¨
Model No. IMBE41990
Serial No.
USERÕS MANUAL
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or find that there
are missing parts, we will guar-
antee you complete satisfaction
through direct assistance from
our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
WARNING: To reduce the risk of serious injury, read the following important precautions before
using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
barbell, on the weight gliders and safety
spotters.
12. Always set both safety spotters at the same
height.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
13. Always secure your weights (not included)
with weight clips when they are mounted on
the barbell.
3. The weight bench is intended for home use
only. Do not use the weight bench in a com-
mercial, rental or institutional setting.
14. Always move the bench out of the way when
performing an exercise that does not use the
bench.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.
15. The decals shown below have been placed
on the weight bench. If a decal is missing or
illegible, please call our Customer Service
Department toll-free at 1-800-999-3756,
5. Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately.
Monday through Friday, 6 a.m. until 6 p.m.
Mountain Time, to order a free replacement
decal. Apply the decal in the location shown.
6. Keep children under 12 and pets away from
the weight bench at all times.
7. Keep hands and feet away from moving
parts.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. Always make sure there is an equal amount
of weight (not included) on each side of the
barbell.
10. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
11. The weight bench is designed to support a
maximum of 560 pounds, including the user,
a barbell and weights (not included). Do not
place more than 310 pounds, including the
WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the versatile IMAGE¨ 3.8
Department toll-free at 1-800-999-3756, Monday
weight bench. The IMAGE¨ 3.8 is designed to help you through Friday, 6 a.m. until 6 p.m. Mountain Time
develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic mus-
cle size and strength, or a healthier cardiovascular
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is IMBE41990. The
system, the IMAGE¨ 3.8 will help you achieve the spe- serial number can be found on a decal attached to the
cific results you want.
IMAGE¨ 3.8 (see the front cover of this manual).
For your benefit, read this manual carefully before
using the IMAGE¨ 3.8 weight bench. If you have
additional questions, please call our Customer Service
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Note: The terms Òright sideÓ and Òleft sideÓ
are determined relative to a person sitting
on the bench. They do not refer to right
and left on the drawings in this manual.
Right Side
Weight Guide
Left Side
Upright
Barbell
Weight Glider
Weight
Storage
Tube
Safety Spotter
Backrest
Seat
Adjustment
Bracket
4
Download from Www.Somanuals.com. All Manuals Search And Download.
R1299A
Part Identification ChartÑModel No. IMBE41990
M6 x 55mm Bolt (4)Ñ4
M6 x 38mm Bolt (60)Ñ1
M6 x 16mm Screw (3)Ñ2
M6 Washer (30)Ñ5
M10 Washer (6)Ñ14
M8 Nylon Locknut (54)Ñ13
M8 Washer (52)Ñ10
M10 Nylon Locknut (11)Ñ24
M8 x 70mm Bolt (41)Ñ4
M10 x 25mm Bolt (43)Ñ2
M8 x 65mm Carriage Bolt (59)Ñ4
M10 x 65mm Carriage Bolt (40)Ñ8
M8 x 60mm Bolt (39)Ñ2
M10 x 65mm Bolt (42)Ñ4
M8 x 30mm Bolt (38)Ñ2
M10 x 70mm Bolt (46)Ñ8
M8 x 25mm Bolt (53)Ñ2
M10 x 80mm Bolt (56)Ñ1
M8 x 16mm Screw (50)Ñ2
M10 x 115mm Bolt (55)Ñ1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Before beginning assembly, carefully read the
following information and instructions:
¥ As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
In addition to the included allen wrench
assembly requires the following tools (not
included):
,
Make Things Easier for Yourself!
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. By setting aside plenty of time, and
by deciding to make the task enjoyable,
assembly will go smoothly.
¥ Two (2) adjustable wrenches
¥ One (1) rubber mallet
¥ Assembly requires two people.
¥ One (1) standard screwdriver
¥ One (1) phillips screwdriver
¥ Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
¥ Lubricant, such as grease or petroleum jelly,
and soapy water.
¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches or a set of ratchet wrenches.
¥ For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5. Note:
Some small parts may be pre-assembled.
1. Before beginning, make sure that you understand
the information in the box above. Note: Some
parts described in the assembly steps may be
pre-assembled.
1
Decal
54
17
20
54
12
Press a 50mm Square Outer Cap (17) onto each end
of a Base (7). Turn the Base so the large hole is in
the position shown. Insert two M8 x 65mm Carriage
Bolts (59) and two M10 x 65mm Carriage Bolts (40)
up into the indicated holes in the Base. Place the
Base flat on the floor.
Large Hole
41
7
17
59
Turn the Base Crossbar (20) so the warning decal is
positioned as shown. Attach the Base (7) to the Base
Crossbar with two M8 x 70mm Bolts (41), a Large
Support Plate (12), and two M8 Nylon Locknuts (54).
Do not tighten the Nylon Locknuts yet.
40
2
17
12
41
2. Press a 50mm Square Outer Cap (17) onto each end
of the other Base (7). Turn the Base so the large hole
is in the position shown. Insert two M8 x 65mm
Carriage Bolts (59) and two M10 x 65mm Carriage
Bolts (40) up into the indicated holes in the Base.
Place the Base flat on the floor.
54
20
Large Hole
7
54
17
59
Attach the Base (7) to the Base Crossbar (20) with
two M8 x 70mm Bolts (41), a Large Support Plate
(12), and two M8 Nylon Locknuts (54). Do not tighten
the Nylon Locknuts yet.
40
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Slide a Brace (2) onto the bracket on one of the
Uprights (1). Attach the Brace to the Upright with two
M10 x 65mm Bolts (42), four M10 Washers (6), and
two M10 Nylon Locknuts (11). Do not tighten the
Nylon Locknuts yet.
3
1
Slide the Upright (1) and the Brace (2) onto the M10
x 65mm Carriage Bolts (40) and the M8 x 65mm
Carriage Bolts (59) in the left Base (7). Attach the
Upright with two M10 Nylon Locknuts (11). Attach the
Brace with two M8 Washers (52) and two M8 Nylon
Locknuts (54). Do not tighten the Nylon Locknuts
yet.
11
6
2
6
42
Bracket
54
52
11
40
59
7
4. Slide the remaining Brace (2) onto the bracket on the
other Upright (1). Attach the Brace to the Upright with
two M10 x 65mm Bolts (42), four M10 Washers (6),
and two M10 Nylon Locknuts (11). Do not tighten
the Nylon Locknuts yet.
4
1
Slide the Upright (1) and the Brace (2) onto the M10
x 65mm Carriage Bolts (40) and the M8 x 65mm
Carriage Bolts (59) in the right Base (7). Attach the
Upright with two M10 Nylon Locknuts (11). Attach the
Brace with two M8 Washers (52) and two M8 Nylon
Locknuts (54). Do not tighten the Nylon Locknuts
yet.
42
6
2
11
6
Bracket
54
52
59
7
11
40
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Press a 25mm Round Inner Cap (51) into the end of
a Weight Storage Tube (21).
5
2
While a second person holds a Crossbar (8) in the
position shown, insert two M10 x 70mm Bolts (46)
through the bracket on the Weight Storage Tube (21),
the left Brace (2), and the bracket on the Crossbar
(8). Thread an M10 Nylon Locknut (11) onto each
Bolt. Do not tighten the Nylon Locknuts yet.
8
21
46
11
46
51
6. Press a 25mm Round Inner Cap (51) into the end of
the other Weight Storage Tube (21).
6
51
46
21
While a second person continues to hold the
Crossbar (8), insert two M10 x 70mm Bolts (46)
through the bracket on the Weight Storage Tube (21),
the right Brace (2), and the bracket on the Crossbar
(8). Thread an M10 Nylon Locknut (11) onto each
Bolt. Do not tighten the Nylon Locknuts yet.
46
2
8
11
7. Have a second person hold the other Crossbar (8).
7
Attach the Crossbar (8) to the left Upright (1) with
two M10 x 70mm Bolts (46), a Small Support Plate
(16), and two M10 Nylon Locknuts (11). Do not
tighten the Nylon Locknuts yet.
11
46
16
8
11
Attach the Crossbar (8) to the right Upright (1) with
two M10 x 70mm Bolts (46), a Small Support Plate
(16), and two M10 Nylon Locknuts (11). Do not
tighten the Nylon Locknuts yet.
11
46
11
16
46
1
1
46
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press a 25mm Bushing (48) into each end of the
Locking Bar (34).
8
Insert the Barbell (35) through the Locking Bar (34)
until the Barbell is centered in the Locking Bar.
48
34
35
48
9. Identify the Left Weight Glider (32) by looking at the
position of the round tube.
9
Press a 38mm Bushing (29) into each end of the
round tube on the Left Weight Glider (32).
32
29
Slide the Left Weight Glider (32) onto the left end of
the Barbell (35). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 16mm Screw (50).
Look at the drawing on page 4 to make sure that
you have correctly identified the left end. The Left
Weight Glider must be turned as shown in the
drawing.
35
50
29
Round tube
10. Identify the Right Weight Glider (31) by looking at the
position of the round tube.
10
29
50
Press a 38mm Bushing (29) into each end of the
welded tube on the Right Weight Glider (31).
29
Slide the Right Weight Glider (31) onto the right end
of the Barbell (35). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 16mm Screw (50).
Make sure that the Weight Glider is turned as
shown in the drawing.
35
Round
tube
31
11. Identify the Left Safety Spotter (24) by the position of
the handle and the Left Spotter Hook (62). Place the
Left Safety Spotter on the left Base (7) so it is cen-
tered over the indicated hole.
11
18
1
Have a second person hold the Locking Bar (34) so
that the Left Weight Glider (32) rests on top of the
Left Safety Spotter (24). Insert a Weight Guide (18)
into the Left Weight Glider, the Left Safety Spotter,
and the hole in the Base (7). Note: Tilt the Weight
Guide away from the Upright (1) as you insert it.
34
32
Handle
62
24
7
54
52
Attach the Weight Guide (18) to the Base (7) with an
M8 x 60mm Bolt (39), two M8 Washers (52), and an
M8 Nylon Locknut (54). Do not tighten the Nylon
Locknut yet.
Hole
39
9
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Place the Right Safety Spotter (23) on the right Base
(7) and center it over the indicated hole. Note: The
handle must point toward the center of the bench.
12
Have a second person hold the Locking Bar (34) so
that the Right Weight Glider (31) rests on top of the
Right Safety Spotter (23). Insert a Weight Guide (18)
into the Right Weight Glider, the Right Safety Spotter,
and the hole in the Base (7). Note: Tilt the Weight
Guide away from the Upright (1) as you insert it.
18
31
1
34
Attach the Weight Guide (18) to the Base (7) with an
M8 x 60mm Bolt (39), two M8 Washers (52), and an
M8 Nylon Locknut (54). Do not tighten the Nylon
Locknut yet.
23
Handle
7
39
52
Hole
54
13. Note: If you are not planning to use Olympic
weights, do not perform this step. Keep the two
Weight Adapters (33) in case you need them in
the future.
13
Fully engage the indicated hook on both sides of
the weight bench before beginning this step.
Insert a 50mm Bushing (47) into the end of a Weight
Adapter (33). With a second person holding the
Barbell (35) so that it cannot turn, use the allen
wrench to secure the Weight Adapter to the Barbell
with a Large Washer (44) and an M10 x 25mm Bolt
(43). Note: The Large Washer must fit into the
indentation in the 50mm Bushing (47) in the
Weight Adapter.
Hook
35
33
47
44
Pull the remaining length of the Barbell (35) in the
direction shown. Next, tighten the M8 x 16mm
Screws used in steps 9 and 10. Attach the other
Weight Adapter (33) to the other end of the Barbell
(35) in the same manner.
43
14. Attach the upper end of one of the Weight Guides
(18) to the bracket on the Upright (1) with an M8 x
30mm Bolt (38) and an M8 Washer (52).
14
38
Attach the other Weight Guide (18) to the other
Upright (1) in the same manner.
52
Tighten all of the Nylon Locknuts used in steps 1
to 14.
18
1
10
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Press a 50mm Square Outer Cap (17) onto each end
of the Small Stabilizer (25).
15
16
17
11
5
Attach the Small Stabilizer (25) to the Bench Frame
(5) with two M10 x 65mm Carriage Bolts (40) and two
M10 Nylon Locknuts (11). Note: There is an inden-
tation around the holes on one side of the Small
Stabilizer. This side must be facing the floor.
17
25
17
40
16. Press a 50mm x 70mm Outer Cap (10) onto each
end of the Large Stabilizer (26).
11
Turn the Large Stabilizer (26) so the warning decal is
in the position shown. Attach the Large Stabilizer to
the Bench Frame (5) with two M10 x 65mm Carriage
Bolts (40) and two M10 Nylon Locknuts (11). Note:
There is an indentation around the holes on one
side of the Large Stabilizer. This side must be fac-
ing the floor.
5
Decal
10
10
26
40
17. Press two 20mm x 40mm Inner Caps (28) into each
Backrest Tube (27). Press four 20mm x 40mm Inner
Caps into the Backrest Adjustment Bracket (36).
Lubricate
28
27
Lubricate an M10 x 180mm Bolt (22). Attach the
Backrest Tubes (27) to the welded tube on the
Backrest Adjustment Bracket (36) with the Bolt, two
M10 Washers (6), and an M10 Nylon Locknut (11).
Make sure that the Backrest Tubes are turned as
shown. The indicated holes are not centered in
the Backrest Tubes but are closer to one side.
Turn the Backrest Tubes so the holes are closer
to the floor. Do not overtighten the Nylon Locknut;
the Backrest Tubes must pivot easily.
22
6
6
Holes
11
28
28
Welded
Tube
28
36
18. Attach the Backrest Adjustment Bracket (36) to the
bracket on the Bench Frame (5) in the following way:
18
55
Lubricate an M10 x 115mm Bolt (55). Slide an M10
Washer (6) onto the Bolt and insert the Bolt through
the indicated tube of the Backrest Adjustment Bracket
(36).
27
Lubricate
36
Hold the Backrest Adjustment Bracket (36) over the
bracket on the Bench Frame (5). Insert the M10 x
115mm Bolt (55) through one side of the bracket.
Slide the 15mm x 10.2mm x 60mm Spacer (57) onto
the Bolt. Next, insert the Bolt through the other side of
the bracket and the other tube of the Backrest
Adjustment Bracket. Secure the Bolt with an M10
Washer (6) and an M10 Nylon Locknut (11). Do not
overtighten the Nylon Locknut.
6
57
11
6
Bracket
5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Lubricate an M10 x 180mm Bolt (22). Attach the
Backrest Tubes (27) to the indicated tube on the
Bench Frame (5) with the Bolt, two M10 Washers (6),
and an M10 Nylon Locknut (11). Note: Do not over-
tighten the Nylon Locknut; the Backrest Tubes
must pivot easily.
19
Lubricate
6
27
22
5
11
27
Tube
6
20. Attach the Backrest (15) to the Backrest Tubes (27)
with four M6 x 55mm Bolts (4) and four M6 Washers
(30).
20
15
30
4
30
30
9
4
21. Press a 25mm x 50mm Inner Cap (58) into the open
end of the Seat Support Tube (37).
21
45
Lubricate an M8 x 80mm Bolt (9). Attach the Seat
Adjustment Bracket (45) to the indicated side of the
Seat Support Tube (37) with the Bolt and an M8
Nylon Locknut (54). Note: Do not overtighten the
Nylon Locknut; the Seat Adjustment Bracket must
pivot easily.
37
Lubricate
54
58
22. Place the Seat Support Tube (37) on the Bench
Frame (5) so that the Seat Adjustment Bracket (45)
fits over the welded pin (not visible in the drawing) on
the side of the Bench Frame.
22
37
Lubricate
Lubricate an M10 x 80mm Bolt (56). Attach the Seat
Support Tube (37) to the indicated bracket on the
Bench Frame (5) with the Bolt and an M10 Nylon
Locknut (11). Note: Do not overtighten the Nylon
Locknut; the Seat Support Tube must pivot easily.
45
56
Welded
Pin
5
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
23. Turn the Seat (14) as shown. Attach the wide end of
the Seat to the bracket on the Seat Support Tube
(37) with two M6 x 16mm Screws (3).
23
14
Tilt the Seat Support Tube (37) upwards and attach
the narrow end of the Seat (14) to the Seat Support
Tube with an M6 x 38mm Bolt (60) and an M6
Washer (30).
37
30
60
3
24. Make sure that all parts are properly tightened before you use the weight bench. The use of all
remaining parts will be explained in ADJUSTING THE WEIGHT BENCH starting on the following page.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Weight Bench
This section explains how the weight bench is adjusted. See the included exercise guide for important informa-
tion about how to perform a variety of exercises and how to get the greatest benefit from your exercise program.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE LOCKING BAR AND SAFETY SPOTTERS
Before starting an exercise, position the barbell and the
Safety Spotters (23, 24) in the correct position for that
exercise.
1
1
To do this, stand in front of the cage and grip the Locking
Bar (34) with both hands. Turn the Locking Bar until the
two hooks disengage the slots in the Uprights (1). Move
the Locking Bar to a new position and turn the Locking
Bar until the hooks engage the slots in the Uprights.
Note: Always start an exercise with the barbell posi-
tioned at the lowest point to which it will move during
the exercise.
31
23
34
32
24
Position both Safety Spotters (23, 24) directly under the
Weight Gliders (31, 32).
USING THE SAFETY SPOTTERS
To move a Safety Spotter (23, 24 [not shown]) to a new
position, grip the handle on one side of the Spotter Hook
(61, 62 [not shown]) and pull the Spotter Hook out of the
slot in the Upright (1). Raise or lower the Safety Spotter
to a new position and turn the Spotter Hook until it
engages one of the slots in the Upright.
1
61
23
WARNING: Always set both safety spotters at the
same height.
Handle
ATTACHING WEIGHTS TO THE BARBELL
To use the Barbell (35), slide the desired amount of
weight (not included) onto each end of the Barbell.
Secure the weights with the Large Weight Clips (13).
33
Note: To use standard weights, the Weight Adapters (33)
should be removed from the Barbell (35). Attach weights
to the Barbell with the Small Weight Clips (not shown).
35
13
WARNING: Do not place more than 260 pounds on
the barbell. Always secure the weights with weight
clips when they are on the barbell. Always place
the same amount of weight on each side of the
barbell.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE BACKREST
15
To raise the Backrest (15), grip the end of the Backrest
with one hand and pull it upward. The Backrest
Handle
Adjustment Frame (36) will automatically lock into one of
the tabs on the bracket on the Bench Frame (5).
To lower the Backrest (15), grip the end of the Backrest
with one hand and pull it slightly upwards. Grip the handle
(not shown) on the right side of the Backrest Adjustment
Frame (36) with your other hand and pull the Backrest
Adjustment Frame free of the tabs on the bracket on the
Bench Frame (5). Lower the Backrest to the desired posi-
tion and lock the Backrest Adjustment Frame into the
desired tab on the bracket on the Bench Frame.
36
5
Adjustment
Bracket
ADJUSTING THE SEAT
To raise the Seat (14), lift the narrow end of the Seat until
the appropriate tab on the Seat Adjustment Bracket (45)
engages the welded pin (not shown) on the right side of
the Bench Frame (5).
To lower the Seat (14), use the handle on the Seat
Adjustment Bracket (45) to disengage the Seat
Adjustment Bracket from the pin. Lower the Seat to the
desired position and engage the appropriate tab on the
Seat Adjustment Bracket to the pin.
45
Handle
Pin
14
5
15
Download from Www.Somanuals.com. All Manuals Search And Download.
R1299A
Part ListÑModel No. IMBE41990
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
2
2
4
1
14
2
2
1
2
24
2
2
1
1
2
6
2
2
1
2
2
1
1
1
1
2
8
4
5
1
1
2
Upright
Brace
M6 x 16mm Screw
M6 x 55mm Bolt
Bench Frame
M10 Washer
Base
Crossbar
M8 x 80mm Bolt
50mm x 70mm Outer Cap
M10 Nylon Locknut
Large Support Plate
Large Weight Clip
Seat
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
#
1
1
1
1
2
2
8
4
4
2
2
1
8
2
2
8
2
2
10
2
13
1
1
1
1
4
1
1
1
1
1
1
Locking Bar
Barbell
Backrest Adjustment Bracket
Seat Support Tube
M8 x 30mm Bolt
M8 x 60mm Bolt
M10 x 65mm Carriage Bolt
M8 x 70mm Bolt
M10 x 65mm Bolt
M10 x 25mm Bolt
Large Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Seat Adjustment Bracket
M10 x 70mm Bolt
50mm Bushing
Backrest
25mm Bushing
Small Support Plate
50mm Square Outer Cap
Weight Guide
45mm x 45mm Bushing
M8 x 16mm Screw
25mm Round Inner Cap
M8 Washer
Small Weight Clip
Base Crossbar
Weight Storage Tube
M10 x 180mm Bolt
Right Safety Spotter
Left Safety Spotter
Small Stabilizer
Large Stabilizer
Backrest Tube
20mm x 40mm Inner Cap
38mm Bushing
M6 Washer
M8 x 25mm Bolt
M8 Nylon Locknut
M10 x 115mm Bolt
M10 x 80mm Bolt
15mm x 10.2 mm x 60mm Spacer
25mm x 50mm Inner Cap
M8 x 65mm Carriage Bolt
M6 x 38mm Bolt
Right Spotter Hook
Left Spotter Hook
UserÕs Manual
Right Weight Glider
Left Weight Glider
Weight Adapter
#
#
Exercise Guide
6mm Allen Wrench
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
R1299A
Exploded DrawingÑModel No. IMBE41990
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
¥ The MODEL NUMBER of the product (IMBE41990)
¥ The NAME of the product (IMAGE¨ 3.8 weight bench)
¥ The SERIAL NUMBER of the product (see the front cover of this manual)
¥ The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
IMAGE is a registered trademark of ICON Health & Fitness, Inc.
Part No. 160469 R1299A
Printed in China © 1999 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|