Www.Somanuals.com. All Manuals Search And Download.
24. Attach the Curl Pad (8) to the Curl Upright (9) with
two M6 x 16mm Screws (3).
24
8
3
25. Make sure all parts are properly tightened before
you use the weight bench. The use of all remaining
parts will be explained in ADJUSTING THE WEIGHT
BENCH starting on the following page.
9
Adjusting the Weight Bench
This section explains how the weight bench can be adjusted. See the included exercise guide for important
information about how to perform a variety of exercises and how to get the greatest benefit from your exercise
program. Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately.
The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE LOCKING BAR AND SAFETY SPOTTERS
Before starting an exercise, position the Barbell (63) and
the Safety Spotters (56, 57) in the correct position for that
exercise.
43
43
To do this, stand in front of the cage and grip the Locking
Bar (62) with both hands. Turn the Locking Bar until the
two hooks disengage the slots in the Uprights (43). Move
the Locking Bar to a new position and turn the Locking
Bar until the hooks engage the slots in the Uprights.
Note: Always start an exercise with the Barbell posi-
tioned at the lowest point to which it will move during
the exercise.
59
56
62
63
60
57
Position both Safety Spotters (56, 57) directly under the
Weight Gliders (59, 60).
USING THE SAFETY SPOTTERS
To move a Safety Spotter (56, 57) to a new position, grip
the handle on one side of the Spotter Hook (49, 45 [not
shown]) and pull the Spotter Hook out of the slot in the
Upright (43). Raise or lower the Safety Spotter to a new
position and turn the Spotter Hook until it engages one of
the slots in the Upright.
43
49
Handle
56
WARNING:
Always set both Safety
Spotters (56, 57) at the same height.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WEIGHTS TO THE BARBELL
To use the Barbell (63), slide the desired amount of
weight (not included) onto each end of the Barbell.
Secure the weights with the Large Weight Clips (67).
Note: To use standard weights, the Weight Adapters (61)
should be removed from the Barbell. Attach weights to
the Barbell with the Small Weight Clips (not shown).
61
63
67
WARNING:
Do not place more than
260 pounds on the Barbell (63). Always secure
the weights with Weight Clips (67) when they are
on the Barbell. Always place the same amount of
weight on each side of the Barbell.
15
14
ADJUSTING THE PAD TUBES
16
2
For some exercises, it may be necessary to move the
Pad Tube (16) in the Adjustable Bench Leg (2). To do
this, remove a Foam Pad (25) from one side of the Pad
Tube. Slide the Pad Tube out of the Adjustable Bench
Leg. Reinsert the Pad Tube into the lower welded tube
on the Adjustable Bench Leg. Replace the Foam Pad
on the Pad Tube.
25
To do leg raise exercises, the Pad Tube (16) must be
moved to the lower welded tube, the narrow end of the
Seat (14) must be raised, and the Backrest (15) must
be declined as shown.
8
USING THE CURL PAD
To use the Curl Pad (8), unscrew the Adjustment Knob
(37) and lift the Leg Lever (17) out of the Bench Leg
(1). Insert the Curl Pad into the Bench Leg, and secure
it with the Adjustment Knob.
17
37
Note: When not using the Curl Pad (8), store it away
from the bench.
1
USING OLYMPIC WEIGHTS ON THE LEG LEVER
To use Olympic weights on the Leg Lever (17), insert
the Weight Adapter Bushings (24) into the ends of the
Weight Adapter (32). Slide the Weight Adapter over the
weight tube on the Leg Lever. Insert the Weight Adapter
Pin (29) into the weight tube.
17
32
29
WARNING:
Do not place more than
150 pounds on the Leg Lever (17).
24
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE SEAT
To raise the Seat (14), lift the narrow end of the Seat
until the appropriate tab on the Seat Adjustment
Bracket (36) engages the welded pin (not shown) on
the right side of the Bench Frame (5).
To lower the Seat (14), use the handle on the Seat
Adjustment Bracket (36) to disengage the Seat
Adjustment Bracket from the pin on the right side of the
Bench Frame (5). Lower the Seat to the desired posi-
tion and engage the appropriate tab on the Seat
Adjustment Bracket to the pin.
36
Handle
Pin
14
5
ADJUSTING THE BACKREST
15
To raise the Backrest (15), grip the end of the Backrest
with one hand and pull it upward until the Backrest
Adjustment Bracket (35) locks into the appropriate tab
on the bracket on the Bench Frame (5).
Handle
35
To lower the Backrest (15), grip the end of the Backrest
with one hand and pull it slightly upwards. Grip the handle
(not shown) on the right side of the Backrest Adjustment
Bracket (35) with your other hand and pull the Backrest
Adjustment Bracket free of the tabs on the bracket on the
Bench Frame (5). Lower the Backrest to the desired posi-
tion and lock the Backrest Adjustment Bracket into the
desired tab on the Bench Frame bracket.
5
Bracket
WARNING:
Be sure that the
Backrest Adjustment Bracket (35) is securely
locked to the Bench Frame (5) before using the
weight bench.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
• The MODEL NUMBER of the product (IMBE53901)
• The NAME of the product (IMAGE® 4.5 weight bench)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 172540 R1200A
Printed in China © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART LIST/EXPLODED DRAWING
FROM THE MANUAL
SAVE THIS PART LIST/EXPLODED DRAWING AND THE USER’S MANUAL
FOR FUTURE REFERENCE
81
Download from Www.Somanuals.com. All Manuals Search And Download.
R1200A
Part List—Model No. IMBE53901
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
4
4
1
16
1
1
1
2
32
2
1
1
1
3
1
2
1
6
17
2
1
2
6
6
2
6
1
5
1
1
1
1
1
1
1
1
3
4
Bench Leg
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
#
5
11
2
2
1
2
1
1
1
2
2
2
2
1
2
1
1
4
1
1
2
1
1
2
2
4
2
4
2
2
4
2
2
8
2
2
10
1
1
1
M8 x 70mm Bolt
M8 Nylon Locknut
Upright
Brace
Left Spotter Hook
Base
Adjustable Bench Leg
M6 x 16mm Screw
M6 x 55mm Screw
Bench Frame
M10 Washer
Bench Base
Curl Pad
Curl Upright
50mm x 70mm Outer Cap
M10 Nylon Locknut
M10 x 60mm Button Head Bolt
Stabilizer
Middle Crossbar
Top Crossbar
9
Right Spotter Hook
Large Support Plate
Small Support Plate
Small Weight Clip
Weight Guide
Base Crossbar
Weight Storage Tube
Right Safety Spotter
Left Safety Spotter
38mm Bushing
Right Weight Glider
Left Weight Glider
Weight Adapter
Locking Bar
Barbell
M8 x 30mm Bolt
M8 x 60mm Bolt
M10 x 65mm Carriage Bolt
Large Weight Clip
M10 x 65mm Bolt
M10 x 25mm Button Head Bolt
Large Washer
M8 x 65mm Carriage Bolt
50mm Bushing
25mm Bushing
45mm x 45mm Bushing
M8 x 20mm Bolt
M10 x 25mm Bolt
M8 Washer
User’s Manual
Exercise Guide
6mm Allen Wrench
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Seat
Backrest
Pad Tube
Leg Lever
Bench Joint Plate
Bench Base Joint Plate
50mm Square Outer Cap
M10 x 70mm Bolt
M10 x 190mm Bolt
Seat Mounting Bracket
Weight Adapter Bushing
Foam Pad
19mm Round Inner Cap
Backrest Tube
25mm x 40mm Inner Cap
Weight Adapter Pin
M6 Washer
M10 x 80mm Bolt
Weight Adapter
20mm x 50mm Inner Cap
M6 x 35mm Bolt
Backrest Adjustment Bracket
Seat Adjustment Bracket
Adjustment Knob
25mm Angled Outer Cap
25mm Round Inner Cap
45mm Square Inner Cap
#
#
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
R1200A
Exploded Drawing—Model No. IMBE53901
Download from Www.Somanuals.com. All Manuals Search And Download.
|